Influence of Ru segregation on the activity of Ru–Co/γ-Al2O3 during FT synthesis: A comparison with that of Ru–Co/SiO2 catalysts

γ-Al₂O₃ and SiO₂ supported Co catalysts, with varying amounts of Ru, were prepared and evaluated for Fischer–Tropsch synthesis (FTS). The composition of Ru for optimum activity was found to be support-dependent. The reducible Co₃O₄ was high in the region of 0–1.64 wt.% of Ru in Co/SiO₂ catalysts. Co/γ-Al₂O₃ displayed a maximum for reducible Co species at 0.42 wt.% Ru. Segregation of Ru occurred beyond this composition decreasing the extent of reduction. Co/γ-Al₂O₃ catalysts showed lower activity and olefin selectivity, in spite of higher Co dispersion, than Co/SiO₂ catalysts. The catalytic performance depends on the amount of reducible Co species, which again depends upon the optimum content of Ru.     

CO2 adsorption and activation over γ-Al2O3-supported transition metal dimers: A density functional study

Catalytic conversion of CO₂ to liquid fuels has the benefit of reducing CO₂ emission. Adsorption and activation of CO₂ on the catalyst surface are key steps of the conversion. Herein, we used density functional theory (DFT) slab calculations to study CO₂ adsorption and activation over the γ-Al₂O₃-supported 3d transition metal dimers (M₂/γ-Al₂O₃, M = Sc–Cu). CO₂ was found to adsorb on M₂/γ-Al₂O₃ negatively charged and in a bent configuration, indicating partial activation of CO₂. Our results showed that both the metal dimer and the γ-Al₂O₃ support contribute to the activation of the adsorbed CO₂. The presence of a metal dimer enhances the interaction of CO₂ with the substrate. Consequently, the adsorption energy of CO₂ on M₂/γ-Al₂O₃ is significantly higher than that on the γ-Al₂O₃ surface without the metal dimer. The decreasing binding strength of CO₂ on M₂/γ-Al₂O₃ as M₂ changes from Sc₂ to Cu₂ was attributed to decreasing electron-donation by the supported metal dimers. Hydroxylation of the support surface reduces the amount of charge transferred to CO₂ for the same metal dimer and weakens the CO₂ chemisorption bonds. Highly dispersed metal particles maintained at a small size are expected to exhibit good activity toward CO₂ adsorption and activation.     

Fischer–Tropsch synthesis: Effect of CO2 containing syngas over Pt promoted Co/γ-Al2O3 and K-promoted Fe catalysts

The effect of CO₂ was studied for cobalt and iron Fischer–Tropsch (FT) synthesis. CO₂ behaves differently in the presence of CO over cobalt and iron catalysts in terms of hydrogenation. A systematic increase of the CO₂ mole fraction of carbon in the feed gas mixture alters the product distribution dramatically for cobalt FT synthesis with CO₂ behaving like an inert gas at higher partial pressure of CO. With cobalt, CO appears to compete with CO₂ for adsorption. Using an iron FT catalyst, hydrogenation of CO₂ was effected due to the presence of the reverse water–gas shift activity of the catalyst which converts CO₂ to hydrocarbons through the formation of CO. Unlike the cobalt catalyst, the product distribution was only slightly altered with increasing CO₂ content in the feed gas mixture to the iron catalyst. This difference in behavior of CO₂ over cobalt and iron could be attributed to the absence of reverse water–gas shift activity on cobalt and hydrogenation of CO₂ to hydrocarbons—other than methane—will be derived through the formation of CO.     

High temperature SrCe0.9Eu0.1O3−δ proton conducting membrane reactor for H2 production using the water–gas shift reaction

The water–gas shift (WGS) reaction is used to shift the CO/H₂ ratio prior to Fischer–Tropsch synthesis and/or to increase H₂ yield. A WGS membrane reactor was developed using a mixed protonic–electronic conducting SrCe_0.9Eu_0.1O_3−δ membrane coated on a Ni–SrCeO_3−δ support. The membrane reactor overcomes the thermodynamic equilibrium limitations. A 46% increase in CO conversion and total H₂ yield was achieved at 900 °C under 3% CO and 6% H₂O, resulting in a 92% single pass H₂ production yield and 32% single pass yield of pure permeated H₂.     

