Numerical evaluation of a parallel fuel feeding SOFC–PEFC system using seal-less planar SOFC stack

We propose a system that combines a seal-less planar solid oxide fuel cell (SOFC) stack and polymer electrolyte fuel cell (PEFC) stack. In the proposed system, fuel for the SOFC (SOFC fuel) and fuel for the PEFC (PEFC fuel) are fed to each stack in parallel. The steam reformer for the PEFC fuel surrounds the seal-less planar SOFC stack. Combustion exhaust heat from the SOFC stack is used for reforming the PEFC fuel. We show that the electrical efficiency in the SOFC–PEFC system is 5% higher than that in a simple SOFC system using only a seal-less planar SOFC stack when the SOFC operation temperature is higher than 973 K.     

Effect of operating conditions and gas flow patterns on the system performances of IIR-SOFC fueled by methanol

Mathematical models of an indirect internal reforming solid oxide fuel cells (IIR-SOFC) fueled by methanol were developed to analyze the thermal coupling of the internal endothermic steam reforming with exothermic electrochemical reactions and predict the system performance. The simulations indicated that IIR-SOFC fueled by methanol can be well performed as autothermal operation, although slight temperature gradient occurred at the entrance of the reformer chamber. Sensitivity analysis of five important parameters (i.e. operating voltage, reforming catalyst reactivity, inlet steam to carbon ratio, operating pressure and flow direction) was then performed. The increase of operating voltage lowered the average temperature along the reformer chamber and improved the electrical efficiency, but it oppositely reduced the average current density. Greater temperature profile along the system can be obtained by applying the catalyst with lower reforming reactivity; nevertheless, the current density and electrical efficiency slightly decreased. By using high inlet steam to carbon ratio, the cooling spot at the entrance of the reformer can be reduced but both current density and electrical efficiency were decreased. Lastly, with increasing operating pressure, the system efficiency increased and the temperature dropping at the reformer chamber was minimized.     

Simulation analysis of a system combining solid oxide and polymer electrolyte fuel cells

We evaluated the performance of system combining a solid oxide fuel cell (SOFC) stack and a polymer electrolyte fuel cell (PEFC) stack by a numerical simulation. We assume that tubular-type SOFCs are used in the SOFC stack. The electrical efficiency of the SOFC–PEFC system increases with increasing oxygen utilization rate in the SOFC stack. This is because the amount of exhaust heat of the SOFC stack used to raise the temperature of air supplied to it decreases as its oxygen utilization rate increases and because that used effectively as the reaction heat of the steam reforming reaction of methane in the stack reformer increases. The electrical efficiency of the SOFC–PEFC system at 190 kW ac is 59% (LHV), which is equal to that of the SOFC-gas turbine combined system at 1014 kW ac.     

Analysis of a SOFC energy generation system fuelled with biomass reformate

Biomass reformation is an interesting path for hydrogen production and its use for efficient energy generation. The main target is the fully exploitation of the potential of renewable fuels. To this aim, the coupling a biomass reformer together with a high temperature solid oxide fuel cell (SOFC) stack shows some advantages for the similar operating temperature of the two processes and the internal reforming capability of the SOFC. The latter further allows less stringent composition requirements of the feed gas from a gasifier and internal cooling of the SOFC.In this work, a complete model of a SOFC coupled with a biomass gasifier is used to identify the main effects of the operating conditions on the fuel cell performance.The gasification process has been simulated by an equilibrium model able to compute the reformate composition under different operating conditions, whereas a 3D fluid dynamics simulation (FLUENT) coupled with an external model for the electrochemical reactions has been used to predict the fuel cell performance in terms of electrical response and mass-energy fluxes.A 14 kW integrated SOFC-gasifier system has been analysed with this model to address the response of a planar SOFC as a function of the gasifier operating conditions.     

Thermodynamic modeling of direct internal reforming solid oxide fuel cells operating with syngas

In this paper a direct internal reforming solid oxide fuel cell (DIR-SOFC) is modeled thermodynamically from the energy point of view. Syngas produced from a gasification process is selected as a fuel for the SOFC. The modeling consists of several steps. First, equilibrium gas composition at the fuel channel exit is derived in terms mass flow rate of fuel inlet, fuel utilization ratio, recirculation ratio and extents of steam reforming and water–gas shift reaction. Second, air utilization ratio is determined according to the cooling necessity of the cell. Finally, terminal voltage, power output and electrical efficiency of the cell are calculated. Then, the model is validated with experimental data taken from the literature. The methodology proposed is applied to an intermediate temperature, anode-supported planar SOFC operating with a typical gas produced from a pyrolysis process. For parametric analysis, the effects of recirculation ratio and fuel utilization ratio are investigated. The results show that recirculation ratio does not have a significant effect for low current density conditions. At higher current densities, increasing the recirculation ratio decreases the power output and electrical efficiency of the cell. The results also show that the selection of the fuel utilization ratio is very critical. High fuel utilization ratio conditions result in low power output and air utilization ratio but higher electrical efficiency of the cell.     

