Scaling of multidielectric nonvolatile SONOS memory structures

Present-day low-power, portable lap-top computers and consumer products require non-volatile semiconductor memory (NVSM) operating at 5 V with a trend towards reducing this level to 3.3 V. The SONOS technology, an acronym for the polySilicon-blocking Oxide-Nitride-tunnel Oxide-Silicon structure used in capacitors and transistors, shows promise as a technology for present and future low voltage NVSM applications. The nitride layer in the dielectric sandwich permits the storage of charge resulting in adjustable threshold voltages. This paper examines the physics and characterization of scaled SONOS NVSM transistors in relation to reducing the programming voltage. We develop a model for the transient characteristics of the SONOS NVSM transistor with: (1) a simple closed-form solution valid for short programming times; and (2) a numerical solution covering the entire range of programming times. The simple closed-form solution clearly illustrates the dependence of the turn-on time and erase/white slope on the dielectric thicknesses, initial stored charge in the nitride, and programming voltage. In particular, we have examined: (1) decreasing the tunnel oxide thickness; and (2) scaling the blocking oxide thickness. By properly scaling the dielectric films (11 Å tunnel oxide, 50 Å nitride, 40 Å blocking oxide), a ±8 V programmable SONOS device has been obtained with a 50 μs write time and a 100 μs erase time for a 3 V memory window, and a ±5 V programmable device with a 100 ms erase and write time for a 1.5 V memory window.     

Introduction to flash memory

This paper mainly focuses on the development of the NOR flash memory technology, with the aim of describing both the basic functionality of the memory cell used so far and the main cell architecture consolidated today. The NOR cell is basically a floating-gate MOS transistor, programmed by channel hot electron and erased by Fowler-Nordheim tunneling. The main reliability issues, such as charge retention and endurance, are discussed, together with an understanding of the basic physical mechanisms responsible. Most of these considerations are also valid for the NAND cell, since it is based on the same concept of floating-gate MOS transistor. Furthermore, an insight into the multilevel approach, where two bits are stored in the same cell, is presented. In fact, the exploitation of the multilevel approach at each technology node allows an increase of the memory efficiency, almost doubling the density at the same chip size, enlarging the application range and reducing the cost per bit. Finally, NOR flash cell scaling issues are covered, pointing out the main challenges. Flash cell scaling has been demonstrated to be really possible and to be able to follow Moore's law down to the 130-nm technology generations. Technology development and consolidated know-how is expected to sustain the scaling trend down to 90- and 65-nm technology nodes. One of the crucial issues to be solved to allow cell scaling below the 65-nm node is the tunnel oxide thickness reduction, as tunnel thinning is limited by intrinsic and extrinsic mechanisms.     

Nonvolatile Si quantum memory with self-aligned doubly-stacked dots

We propose a novel Si dot memory whose floating gate consists of self-aligned doubly stacked Si dots. A lower Si dot exists immediately below an upper dot and lies between thin tunnel oxides. It is experimentally shown that charge retention is improved compared to the usual single-layer Si dot memory. A theoretical model considering quantum confinement and Coulomb blockade in the lower Si dot explains the experimental results consistently, and shows that charge retention is improved exponentially by lower dot size scaling. It is shown that the retention improvement by lower dot scaling is possible, keeping the same write/erase speed as single dot memory, when the tunnel oxide thickness is adjusted simultaneously.     

The HIMOS flash technology: the alternative solution for low-cost embedded memory

The high-injection MOS (HIMOS) technology was initially developed as an application-specific memory technology, i.e., a nonvolatile block-erasable (Flash-type) memory for embedded applications. The label "embedded" points out that cost was considered to be the prime issue. Because of this, processing complexity and voltage reduction have been the major driving forces in the cell and process development rather than mere cell size scaling. Indeed, what really counts in embedded applications is the chip area per megabit rather than the cell size itself. Because the substantially high operating voltages of floating-gate-based memories are not being scaled, the peripheral area becomes the main bottleneck for most embedded applications. Also, cost has to be viewed in terms of masking steps and complexity or marginality of processing in general, especially in the case of embedded Flash, since the envisaged products have to be incorporated in a conventional CMOS line. To achieve this goal, a split-gate approach was adopted, which, combined with an additional program gate (PG), leads to maximized hot-electron efficiency at low voltages. As an additional major advantage, this PG allows the use of an electrically erasable programmable ROM-like threshold voltage window. This implies that the high threshold needs to be only slightly positive, while the low one could be strongly negative. Such a scheme allows very low excess charge levels (especially in the more critical off state), which greatly improves device reliability, while allowing further scaling of the tunnel oxide as compared with other Flash concepts. This allows further reduction of the program/erase voltages. Also, such a window provides a larger read current, which removes the necessity for wordline boosting during readout and therefore improves access time.     

