1.2-V Low-Power Multi-Mode DAC+Filter Blocks for Reconfigurable (WLAN/UMTS, WLAN/Bluetooth) Transmitters

Two versions of a baseband block composed by a 8-bit current-steering DAC and a fourth-order low-pass reconstruction filter are realized in a 0.13-$muhbox m$CMOS technology to be embedded in multistandard wireless transmitters. In order to satisfy the specifications of WLAN IEEE 802.11a/b/g, UMTS, and Bluetooth standards, the proposed devices can be digitally programmed, adjusting the DAC conversion frequency and the low-pass filter cut-off frequency. For the WLAN case, the DAC operating frequency and the filter bandwidth are set to 100 MHz and 11 MHz, respectively, for the UMTS case, they are equal to 50 MHz and 2.5 MHz, and for the Bluetooth case, they are equal to 50 MHz and 1 MHz. The first device is reconfigurable between WLAN and UMTS, and the second one between WLAN and Bluetooth. The two fabricated devices operate from a single 1.2-V supply voltage and occupy a 0.8$hbox mm^2$and 0.7$hbox mm^2$die area, respectively. The power consumption is optimized according to the operation mode and is 8 mW in WLAN mode, 8.4 mW in UMTS mode, and 5.4 mW in Bluetooth mode. For all the considered standards, the measured OIP3 is larger than 28 dBm, while the SFDR is 54 dB for WLAN, 61 dB for UMTS, and 63 dB for Bluetooth.     

A 10-bit 50-MS/s subsampling pipelined ADC based on SMDAC and opamp sharing

This paper describes a 10-bit,50-MS/s pipelined A/D converter(ADC) with proposed area- and power-efficient architecture.The conventional dedicated sample-hold-amplifier(SHA) is eliminated and the matching requirement between the first multiplying digital-to-analog converter(MDAC) and sub-ADC is also avoided by using the SHA merged with the first MDAC(SMDAC) architecture,which features low power and stabilization.Further reduction of power and area is achieved by sharing an opamp between two successive pi...     

Low-power CMOS fully-folding ADC with a mixed-averaging distributed T/H circuit

This paper describes an 8-bit 125 Mhzlow-powerCMOS fully-foldinganalog-to-digital converter(ADC).A novel mixed-averaging distributed T/H circuit is proposed to improve the accuracy. Folding circuits are not only used in the fine converter but also in the coarse one and in the bit synchronization block to reduce the number of comparators for low power. This ADC is implemented in 0.5μm CMOS technology and occupies a die area of 2 × 1.5 mm~2. The measured differential nonlinearity and integral nonlinearity are 0.6 LSB/-0.8 LSB and 0.9 LSB/-1.2 LSB, respectively. The ADC exhibits 44.3 dB of signal-to-noise plus distortion ratio and 53.5 dB of spurious-free dynamic range for 1 MHz input sine-wave. The power dissipation is 138 mW at a sampling rate of 125 MHz at a 5 V supply.     

A 150-MS/s 8-b 71-mW CMOS time-interleaved ADC

A pipelined analog-to-digital converter (ADC) architecture suitable for high-speed (150 MHz), Nyquist-rate A/D conversion is presented. At the input of the converter, two parallel track-and-hold circuits are used to separately drive the sub-ADC of a 2.8-b first pipeline stage and the input to two time-interleaved residue generation paths. Beyond the first pipeline stage, each residue path includes a cascade of two 1.5-b pipeline stages followed by a 4-b "backend" folding ADC. The full-scale residue range at the output of the pipeline stages is half that of the converter input range in order to conserve power in the operational amplifiers used in each residue path. An experimental prototype of the proposed ADC has been integrated in a 0.18-/spl mu/m CMOS technology and operates from a 1.8-V supply. At a sampling rate of 150 MSample/s, it achieves a peak SNDR of 45.4 dB for an input frequency of 80 MHz. The power dissipation is 71 mW.     

A power-efficient 10-bit 40-MS/s sub-sampling pipelined CMOS analog-to-digital converter

This paper presents a 10-bit 40-MS/s pipelined analog-to-digital converter (ADC) in a 0.13-μm CMOS process for subsampling applications. A simplified opamp-sharing scheme between two successive pipelined stages is proposed to reduce the power consumption. For subsampling, a cost-effective fast input-tracking switch with high linearity is introduced to sample the input signal up to 75 MHz. A two-stage amplifier with hybrid frequency compensation is developed to achieve both high bandwidth and large swing with low power dissipation. The measured result shows that the ADC achieves over 77 dB spurious free dynamic range (SFDR) and 57.3 dB signal-to-noise-plus-distortion ratio (SNDR) within the first Nyquist zone and maintains over 70 dB SFDR and 55.3 dB SNDR for input signal up to 75 MHz. The peak differential nonlinearity (DNL) and integral nonlinearity (INL) are ±0.2 LSB and ±0.3 LSB, respectively. The ADC consumes 15.6 mW at the sampling rate of 40 MHz from a 1.2-V supply voltage, and achieves a figure-of-merit (FOM) value of 0.22 pJ per conversion step.     

