Nb2O5 as efficient and recyclable photocatalyst for indigo carmine degradation

Heterogeneous photocatalysis is a significant green technology for application in water purification. The application of Nb₂O₅ catalyst for the photodegradation of contaminants is few reported in the literature. Thus, the Nb₂O₅ catalyst was characterized by SEM, FTIR, surface area and charge surface density. This catalyst was applied to degrade indigo carmine dye, which was compared with degradation catalyzed by TiO₂ and ZnO. Almost 100% of dye degradation occurred at 20, 45 and 90 min for TiO₂, ZnO and Nb₂O₅, respectively. The effect of Nb₂O₅ catalyst concentration, pH and ionic strength (μ) was investigated. The Nb₂O₅ activity increased at 0.7 g/L and for higher catalyst concentrations the degradation was kept constant. Degradation of indigo carmine dye catalyzed by Nb₂O₅ was improved at pH < 4.0 and μ = 0.05 mol/L. TiO₂, ZnO and Nb₂O₅ were recovered and re-applied in other nine reaction cycles. While TiO₂ and ZnO have an abrupt loss of their catalytic activity, Nb₂O₅ maintained 85% of catalytic activity after 10 reaction cycles.     

Electrochemical properties of bare and Ta-substituted Nb2O5 nanostructures

In this work, bare and Ta-substituted Nb₂O₅ nanofibers are prepared by electrospinning followed by sintering at temperatures in the 800–1100 °C range for 1 h in air. Obtained bare and Ta-substituted Nb₂O₅ polymorphs are characterized by X-ray diffraction, scanning electron microscopy, density measurement, and Brunauer, Emmett and Teller surface area. Electrochemical properties are evaluated by cyclic voltammetry and galvanostatic techniques. Cycling performance of Nb₂O₅ structures prepared at temperature 800 °C, 900 °C, and 1100 °C shows following discharge capacity at the end of 10th cycle: 123, 140, and 164 (±3) mAh g⁻¹, respectively, in the voltage range 1.2–3.0 V and at current rate of 150 mA g⁻¹ (1.5 C rate). Heat treated composite electrode based on M-Nb₂O₅ (1100 °C) in argon atmosphere at 220 °C, shows an improved discharge capacity of 192 (±3) mAh g⁻¹ at the end of 10th cycle. The discharge capacity of Ta-substituted Nb₂O₅ prepared at 900 °C and 1100 °C showed a reversible capacity of 150, 202 (±3) mAh g⁻¹, respectively, in the voltage range 1.2–3.0 V and at current rate of 150 mA g⁻¹. Anodic electrochemical properties of M-Nb₂O₅ deliver a reversible capacity of 382 (±5) mAh g⁻¹ at the end of 25th cycle and Ta-substituted Nb₂O₅ prepared at 900 °C, 1000 °C and 1100 °C shows a reversible capacity of 205, 130 and 200 (±3) mAh g⁻¹ (at 25th cycle) in the range, 0.005–2.6 V, at current rate of 100 mA g⁻¹.     

The catalytic performance in oxidative coupling of methane and the surface basicity of La2O3, Nd2O3, ZrO2 and Nb2O5

The catalytic performance in oxidative coupling of methane (OCM) of unmodified pure La₂O₃, Nd₂O₃, ZrO₂ and Nb₂O₅ has been investigated under various conditions. The results confirmed that the activity of La₂O₃ and Nd₂O₃ was always much higher than that of the remaining two. The surface basicity/base strength distribution of pure La₂O₃, Nd₂O₃, ZrO₂ and Nb₂O₅ was measured using a test reaction of transformation of 2-butanol and a temperature-programmed desorption of CO₂. Both methods showed that La₂O₃ and Nd₂O₃ had high basicity and contained medium and strong basic sites (lanthanum oxide more and neodymium oxide somewhat less). ZrO₂ had only negligible amount of weak basic sites and Nb₂O₅ was rather acidic. The confrontation of the basicity and catalytic performance indicated that in the case of investigated oxides, the basicity (especially strong basic sites) could be a decisive factor in determination of the catalytic activity in OCM. Only in the case of ZrO₂ it was observed a moderate catalytic performance in spite of negligible basicity. The influence of a gas atmosphere used in the calcination of oxides (flowing oxygen, helium and nitrogen) on their basicity and catalytic activity in OCM had been also investigated. Contrary to earlier observations with MgO, no effect of calcination atmosphere on the catalytic performance of investigated oxides in OCM and on their basicity was observed.     

