The effect of Al(OH)3 coating on the Li[Li0.2Ni0.2Mn0.6]O2 cathode material for lithium secondary battery

Layered Li[Li_0.2Ni_0.2Mn_0.6]O₂ powder was modified by coating its surface with amorphous Al(OH)₃. Energy dispersive spectroscopy (EDS) showed that nano-sized Al(OH)₃ powders were homogeneously dispersed in the parent Li[Li_0.2Ni_0.2Mn_0.6]O₂ powders. Al(OH)₃ coated Li[Li_0.2Ni_0.2Mn_0.6]O₂ exhibited an greater retention capacity at higher rates compared to uncoated Li[Li_0.2Ni_0.2Mn_0.6]O₂. The low area specific impedance (ASI) value of the Al(OH)₃ is the major factor for its higher rate performance. The 1.4 wt.% Al(OH)₃ coated sample had an impedance of 41 Ω cm² while uncoated Li[Li_0.2Ni_0.2Mn_0.6]O₂ had a 57 Ω cm² at 30-80% state of charge. Electrochemical impedance spectroscopy (EIS) also showed that the Al(OH)₃ coated sample had a lower charge transfer resistance (R_ct) than the uncoated sample. Differential scanning calorimetry (DSC) analysis showed that Al(OH)₃ coating improved the thermal stability. Al(OH)₃ coating increased the onset temperature of thermal decomposition and reduced the amount of heat for the exothermic peak.     

X-ray photoelectron spectroscopy and electrochemical behaviour of 4 V cathode, Li(Ni1/2Mn1/2)O2

Layered Li(Ni_1/2Mn_1/2)O₂ was prepared by the solution and mixed hydroxide methods, characterised by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) and studied by cyclic voltammetry (CV) and charge discharge cycling in CC and CCCV modes at room temperature (r.t.) and at 50 °C. The XPS studies show about 8% of Ni³⁺ and Mn³⁺ ions are present in Li(Ni²⁺_1/2Mn_1/2⁴⁺)O₂ due to valency-degeneracy. The compound prepared at 950 °C, 12 h, solution method gives a second cycle discharge capacity of 150 mA h g⁻¹ (2.5-4.4 V) at a specific current of 30 mA g⁻¹ and retains 137 mA h g⁻¹ at the end of 40 cycles. CV shows that the redox process at 3.7-4.0 V corresponds to Ni²⁺↔Ni⁴⁺ and clear indication of Mn^3+/4+ couple was noted at 4.2-4.5 V. The observed capacity-fading (2.5-4.4 V) is shown to be contributed by the polarisation at the end of charging. The cathodic capacity is stable up to 40 cycles in the voltage window, 2.5-4.2 V both at room temperature and 50 °C.     

Heat-treated metal phthalocyanine complex as an oxygen reduction catalyst for non-aqueous electrolyte Li/air batteries

In this work we study heat-treated FeCu-phthalocyanine (FeCuPc) complexes as the catalyst for oxygen reduction in non-aqueous electrolyte Li/air cells by supporting the catalyst on a high surface area Ketjenblack EC-600JD carbon black. It is shown that the resultant FeCu/C catalyst not only accelerates the two-electron reduction of oxygen as “O₂ + 2Li⁺ + 2e → Li₂O₂”, but also catalyzes the chemical disproportionation of Li₂O₂ as “2Li₂O₂ → 2Li₂O + O₂”. In Li/air cells, the catalyst reduces polarization on discharge while simultaneously reducing the fraction of Li₂O₂ in the final discharged products. In a 0.2 mol kg⁻¹ LiSO₃CF₃ 7:3 (wt.) propylene carbonate (PC)/tris(2,2,2-trifluoroethyl) phosphate (TFP) electrolyte, the Li/air cells with FeCu/C show at least 0.2 V higher discharge voltage at 0.2 mA cm⁻² than those with pristine carbon. By measuring the charge-transfer resistance (R_ct) of Li/air cells at temperatures ranging between −30 °C and 30 °C, we determine the apparent activation energy of the discharge of Li/air cells and discuss the effect of FeCu/C catalyst on the oxygen reduction in Li/air cells.     

