Synthesis and electrochemical characterization of LiCoxMn1−xPO4/C nanocomposites

LiCo_xMn_1−xPO₄/C nanocomposites (0 ≤ x ≤ 1.0) were prepared by a combination of spray pyrolysis at 300 °C and wet ball-milling followed by heat treatment at 500 °C for 4 h in 3% H₂ + N₂ atmosphere. X-ray diffraction analysis indicated that all samples had the single phase olivine structures indexed by orthorhombic Pmna. The lattice parameters linearly decreased with increasing cobalt content, which confirmed the existence of solid solutions. It was clearly seen from the scanning electron microscopy observation that the LiCo_xMn_1−xPO₄/C samples were agglomerates with approximately 100 nm primary particles. The LiCo_xMn_1−xPO₄/C nanocomposites were used as cathode materials for lithium batteries, and electrochemical performance was comparatively investigated with cyclic voltammetry and galvanostatic charge–discharge test using the Li?1 M LiPF₆ in EC:DMC = 1:1?LiCo_xMn_1−xPO₄/C cells at room temperature. The cells at 0.05 C charge–discharge rate delivered first discharge capacities of 165 mAh g⁻¹ (96% of theoretical capacity) at x = 0, 136 mAh g⁻¹ at x = 0.2, 132 mAh g⁻¹ at x = 0.5, 125 mAh g⁻¹ at x = 0.8 and 132 mAh g⁻¹ (79% of theoretical capacity) at x = 1.0, respectively. While the first discharge capacity increased with the cobalt content at high charge–discharge rates more than 0.5 C due to higher electronic conductivity of LiCoPO₄ in comparison with LiMnPO₄, the cycleability of cell became worse with increasing the amount of cobalt. The existence of Mn²⁺ seemed to enhance the cycleability of LiCo_xMn_1−xPO₄/C nanocomposite cathode.     

Synthesis and microstructure of (LaSr)MnO3 and (LaSr)FeO3 ceramics by a reaction-sintering process

(La_xSr_1−x)MnO₃ (LSMO) and (La_xSr_1−x)FeO₃ (LSFO) (x = 0.2–0.4) ceramics prepared by a simple and effective reaction-sintering process were investigated. Without any calcination involved, La₂O₃ and SrCO₃ were mixed with MnO₂ (LSMO) or Fe₂O₃ (LSFO) then pressed and sintered directly. LSMO and LSFO ceramics were obtained after 2 and 4 h sintering at 1350–1400 and 1200–1280 °C, respectively. Grain size decreased as La content increased in LSMO and LSFO ceramics.     

High temperature phase stabilities and electrochemical properties of InBaCo4−xZnxO7 cathodes for intermediate temperature solid oxide fuel cells

InBaCo_4−xZn_xO₇ oxides have been synthesized and characterized as cathode materials for intermediate temperature solid oxide fuel cells (IT-SOFC). The effect of Zn substitution for Co on the structure, phase stability, thermal expansion, and electrochemical properties of the InBaCo_4−xZn_xO₇ has been investigated. The increase in the Zn content from x = 1 to 1.5 improves the high temperature phase stability at 600 °C and 700 °C for 100 h, and chemical stability against a Gd_0.2Ce_0.8O_1.9 (GDC) electrolyte. Thermal expansion coefficient (TEC) values of the InBaCo_4−xZn_xO₇ (x = 1, 1.5, 2) specimens were determined to be 8.6 × 10⁻⁶ to 9.6 × 10⁻⁶/°C in the range of 80–900 °C, which provides good thermal expansion compatibility with the standard SOFC electrolyte materials. The InBaCo_4−xZn_xO₇ + GDC (50:50 wt.%) composite cathodes exhibit improved cathode performances compared to those obtained from the simple InBaCo_4−xZn_xO₇ cathodes due to the extended triple-phase boundary (TPB) and enhanced oxide-ion conductivity through the GDC portion in the composites.     