Investigation on electrochemical reduction process of Nb2O5 powder in molten CaCl2 with metallic cavity electrode

The direct electrochemical reduction process of Nb₂O₅ powder was investigated by cyclic voltammetry and constant potential electrolysis with a novel metallic cavity electrode in molten calcium chloride at 850 °C. The products of both constant potential and constant voltage electrolysis were characterized by XRD, SEM and EDX. CaNb₂O₆ was formed upon addition of solid Nb₂O₅ into molten CaCl₂ when CaO was present. During the electrolysis solid Nb₂O₅ was reduced to various niobium oxides of lower oxidation states, including some composite oxides, and then was converted completely to metallic niobium near −0.35 V (vs. Ag/AgCl), which was more positive than the reduction potential of Ca²⁺. Constant potential electrolysis was applied at the potentials near the reduction current peaks derived from the cyclic voltammetry curves, and cell voltages were monitored. The voltage was near 2.4 V when the oxide was metallized at −0.35 V (vs. Ag/AgCl). Nb₂O₅ pellet could be used to prepared metallic niobium at cell voltage 2.4 V in a larger electrolysis bath filled with calcium chloride at 850 °C. The experiment results further demonstrated the direct electrochemical reduction mechanism of Nb₂O₅ powder in a molten system.     

XANES study of polyaniline-V2O5 and sulfonated polyaniline-V2O5 nanocomposites

In this work, two materials for secondary lithium battery cathodes formed by polyaniline-V₂O₅ and sulfonated polyaniline-V₂O₅, which have a higher charge capacity than the V₂O₅ xerogel, were synthesized. X-ray absorption and Fourier transform infrared spectroscopies were employed to analyze the short-range interactions in these materials. Based on these experiments, it was possible to observe significant differences in the symmetry of the VO₅ units, and this was attributed to the intimate contact between V₂O₅ and the polymers, and to some flexibility of the VO₅ square pyramids due to the low range order of the nanocomposites.     

Long-term degradation of Ta2O5-doped Bi2O3 systems

Bismuth oxide in δ-phase is a well-known high oxygen ion conductor and can be used as an electrolyte for intermediate temperature solid oxide fuel cells (IT-SOFCs). 5-10 mol% Ta₂O₅ are doped into Bi₂O₃ to stabilize δ-phase by solid state reaction process. One Bi₂O₃ sample (7.5TSB) was stabilized by 7.5 mol% Ta₂O₅ and exhibited single phase δ-Bi₂O₃-like (type I) phase. Thermo-mechanical analyzer (TMA), X-ray diffractometry (XRD), AC impedance and high-resolution transmission electron microscopy (HRTEM) were used to characterize the properties. The results showed that holding at 800-850 °C for 1 h was the appropriate sintering conditions to get dense samples. Obvious conductivity degradation phenomenon was obtained by 1000 h long-term treatment at 650 °C due to the formation of α-Bi₂O₃ phase and Bi₃TaO₇, and 〈1 1 1〉 vacancy ordering in Bi₃TaO₇ structure.     

Study of ruthenium supported on Ta2O5–ZrO2 and Nb2O5–ZrO2 as catalysts for the partial oxidation of methane

Ru-based catalysts supported on Ta₂O₅–ZrO₂ and Nb₂O₅–ZrO₂ are studied in the partial oxidation of methane at 673–873 K. Supports with different Ta₂O₅ or Nb₂O₅ content were prepared by a sol–gel method, and RuCl₃ and RuNO(NO₃)₃ were used as precursors to prepare the catalysts (ca. 2 wt.% Ru). At 673 K high selectivity to CO₂ was found. An increase of temperature up to 773 K produced an increase in the selectivity to syngas (H₂/CO = 2.2–3.1), and this is related with the transformation of RuO₂ to metallic Ru as was determined from XRD and XPS results. At 873 K and with co-fed CO₂ an increase of the catalytic activity and CO selectivity was found. A TOF value of 5.7 s⁻¹ and H₂/CO ratio ca. 1 was achieved over Ru(Cl)/6TaZr. Catalytic results are discussed as a function of the support composition and characteristics of Ru-based phases.     

Mixed oxides Ca2Fe2O5 and Ca2Co2O5 as anode materials for Li-ion batteries

The electrochemical performance of mixed oxides, Ca₂Fe₂O₅ and Ca₂Co₂O₅ for use in Li-ion batteries was studied with Li as the counter electrode. The compounds were prepared and characterized by X-ray diffraction and SEM. Ca₂Fe₂O₅ showed a reversible capacity of 226 mAh/g at the 14th cycle and retained 183 mAh/g at the end of 50 cycles at 60 mA/g in the voltage window 0.005-2.5 V. A reversible capacity in the range, 365-380 mAh/g, which is stable up to 50 charge-discharge cycles is exhibited by Ca₂Co₂O₅ in the voltage window, 0.005-3.0 V and at 60 mA/g. This corresponds to recycleable moles of Li of 3.9±0.1 (theoretical: 4.0). Significant improvement in the cycling performance and attainable reversible capacity were noted for Ca₂Co₂O₅ on cycling to an upper cut-off voltage of 3.0 V as compared to 2.5 V. Coulombic efficiency for both compounds is >98%. Electrochemical impedance spectroscopy (EIS) data clearly indicate the reversible formation/decomposition of polymeric surface film on the electrode surface of Ca₂Co₂O₅ in the voltage window, 0.005-3.0 V. Cyclic voltammetry results compliment the galvanostatic cycling data.     