An internal reformer for a pressurised SOFC system

A novel reformer design has been demonstrated that converts the methane required for a multi kilowatt SOFC stack. Results show the influence of temperature and the benefits of operating at elevated pressure on the reforming-catalyst fundamental reaction kinetics. Due to the high heat demand of the steam reforming reaction, efficient heat transfer between the SOFC stack and the reforming catalyst is essential. Parameters such as the volume/surface area ratio, choice of catalyst, and catalyst metal loading are key to the design, and these have been determined through a combination of computer modelling and experimental measurements. The thermal properties of the unit have been evaluated over a range of temperatures and fuel compositions that simulate system operating-conditions in the final product.     

Performance analysis of a solid oxide fuel cell with reformed natural gas fuel

In the present study a two‐dimensional model of a tubular solid oxide fuel cell operating in a stack is presented. The model analyzes electrochemistry, momentum, heat and mass transfers inside the cell. Internal steam reforming of the reformed natural gas is considered for hydrogen production and Gibbs energy minimization method is used to calculate the fuel equilibrium species concentrations. The conservation equations for energy, mass, momentum and voltage are solved simultaneously using appropriate numerical techniques. The heat radiation between the preheater and cathode surface is incorporated into the model and local heat transfer coefficients are determined throughout the anode and cathode channels. The developed model has been compared with the experimental and numerical data available in literature. The model is used to study the effect of various operating parameters such as excess air, operating pressure and air inlet temperature and the results are discussed in detail. The results show that a more uniform temperature distribution can be achieved along the cell at higher air‐flow rates and operating pressures and the cell output voltage is enhanced. It is expected that the proposed model can be used as a design tool for SOFC stack in practical applications. Copyright © 2009 John Wiley & Sons, Ltd.     

Modelling of tubular-designed solid oxide fuel cell with indirect internal reforming operation fed by different primary fuels

Mathematical models of an indirect internal reforming solid oxide fuel cell (IIR-SOFC) fed by four different primary fuels, i.e., methane, biogas, methanol and ethanol, are developed based on steady-state, heterogeneous, two-dimensional and tubular-design SOFC models. The effect of fuel type on the thermal coupling between internal endothermic reforming with exothermic electrochemical reactions and system performance are determined. The simulation reveals that an IIR-SOFC fuelled by methanol provides the smoothest temperature gradient with high electrochemical efficiency. Furthermore, the content of CO₂ in biogas plays an important role on system performance since electrical efficiency is improved by the removal of some CO₂ from biogas but a larger temperature gradient is expected.Sensitivity analysis of three parameters, namely, a operating pressure, inlet steam to carbon (S:C) ratio and flow direction is then performed. By increasing the operating pressure up to 10 bar, the system efficiency increases and the temperature gradient can be minimized. The use of a high inlet S:C ratio reduces the cooling spot at the entrance of reformer channel but the electrical efficiency is considerably decreased. An IIR-SOFC with a counter-flow pattern (as based case) is compared with that with co-flow pattern (co-flow of air and fuel streams through fuel cell). The IIR-SOFC with co-flow pattern provides higher voltage and a smoother temperature gradient along the system due to superior matching between heat supplied from electrochemical reaction and heat required for steam reforming reaction; thus it is expected to be a better option for practical applications.     

Thermodynamic model and parametric analysis of a tubular SOFC module

Solid oxide fuel cells (SOFCs) have been considered in the last years as one of the most promising technologies for very high-efficiency electric energy generation from natural gas, both with simple fuel cell plants and with integrated gas turbine-fuel cell systems. Among the SOFC technologies, tubular SOFC stacks with internal reforming have emerged as one of the most mature technology, with a serious potential for a future commercialization. In this paper, a thermodynamic model of a tubular SOFC stack, with natural gas feeding, internal reforming of hydrocarbons and internal air preheating is proposed. In the first section of the paper, the model is discussed in detail, analyzing its calculating equations and tracing its logical steps; the model is then calibrated on the available data for a recently demonstrated tubular SOFC prototype plant. In the second section of the paper, it is carried out a detailed parametric analysis of the stack working conditions, as a function of the main operating parameters. The discussion of the results of the thermodynamic and parametric analysis yields interesting considerations about partial load SOFC operation and load regulation, and about system design and integration with gas turbine cycles.     