A 10-b 20-Msample/s low-power CMOS ADC

A single-ended input but internally differential 10 b, 20 Msample/s pipelined analog-to-digital converter (ADC) is demonstrated with 4 mW per stage using a single 5 V supply. The prototype ADC made of an input sample and hold (S/H) plus 8 identical unscaled pipelined stages consumes 50 mW including power consumed by a bias generator and two internal buffer amplifiers driving common-mode bias lines. Key circuits developed for this low-power ADC are a dynamic comparator with a capacitive reference voltage divider that consumes no static power, a source-follower buffered op amp that achieves wide bandwidth using large input devices, and a self-biased cascode biasing circuit that tracks power supply variation. The ADC implemented using a double-poly 1.2 μm CMOS technology exhibits a DNL of ±0.65 LSB and a SNDR of 54 dB while sampling at 20 MHz. The chip die area is 13 mm²     

A High Performance Track and Hold Circuit for High-Resolution High-Speed ADC

Design of a high performance track and hold (T/H) circuit for high-resolution high-speed analog-to-digital converter (ADC) is presented,which has been implemented in 0.18 μm CMOS process.An improved bootstrapped and bulk-switching technique is introduced to greatly minimize the nonlinearity of sampling network over a wide bandwidth,and the addition of a modified pre-charge circuit helps reducing the total power consumption.The experimental results show that the proposed T/H circuit achieves over 77 dB SFDR (spurious-free dynamic range) and 70 dB THD (total harmonic distortion) at 100 MHz sampling rate and maintains the performance with input frequency up to 305 MHz while consuming 47 mW power.     

A 13.5-mW 185-Msample/s ΔΣ modulator for UMTS/GSMdual-standard IF reception

A system-oriented approach for the design of a UMTS/GSM dual-standard ΔΣ modulator is presented to demonstrate the feasibility of achieving intermediate frequency (IF) around 100 MHz, high dynamic range, and low power consumption at the same time. The circuit prototype implements 78 MHz IF for GSM and 138.24 MHz for wideband code division multiple access (WCDMA), which are set to be 3/4 of the analog-to-digital converter sampling rate. A two-path IF sampling and mixing topology with a low-pass ΔΣ modulator, run at half the sampling rate, is used. Implemented in 0.25-μm CMOS, the circuit achieves dynamic range and peak signal-to-noise and distortion ratio for GSM of 86 and 72 dB, respectively. The corresponding values for WCDMA are 54 and 52 dB, respectively. Optimization is performed at all stages of design to minimize power consumption. The complete circuit consumes less than 11.5 mW for GSM and 13.5 mW for WCDMA at 2.5-V supply, of which 8 mW is due to the analog part     

A 12-bit 200-MS/s pipelined A/D converter with sampling skew reduction technique

This paper presents a 12-bit 200-MS/s dual channel pipeline analog-to-digital converter (ADC). The ADC is featured with a digital timing correction for reducing a sampling skew and the capacitor swapping for suppressing nonlinearities at the first stage in the pipelined ADC. The prototype ADC occupies 0.8×1.4 mm² in a 65-nm CMOS technology. The differential nonlinearity is less than 1.0 least significant bit with a 200 MHz sampling frequency. With a sampling frequency of a 200-MS/s and an input of a 2.4 MHz, the ADC, respectively, achieves a signal to noise-and-distortion ratio and a spurious-free dynamic range of 61.49 dB–70.71 dB while consuming of 112 mW at a supply voltage of 1.1 V.     

一种具有采样带宽补偿的高性能采样/保持电路

针对中频采样模数装换器中的宽带采样/保持电路,提出了一种新颖的电荷交换补偿(CEC)技术.该技术通过消除采样开关有限导通电阻的影响,补偿了采样带宽,并避免了时钟馈通和电荷注入的加剧.同时设计了具有AB类输出的低功耗两级运放,在1.8V电源下为该采样/保持提供了3V峰-峰值的输入范围.该采样/保持电路在100Ms/s的采样率下,对于200MHz输入信号达到了94dB的无杂散动态范围.在5.5pF的负载下,功耗仅为26mW.     