Synthesis and properties of (BaxPb1−x)(Zn1/3Nb2/3)O3 relaxor ferroelectric ceramics using a reaction-sintering process

(Ba_xPb_1−x)(Zn_1/3Nb_2/3)O₃ (BPZN; x = 0.06–0.1) relaxor ferroelectric ceramics produced using a reaction-sintering process were investigated. Without any calcination involved, the mixture of raw materials was pressed and sintered directly. BPZN ceramics of 100% perovskite phase were obtained. Highly dense BPZN ceramics with a density higher than 98.5% of theoretical density could be obtained. Maximum dielectric constant K_max 13,500 (at 75 °C), 19,600 (at 50 °C) and 14,800 (at 28 °C) at 1 kHz could be obtained in 6BPZN, 8BPZN and 10BPZN, respectively. Dielectric maximum temperature (T_max) in BPZN ceramics via reaction-sintering process is lower than BPZN ceramics prepared via B-site precursor route.     

The effect of co-doping with MgO and Yb2O3 on the structure and electrical conductivity of the Sm2Zr2O7 pyrochlore

SmYb_1−xMg_xZr₂O_7−x/2 (0 ≤ x ≤ 0.15) ceramics are pressureless-sintered at 1973 K for 10 h in air. The structure and electrical conductivity of SmYb_1−xMg_xZr₂O_7−x/2 ceramics are investigated by the X-ray diffraction, scanning electron microscopy and impedance spectroscopy measurements. SmYb_1−xMg_xZr₂O_7−x/2 ceramics exhibit a defect fluorite-type structure. The measured electrical conductivities of SmYb_1−xMg_xZr₂O_7−x/2 ceramics obey the Arrhenius relation, and electrical conductivity of each composition increases with increasing temperature from 673 to 1173 K. At identical temperature levels, the electrical conductivity of SmYb_1−xMg_xZr₂O_7−x/2 ceramics gradually increases with increasing magnesia content. SmYb_1−xMg_xZr₂O_7−x/2 ceramics are oxide-ion conductors in the oxygen partial pressure range of 1.0 × 10⁻⁴ to 1.0 atm at all test temperature levels. The electrical conductivity obtained in SmYb_1−xMg_xZr₂O_7−x/2 ceramics reaches the highest value of 2.72 × 10⁻³ S cm⁻¹ at 1173 K for the SmYb_0.85Mg_0.15Zr₂O_6.925 ceramic.     

Decolorization of methylene blue by heterogeneous Fenton reaction using Fe3−xTixO4 (0 ≤ x ≤ 0.78) at neutral pH values

In this work, a series of Fe_3−xTi_xO₄ (0 ≤ x ≤ 0.78) was synthesized using a new soft chemical method. The synthetic Fe_3−xTi_xO₄ were characterized using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Mössbauer spectroscopy, thermogravimetric and differential scanning calorimetry (TG–DSC) analyses. The results showed that they were spinel structures and Ti was introduced into their structures.Then, decolorization of methylene blue (MB) by Fe_3−xTi_xO₄ in the presence of H₂O₂ at neutral pH values was studied using UV–vis spectra, dissolved organic carbon (DOC) and element C analyses. Furthermore, the degradation products remained in reaction solution after the decolorization were identified using ionic chromatography (IC), ¹³C nuclear magnetic resonance spectra (NMR), liquid chromatography and mass spectrometry (LC–MS). Although small amounts of MB were mineralized, the aromatic rings in MB were destroyed completely after the decolorization. Decolorization of MB by Fe_3−xTi_xO₄ in the presence of H₂O₂ was promoted remarkably with the increase of Ti content in Fe_3−xTi_xO₄ due to the enhancement of both adsorption and degradation of MB on Fe_3−xTi_xO₄.     

Structure and magnetic properties of Fe1−xCox nanowires in self-assembled arrays

Fe_1−xCo_x nanowires in self-assembled arrays with varying compositions were produced by the template-assisted pulsed electrochemical deposition method. The structural and magnetic properties of the arrays were investigated using several experimental techniques. TEM analyses indicated that the nanowires were regular, uniform, 8 μm in length and 50 nm in diameter. The results of X-ray diffraction indicated that the body-centered-cubic (bcc) (α), face-centered-cubic (fcc) (γ), and hexagonal-close-packed (hcp) () Fe–Co phases appeared in different compositions. Magnetic measurements showed that the coercivity and squareness of the hysteresis loops of the Fe_1−xCo_x changed with their compositions, which may be attributable to shape anisotropy. The room temperature ⁵⁷Fe Mössbauer spectra of the arrays of the Fe_1−xCo_x nanowires revealed strong shape anisotropy.     