Synthetic optimization of spherical Li[Ni1/3Mn1/3Co1/3]O2 prepared by a carbonate co-precipitation method

A carbonate co-precipitation method was employed to prepare spherical Li[Ni_1/3Co_1/3Mn_1/3]O₂ cathode material. The precursor, [Ni_1/3Co_1/3Mn_1/3]CO₃, was prepared using ammonia as chelating agent under CO₂ atmosphere. The spherical Li[Ni_1/3Co_1/3Mn_1/3]O₂ was prepared by mixing the precalcined [Ni_1/3Co_1/3Mn_1/3]CO₃ with LiOH followed by high temperature calcination. The preparation conditions such as ammonia concentration, co-precipitation temperature, calcination temperature and Li/[Ni_1/3Co_1/3Mn_1/3] ratio were varied to optimize the physical and electrochemical properties of the prepared Li[Ni_1/3Co_1/3Mn_1/3]O₂. The structural, morphological, and electrochemical properties of the prepared LiNi_1/3Co_1/3Mn_1/3O₂ were characterized by XRD, SEM, and galvanostatic charge-discharge cycling. The optimized material has a spherical particle shape and a well ordered layered structure, and it also has an initial discharge capacity of 162.7 mAh g^− 1 in a voltage range of 2.8-4.3 V and a capacity retention of 94.8% after a hundred cycles. The optimized ammonia concentration, co-precipitation temperature, calcination temperature, and Li/[Ni_1/3Co_1/3Mn_1/3] ratio are 0.3 mol L^− 1, 60 °C, 850 °C, and 1.10, respectively.     

Electrochemical properties of TiP2O7 and LiTi2(PO4)3 as anode material for lithium ion battery with aqueous solution electrolyte

Some polyanionic compounds, e.g. TiP₂O₇ and LiTi₂(PO₄)₃ with 3D framework structure were proposed to be used as anodes of lithium ion battery with aqueous electrolyte. The cyclic voltammetry properties TiP₂O₇ and LiTi₂(PO₄)₃ suggested that Li-ion de/intercalation reaction can occur without serious hydrogen evolution in 5 M LiNO₃ aqueous solution. The TiP₂O₇ and LiTi₂(PO₄)₃ give capacities of about 80 mAh/g between potentials of −0.50 V and 0 V (versus SHE) and 90 mAh/g between −0.65 V and −0.10 V (versus SHE), respectively. A test cell consisting of TiP₂O₇/5 M LiNO₃/LiMn₂O₄ delivers approximately 42 mAh/g (weight of cathode and anode) at average voltage of 1.40 V, and LiTi₂(PO₄)₃/5 M LiNO₃/LiMn₂O₄ delivers approximately 45 mAh/g at average voltage of 1.50 V. Both as-assembled cells suffered from short cycle life. The capacity fading may be related to deterioration of anode material.     

The synthesis of Li(Ni1/3Co1/3Mn1/3)O2 using eutectic mixed lithium salt LiNO3–LiOH

A lithium-ion battery cathode material, Li(Ni_1/3Co_1/3Mn_1/3)O₂, with excellent electrochemical properties was prepared via two-step isothermal sintering, using eutectic lithium salts (0.38LiOH·H₂O–0.62LiNO₃) mixed with Co, Ni, or Mn hydroxides. Based on analysis using X-ray diffraction (XRD), scanning electron microscopy (SEM), a thermogravimetric-differential scanning calorimetric (TG–DSC) analyzer, and Fourier-transform Infrared (FT-IR), this synthetic process consists of procedures including lithium salt melting, permeation, reaction, crystalline transformation, and crystallization. Due to the lower melting point of the eutectic molten salts compared with that of the single lithium salt, a relatively mild synthetic condition (low temperature) is needed, and the product can be highly crystallized with low cation mixing, which facilitates maintenance of the precursor morphology. The electrochemical properties of the product were investigated by constant current discharge–charge and cyclic voltammetry. The results show that the initial discharge capacity is 160 mhA g⁻¹, with excellent cycling stability even after 50 cycles. We conclude that this novel eutectic molten salt method is a promising and practical approach for synthesizing cathode materials for lithium-ion batteries.     