Charge trapping memory devices employing multi-layered Ge/Si nanocrystals for storage fabricated with ALD and PLD methods

The Ge/Si nanocrystals on ultra thin high-k tunnel oxide Al2O3 were fabricated to form the charge trapping memory prototype with asymmetric tunnel barriers through combining the advanced atomic layer deposition (ALD) and pulse laser deposition (PLD)techniques. Charge storage characteristics in such memory structure have been investigated using capacitance-voltage (C-V) and capacitance-time (C-t) measurements. The results prove that both the two-layered and three-layered memory structures behave relatively qualified for the multi-level cell storage. The results also demonstrate that compared to electrons, holes reach a longer retention time even with an ultra thin tunnel oxide owing to the high band offset at the valence band between Ge and Si.     

Nonvolatile memory with a metal nanocrystal/nitride heterogeneous floating-gate

Heterogeneous floating-gates consisting of metal nanocrystals and silicon nitride (Si/sub 3/N/sub 4/) for nonvolatile memory applications have been fabricated and characterized. By combining the self-assembled Au nanocrystals and plasma-enhanced chemical vapor deposition (PECVD) nitride layer, the heterogeneous-stack devices can achieve enhanced retention, endurance, and low-voltage program/erase characteristics over single-layer nanocrystals or nitride floating-gate memories. The metal nanocrystals at the lower stack enable the direct tunneling mechanism during program/erase to achieve low-voltage operation and good endurance, while the nitride layer at the upper stack works as an additional charge trap layer to enlarge the memory window and significantly improve the retention time. The write/erase time of the heterogeneous stack is almost the same as that of the single-layer metal nanocrystals. In addition, we could further enhance the memory window by stacking more nanocrystal/nitride heterogeneous layers, as long as the effective oxide thickness from the control gate is still within reasonable ranges to control the short channel effects.     

Non-volatile memory based on silicon nanoclusters

Write/erase and charge retention characteristics of a memory element for the electrically programmable read-only memory based on the silicon/oxide_l/oxide_2/silicon_dot/oxide/semiconductor structure were simulated. An alternative high-κ dielectric (ZrO₂) was used as a blocking oxide and the second tunnel oxide. A thin low-κ dielectric (SiO₂) was used as the first tunneling oxide. Due to such a configuration, injection characteristics of tunneling SiO₂ in the write/erase mode can be significantly improved; hence, the response rate and injected charge can be increased. At the same time, the use of the sufficiently thick blocking and second tunneling layers allows injected charge retention for a long time. Programming by a pulse 10 ms long with an amplitude of ±11 V makes it possible to obtain a memory window of ～6 V in 10 years.     

包含双层半导体和金属纳米晶MOS电容的存储特性

制备了包含双层半导体和金属纳米晶的MOS电容结构,研究了其在非挥发性存储器领域的应用。利用真空电子束蒸发技术,在二氧化硅介质中得到了半导体硅纳米晶和金属镍纳米晶。与包含单层纳米晶的MOS电容相比,这种包含双层异质纳米晶的MOS电容显示出更大的存储能力,且保留性能得到改善。说明顶层的金属纳米晶作为一层额外的电荷俘获层可以通过直接隧穿机制进一步延长保留时间和提高平带电压漂移量。     

Memory characteristics of an MOS capacitor structure with double-layer semiconductor and metal heterogeneous nanocrystals

An MOS (metal oxide semiconductor) capacitor structure with double-layer heterogeneous nanocrystals consisting of semiconductor and metal embedded in a gate oxide for nonvolatile memory applications has been fabricated and characterized. By combining vacuum electron-beam co-evaporated Si nanocrystals and self-assembled Ni nanocrystals in a SiO_2 matrix, an MOS capacitor with double-layer heterogeneous nanocrystals can have larger charge storage capacity and improved retention characteristics compared to one with single-layer nanocrystals. The upper metal nanocrystals as an additional charge trap layer enable the direct tunneling mechanism to enhance the flat voltage shift and prolong the retention time.     