Preparation and electrochemical properties of Cr-doped Li9V3(P2O7)3(PO4)2 as cathode materials for lithium-ion batteries

Cr-doped Li₉V_3−xCr_x(P₂O₇)₃(PO₄)₂ (x = 0.0–0.5) compounds have been prepared using sol–gel method. The Rietveld refinement results indicate that single-phase Li₉V_3−xCr_x(P₂O₇)₃(PO₄)₂ (x = 0.0–0.5) with trigonal structure can be obtained. Although the initial specific capacity decreased with Cr content at a lower current rate, both cycle performance and rate capability have excited improvement with moderate Cr-doping content. Li₉V_2.8Cr_0.2(P₂O₇)₃(PO₄)₂ compound presents the good electrochemical rate and cyclic ability. The enhancement of rate and cyclic capability may be attributed to the optimizing particle size, morphologies, and structural stability during the proper amount of Cr-doping (x = 0.2) in V sites.     

Microwave dielectric properties of SnO2-doped CaSiO3 ceramics

SnO₂-doped CaSiO₃ ceramics were successfully synthesized by a solid-state method. Effects of different SnO₂ additions on the sintering behavior, microstructure and dielectric properties of Ca(Sn_1−xSi_x)O₃ (x=0.5–1.0) ceramics have been investigated. SnO₂ improved the densification process and expanded the sintering temperature range effectively. Moreover, Sn⁴⁺ substituting for Si⁴⁺ sites leads to the emergence of Ca₃SnSi₂O₉ phase, which has a positive effect on the dielectric properties of CaO–SiO₂–SnO₂ materials, especially the Qf value. The Ca(Sn_0.1Si_0.9)O₃ ceramics sintered at 1375 °C possessed good microwave dielectric properties: ε_r =7.92, Qf =58,000 GHz and τ_f=−42 ppm/°C. The Ca(Sn_0.4Si_0.6)O₃ ceramics sintered at 1450 °C also exhibited good microwave dielectric properties of ε_r=9.27, Qf=63,000 GHz, and τ_f=−52 ppm/°C. Thus, they are promising candidate materials for millimeter-wave devices.     

Dielectric and mechanical properties of porous Si3N4 ceramics prepared via low temperature sintering

Borophosphosilicate bonded porous silicon nitride (Si₃N₄) ceramics were fabricated in air using a conventional ceramic process. The porous Si₃N₄ ceramics sintered at 1000–1200 °C shows a relatively high flexural strength and good dielectric properties. The influence of the sintering temperature and contents of additives on the flexural strength and dielectric properties of porous Si₃N₄ ceramics were investigated. Porous Si₃N₄ ceramics with a porosity of 30–55%, flexural strength of 40–130 MPa, as well as low dielectric constant of 3.5–4.6 were obtained.     

Synthesis of La1−xSrxMnO3 powders by polymerizable complex method: Evaluation of structural, morphological and electrical properties

Lanthanum strontium manganite (La_1−xSr_xMnO₃, LSM) powders were synthesized by polymerizable complex method, based on complexation of metal ions (MI) with citric acid (CA) and polyesterification between CA and ethylene glycol (EG). Firstly, the effect of the molar ratio of CA:MI (=1–3) was investigated on the synthesis of La_0.7Sr_0.3MnO₃ powders, which were characterized by thermal analysis (TGA/DTA), X-ray diffraction (XRD), and scanning electron microscopy (SEM). The results indicated that the molar ratio CA:MI = 3 is adequate for a good crystallization of pure perovskite phase after calcination, with nanometric crystallite sizes and porous microstructure. For the La_0.7Sr_0.3MnO₃ sample synthesized with CA:MI ratio of 3, it was investigated the effect of calcination temperature, showing that the perovskite structure is better crystallized at 900 °C, without secondary phase formation. Using this same CA:MI ratio and calcination temperature, powders with different Sr content (x = 0.2–0.4) were synthesized, with surface areas of 4–10 m² g⁻¹. These powders were sintered at 1100 °C to produce porous pellets. The porosity of the sintered pellets and the electrical conductivity, measured by two-probe technique, increased with increasing Sr content.     

Mn influence on the electrochemical behaviour of Li3V2(PO4)3 cathode material

The role played by the substitution of Mn on the electrochemical behaviour of Li₃V₂(PO₄)₃ has been investigated. Independently of the synthesis route, the Mn doping improves the electrochemical features with respect to the undoped samples. Different reasons can be taken into consideration to explain the electrochemical enhancement. In the sol–gel synthesis the capacity slightly enhances due to the Mn substitution on both the V sites, within the solubility limit x = 0.124 in Li₃V_2−xMn_x(PO₄)₃. In the solid state synthesis the significant capacity enhancement is preferentially due to the microstructural features of the crystallites and to the LiMnPO₄ phase formation.     

