Electrochemical insertion of lithium and sodium into (MoO2)2P2O7

Insertion of lithium and sodium into phosphate (MoO₂)₂P₂O₇ was investigated electrochemically to determine the usefulness as a possible cathode for ion-transfer secondary batteries. Specific charges of up to 250 mA h g⁻¹ were obtained for A/(MoO₂)₂P₂O₇ (A: Li, Na) cells with liquid organic electrolytes in the first reduction half-cycle at room temperature. Intercalation processes under constant current densities of 0.2 mA cm⁻² were reversible within the range of composition 0.85<x<4.0 for lithium and 0.5<x<3.1 for sodium in A_x(MoO₂)₂P₂O₇ (A: Li, Na), respectively. Structural changes induced by lithium or sodium intercalation were followed by ex situ X-ray diffraction measurements, and the phase change from the crystal to the amorphous was observed in both cases.     

Performance of a polyaniline(DMcT)/carbon fiber composite as cathode for rechargeable lithium batteries

The redox reaction of 2,5-dimercapto-1,3,4-thiadiazole (DMcT) is slow at room temperature, but it can be accelerated when the electron transfer reaction is coupled with that of polyaniline (Pani). Films of polyaniline were electrosynthesized onto carbon fiber substrates by cyclic voltammetry from a 0.5 mol L⁻¹ H₂SO₄/0.1 mol L⁻¹ aniline aqueous solution; DMcT was incorporated into the films by two different procedures: A – previous adsorption on the carbon fiber substrate, and B – electropolymerization onto a Pani film from a 20 mmol L⁻¹ DMcT solution in acetonitrile. The Pani(DMcT)/carbon fiber composites were tested as cathodes at 0.1 mA cm⁻² in a cell containing lithium as anode in a 0.5 mol L⁻¹ LiClO₄ solution in propylene carbonate, in a dry box under an argon atmosphere at 25 ± 2 °C. Discharge capacity values of 159 mA h g⁻¹ (after 90 cycles) and 39 mA h g⁻¹ (after 50 cycles) were obtained for the composites prepared by procedures A and B, respectively. The high capacity value and the high electrochemical stability during the cycling indicate that there is a synergetic effect of Pani and DMcT in the composites prepared by procedure A.     

Synthesis and electrochemical properties of lithium cobalt oxides prepared by molten-salt synthesis using the eutectic mixture of LiCl–Li2CO3

Lithium cobalt oxide powders have been successfully prepared by a molten-salt synthesis (MSS) method using a eutectic mixture of LiCl and Li₂CO₃ salts. The physico-chemical properties of the lithium cobalt oxide powders are investigated by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), particle-size analysis and charge–discharge cycling. A lower temperature and a shorter time (∼700°C and 1 h) in the Li:Co=7 system are sufficient to prepare single-phase HT-LiCoO₂ powders by the MSS method, compared with the solid-state reaction method. Charge–discharge tests show that the lithium cobalt oxide prepared at 800°C has an initial discharge capacity as high as 140 mA h g⁻¹, and 100 mA h g⁻¹ after 40 cycles. The dependence of the synthetic conditions of HT-LiCoO₂ on the reaction temperature, time and amount of flux with respect to starting oxides is extensively investigated.     

NbSb2 as an anode material for Li-ion batteries

Polycrystalline samples of NbSb₂ have been synthesized and studied as anode material for lithium-ion batteries. The reaction mechanism of lithium with NbSb₂ is investigated by ex situ XRD and cyclic voltammogram studies. Li₃Sb and Nb are formed during first discharge and during charge lithium is extracted from Li₃Sb. The first cycle discharge capacity is 420 mA hg⁻¹ and first cycle charge capacity is 315 mA hg⁻¹.     