Sulfur–carbon composite electrode for all-solid-state Li/S battery with Li2S–P2S5 solid electrolyte

All-solid-state Li/S batteries with Li₂S–P₂S₅ glass–ceramic electrolytes were fabricated and their electrochemical performance was examined. Sulfur–carbon composite electrodes were prepared by grinding with a mortar and milling with a planetary ball-mill apparatus. Milling of a mixture of sulfur, acetylene black and the Li₂S–P₂S₅ glass–ceramic electrolyte resulted in the amorphization of sulfur and a reduction in the particle size of the mixture. The charge–discharge properties of all-solid-state cells with the composite electrode were investigated at temperatures from −20 °C to 80 °C. The cells retained a reversible capacity higher than 850 mAh g⁻¹ for 200 cycles under 1.3 mA cm⁻² (333 mA g⁻¹) at 25 °C. The cell performance was influenced by the crystallinity of sulfur and the particle size of the electrode material, whereby improved contact among the electrode components achieved by milling contributed to enhancement of the capacity of an all-solid-state Li/S cell.     

One-step synthesis and improved electrochemical performance of Li(Ni1/3Co1/3Mn1/3)O2 by a modified radiated polymer gel method

We present the mechanism for the synthesis of a layered Li(Ni_1/3Co_1/3Mn_1/3)O₂ compound by a modified radiated gel method. Pure-phase Li(Ni_1/3Co_1/3Mn_1/3)O₂ material was achieved when the polymer gel was calcined at 900 °C between 15 and 30 h. The unit cell parameter c decreased, and a varied slightly with increased sintering time. Electrochemical characterization revealed that the optimized sample (25 h) had a high initial discharge capacity of 188 mAh/g (2.8-4.5 V, 20 mA/g), an excellent capacity retention of 90.1% after 30 cycles and a good rate performance.     

Hydrothermal synthesis of Li(Ni1/3Co1/3Mn1/3)O2 for lithium rechargeable batteries

Ultrafine powders of Li(Ni_1/3Co_1/3Mn_1/3)O₂ cathode materials for lithium-ion secondary batteries were prepared under mild hydrothermal conditions. The influence of the molar ratio of Li/(Ni + Co + Mn) was studied. The products were investigated by XRD, TEM and EDS. The final products were found to be well crystallized Li(Ni_1/3Co_1/3Mn_1/3)O₂ with an average particle size of about 10 nm.     

Effect of synthesis condition on the structure and electrochemical properties of Li[Ni1/3Mn1/3Co1/3]O2 prepared by hydroxide co-precipitation method

The layered Li[Ni_1/3Co_1/3Mn_1/3]O₂ powder with good crystalline and spherical shape was prepared by hydroxide co-precipitation method. The effects of pH value, NH₄OH amount, calcination temperature and extra Li amount on the morphology, structure and electrochemical properties of the cathode material were investigated in detail. SEM results indicate that pH value affected both the morphology and the property of the cathode material, and the highest discharge capacity in the first cycle of 163 mAh g⁻¹ (2.8-4.3 V) was obtained at pH value was 12. On the contrary, the NH₄OH amount, which was used as a chelating agent, only affected the particle size distribution of the material. The calcination temperatures caused great difference in the structure and property of layered Li[Ni_1/3Co_1/3Mn_1/3]O₂, and the best electrochemical properties were obtained at the calcination temperature of 800 °C. Extra Li amount not only caused difference in the material structure, but also affected their electrochemical properties. With increasing Li amount, the lattice parameters (a and c) increased monotonously, and the highest first cycle coulombic efficiency (the ratio of discharge capacity to charge capacity in the first cycle) was obtained with the Li/M of 1.10. Therefore, the optimum synthetic conditions for the hydroxide co-precipitation reaction were: pH value was 12, NH₄OH amount was 0.36 mol L⁻¹, calcination temperature was 800 °C and the Li/M molar ratio was 1.10.     