Characterisation by TPR, XRD and NOx Storage Capacity Measurements of the Ageing by Thermal Treatment and SO2 Poisoning of a Pt/Ba/Al NOx-Trap Model Catalyst

The deactivation of a Pt/Ba/Al₂O₃ NO _x -trap model catalyst submitted to SO₂ treatment and/or thermal ageing at 800 °C was studied by H₂ temperature programmed reduction (TPR), X-ray diffraction (XRD) and NO _x storage capacity measurements.The X-ray diffractogram of the fresh sample exhibits peaks characteristic for barium carbonate. Thermal ageing leads to the decomposition of barium carbonate and to the formation of BaAl₂O₄. The TPR profile of the sulphated sample shows the presence of (i) surface aluminium sulphates, (ii) surface barium sulphates, (iii) bulk barium sulphates. The exposure to SO₂ after ageing leads to a small decrease of the surface barium-based sulphates, expected mainly as aluminate barium sulphates. This evolution can be attributed to a sintering of the storage material. TPR experiments also show that thermal treatment at 800 °C after the exposure to SO₂ involves the decomposition of aluminium surface sulphates to give mainly bulk barium sulphates, also pointed out by XRD. Thus, the thermal treatment at 800 °C leads to a stabilization of the sulphates.These results are in accordance with the NO _x storage capacity measurements. On non-sulphated catalysts, the treatment at 800 °C induces to a decrease of the NO _x storage capacity, showing that barium aluminate presents a lower NO _x storage capacity than barium carbonate. Sulphation strongly decreases the NO _x storage capacity of catalysts, whatever the initial thermal treatment, showing that barium sulphates inhibit the NO₂ adsorption. Moreover, the platinum activity for the NO to NO₂ oxidation is lowered by thermal treatments.     

Highly oriented diamond growth on SixGe1−x (100) thin films

Highly oriented (100) diamond films have been successfully grown on Si_xGe_1−x (100) thin films by bias enhanced nucleation (BEN) in microwave plasma chemical vapor deposition (MPCVD) system. Raman spectra show the 1332 cm⁻¹ peak which proves the formation of diamond. Diamond nucleation density on Si_xGe_1−x substrate estimated by scanning electron microscopy is higher than 10⁹ cm⁻². The interface between diamond and Si_xGe_1−x substrate was characterized by transmission electron microscopy (TEM). About 20 nm decrease in thickness of the Si_xGe_1−x film was observed after bias enhanced nucleation step. TEM shows the existence of silicon carbide and heteroepitaxial diamond grains grown on Si_xGe_1−x substrate. Characterization from high-resolution TEM on the specimen of short time deposition reveals that a number of epitaxial diamond grains were directly nucleated on Si_xGe_1−x with {111} interplanar spacing ratio of diamond and Si_xGe_1−x of 2:3. The diamond nucleation is found to be preferred on the ridge position of the rough substrate surface. Diamond {100} facets were quickly developed in the early stage of growth.     

Surface properties and catalytic performance of La1−xSrxCrO3 perovskite-type oxides for CO and C3H6 combustion

Catalytic CO oxidation and C₃H₆ combustion have been studied over La_1−xSr_xCrO₃ (x = 0.0–0.3) oxides prepared by solid-state reaction and characterised by X-ray diffraction (XRD), nitrogen adsorption (BET analysis) and X-ray photoelectron spectroscopy (XPS). The expected orthorhombic perovskite structure of the chromite is observed for all levels of substitution. However, surface segregation of strontium along with a chromium oxidation process, leading to formation of Cr⁶⁺-containing phases, is produced upon increasing x and shown to be detrimental to the catalytic activity. Maximum activity is achieved for the catalyst with x = 0.1 in which mixed oxide formation upon substitution of lanthanum by strontium in the chromite becomes maximised.     