Performance analysis of a tubular solid oxide fuel cell with an indirect internal reformer

A 2‐D steady‐state mathematical model of a tubular solid oxide fuel cell with indirect internal reforming (IIR‐SOFC) has been developed to examine the chemical and electrochemical processes and the effect of different operating parameters on the cell performance. The conservation equations for energy, mass, momentum as well as the electrochemical equations are solved simultaneously employing numerical techniques. A co‐flow configuration is considered for gas streams in the air and fuel channels. The heat radiation between the preheater and reformer surface is incorporated into the model and local heat transfer coefficients are determined throughout the channels. The model predictions have been compared with the data available in the literature. The model was used to study the effect of various operating conditions on the cell performance. Numerical results indicate that as the cell operating pressure increases, the reforming reaction extends to a larger portion of the cell and the maximum temperature move away from the cell inlet. As a result, a more uniform temperature prevails in the solid structure which reduces thermal stresses. Also, at higher excess air, the rate of heat transfer to the air stream is augmented and the average cell temperature is decreased. Copyright © 2010 John Wiley & Sons, Ltd.     

Thermal start-up behaviour and thermal management of SOFC's

Solid oxide fuel cells (SOFCs) have many attractive features for widespread applications. The high operating temperature provides a valuable heat source and in contrast to low temperature fuel cells they not only tolerate substances such as CO but can even use them as fuel. Thus, reforming of hydrocarbon fuels for SOFCs can be done without additional gas purification. As both stack and hydrocarbon reformer unit have to be operated at high temperatures (700–1000 °C), thermal management plays an important role in the successful operation of SOFC systems. As the SOFC system contains ceramic components, both large thermal gradients in the system and thermal expansion coefficient (TEC) mismatch must be avoided.Matching TECs is done by selecting the suitable materials. Avoiding high temperature gradients is done by selecting the right system design and control strategies. In order to achieve both, we have built a finite element simulation for a complete SOFC systems which allows to study system parameters both during steady operation and during transients. Examples of the thermal start-up behaviour for several system configurations are given for selected components as well as internal temperatures of the SOFC-stack during start-up. The simulation model includes also the option to simulate the effects of internal methane reformation in the SOFC stack.As the minimum operation temperature is high, cooling down of the system has to be avoided if instant operation is desired. This can be achieved either passively by selecting suitable thermal insulation materials and/or actively by adopting a strategy for maintaining the temperature.     

Comparison and optimization of different fuel processing options for biogas-fed solid-oxide fuel cell plants

The biogas needs to be reformed before electro-chemical conversion in the solid-oxide fuel cell, which can be promoted efficiently with wise thermal management and reforming conditions. To ensure the system safety and catalysts durability, additional mineral-bearing water and carbon deposition should be avoided. This paper conducted a detailed biogas-SOFC CHP system analysis considering four layouts, featuring hot and cold recirculation of the anode off-gas, partial oxidation and complete internal reforming. The process optimization and sensitivity analysis are performed with the design variables including the recirculation ratio, and external reformer temperature. The anode supported SOFC operates at 800 °C and 0.4 A/cm² current density. The results show that pre-reforming with hot recirculation and cold recirculation schemes achieve the highest system efficiency between 56% and 63%. The pre-reforming with hot recirculation scheme has a broader self-sufficient water range eliminating the carbon deposition risk at the recirculation ratio of 42–78% and reforming temperature of 400–650 °C. The no pre-reforming with hot recirculation scheme achieves maximum system efficiency of 58% due to the fuel dilution. Moreover, the partial oxidation with hot recirculation scheme maximum efficiency is limited to 58.9%, given that the partial oxidation reaction is less efficient than steam and dry reforming reactions. The proposed system layout could demonstrate the feasibility of biogas-SOFC with different reforming options especially on small scale with high efficiency and optimal thermal integration opportunities.     

Design performance analysis of pressurized solid oxide fuel cell/gas turbine hybrid systems considering temperature constraints

This study presents critical aspects and their influence on the performance of hybrid power systems combining a pressurized solid oxide fuel cell (SOFC) and a gas turbine (GT). Two types of hybrid system configurations with internal and external reforming have been analyzed. In order to examine the effect of matching between the fuel cell temperature and the turbine inlet temperature on the hybrid system performance, we considered air bypass after the compressor as well as additional fuel supply to the turbine side. This study focuses on the limitation of the temperature difference at the fuel cell stack and its influence on the performances of the two hybrid systems. Performances of the hybrid systems are also compared with those of simple SOFC systems, and the extent of performance enhancement is evaluated. The system with internal reforming gives better efficiency and power capacity for all design conditions than the system with external reforming under the same constraints. Its efficiency gain over the SOFC only system is considerable, while that of the system with external reforming is far less. As the temperature difference at the cell becomes smaller, the system performance generally degrades. The system with internal reforming is less influenced by the constraint of the cell temperature difference.     