Performance of Pd catalysts supported on nanocrystalline α-Al2O3 and Ni-modified α-Al2O3 in selective hydrogenation of acetylene

Nanocrystalline α-Al₂O₃ and Ni-modified α-Al₂O₃ have been prepared by sol–gel and solvothermal methods and employed as supports for Pd catalysts. Regardless of the preparation method used, NiAl₂O₄ spinel was formed on the Ni-modified α-Al₂O₃ after calcination at 1150 °C. However, an addition of NiO peaks was also observed by X-ray diffraction for the solvothermal-made Ni-modified α-Al₂O₃ powder. Catalytic performances of the Pd catalysts supported on these nanocrystalline α-Al₂O₃ and Ni-modified α-Al₂O₃ in selective hydrogenation of acetylene were found to be superior to those of the commercial α-Al₂O₃ supported one. Ethylene selectivities were improved in the order: Pd/Ni-modified α-Al₂O₃–sol–gel > Pd/Ni-modified α-Al₂O₃-solvothermal ≈ Pd/α-Al₂O₃–sol–gel > Pd/α-Al₂O₃-solvothermal  Pd/α-Al₂O₃-commerical. As revealed by NH₃ temperature program desorption studies, incorporation of Ni atoms in α-Al₂O₃ resulted in a significant decrease of acid sites on the alumina supports. Moreover, XPS revealed a shift of Pd 3d binding energy for Pd catalyst supported on Ni-modified α-Al₂O₃–sol–gel where only NiAl₂O₄ was formed, suggesting that the electronic properties of Pd may be modified.     

Effects of the preparation methods on the performance of the Cu–Cr–Fe/γ-Al2O3 catalysts for the synthesis of 2-methylpiperazine

Co-precipitation, impregnation and ultrasonic sol–gel (USG) methods have been used to prepare Cu–Cr–Fe/γ-Al₂O₃ catalysts, which were further used to synthesize 2-methylpiperazine. The catalysts were characterized by XRD, XPS, TG/DSC, BET, TPR, AAS and TEM. It is found that preparation method can greatly impact the catalytic performance of the catalysts, the Cu–Cr–Fe/γ-Al₂O₃ catalyst prepared by the ultrasonic sol–gel method proved to be the most active and stable for this reaction. The dispersion and stabilization of Cu⁰ in the reduced catalysts are attributed to the existence of CuCr₂O₄ and Fe₂O₃. A surprising copper migration was detected by XPS analysis for the Cu–Cr–Fe/γ-Al₂O₃-USG catalyst after the calcination process, which may be crucial to the high activity and stability of this catalyst.     

The functionalities of Pt/γ-Al2O3 catalysts in simultaneous HDS and HDA reactions

A Pt/γ-Al₂O₃ catalyst was tested in simultaneous hydrodesulfurization (HDS) of dibenzothiophene and hydrodearomatization (HDA) of naphthalene reactions. Samples of it were subjected to different pretreatments: reduction, reduction–sulfidation, sulfidation with pure H₂S and non-activation. The reduced catalyst presented the best performance, even comparable to that of Co(Ni)Mo catalysts. All catalyst samples were selective to the HDS reaction over HDA, and to the direct desulfurization pathway of dibenzothiophene HDS over the hydrogenation reaction pathway of HDS. The effect of H₂S partial pressure on the functionalities of the reduced Pt/γ-Al₂O₃ catalyst was studied. The results showed that an increase in H₂S partial pressure does not cause poisoning, but an inhibition effect, without changing the catalyst selectivity. Accordingly, the activity trends were ascribed to adsorption differences between the different reactive molecules over the same catalytic active site. TPR characterization along with a thermodynamics analysis showed that the active phase of reduced Pt/γ-Al₂O₃ is constituted by Pt⁰ particles. However, presulfidation of the catalyst leads to a mixture of PtS and Pt⁰ which has a negative effect on the catalytic performance without changing catalyst functionalities.     