Direct exchange between silicon nanocrystals and tunnel oxide traps under illumination on single electron photodetector

In this paper we present the trapping of photogenerated charge carriers for 300 s resulted by their direct exchange under illumination between a few silicon nanocrystals (ncs-Si) embedded in an oxide tunnel layer (SiO_x = 1.5) and the tunnel oxide traps levels for a single electron photodetector (photo-SET or nanopixel). At first place, the presence of a photocurrent limited in the inversion zone under illumination in the I–V curves confirms the creation of a pair electron/hole (e–h) at high energy. This photogenerated charge carriers can be trapped in the oxide. Using the capacitance-voltage under illumination (the photo-CV measurements) we show a hysteresis chargement limited in the inversion area, indicating that the photo-generated charge carriers are stored at traps levels at the interface and within ncs-Si. The direct exchange of the photogenerated charge carriers between the interface traps levels and the ncs-Si contributed on the photomemory effect for 300 s for our nanopixel at room temperature.     

Statistical simulations for flash memory reliability analysis and prediction

In this paper, through the use of a recently proposed statistical model of stress-induced leakage current, we will investigate the reliability of actual flash memory technologies and predict future trends. We investigate either program disturbs (namely gate and drain disturbs) and data retention of state-of-the-art flash memory cells and use this model to correlate the induced threshold voltage shift to the typical outputs coming from oxide characterization, that are density, cross section, and energy level of defects. Physical mechanisms inducing the largest threshold voltage (V/sub T/) degradation will be identified and explained. Furthermore, we predict the effects of tunnel oxide scaling on flash memory data retention, giving a rule of thumb to scale the tunnel oxide while maintaining the same retention requirements.     

360-nm Photoluminescence from Silicon Oxide Films Embedded with Silicon Nanocrystals

Si-rich silicon oxide films were deposited by RF magnetron sputtering onto composite Si/SiO2 targets. After annealed at different temperature, the silicon oxide films embedded with silicon nanocrystals were obtained. The photoluminescenee（PL） from the silicon oxide films embedded with silicon nanocrystals was observed at room temperature. The strong peak is at 360 nm, its position is independent of the annealing temperature. The origin of the 360-nm PL in the silicon oxide films embedded with silicon nanoerystals was discussed.     

High-Program/Erase-Speed SONOS With In Situ Silicon Nanocrystals

In this letter, for the first time, we have successfully fabricated silicon-oxide-nitride-oxide-silicon (SONOS) devices with embedded silicon nanocrystals (Si-NCs) in silicon nitride using in situ method. This process is simple and compatible to modern IC processes. Different Si-NCs deposition times by in situ method were investigated at first. SONOS devices with embedded Si-NCs in silicon nitride exhibit excellent characteristics in terms of larger memory windows (> 5.5 V), lower operation voltage, high P/E speed, and longer retention time (> 10⁸ s for 13% charge loss).     

Nonvolatile flash memory device using Ge nanocrystals embedded in HfAlO high-/spl kappa/tunneling and control oxides: Device fabrication and electrical performance

We fabricated a nonvolatile Flash memory device using Ge nanocrystals (NCs) floating-gate (FG)-embedded in HfAlO high-/spl kappa/ tunneling/control oxides. Process compatibility and memory operation of the device were investigated. Results show that Ge-NC have good thermal stability in the HfAlO matrix as indicated by the negative Gibbs free energy changes for both reactions of GeO/sub 2/+Hf/spl rarr/HfO/sub 2/+Ge and 3GeO/sub 2/+4Al/spl rarr/2Al/sub 2/O/sub 3/+3Ge. This stability implies that the fabricated structure can be compatible with the standard CMOS process with the ability to sustain source-drain activation anneal temperatures. Compared with Si-NC embedded in HfO/sub 2/, Ge-NC embedded in HfAlO can provide more electron traps, thereby enlarging the memory window. It is also shown that this structure can achieve a low programming voltage of 6-7 V for fast programming, a long charge retention time of ten years maintaining a 0.7-V memory window, and good endurance characteristics of up to 10/sup 6/ rewrite cycles. This paper shows that the Ge-NC embedded in HfAlO is a promising candidate for further scaling of FG Flash memory devices.     

Investigation of reoxidation mechanisms in nitrided tunnel oxides for Flash memory applications

Aggressive scaling of Flash memory devices requires robust tunnel oxides to improve the cell performance while preserving the retention and endurance characteristics. In this context, reoxidation of the tunnel oxide has recently [2] been proposed as a promising technique. In this paper, we focus our investigations on the mechanisms related to radical (O^∗) or dry (O₂) reoxidation of nitrided tunnel oxides.     