Effect of fluorine in the preparation of Li(Ni1/3Co1/3Mn1/3)O2 via hydroxide co-precipitation

Uniform and spherical Li(Ni_1/3Co_1/3Mn_1/3)O_(2−δ)F_δ powders were synthesized via NH₃ and F⁻ coordination hydroxide co-precipitation. The effect of F⁻ coordination agent on the morphology, structure and electrochemical properties of the Li(Ni_1/3Co_1/3Mn_1/3)O_(2−δ)F_δ were studied. The morphology, size, and distribution of (Ni_1/3Co_1/3Mn_1/3)(OH)_(2−δ)F_δ particle diameter were improved in a shorter reaction time through the addition of F⁻. The study suggested that the added F improves the layered characteristics of the lattice and the cyclic performance of Li(Ni_1/3Co_1/3Mn_1/3)O₂ in the voltage range of 2.8-4.6 V. The initial capacity of the Li(Ni_1/3Co_1/3Mn_1/3)O_1.96F_0.04 was 178 mAh g⁻¹, the maximum capacity was 186 mAh g⁻¹ and the capacity after 50 cycles was 179 mAh g⁻¹ in the voltage range of 2.8-4.6 V.     

Properties of char particles obtained under O2/N2 and O2/CO2 combustion environments

Pulverized coal combustion in O₂/N₂ and O₂/CO₂ environments was investigated with a drop tube furnace. Results present that the reaction rate and burn-out degree of O₂/CO₂ chars (obtained in O₂/CO₂ environments) are lower than that of O₂/N₂ chars (obtained in O₂/N₂ environments) under the same experimental condition. It indicates that a higher O₂ concentration in O₂/CO₂ environment is needed to achieve the similar combustion characteristic to that in O₂/N₂ environment. The main differences between O₂/N₂ and O₂/CO₂ chars rely on the pore structure determined by N₂ adsorption and chemical structure measured by FT-IR. For O₂/CO₂ char, the surface is thick and the pores are compact which contribute to the fragmentation reduction of particles burning in O₂/CO₂ environment. The organic functional group elimination rate from the surface of O₂/CO₂ chars is slower or delayed. The present research results might have important implications for further understanding the intrinsic kinetics of pulverized coal combustion in O₂/CO₂ environment.     

The first cycle characteristics of Li[Ni1/3Co1/3Mn1/3]O2 charged up to 4.7 V

In this research, we studied the first cycle characteristics of Li[Ni_1/3Co_1/3Mn_1/3]O₂ charged up to 4.7 V. Properties, such as valence state of the transition metals and crystallographic features, were analyzed by X-ray absorption spectroscopy and X-ray and neutron diffractions. Especially, two plateaus observed around 3.75 and 4.54 V were investigated by ex situ X-ray absorption spectroscopy. XANES studies showed that the oxidation states of transition metals in Li[Ni_1/3Co_1/3Mn_1/3]O₂ are mostly Ni²⁺, Co³⁺ and Mn⁴⁺. Based on neutron diffraction Rietveld analysis, there is about 6% of all nickel divalent (Ni²⁺) ions mixed with lithium ions (cation mixing). Meanwhile, it was found that the oxidation reaction of Ni²⁺/Ni⁴⁺ is related to the lower plateau around 3.75 V, but that of Co³⁺/Co⁴⁺ seems to occur entire range of x in Li_1−x[Ni_1/3Co_1/3Mn_1/3]O₂. Small volume change during cycling was attributed to the opposite variation of lattice parameter “c” and “a” with charging-discharging.     