Investigation on performance of an integrated solid oxide fuel cell and absorption chiller tri-generation system

An integrated tri-generation system incorporating a solid oxide fuel cell (SOFC) and a double-effect water/Lithium Bromide absorption chiller is presented in this paper. The proposed tri-generation system can provide power, cooling or heating simultaneously with a typical gas produced from a gasication process. The system conguration and design are discussed, and the energy and mass balances are obtained through the matrix representation method and integrated into a simulation program by MATLAB soft package. The developed model comprises of three modules: SOFC module, exhaust combusting and HRSG module, and the absorption chiller module. Validation of the SOFC model is performed by comparison with a single tubular cell of Siemens-Westinghouse, and a specific case study of the system is presented. For parametric analysis, the fuel utilization ratio, fuel flow ratio and air inlet temperature are investigated and the results are discussed in detail.     

Development of a fuel feeder for a solid oxide fuel cell test station

Solid oxide fuel cells (SOFC) can utilize various fuels, such as natural gas, hydrogen and biogas, but often, it is sensible to use a pre‐reformer that converts the fuel into a hydrogen‐rich gas stream. Relevant testing conditions, including the fuel to be used in SOFC systems, are important because cell performance depends on test conditions, such as fuel composition. Still, a majority of the reported single‐cell and short stack tests are performed with pure hydrogen or synthetic reformate mixed from gas bottles. In this article, the development of a fuel feeder used to pre‐reform natural gas for a single cell SOFC test station is presented. To mimic SOFC system conditions, natural gas is taken from the grid, desulfurized with commercial sulfur sorbent and reformed with a commercial precious metal catalyst. The fuel feeder is designed to be a versatile and efficient research tool, capable to be used in a wide temperature and gas flow range and with different reforming techniques, such as steam reforming, catalytic partial oxidation and simulated anode off‐gas recycling. The construction, operation and characterization of the fuel feeder as well as methods of avoiding carbon formation are discussed. The performance is evaluated by comparing measured outlet temperatures and compositions against equilibrium values. All measured gas compositions matched closely with the calculated equilibrium values, and the identified deviations were small and to no harm in practical use. The operator can control the product gas composition by setting the fuel feeder heater to the temperature corresponding to the targeted composition. Results show that the fuel feeder design can be used as such for single‐cell testing or scaled to fit larger stack test stations. Copyright © 2015 John Wiley & Sons, Ltd.     

Externally reformed solid oxide fuel cell–micro-gas turbine (SOFC–MGT) hybrid systems fueled by methanol and di-methyl-ether (DME)

Solid oxide fuel cell–micro-gas turbine (SOFC–MGT) hybrid power plants integrate a solid oxide fuel cell and a micro-gas turbine and can achieve efficiencies of over 60% even for small power outputs (200–500 kW). The SOFC–MGT systems currently developed are fueled with natural gas, which is reformed inside the same stack, but the use of alternative fuels can be an interesting option. In particular, as the reforming temperature of methanol and di-methyl-ether (DME) (200–350 °C) is significantly lower than that of natural gas (700–900 °C), the reformer can be sited outside the stack. External reforming in SOFC–MGT plants fueled by methanol and DME enhances efficiency due to improved exhaust heat recovery and higher voltage produced by the greater hydrogen partial pressure at the anode inlet. The study carried out in this paper shows that the main operating parameters of the fuel reforming section (temperature and steam-to-carbon ratio (SCR)) must be carefully chosen to optimise the hybrid plant performance. For the stoichiometric SCR values, the optimum reforming temperature for the methanol fueled hybrid plant is approximately 240 °C, giving efficiencies of about 67–68% with a SOFC temperature of 900 °C (the efficiency is about 72–73% at 1000 °C). Similarly, for DME the optimum reforming temperature is approximately 280 °C with efficiencies of 65% at 900 °C (69% at 1000 °C). Higher SCRs impair stack performance. As too small SCRs can lead to carbon formation, practical SCR values are around one for methanol and 1.5–2 for DME.     

