共查询到17条相似文献,搜索用时 78 毫秒
1.
连铸工艺对板坯裂纹的影响及防止措施 总被引:1,自引:0,他引:1
连铸坯的裂纹是造成连铸坯报废的主要原因,针对连铸板坯的宽面纵裂和角部横裂问题进行了金相组织检验和热模拟试验,对铸坯裂纹产生的原因和机理进行分析,提出了防止铸坯产生裂纹的具体措施。 相似文献
2.
3.
板坯连铸倒角结晶器的开发与应用 总被引:2,自引:0,他引:2
为减少连铸板坯角部横裂纹,在分析连铸坯角部横裂纹形成机制的基础上,提出了通过倒角结晶器减少角部横裂纹,以改变连铸板坯角部的二维传热,提高矫直时连铸坯的角部温度。数值模拟计算的结果表明,相对于直角连铸坯,倒角连铸坯在矫直区连铸坯角部温度明显提高,消除了角部Z向应力和应变集中。工业生产数据表明,采用倒角结晶器后,矫直区连铸坯角部温度从810~855℃提高到901~932℃,有效避开了钢的高温脆性区,连铸坯角部横裂纹发生率从10.6%稳定控制到1.6%以下,显著减少了连铸坯角部横裂纹。目前倒角结晶器稳定应用于首秦,所生产钢种涵盖了普碳钢、低合金钢、低碳钢和中碳含铌钢等。 相似文献
4.
5.
6.
7.
8.
9.
10.
连铸板坯裂纹的成因及防止措施 总被引:3,自引:0,他引:3
连铸板坯在实际生产中由于受冷却条件、保护渣性能、结晶器的结构以及振动方法等因素影响,常常产生表面裂纹、角部裂纹、星形裂纹等缺陷,造成轧后废,影响产量和质量。针对鞍钢1号板坯连铸机的实际情况,认为选择合适的保护渣,调整二冷水与改进拉速,避开钢在600 ̄900℃脆化温度范围,力求铸坯厚度均匀,减少应力集中,对于减少裂纹缺陷是非常重要的。 相似文献
11.
12.
针对攀钢连铸 Q2 35 G等包晶钢生产中出现的铸坯表面裂纹问题 ,在调查分析裂纹特征及其产生原因的基础上 ,发现保护渣传热过强和保护渣流入不均是诱发角横裂产生的主要原因。通过对保护渣结晶特性的研究 ,开发出了低碱度 (Ca O/ Si O2 <1.0 )、高结晶率的新型包晶钢用连铸保护渣。工业试验表明 ,研制的保护渣具有良好的使用效果 ,所浇铸坯表面质量优良 ,铸坯裂纹较少 ,表面角横裂发生率降低到 4 .19% ,纵裂发生率为 3.4 2 % ,且保护渣润滑作用良好 ,未发生漏钢事故。 相似文献
13.
为了更加有效控制和减少连铸坯的角部横裂纹质量缺陷,根据其形成的机制,针对两种新型铸坯模型,即圆角和倒角模型进行研究。通过建立特厚连铸矩形坯在凝固过程的传热模型并进行数值模拟,得到铸坯在凝固过程沿拉速方向上温度场和坯壳厚度的分布规律,并在此基础上建立热力耦合模型,分析铸坯的应力变化,讨论了产生裂纹的可能性。研究结果表明,通过对比传统直角模型,得出圆角和倒角模型对铸坯角部温度场和应力场两个方面的分布状况都有改善,即新铸坯模型角部温度在连铸矫直段有效避开了钢的高温脆性区,同时降低了铸坯角部的应力值,减小了角部裂纹产生的可能性。 相似文献
14.
本文主要对舞钢连铸板坯表面裂纹产生的原因进行分析,着重阐述在连铸生产中钢的化学成分,浇涛工艺参数,设备状况,保护渣等对铸坯表面裂纹的影响以及采取的措施。 相似文献
15.
《钢铁研究学报(英文版)》2011,(Z1):557-562
In order to reduce the transverse corner cracks of high strength weathering steel Q450NQR1,the factors influencing transverse corner cracks on continuously cast slab,such as level fluctuation of molten steel in mold,mold taper,primary cooling,mold powder,secondary cooling,nitrogen content in steel,spray nozzle structure,processing parameters and equipment of CC,etc.,were analyzed.Based on this,a series of comprehensive countermeasures have been proposed.The operation shows by the use of key technologies,including stabilizing steel level,optimizing the mold taper,weakening the primary cooling and the secondary cooling,reforming the mold powder,and adjusting spray nozzle structure,the transverse corner cracks on continuously cast slab have been significantly reduced,and the edge cracks on hot rolled sheet have been eliminated due to the transverse corner cracks.The qualified slabs are delivered to produce weathering cold forming sectional steel,whose yield strength is greater than 450MPa. 相似文献
16.
微合金化钢连铸坯角部横裂纹形成机制 总被引:1,自引:0,他引:1
为研究微合金钢连铸坯角部横裂纹缺陷形成机制问题,从理论上研究了连铸过程第二相粒子的析出行为,并在板坯连铸生产中进行"卧坯"试验。研究结果表明:X65管线钢中碳氮化钛、碳氮化铌、氮化铝的开始析出温度分别为1 508、1 123、1 165℃,析出峰值温度分别为1 360、870和840℃;"卧坯"试验发现结晶器内及垂直段无裂纹,在距弯月面3 270mm处,即对应于弯曲开始后710mm开始出现多处外弧横裂纹,而弧形段内无内弧裂纹,在弯曲段铸坯角部温度处于钢的第Ⅲ脆性区,同时外弧受拉应力,这是造成外弧角横裂产生的主要原因。 相似文献
17.
Mostafa Omar El-Bealy 《Metallurgical and Materials Transactions B》2014,45(3):988-1017
The aim of the current article is to elucidate the significant effects of macrosegregation distribution and its level on the different stages of interdendritic crack formation during dendritic solidification in continuously cast steel slabs. Couple formations of macrosegregation and interdendritic crack phenomena during dendritic solidification of peritectic carbon steels have been investigated by metallographic study of collected slab samples and by performing a set of mathematical analyses. The metallographic study involved plant trails to measure slab surface temperature of different secondary spray cooling conditions. Also, macro–microexaminations, measurements of dendrite arm spacing, macrosegregation analysis, and interdendritic distance between the dendrites of collected samples from plant trials have been performed. The experimental results show a fluctuation of carbon segregation with respect to distance from slab surface. These results also reveal that the interdendritic cracks vary with this fluctuation in various nano, macro, and microscales based on the cooling conditions. A mathematical model of heat transfer, solidification, structure evolution, interdendritic strain, macrosegregation, and elementary interdendritic area “EIA” has been developed. This model takes also into account the calculating of interdendritic distance between the dendrites “IDD” to evaluate the interdendritic crack width. The model predictions of different thermal and solidification phenomena show a good agreement with measurements. The results pointed out also that the coupled effect of interdendritic strain and macrosegregation phenomena and their distributions can be considered as the most important tools to evaluate the surface and internal interdendritic cracks in continuously cast steel slabs. The formation mechanisms of different types of interdendritic crack with interdendritic strain patterns and fluctuation of macrosegregation levels during various cooling zones have been explained, and the possible solutions to these problems have been discussed. 相似文献