Characterization of high tap density Li[Ni1/3Co1/3Mn1/3]O2 cathode material synthesized via hydroxide co-precipitation

Li[Ni_1/3Co_1/3Mn_1/3]O₂ cathode material for lithium ion batteries was prepared by mixing metal hydroxide, (Ni_1/3Co_1/3Mn_1/3)(OH)₂, with 6% excess LiOH followed by calcinations. The (Ni_1/3Co_1/3Mn_1/3)(OH)₂ with secondary particle of about 12 μm was prepared by hydroxide co-precipitation. The tap density of the obtained Li[Ni_1/3Co_1/3Mn_1/3]O₂ powder was 2.56 ± 0.21 g cm⁻³. The powder was characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), particle size distribution (PSD) and galvanostatic charge-discharge cycling. The XRD pattern of Li[Ni_1/3Co_1/3Mn_1/3]O₂ revealed a well ordered hexagonal layered structure with low cation mixing. Secondary particles with size of 13-14 μm and primary particles with size of about 1 μm can be identified from the SEM observations. In the voltage range of 2.8-4.3 V, the initial discharge capacity of the Li[Ni_1/3Co_1/3Mn_1/3]O₂ electrode was 166.6 mAh g⁻¹, and 96.5% of the initial capacity was retained after 50 charge-discharge cycling.     

Particle size effect of Li[Ni0.5Mn0.5]O2 prepared by co-precipitation

Spherical (Ni_0.5Mn_0.5)(OH)₂ with different secondary particle size (3 μm, 10 μm in diameter) was synthesized by co-precipitation method. Mixture of the prepared hydroxide and lithium hydroxide was calcined at 950 °C for 20 h in air. X-ray diffraction patterns revealed that the prepared material had a typical layered structure with space group. Spherical morphologies with mono-dispersed powders were observed by scanning electron microscopy. It was found that the layered Li[Ni_0.5Mn_0.5]O₂ delivered an initial discharge capacity of 148 mAh g⁻¹ (3.0-4.3 V) though the particle sizes were different. Li[Ni_0.5Mn_0.5]O₂ having smaller particle size (3 μm) showed improved area specific impedance due to the reduced Li⁺ diffusion path, compared with that of Li[Ni_0.5Mn_0.5]O₂ possessing larger particle size (10 μm). Although the Li[Ni_0.5Mn_0.5]O₂ (3 μm) was electrochemically delithiated to Li_0.39[Ni_0.5Mn_0.5]O₂, the resulting exothermic onset temperature was around 295 °C, of which the value is significantly higher than that of highly delithiated Li_1−δCoO₂ (∼180 °C).     

A study on electrochemical characteristics of LiCoO2/LiNi1/3Mn1/3Co1/3O2 mixed cathode for Li secondary battery

In this study, the LiCoO₂/LiNi_1/3Mn_1/3Co_1/3O₂ mixed cathode electrodes were prepared and their electrochemical performances were measured in a high cut-off voltage. As the contents of LiNi_1/3Mn_1/3Co_1/3O₂ in the mixed cathode increases, the reversible specific capacity and cycleability of the electrode enhanced, but the rate capability deteriorated. On the contrary, the rate capability of the cathode enhanced but the reversible specific capacity and cycleability deteriorated, according to increasing the contents of LiCoO₂ in the mixed cathode. The cell of LiCoO₂/LiNi_1/3Mn_1/3Co_1/3O₂ (50:50, wt.%) mixed cathode delivers a discharge capacity of ca. 168 mAh/g at a 0.2 C rate. The capacity of the cell decreased with the current rate and a useful capacity of ca. 152 mAh/g was obtained at a 2.0 C rate. However, the cell shows very stable cycleability: the discharge capacity of the cell after 20th charge/discharge cycling maintains ca. 163 mAh/g.     

Comparative study of Li(Li1/3Ti5/3)O4 and Li(Ni1/2−xLi2x/3Tix/3)Ti3/2O4 (x = 1/3) anodes for Li rechargeable batteries

A solid solution of spinel (2/3)Li(Li_1/3Ti_5/3)O₄–(1/3)Li(Ni_1/2Ti_3/2)O₄ was prepared, and its structural/electrochemical properties were compared with Li(Li_1/3Ti_5/3)O₄ to identify the effect of doping to the structural invariance of Li(Li_1/3Ti_5/3)O₄. The solid solution retained the zero strain characteristic of Li(Li_1/3Ti_5/3)O₄ during discharge/charge with an excellent cycle stability, while the rate capability was notably improved. However, a reversible broadening of the XRD peak was observed at the end of discharge, indicating some structural changes. XANES measurements showed that the oxidation state of Ti was +4 and that of Ni was +2 in the solid solution.     