Exceptional Activity for NOx Reduction at Low Temperatures Using Combinations of Hydrogen and Higher Hydrocarbons on Ag/Al2O3 Catalysts

The effect of the addition of hydrogen on the SCR of NO _x with a hydrocarbon reaction was investigated. It was found that hydrogen had a remarkable effect on the temperature range over which NO _x could be reduced during the SCR reaction with octane. Reduction of NO _x was initiated at as low a temperature as 100 °C and >95% NO _x conversion was achieved over a temperature range of 200–450 °C. Hydrogen has the effect of activating octane at lower temperatures and also promotes the oxidation of NO to NO₂ in the absence of hydrocarbon. Transient kinetic and in situ DRIFTS measurements indicated that hydrogen has a direct role in the reaction mechanism by either promoting the formation and storage of an organic C = N species which can then readily reduce NO _x and/or removing a species which acts as a poison to the SCR reaction at low temperatures.     

Fundamental Investigations of Thermal Aging Phenomena of Model NOx Storage Systems

Investigations of the aging behavior induced by high temperatures coupled with oxidizing atmosphere of model NO _x storage systems Ba/Al₂O₃ and Ba/CeO₂ are reported in this paper. The samples were prepared, calcined and exposed to temperatures between 500 and 1000 °C in air for 12 h for thermal aging. Samples were characterized with XRD, HRSEM, DSC-TGA-MS and BET analyses. In XRD investigations of all model systems calcined at 500 °C for 2 h, the NO _x storage component was present in form of BaCO₃. The release of CO₂ as a result of the decarbonization of the NO _x storage component at increased temperatures was verified by thermogravimetric investigations. In the case of Ba/Al₂O₃, already during calcination a partial reaction of the NO _x storage component with Al₂O₃ resulting in the formation of barium aluminate was observed. In the model system Ba/CeO₂ the decomposition of the barium carbonate started above 780 °C and the formation of a barium cerium mixed oxide was observed. The presence of the barium containing NO _x storage component has a strong influence on the specific surface area of the model NO _x storage systems. The morphology and crystallite size of CeO₂ modified with the barium containing NO _x storage component exhibited distinct changes compared to the unmodified oxide. The NO _x storage efficiency determined by model gas tests of freshly prepared and engine aged model NO _x storage catalysts correlates well with the above described observations.     

Preparation and characterization of 10 mol% Gd doped CeO2 (GDC) electrolyte for SOFC applications

Ceria-based materials are prospective electrolytes for low and intermediate temperature solid oxide fuel cells. In the present work, fully dense CeO₂ ceramics doped with 10 mol% gadolinium (Gd_0.1Ce_0.9O_1.95, GDC) have been prepared with a Pechini method. Characterization studies were realized with thermo-gravimetric analysis (TGA), differential thermal analysis (DTA), mass spectroscopy (MS), high temperature FT-IR (HT-FTIR) and X-ray diffraction analysis (XRD). A single-phase with a fluorite type structure was found to form at a relatively low calcination temperature of 500 °C. Dense GDC pellets having 98% of the relative density were obtained at sintering temperature of 1400 °C/6 h, which gave significantly higher total ionic conductivity of 3.4×10⁻² S cm⁻¹ at 500 °C in air. The present work showed that the Pechini method is a relatively low-temperature preparation technique to synthesize Gd_0.1Ce_0.9O_1.95 powders that provided high sinterability and good ionic conductivity.     

Influence of the Storage Material on the Storage of NOx at Low Temperatures

The NO _x storage performance at low temperature (100–200 °C) has been studied for model NO _x storage catalysts. The catalysts were prepared by sequentially depositing support, metal oxide and platinum on ceramic monoliths. The support material consisted of acidic aluminium silicate, alumina or basic aluminium magnesium oxide, and the added metal oxide was either ceria or barium oxide. The NO _x conversion was evaluated under net-oxidising conditions with transients between lean and rich gas composition and the NO _x storage performance was studied by isothermal adsorption of NO₂ followed by temperature programmed desorption of adsorbed species. The maximum in NO _x storage capacity was observed at 100 °C for all samples studied. The Pt/BaO/Al₂O₃ catalyst stored about twice the amount of NO _x compared with the Pt/Al₂O₃ and Pt/CeO₂/Al₂O₃ samples. The storage capacity increased with increasing basicity of the support material, i.e. Pt/Al₂O₃·SiO₂ < Pt/Al₂O₃ < Pt/Al₂O₃ · MgO. Water did not significantly affect the NO _x storage performance for Pt/Al₂O₃ or Pt/BaO/Al₂O₃.