Intrinsic kinetics of Fischer–Tropsch reactions over an industrial Co–Ru/γ-Al2O3 catalyst in slurry phase reactor

The rate of Fischer–Tropsch synthesis over an industrial well-characterized Co–Ru/γ-Al₂O₃ catalyst was studied in a laboratory well mixed, continuous flow, slurry reactor under the conditions relevant to industrial operations as follows: temperature of 200–240 °C, pressure of 20–35 bar, H₂/CO feed ratio of 1.0–2.5, gas hourly space velocity of 500–1500 N cm³ g_cat^− 1 h^− 1 and conversions of 10–84% of carbon monoxide and 13–89% of hydrogen. The ranges of partial pressures of CO and H₂ have been chosen as 5–15 and 10–25 bar respectively. Five kinetic models are considered: one empirical power law model and four variations of the Langmuir–Hinshelwood–Hougen–Watson representation. All models considered incorporate a strong inhibition due to CO adsorption. The data of this study are fitted fairly well by a simple LHHW form − R_H2 + CO = ap_H2^0.988p_CO^0.508 / (1 + bp_CO^0.508)² in comparison to fits of the same data by several other representative LHHW rate forms proposed in other works. The apparent activation energy was 94–103 kJ/mol. Kinetic parameters are determined using the genetic algorithm approach (GA), followed by the Levenberg–Marquardt (LM) method to make refined optimization, and are validated by means of statistical analysis. Also, the performance of the catalyst for Fischer–Tropsch synthesis and the hydrocarbon product distributions were investigated under different reaction conditions.     

Effect of Ru addition to Co/SiO2/HZSM-5 catalysts on Fischer–Tropsch synthesis of gasoline-range hydrocarbons

Microporous HZSM-5 zeolite and mesoporous SiO₂ supported Ru–Co catalysts of various Ru adding amounts were prepared and evaluated for Fischer–Tropsch synthesis (FTS) of gasoline-range hydrocarbons (C₅–C₁₂). The tailor-made Ru–Co/SiO₂/HZSM-5 catalysts possessed both micro- and mesopores, which accelerated hydrocracking/hydroisomerization of long-chain products and provided quick mass transfer channels respectively during FTS. In the same time, Ru increased Co reduction degree by hydrogen spillover, thus CO conversion of 62.8% and gasoline-range hydrocarbon selectivity of 47%, including more than 14% isoparaffins, were achieved simultaneously when Ru content was optimized at 1 wt% in Ru–Co/SiO₂/HZSM-5 catalyst.     

Reaction performance and characterization of Co/Al2O3 Fischer–Tropsch catalysts promoted with Pt, Pd and Ru

A series of noble metal (Pt, Ru or Pd) promoted Co/Al₂O₃ catalysts were prepared by sequential impregnation method. The catalysts were characterized by XRD, TPR, H₂-TPD and TPSR techniques, and their catalytic performance in Fischer–Tropsch synthesis was investigated in a fixed-bed reactor. The results of activity measurements show that the addition of small amounts of noble metal greatly improved the activity of the Co/Al₂O₃ catalyst. TPR experimental results demonstrate that hydrogen spillover from the noble metal to cobalt oxide clusters facilitated the reduction of cobalt oxide and, thus significantly increased the reducibility of Co/Al₂O₃ catalyst. The presence of noble metal increased the amount of chemisorbed hydrogen and weakened the bond strength of Co–H. TPSR results indicate that CO was adsorbed in a more reactive state on the promoted catalysts.     

Sintering kinetics of α-Al2O3 powder

The sintering kinetics of α-Al₂O₃ powder are reviewed in this paper. The initial sintering of α-Al₂O₃ micropowder and α-Al₂O₃ nanopowder is all controlled by grain boundary diffusion. The sintering kinetics dominate up to a relative density of 0.77, where the coarsening kinetics dominate during further densification. Herring's scaling law can be used to predict the approximate sintering temperature of α-Al₂O₃ powder and demonstrates that if the particle size can be reduced to <20 nm, sintering below 1000°C may be possible. ©     

Hydrodesulphurization performance of NiW/TiO2-Al2O3 catalyst for ultra clean diesel