Effect of synthesis condition on the structural and electrochemical properties of Li[Ni1/3Mn1/3Co1/3]O2 prepared by the metal acetates decomposition method

In order to get homogeneous layered oxide Li[Ni_1/3Mn_1/3Co_1/3]O₂ as a lithium insertion positive electrode material, we applied the metal acetates decomposition method. The oxide compounds were calcined at various temperatures, which results in greater difference in morphological (shape, particle size and specific surface area) and the electrochemical (first charge profile, reversible capacity and rate capability) differences. The Li[Ni_1/3Mn_1/3Co_1/3]O₂ powders were characterized by means of X-ray diffraction (XRD), charge/discharge cycling, cyclic voltammetry and SEM. XRD experiment revealed that the layered Li[Ni_1/3Mn_1/3Co_1/3]O₂ material can be best synthesized at temperature of 800 °C. In that synthesized temperature, the sample showed high discharge capacity of 190 mAh g⁻¹ as well as stable cycling performance at a current density of 0.2 mA cm⁻² in the voltage range 2.3-4.6 V. The reversible capacity after 100 cycles is more than 190 mAh g⁻¹ at room temperature.     

Fabrication of all-solid-state battery using Li5La3Ta2O12 ceramic electrolyte

The chemical and electrochemical properties of Li₅La₃Ta₂O₁₂ (LLTa) solid electrolyte were extensively investigated to determine its compatibility with an all-solid-state battery. A well-sintered LLTa pellet with a garnet-like structure was obtained after sintering at 1200 °C for 24 h. Li ion conductivity of the LLTa pellet was estimated to be 1.3×10⁻⁴ S cm⁻¹. The LLTa pellet was stable when in contact with lithium metal. This indicates that Li metal anode, which is the best anode material, can be applied with the LLTa system. A full cell composed of LiCoO₂/LLTa/Li configuration was constructed, and its electrochemical properties were tested. In the resulting cyclic voltammogram, a clear redox couple of LiCoO₂ was observed, implying that the all-solid-state battery with the Li metal anode was successfully operated at room temperature. The redox peaks of the battery were still observed even after one year of storage in an Ar-filled glove-box. It can be concluded that the LLTa electrolyte is a promising candidate for the all-solid-state battery because of its relatively high Li ion conductivity and good stability when in contact with Li metal anode and LiCoO₂ cathode.     

A comparison of preparation method on the electrochemical performance of cathode material Li[Li0.2Mn0.54Ni0.13Co0.13]O2 for lithium ion battery

Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ as a cathode material for Li-ion battery has been successfully prepared by co-precipitation (CP), sol–gel (SG) and sucrose combustion (SC) methods. The prepared materials were characterized by XRD, SEM, BET and electrochemical measurements. The XRD result shows that the Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ materials prepared by different methods all form a pure phase with good crystallinity. SEM images and BET data present that the SC-material exhibited the smallest particle size (ca. 0.1 μm) and the highest surface area (7.4635 m² g⁻¹). The tap density of SC-material is lower than that of CP- and SG-materials. The result of rate performance tests indicates that the SC-material showed the best rate capability with the highest discharge capacity of 178 mAh g⁻¹ at 5.0 C, followed by SG-material and then CP-material. However, the cycling stability of SC-material tested at 0.1 and 0.5 C is relatively poor as compared to that of SG-material and CP-material. The result of EIS measurements reveals that large surface area and small particle size of the SC-electrode result in more SEI layer formation because of the increased side reactions with the electrolyte during cycling, which deteriorates the electrode/electrolyte interface and thus leads to the faster capacity fading of the SC-material.