Si–O network encapsulated graphite–silicon mixtures as negative electrodes for lithium-ion batteries

Graphite–silicon mixtures are encapsulated in a Si–O network derived from sol–gel transformation of alkoxy-silane(methyl-trimethoxy-silane). The composites are characterized by powder X-ray diffraction and scanning electron microscopy. The catalyst used in the sol–gel process significantly affects the electrochemical properties of the composites. The initial specific capacity of the composites is close to 500 mA h g⁻¹, which is between that of graphite alone (∼300 mA h g⁻¹) and mechanical mixtures of graphite and silicon of identical silicon contents (∼900 mA h g⁻¹). Base (NH₄OH) catalyzed composites perform substantially better than acid (HCl) catalyzed composites. The experimental results have yet to demonstrate any real advantage of the composites over graphite in terms of cycleability. Nevertheless, this approach should not be dismissed as the network material in this study may not have been optimized.     

Solid-state Li/LiFePO4 polymer electrolyte batteries incorporating an ionic liquid cycled at 40 °C

The cycle behaviour and rate performance of solid-state Li/LiFePO₄ polymer electrolyte batteries incorporating the N-methyl-N-propylpyrrolidinium bis(trifluoromethanesulfonyl)imide (PYR₁₃TFSI) room temperature ionic liquid (IL) into the P(EO)₂₀LiTFSI electrolyte and the cathode have been investigated at 40 °C. The ionic conductivity of the P(EO)₂₀LiTFSI + PYR₁₃TFSI polymer electrolyte was about 6 × 10⁻⁴ S cm⁻¹ at 40 °C for a PYR₁₃⁺/Li⁺ mole ratio of 1.73. Li/LiFePO₄ batteries retained about 86% of their initial discharge capacity (127 mAh g⁻¹) after 240 continuous cycles and showed excellent reversible cyclability with a capacity fade lower than 0.06% per cycle over about 500 cycles at various current densities. In addition, the Li/LiFePO₄ batteries exhibited some discharge capability at high currents up to 1.52 mA cm⁻² (2 C) at 40 °C which is very significant for a lithium metal-polymer electrolyte (solvent-free) battery systems. The addition of the IL to lithium metal-polymer electrolyte batteries has resulted in a very promising improvement in performance at moderate temperatures.     

Electrochemical lithium insertion into amorphous MoO3·2H2O

Following the route of synthesis of β-MoO₃ through soft chemistry methods a new amorphous material with composition MoO₃·2H₂O has been detected. The hydrated molybdenum oxide showed the capacity for electrochemical lithium insertion. The maximum amount of lithium incorporated in this material (∼3.3 Li/Mo) leads to a specific capacity of 490 Ah kg⁻¹. The charge–discharge curve showed a good reversibility in the potential range from 3.2 to 1.1 V versus Li⁺/Li⁰ where the cell voltage decreased monotonously as a function of the degree of lithium inserted. The electrochemical features of amorphous MoO₃·2H₂O suggest that it can be considered as a possible cathode candidate in rechargeable lithium batteries.     

Electrochemical properties of iodine-containing lithium manganese oxide spinel

Iodine-containing, cation-deficient, lithium manganese oxides (ICCD-LMO) are prepared by reaction of MnO₂ with LiI. The MnO₂ is completely transformed into spinel-structured compounds with a nominal composition of Li_1−δMn_2−2δO₄I_x. A sample prepared at 800 °C, viz. Li_0.99Mn_1.98O₄I_0.02, exhibits an initial discharge capacity of 113 mA h g⁻¹ with good cycleability and rate capability in the 4-V region. Iodine-containing, lithium-rich lithium manganese oxides (ICLR-LMO) are also prepared by reaction of LiMn₂O₄ with LiI, which results in a nominal composition of Li_1+xMn_2−xO₄I_x. Li_1.01Mn_1.99O₄I_0.02 shows a discharge capacity of 124 mA h g⁻¹ on the first cycle and 119 mA h g⁻¹ a on the 20th cycle. Both results indicate that a small amount of iodine species helps to maintain cycle performance.     