A compact digitally programmable reconfigurable filter for dual-mode BT/802.11b receivers

A new 4th-order reconfigurable (complex bandpass or normal lowpass) filter for implementing the channel select filter for dual-mode receivers adopting low-IF for Bluetooth (BT) and zero-IF for WLAN (IEEE 802.11b) is presented. It provides an alternative solution to the optimum low-power complex filter based on the current amplifier. The new filter avoids the employment of capacitor and/or resistor banks leading to an area efficient design solution while maintaining high linearity and relatively low power consumption. The center frequency in BT mode and the pole frequency in 802.11b mode are digitally tuned through programming active current division networks (CDNs). Experimental results obtained from 0.18 μm CMOS chips show that the proposed design offers improved characteristics over available solutions in terms of power consumption, spurious-free dynamic range (SFDR) and/or area. It achieves in-band SFDR of 65.3 dB for BT and 65.2 dB for 802.11b while it consumes 1.8 mW. Also, it offers image rejection of better than 59 dB.     

带2位/级的新型转换过程和自锁定比较器的6位600 MS/s 逐次逼近型模数转换器

本文提出了一个在600MHz采样率下的6位逐次逼近寄存器（SAR）。由于对ADC高速的追求,本设计借鉴了2位/级的思想,并在此基础上给出了2位/级的新型转换过程,解决了DAC之间不匹配问题并减少了功耗。同时,采用了改进的分布式比较器拓扑结构以获得速度。通过整合多比较器的输入端减小了时钟馈通效应和失调,引入比较器的自锁技术进一步减小了功耗。测量结果表明,在600MHz采样频率、5.6MHz输入频率下,得到信号与噪声加失真比（SNDR）为32.13 dB,无杂散动态范围（SFDR）为44.05 dB。当输入频率接近奈奎斯特时,SNDR / SFDR分别下降到28.46/39.20 dB。最终该ADC由TSMC 65纳米工艺制造,其设计面积为0.045 mm2。在1.2V电源电压下的功耗为5.01 mW,并得到FoM值为252 fJ/转换过程。     

一种12位50MS/s CMOS流水线A/D转换器

采用TSMC 0.18μm 1P6M工艺设计了一个12位50 MS/s流水线A/D转换器（ADC）。为了减小失真和降低功耗,该ADC利用余量增益放大电路（MDAC）内建的采样保持功能,去掉了传统的前端采样保持电路;采用时间常数匹配技术,保证输入高频信号时,ADC依然能有较好的线性度;利用数字校正电路降低了ADC对比较器失调的敏感性。使用Cadence Spectre对电路进行仿真。结果表明,输入耐奎斯特频率的信号时,电路SNDR达到72.19 dB,SFDR达到88.23 dB。当输入频率为50 MHz的信号时,SFDR依然有80.51 dB。使用1.8 V电源电压供电,在50 MHz采样率下,ADC功耗为128 mW。     

一种具有采样带宽补偿的高性能采样/保持电路

针对中频采样模数装换器中的宽带采样/保持电路,提出了一种新颖的电荷交换补偿（CEC）技术.该技术通过消除采样开关有限导通电阻的影响,补偿了采样带宽,并避免了时钟馈通和电荷注入的加剧.同时设计了具有AB类输出的低功耗两级运放,在1.8V电源下为该采样/保持提供了3V峰-峰值的输入范围.该采样/保持电路在100Ms/s的采样率下,对于200MHz输入信号达到了94dB的无杂散动态范围.在5.5pF的负载下,功耗仅为26mW.     

A 16-bit cascaded sigma-delta pipeline A/D converter

A low-noise cascaded multi-bit sigma-delta pipeline analog-to-digital converter (ADC) with a low oversampling rate is presented. The architecture is composed of a 2-order 5-bit sigma-delta modulator and a cascaded 4-stage 12-bit pipelined ADC, and operates at a low 8X oversampling rate, The static and dynamic performances of the whole ADC can be improved by using dynamic element matching technique. The ADC operates at a 4 MHz clock rate and dissipates 300 mW at a 5 V/3 V analog/digital power supply. It is developed in a 0.35 μm CMOS process and achieves an SNR of 82 dB.     

基于流水线ADC的高速数据采集系统设计

由于流水线模数转换器（ADC）能在较低的功耗条件下实现中、高精度高速数据采样功能,因而被广泛应用于雷达、通信、医学成像、精确控制等技术领域的数据采集系统。文章介绍了流水线ADC的基本原理及其最新研究成果,并且基于流水线ADC完成了一种14位精度125Msps高速数据采集系统的设计。测试结果表明,该系统在75Msps采样...     