Mini CHP based on the electrochemical generator and impeded fluidized bed reactor for methane steam reforming

The paper presents a configuration of mini CHP with the methane reformer and planar solid oxide fuel cell (SOFC) stacks. This mini CHP may produce electricity and superheated steam as well as preheat air and methane for the reformer along with cathode air used in the SOFC stack as an oxidant. Moreover, the mathematical model for this power plant has been created. The thermochemical reactor with impeded fluidized bed for autothermal steam reforming of methane (reformer) considered as the basis for the synthesis gas (syngas) production to fuel SOFC stacks has been studied experimentally as well. A fraction of conversion products has been oxidized by the air fed to the upper region of the impeded fluidized bed in order to carry out the endothermic methane steam reforming in a 1:3 ratio as well as to preheat products of these reactions. Studies have shown that syngas containing 55% of hydrogen could be produced by this reactor. Basic dimensions of the reactor as well as flow rates of air, water and methane for the conversion of methane have been adjusted through mathematical modelling.The paper provides heat balances for the reformer, SOFC stack and waste heat boiler (WHB) intended for generating superheated water steam along with preheating air and methane for the reformer as well as the preheated cathode air. The balances have formed the basis for calculating the following values: the useful product fraction in the reformer; fraction of hydrogen oxidized at SOFC anode; gross electric efficiency; anode temperature; exothermic effect of syngas hydrogen oxidation by air oxygen; excess entropy along with the Gibbs free energy change at standard conditions; electromotive force (EMF) of the fuel cell; specific flow rate of the equivalent fuel for producing electric and heat energy. Calculations have shown that the temperature of hydrogen oxidation products at SOFC anode is 850 °C; gross electric efficiency is 61.0%; EMF of one fuel cell is 0.985 V; fraction of hydrogen oxidized at SOFC anode is 64.6%; specific flow rate of the equivalent fuel for producing electric energy is 0.16 kg of eq.f./(kW·h) while that for heat generation amounts to 44.7 kg of eq.f./(GJ). All specific parameters are in agreement with the results of other studies.     

Performance characteristics of a robust and compact propane-fueled 150 W-class SOFC power-generation system

A propane-fueled solid-oxide fuel-cell-based system is an extraordinary type of technology for stationary mobile power generation given that it offers higher efficiency, silent operation and clean conversion of hydrocarbon fuels. In this study, we designed and developed a 150 W-class tubular SOFC power-generation system integrated with a catalytic partial reformer (CPOX) for the propane fuel and heat exchangers with the goal of making a robust and compact system for portable power applications. Micro-tubular SOFC cells were fabricated by ceramic processing and the cells were assembled in the form of a short stack. The CPOX nano-catalyst CeO₂Zr₂O₃/Pt supported on γ-Al₂O₃ was prepared and tested for its propane-reforming characteristics under the present operating conditions. The CPOX catalyst was used in the integrated reformer, and the performance of the 150 W-class SOFC power-generation system operating on propane fuel was studied. The rapid startup and temperature sustainability of the short stack were also monitored and stable stack temperatures were achieved within 20 min. Long-term galvanostatic operation of the power-generation system was also conducted to investigate the durability of the system. This study confirms that propane-fueled robust and compact 150 W-class power-generation systems are suitable for portable applications and that the role of efficient CPOX catalysts is crucial for high performance of the stack when operating on propane fuel.     

Performance analysis of a SOFC under direct internal reforming conditions

This paper presents the performance analysis of a planar solid-oxide fuel cell (SOFC) under direct internal reforming conditions. A detailed solid-oxide fuel cell model is used to study the influences of various operating parameters on cell performance. Significant differences in efficiency and power density are observed for isothermal and adiabatic operational regimes. The influence of air number, specific catalyst area, anode thickness, steam to carbon (s/c) ratio of the inlet fuel, and extend of pre-reforming on cell performance is analyzed. In all cases except for the case of pre-reformed fuel, adiabatic operation results in lower performance compared to isothermal operation. It is further discussed that, though direct internal reforming may lead to cost reduction and increased efficiency by effective utilization of waste heat, the efficiency of the fuel cell itself is higher for pre-reformed fuel compared to non-reformed fuel. Furthermore, criteria for the choice of optimal operating conditions for cell stacks operating under direct internal reforming conditions are discussed.     

Operational characteristics of a planar steam reformer thermally coupled with a catalytic burner

High efficiency reforming is a key parameter of high temperature stationary fuel cell systems. In this study, a planar heat exchanger steam reformer (PHESR) was integrated with a catalytic combustor in order that the unused energy of the anode off-gas is delivered for heating and reforming. The PHESR was designed to use the anode off-gas of the externally reformed SOFC system because it has an efficiency problem. In the PHESR reactor, the heat is transferred from the catalytic burner to the reformer that has the smallest gradient of temperature difference between the two reactors.