Preparation and characterization of high-density spherical Li4Ti5O12 anode material for lithium secondary batteries

Li₄Ti₅O₁₂ is a very promising anode material for lithium secondary batteries. A novel technique has been developed to prepare Li₄Ti₅O₁₂. The spherical precursor is prepared via an “inner gel” method by TiCl₄ as the raw material. Spherical Li₄Ti₅O₁₂ powders are synthesized by sintering the mixture of spherical precursor and Li₂CO₃. The investigation of XRD, SEM and the determination of the electrochemical properties show that the Li₄Ti₅O₁₂ powders prepared by this method are spherical, and have high tap-density and excellent electrochemical performance. It is tested that the tap-density of the product is as high as 1.64 g cm⁻³, which is remarkably higher than the non spherical Li₄Ti₅O₁₂. Between 1.0 and 3.0 V versus Li, a reversible capacity is as high as 161 mAh g⁻¹ at a current density of 0.08 mA cm⁻².     

Development of high energy density small flat spiral cells and battery pack based on lithium/carbon monofluoride (Li/CFx)

Small spiral-wound lithium–carbon monofluoride (Li/CF_x) cells, which were discharged at the C/40 rate, had a nominal capacity of 300 mAh and a gravimetric energy density of about 464 Wh kg⁻¹. These cells delivered pulse current loads (>22 mA) with good capacity (>200 mAh) if they were subjected to a pre-discharge step. A 17 V, 2.2 kW battery based on Li/CF_x flat cell technology has also been fabricated and tested. The battery had gravimetric and volumetric energy densities of 360 Wh kg⁻¹ and 700 Wh dm⁻³, respectively. This compares with a value of 330 Wh kg⁻¹ and 522 Wh dm⁻³ for an equivalent battery based on Li/SOCl₂.     

LiMn2O4 cathode materials synthesized by the cellulose–citric acid method for lithium ion batteries

A new technique was employed to synthesize spinel LiMn₂O₄ cathode materials by adding cellulose and citric acid to an aqueous solution of lithium and manganese salts. Various synthesis conditions such as the calcination temperature and the citric acid-to-metal ion molar ratio (R) were investigated to determine the ideal conditions for preparing LiMn₂O₄ with the best electrochemical characteristics. The optimal synthesis conditions were found to be R = 1/3 and a calcination temperature of 800 °C. The initial discharge capacity of the material synthesized using the optimal conditions was 134 mAh g⁻¹, and the discharge capacity after 40 cycles was 125 mAh g⁻¹, at a current density of 0.15 mA cm⁻² between 3.0 and 4.35 V. Details of how the initial synthesis conditions affected the capacity and cycling performance of LiMn₂O₄ are discussed.     

Electrochemical behavior of polyamides with cyclic disulfide structure and their application to positive active material for lithium secondary battery

Polyamides (DTA-I, DTA-II, and DTA-III) containing cyclic disulfide structure were prepared by condensation between 1,2-dithiane-3,6-dicarboxylic acid (DTA) and alkyl diamine, NH₂–(CH₂)_n–NH₂ (DTA-I; n=4, DTA-II; n=6, DTA-III; n=8) and their application to positive active material for lithium secondary batteries was investigated. Cyclic voltammetry (CV) measurements under slow sweep rate (0.5 mV s⁻¹) with a carbon paste electrode containing the polyamide (DTA-I, DTA-II, or DTA-III) were performed. The results indicated that the polyamides were electroactive in the organic electrolyte solution (propylene carbonate (PC)-1,2-dimethoxyethane (DME), 1:1 by volume containing lithium salt, such as LiClO₄). The responses based on the redox of the disulfide bonds in the polyamide were observed.Test cells, Li/PC-DME (1:1. by volume) with 1 mol dm⁻³ LiClO₄/the polyamide cathode, were constructed and their performance was tested under constant current charge/discharge condition. The average capacity of the test cells with the DTA-III cathode was 64.3 Ah kg⁻¹ of cathode (135 Wh kg⁻¹ of cathode, capacity (Ah kg⁻¹) of the cathode×average cell voltage (2.10 V)). Performance of the cell with linear polyamide containing disulfide bond (–CO–(CH₂)₂–S–S–(CH₂)₂–CONH–(CH₂)₈–NH–, GTA-III) was also investigated and the average capacity was 56.8 Ah kg⁻¹ of cathode (100 Wh kg⁻¹ of cathode, capacity (Ah kg⁻¹) of the cathode×average cell voltage (1.76 V)). Cycle efficiency of the test cell with the DTA-III cathode was higher than that with the GTA-III cathode.     