BE-SONOS flash memory along with metal gate and high-k dielectrics in tunnel barrier and its impact on charge retention dynamics

We investigate the effect of a high-k dielectric in the tunnel layer to improve the erase speed-retention trade-off. Here, the proposed stack in the tunnel layer is AlLaO₃/HfAlO/SiO₂. These proposed materials possess low valence band offset with high permittivity to improve both the erase speed and retention time in barrier engineered silicon-oxide-nitride-oxide-silicon(BE-SONOS). In the proposed structure HfAlO and AlLaO₃ replace Si₃N₄ and the top SiO₂ layer in a conventional oxide/nitride/oxide(ONO) tunnel stack. Due to the lower conduction band offset(CBO) and high permittivity of the proposed material in the tunnel layer, it offers better program/erase(P/E) speed and retention time. In this work the gate length is also scaled down from 220 to 55 nm to observe the effect of high-k materials while scaling, for the same equivalent oxide thickness(EOT). We found that the scaling down of the gate length has a negligible impact on the memory window of the devices. Hence, various investigated tunnel oxide stacks possess a good memory window with a charge retained up to 87.4%(at room temperature) after a period of ten years. We also examine the use of a metal gate instead of a polysilicon gate, which shows improved P/E speed and retention time.     

Thickness scaling limitation factors of ONO interpoly dielectricfor nonvolatile memory devices

This paper describes the scaling limitation factors of ONO interpoly dielectric thickness, mainly considering the charge retention capability and threshold voltage stability for nonvolatile memory cell transistors with a stacked-gate structure, based on experimental results. For good intrinsic charge retention capability, either the top- or bottom-oxide thickness should be greater than around 6 nm. On the other hand, a thicker top oxide structure is preferable to minimize degradation due to defects. It has been confirmed that a 3.2 nm bottom-oxide shows detectable threshold voltage instability, but 4 nm does not. Effective oxide thickness scaling down to around 13 nm should be possible for flash memory devices with a quarter-micron design rule     

Charge transport in high-κ stacks for charge-trapping memory applications: A modeling perspective (invited)

Charge trapping (CT) memories could be a promising technology option for further NAND Flash scaling. The assessment of the scalability limits and ultimate performances of this technology demands for the comprehensive understanding of the physical mechanisms governing device operation and reliability, which requires accurate physics-based models reproducing the electrical device characteristics. The basic features of the models presented in the literature for CT memory devices are reviewed, underlining their similarities and differences, and highlighting their importance in order to achieve a comprehensive understanding of the physical mechanisms responsible for CT device operation and reliability. A physical model describing the charge transport in nitride and high-κ stacks is also presented, which allows gaining further insights into reliability issues related to charge localization and high-κ tunnel and blocking dielectrics, like the effects of the blocking alumina layer and the band-gap engineered tunnel dielectrics on the TANOS device retention.     

A three charge-states model for silicon nanocrystals nonvolatile memories

In the field of nonvolatile memories, substantial improvement of reliability is obtained by replacing the continuous polysilicon floating gate by a planar distribution of silicon nanocrystals, each acting as a storage node. The test devices in the present paper are MOS capacitors containing a two-dimensional layer of nanocrystals located 2.5 nm away from the oxide/substrate interface, inside the SiO/sub 2/. This work presents various measurements of the charge current versus either bias voltage or time. On the other side, the charge and discharge dynamics of the nanocrystals had already been described by De Salvo using a model borrowed from the conventional floating-gate memory. We show this approach to be not completely suitable to explain the experimental observations. Thus, we describe and apply a so-called granular model, based on a mono-electronic principle limited by Coulomb blockade, in which electrons interact with the nanocrystals one by one. Omitting the reality of such a one-by-one principle may involve important mistakes in the interpretation of phenomena.     

Flexible and transparent nanocrystal floating gate memory devices using silk protein

The charge storage behavior of a floating gate memory device using carbon nanotube-CdS nanostructures embedded in Bombyx mori silk protein matrix has been demonstrated. The capacitance – voltage characteristics in ITO/CNT–CdS-silk composite/Al device exhibits a clockwise hysteresis behavior due to the injection and storage of holes in the quantized valence band energy levels of CdS nanocrystals. The enhanced charge injection resulting in increase in memory window is observed at higher sweeping voltages. Nearly frequency independent hysteresis width over a wide range of 100 kHz–2.0 MHz, indicates its origin due to the charge storage in nanocrystals. The memory behavior of carbon nanotube–CdS nanostructures/silk nanocomposite devices has also been demonstrated on polyethylene terephthalate substrates, which may provide the way for flexible, transparent and printable electronic devices.