TiO₂-Al₂O₃ binary oxide supports were obtained by sol–gel methods from Tetra-n-butyl-titanate and pseudoboehmite/aluminium chloride resources. The typical physico-chemical properties of NiW/TiO₂-Al₂O₃ catalysts with different TiO₂ loadings and their supports were characterized by means of BET, XRD and UV–vis DRS, etc. The BET results indicated that the specific surface areas of NiW/TiO₂-Al₂O₃ catalysts were as higher as that over pure γ-Al₂O₃ support, and the pore diameters were also large. The XRD and UV–vis DRS analyzing results showed that the Ti-containing supported catalysts existed as anatase TiO₂ species and the incorporation of TiO₂ could adjust the interaction between support and active metal, and impelled the higher reducibility of tungsten. The hydrodesulphurization (HDS) performance of the series catalysts were evaluated with diesel feedstock in a micro-reactor unit, and the HDS results showed that NiW/TiO₂-Al₂O₃ catalysts exhibited higher activities of ultra deep hydrodesulphurization of diesel oil than that of NiW/Al₂O₃ catalyst. The optimal TiO₂ content of NiW/TiO₂-Al₂O₃ catalysts was about 15 m%, and the corresponding HDS efficiency could reach to 100%. The sulphur contents of diesel products over NiW/TiO₂-Al₂O₃ (from pseudoboehmite/AlCl₃) catalysts with suitable TiO₂ content could be less than 15 ppmw, which met the sulphur regulation of Euro IV specification of ultra clean diesel fuel.     

Carbon dioxide reforming of ethanol over Ni/Y2O3–ZrO2 catalysts

Supported nickel catalysts of composition Ni/Y₂O₃–ZrO₂ were synthesized in one step by the polymerization method and compared with a nickel catalyst prepared by wet impregnation. Stronger interactions were observed in the formed catalysts between NiO species and the oxygen vacancies of the Y₂O₃–ZrO₂ in the catalysts made by polymerization, and these were attributed to less agglomeration of the NiO during the synthesis of the catalysts in one step. The dry reforming of ethanol was catalyzed with a maximum CO₂ conversion of 61% on the 5NiYZ catalyst at 800 °C, representing a better response than for the catalyst of the same composition prepared by wet impregnation.     

Development of a multi-layered micro-reactor coated with Pt–Co/Al2O3 catalyst for preferential oxidation of CO

Pt–Co/Al₂O₃ catalysts were prepared with different Co/Pt weight ratios (0.3–1.8) and their performances for preferential oxidation of CO (PROX) were tested. The activity of the catalyst increased with Co/Pt weight ratio due to the increase of the area of active phase by interaction between Pt and Co species. The 13-layered micro-channel reactor was prepared by stacking the plates coated with Pt–Co/Al₂O₃ catalyst. The reactor was divided into three parts (inlet, middle, and outlet) to evaluate the performance of each part. Most of O₂ supplied was depleted at the inlet part and the temperature gradient of the reactor occurred due to the high exothermicity of oxidations of CO and hydrogen. In order to prevent hot spot and temperature gradient, the reactor with non-uniform distribution of the catalyst (partially coating the catalyst on the channels) was prepared. The prepared reactor showed uniform temperature distribution and exhibited excellent performance for PROX.     

Silica-supported rhodium-cobalt catalysts for Fischer–Tropsch synthesis

The effects of the addition of Ag, Au, or Rh to a 15 wt% Co/SiO₂ catalyst on the Fischer–Tropsch (FT) synthesis were studied. Both Au and Rh showed a promoting effect on the FT activity, whereas the addition of Ag decreased the activity. The addition of a small amount of Rh (0.1–0.5 wt%) increased the CO conversion by 50% without affecting the selectivity. It was found that Rh catalyzed the reduction of cobalt oxides, but it did not change the number of surface cobalt atoms. It is proposed that the higher activity of Rh-promoted catalysts is due to the hydrogen spillover from Rh to Co during FT synthesis.     

Influence of the oxygen pretreatment on the CO2 reforming of methane on Ni/β-SiC catalyst

The influence of the O₂ pretreatment on the CO₂ reforming of methane to synthesis gas has been investigated with Ni catalysts supported on β-SiC extrudate. The structure and properties of the catalysts were characterised by SEM, TEM and XRD techniques. The pretreatment of the catalyst by a mixture of CO₂ and O₂ significantly improves the catalytic activity for the CO₂ reforming. On the Ni 5 wt.% supported on β-SiC catalyst, the CH₄ conversion has reached 90% with the O₂ pretreatment instead of 80% by direct activation under CO₂/CH₄ mixture. The oxygen pretreatment seems to stabilize the metallic nickel phase instead of NiSi₂.     