Multilayered Sn–Zn–Cu alloy thin-film as negative electrodes for advanced lithium-ion batteries

Sn-based alloy compounds have been considered as possible alternatives for carbon in lithium-ion batteries and attract great attentions because of their large electrochemical capacity compared with that of carbon. In this work, a multilayered Sn–Zn/Zn/Cu alloy thin-film electrode has been prepared by electroplating method. The structure and performance of the electrode before and after heat treatment have been investigated. It is found that Cu₆Sn₅ phase and multilayered structure in electrode are formed after heat treatment. This optimized structure of the heat-treated electrode results in enhanced cycle life. The capacity of the electrode is over 320 mA h g⁻¹ after 100 cycles; though it is 83 mA h g⁻¹ after 20 cycles for as-plated electrode. The Sn–Cu and Zn–Cu alloy formed a network in the electrode is considered to strengthen the electrode and reduce the effect of volume expansion and phase transition during cycling. Experimental results also reveal that lower cut-off potential (0.05 V) for charging and higher one (1.2 V) for discharging result in long cycle life and high discharge capacity, respectively. The reason of capacity decay of the heat-treatment electrode during cycling has also been investigated. All these results show that the electroplated Sn–Zn-based alloy film on Cu foil would be a promising negative material with high capacity and low cost for Li secondary batteries.     

Preparation and electrochemical/thermal properties of LiNi0.74Co0.26O2 cathode material

Electrochemical and thermal properties of LiNi_0.74Co_0.26O₂ cathode material with 5, 13 and 25 μm-sized particles have been studied by using a coin-type half-cell Li/LiNi_0.74Co_0.26O₂. The specific capacity of the material ranges from 205 to 210 mA h g⁻¹, depending on the particle size or the Brunauer, Emmett and Teller (BET) surface area. Among the particle sizes, the cathode with a particle size of 13 μm shows the highest specific capacity. Even though the material with a particle size of 5 μm exhibits the smallest capacity value of 205 mA h g⁻¹, no capacity fading was observed after 70 cycles between 4.3 and 2.75 V at the 1 C rate. Differential scanning calorimetry (DSC) studies of the charged electrode at 4.3 V show a close relationship between particle size (BET surface area) and thermal stability of the electrode, namely, a larger particle size (smaller BET surface area) leads to a better thermal stability of the LiNi_0.74Co_0.26O₂ cathode.     

Effects of synthesis conditions on the structural and electrochemical properties of layered Li[Ni1/3Co1/3Mn1/3]O2 cathode material via the hydroxide co-precipitation method LIB SCITECH

The uniform layered Li[Ni_1/3Co_1/3Mn_1/3]O₂ cathode material for lithium ion batteries was prepared by using (Ni_1/3Co_1/3Mn_1/3)(OH)₂ synthesized by a liquid phase co-precipitation method as precursor. The effects of calcination temperature and time on the structural and electrochemical properties of the Li[Ni_1/3Co_1/3Mn_1/3]O₂ were systemically studied. XRD results revealed that the optimal prepared conditions of the layered Li[Ni_1/3Co_1/3Mn_1/3]O₂ were 850 °C for 18 h. Electrochemical measurement showed that the sample prepared under the above conditions has the highest initial discharge capacity of 162.1 mAh g⁻¹ and the smallest irreversible capacity loss of 9.2% as well as stable cycling performance at a constant current density of 16 mA g⁻¹ between 3 and 4.3 V versus Li at room temperature.     