A 9-b charge-to-digital converter for integrated image sensors

Charge-to-digital conversion offers advantages over conventional charge readout techniques because it performs digitization directly in the charge domain. The approach consolidates hardware, reduces power and weight, and eliminates many sources of noise and nonlinearity. This paper introduces an architecture for a charge-to-digital converter (CDC) that is tailored toward a charge-coupled device (CCD) implementation. New methods of generating charge, sensing charge, and comparing charge packets are described that improve conversion accuracy. Factors limiting device performance are discussed. Measured results are presented for two prototype CDCs. The first, using buried channel CCDs, is optimized for resolution. It achieves 56 dB spurious free dynamic range (SFDR) at a 2 MHz sampling rate and operates from 5 V. The second, using surface channel CCDs, is optimized for power and speed. It achieves 49 dB SFDR at a 15 MHz sampling rate and consumes 13 mW power at its maximum sampling rate of 22 MHz     

A systematic design approach for low-power 10-bit 100 MS/s pipelined ADC

A systematic design approach for low-power 10-bit, 100 MS/s pipelined analog-to-digital converter (ADC) is presented. At architectural level various per-stage-resolution are analyzed and most suitable architecture is selected for designing 10-bit, 100 MS/s pipeline ADC. At Circuit level a modified wide-bandwidth and high-gain two-stage operational transconductance amplifier (OTA) proposed in this work is used in track-and-hold amplifier (THA) and multiplying digital-to-analog converter (MDAC) sections, to reduce power consumption and thermal noise contribution by the ADC. The signal swing of the analog functional blocks (THA and MDAC sections) is allowed to exceed the supply voltage (1.8 V), which further increases the dynamic range of the circuit. Charge-sharing comparator is proposed in this work, which reduces the dynamic power dissipation and kickback noise of the comparator circuit. The bootstrap technique and bottom plate sampling technique is employed in THA and MDAC sections to reduce the nonlinearity error associated with the input signal resulting in a signal-to-noise-distortion ratio of 58.72/57.57 dB at 2 MHz/Nyquist frequency, respectively. The maximum differential nonlinearity (DNL) is +0.6167/−0.3151 LSB and the maximum integral nonlinearity (INL) is +0.4271/−0.4712 LSB. The dynamic range of the ADC is 58.72 dB for full-scale input signal at 2 MHz input frequency. The ADC consumes 52.6 mW at 100 MS/s sampling rate. The circuit is implemented using UMC-180 nm digital CMOS technology.     

A reconfigurable two-stage cyclic ADC for low-power applications in 3.3 V 0.35 µm CMOS

This article presents a reconfigurable pipeline analog-to-digital converter (ADC) using a two-stage cyclic configuration. The ADC consists of two stages with 1.5 effective bit resolution, two reference circuits for voltage and current biasing, and a clock generator and timing circuit. Throughout the development of this ADC, several techniques were combined for reducing the power consumption as well as for preserving the converter linearity. To reduce the power consumption, the circuit has a single operational trans-conductance amplifier shared by both pipeline stages. To keep conversion linearity, circuits such as the bootstrapped complementary metal-oxide semiconductor (CMOS) transmission gates and a robust comparator topology were implemented. The circuit can be configured to perform conversion between 7 and 15 bit resolutions, and it works with the master clock frequency in the range of 1 kHz to 40 MHz. The circuit has been prototyped in a 3.3 V 0.35 µm CMOS process and consumes 14.1 mW at 40 MHz and 8 MSample/s sampling rate. With this resolution and sampling rate, it achieves 60.1 dB SNR, 56.57 dB SINAD and 9.1 bit ENOB at 0.666 MHz input frequency and 53.6 dB SNR, 52.4 dB SINAD and 8.6 bit ENOB at 3.85 MHz input frequency. The technological FOM obtained was 13.2 A s/m².     

A 77-dB Dynamic Range, 7.5-MHz Hybrid Continuous-Time/Discrete-Time Cascaded $Sigma Delta$ Modulator

Although SigmaDelta modulators have largely been implemented as discrete-time (DT) circuits, a continuous-time (CT) approach offers significant advantages for realizing high-accuracy A/D converters at signal bandwidths where technology considerations may impose significant constraints. A CT design allows for relaxed amplifier unity-gain frequency and power requirements, which can enable the realization of high-resolution modulators with bandwidths of several MHz or more at low power. It also provides the advantage of inherent anti-aliasing filtering. This paper introduces a hybrid CT/DT SigmaDelta modulator for A/D conversion that combines the benefits of CT and DT circuits, while mitigating the challenges associated with CT design. The second-order first stage of a two-stage cascade is implemented in CT, while the first-order second stage is a DT circuit. An experimental prototype of the proposed modulator, integrated in 0.18-mum CMOS technology, operates from a 1.2-V analog supply to allow for easier migration to a 0.13-mum or 90-nm CMOS technology. The prototype achieves a dynamic range of 77 dB, a peak SNR of 71 dB, a peak SNDR of 67 dB, and worst-case anti-aliasing filtering of 48 dB for a signal bandwidth of 7.5 MHz and a sampling rate of 240 MHz. The total power dissipation is 89 mW, including 63.6 mW of analog power.