Synergetic effect of combined use of Cu–ZnO–Al2O3 and Pt–Al2O3 for the steam reforming of methanol

Commercial Cu–ZnO–Al₂O₃ catalysts are used widely for steam reforming of methanol. However, the reforming reactions should be modified to avoid fuel cell catalyst poisoning originated from carbon monoxide. The modification was implemented by mixing the Cu–ZnO–Al₂O₃ catalyst with Pt–Al₂O₃ catalyst. The Pt–Al₂O₃ and Cu–ZnO–Al₂O₃ catalyst mixture created a synergetic effect because the methanol decomposition and the water–gas shift reactions occurred simultaneously over nearby Pt–Al₂O₃ and Cu–ZnO–Al₂O₃ catalysts in the mixture. A methanol conversion of 96.4% was obtained and carbon monoxide was not detected from the reforming reaction when the Pt–Al₂O₃ and Cu–ZnO–Al₂O₃ catalyst mixture was used.     

Size effects on χ- to α-Al2O3 phase transformation

Nano-scaled χ-Al₂O₃ powders with d₅₀ mean particle sizes from 17 to 314 nm were prepared to investigate the size effect on their phase transformation. Structural properties and crystallization behavior as a function of thermal treatments of various-sized χ-Al₂O₃ particles were examined by DTA, XRD and TEM characterizations. It was confirmed that the decrease of particle size allows for stable α-Al₂O₃ formation at relatively low temperature. Furthermore, the phase transformation route of χ-Al₂O₃ to α-Al₂O₃ was also modified due to the decrease of particle size. A critical size of χ-Al₂O₃ that determines the phase transformation behavior was found to be around 40 nm. For particles larger than 40 nm, a transition phase of κ-Al₂O₃ is formed before obtaining final α-Al₂O₃ phase. Nevertheless, for those smaller than the critical size, starting χ-Al₂O₃ particles have to grow to 40 nm and then directly transform to α-Al₂O₃ bypassing κ-Al₂O₃ at a temperature as low as 1050 °C.     

The effect of sodium on the catalytic activity of ZnO–Al2O3/ZSM-5 and SnO–Al2O3/ZSM-5 for the transesterification of vegetable oil with methanol

In order to elucidate the effect of sodium on the activity of ZSM-5 supported metal oxides catalysts (ZnO–Al₂O₃/ZSM-5 and SnO–Al₂O₃/ZSM-5) for the transesterification of soybean oil with methanol, ZSM-5 supported metal oxides were prepared with and without sodium hydroxide by impregnation. The metal compositions of the ZSM-5 supported metal oxide catalysts and the metal concentrations dissolved from the catalysts to the methylester phase were measured by SEM-EDS and inductive coupled plasma spectroscopy, respectively. The catalytic activity of ZnO–Al₂O₃/ZSM-5 and SnO–Al₂O₃/ZSM-5 containing sodium did not originate from surface metal oxides sites, but from surface sodium sites or dissolved sodium leached from the catalyst surface.     

Study of ruthenium supported on Ta2O5–ZrO2 and Nb2O5–ZrO2 as catalysts for the partial oxidation of methane

Ru-based catalysts supported on Ta₂O₅–ZrO₂ and Nb₂O₅–ZrO₂ are studied in the partial oxidation of methane at 673–873 K. Supports with different Ta₂O₅ or Nb₂O₅ content were prepared by a sol–gel method, and RuCl₃ and RuNO(NO₃)₃ were used as precursors to prepare the catalysts (ca. 2 wt.% Ru). At 673 K high selectivity to CO₂ was found. An increase of temperature up to 773 K produced an increase in the selectivity to syngas (H₂/CO = 2.2–3.1), and this is related with the transformation of RuO₂ to metallic Ru as was determined from XRD and XPS results. At 873 K and with co-fed CO₂ an increase of the catalytic activity and CO selectivity was found. A TOF value of 5.7 s⁻¹ and H₂/CO ratio ca. 1 was achieved over Ru(Cl)/6TaZr. Catalytic results are discussed as a function of the support composition and characteristics of Ru-based phases.