Cu5Si–Si/C composites for lithium-ion battery anodes

Cu₅Si–Si/C composites with precursor atomic ratio of Si:Cu = 1, 2 and 4.5 have been produced by high-energy ball-milling of a mixture of copper–silicon alloy and graphite powder for anode materials of lithium-ion battery. X-ray diffraction and scanning electron microscope measurements show that Cu₅Si alloy is formed after the intensive ball milling and alloy particles along with low-crystallite Si are interspersed in graphite uniformly. Cu₅Si–Si/C composite electrodes deliver a larger reversible capacity than commercialized graphite and better cyclability than silicon. The increase of copper amount in the composites decreases reversible capacity but improves cycling performance. Cu₅Si–Si/C composite with Si:Cu = 1 demonstrates an initial reversible capacity of 612 mAh g⁻¹ at 0.2 mA cm⁻² in the voltage range from 0.02 to 1.5 V. The capacity retention is respectively 74.5 and 70.0% at the 40th cycle at the current density of 0.2 and 1 mA cm⁻².     

Synthesis and characterizations of Li[CrxLi(1−x)/3Mn2(1−x)/3]O2 (0.15 ≤ x ≤ 0.3) cathode materials in rechargeable lithium batteries

A series of Li[Cr_xLi_(1−x)/3Mn_2(1−x)/3]O₂ (0.15 ≤ x ≤ 0.3) cathode materials was prepared by citric acid-assisted, sol–gel process. Sub-micron sized particles were obtained and the X-ray diffraction (XRD) results showed that the crystal structure was similar to layered lithium transition metal oxides (R-3m space group). The electrochemical performance of the cathodes was evaluated over the voltage range 2.0–4.9 V at a current density of 7.947 mA g⁻¹. The Li_1.27Cr_0.2Mn_0.53O₂ electrode delivered a high reversible capacity of up to 280 mAh g⁻¹ during cycling. Li[Cr_xLi_(1−x)/3Mn_2(1−x)/3]O₂ yielded a promising cathode material.     

Cresol–formaldehyde based carbon aerogel as electrode material for electrochemical capacitor

Carbon aerogels have been prepared through a polycondensation of cresol (Cm) with formaldehyde (F) and an ambient pressure drying followed by carbonization at 900 °C. Modification of the porous structures of the carbon aerogel can be achieved by CO₂ activation at various temperatures (800, 850, 900 °C) for 1–3 h. This process could be considered as an alternative economic route to the classic RF gels synthesis. The obtained carbon aerogels have been attempted as electrode materials in electric double-layer capacitors. The relevant electrochemical behaviors were characterized by constant current charge–discharge experiments, cyclic voltammetry and electrochemical impedance spectroscopy in an electrolyte of 30% KOH aqueous solution. The results indicate that a mass specific capacitance of up to 78 F g⁻¹ for the non-activated aerogel can be obtained at current density 1 mA cm⁻². CO₂ activation can effectively improve the specific capacitance of the carbon aerogel. After CO₂ activation performed at 900 °C for 2 h, the specific capacitance increases to 146 F g⁻¹ at the same current. Only a slight decrease in capacitance, from 146 to 131 F g⁻¹, was observed when the current density increases from 1 to 20 mA cm⁻², indicating a stable electrochemical property of carbon aerogel electrodes in 30% KOH aqueous electrolyte with various currents.     

Photocured PEO-based solid polymer electrolyte and its application to lithium–polymer batteries

A solid polymer electrolyte (SPE) based on polyethylene oxide (PEO) is prepared by photocuring of polyethylene glycol acrylates. The conductivity is greatly enhanced by adding low molecular weight poly(ethylene glycol) dimethylether (PEGDME). The maximum conducticity is 5.1×10⁻⁴ S cm⁻¹ at 30°C. These electrolytes display oxidation stability up to 4.5 V against a lithium reference electrode. Reversible electrochemical plating/stripping of lithium is observed on a stainless steel electrode. Li/SPE/LiMn₂O₄ as well as C(Li)/SPE/LiCoO₂ cells have been fabricated and tested to demonstrate the applicability of the resulting polymer electrolytes in lithium–polymer batteries.