Al2O3-coated SnO2/TiO2 composite electrode for the dye-sensitized solar cell

A novel Al₂O₃-coated SnO₂/TiO₂ composite electrode has been applied to the dye-sensitized solar cell. In such an electrode, two kinds of energy barriers (SnO₂/TiO₂ and TiO₂/Al₂O₃) were designed to suppress the recombination processes of the photo-generated electrons and holes. After the SnO₂ was modified by colloid TiO₂, the photoelectric conversion efficiency of the SnO₂/TiO₂ composite cell increased to 2.08% by a factor of 2.8 comparing with that of the SnO₂ cell. The Al₂O₃ layer on the SnO₂/TiO₂ composite electrode further suppressed the generation of the dark current, resulting in 37% improvement in device performance comparing with the SnO₂/TiO₂ cell.     

SO2 and NO removal from flue gas over V2O5/AC at lower temperatures — role of V2O5 on SO2 removal

Supporting V₂O₅ onto an activated coke (AC) has been reported to significantly increase the AC's activity in simultaneous SO₂ and NO removal from flue gas. To understand the role of V₂O₅ on SO₂ removal, V₂O₅/AC is studied through SO₂ removal reaction, surface analysis, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FTIR) techniques. It is found that the main role of V₂O₅ in SO₂ removal over V₂O₅/AC is to catalyze SO₂ oxidation through a VOSO₄-like intermediate species, which reacts with O₂ to form SO₃ and V₂O₅. The SO₃ formed transfers from the V sites to AC sites and then reacts with H₂O to form H₂SO₄. At low V₂O₅ loadings, a V atom is able to catalyze as many as 8 SO₂ molecules to SO₃. At high V₂O₅ loadings, however, the number of SO₂ molecules catalyzed by a V atom is much less, due possibly to excessive amounts of V₂O₅ sites in comparison to the pores available for SO₃ and H₂SO₄ storage.     

Synthesis, structure and photoelectrochemical performance of micro/nano-textured ZnO/eosin Y electrodes

Micro/nano-textured ZnO thick films were synthesized through deposition and pyrolysis of layered hydroxide zinc acetate (LHZA), Zn₅(OH)₈(CH₃COO)₂·2H₂O. LHZA films having a unique, rose-like morphology were initially deposited on conducting glass sheets in a chemical bath composed of methanol and zinc acetate dihydrate at 60 °C under neutral conditions. Pyrolysis of the LHZA films resulted in formation of ZnO without destroying the original morphology. Pyrolysis temperatures were found to greatly influence grain sizes and specific surface areas of the ZnO films. Photoelectrochemical performance of the films as ZnO/eosin Y electrodes was investigated in dye-sensitized solar cells using an I⁻/I₃⁻ redox electrolyte solution. The cell using the ZnO film pyrolyzed at 150 °C exhibited overall light to electricity conversion efficiencies of 2.0 and 3.3% under an AM-1.5 illumination at 100 and 10 mW cm⁻², respectively. While microscale pores in the electrodes facilitated mass transfer of fluid electrolytes in the depth direction, nanoscale pores contributed to an increase in the amount of adsorbed dye. The maximum incident photon-to-current conversion efficiency (IPCE) of the electrode reached 84.9% at a wavelength of 530 nm.     

A comparative study on IrO2-Ta2O5 coated titanium electrodes prepared with different methods

The electrodes of IrO₂-Ta₂O₅ coated titanium were prepared using conventionally thermal decomposition procedure and polymer sol-gel (Pechini) method, respectively. The microstructure and electrochemical properties of the electrodes were studied with scanning electron microscope (SEM), energy dispersive X-ray (EDX), atomic force microscope (AFM), potentiodynamic polarization, cyclic voltammetry, electrochemical impedance spectroscopy and accelerated life test. As compared with the electrode formed using the traditional method of thermal decomposition, the oxide electrode prepared by Pechini method presents morphology of higher nano-scale roughness and more uniform surface composition with little precipitates. It also has larger electrochemically active surface area, better electrocatalytic activity for oxygen evolution and higher stability.     

Effect of Y2O3 and Er2O3 co-dopants on phase stabilization of bismuth oxide

Bi₂O₃ compositions were prepared to investigate the effect of rare earth metal oxides as co-dopants on phase stability of bismuth oxide. Compositions containing 9-14 mol% of Y₂O₃ and Er₂O₃ were synthesized by solid state reaction. The structural characterization was carried out using X-ray powder diffraction. The XRD results show that the samples containing 12 and 14 mol% total dopants had cubic structure, whereas the samples with lower dopant concentrations were tetragonal. Comparing the lattice parameters of the cubic phases of (Bi₂O₃)_0.88(Y₂O₃)_0.06(Er₂O₃)_0.06 and (Bi₂O₃)_0.86(Y₂O₃)_0.07(Er₂O₃)_0.07 revealed that lattice parameter decreases by increasing the dopant concentration. The XRD pattern and the powder density results indicated the formation of solid solution in the studied systems. After annealing samples with cubic phase at 600 °C for various periods of time, phase transformation to tetragonal and rhombohedral occurs.     

Gas-phase elemental mercury capture by a V2O5/AC catalyst

Gas-phase elemental mercury (Hg⁰) capture by an activated coke (AC) supported V₂O₅ (V₂O₅/AC) catalyst was studied in simulated flue gas and compared with that by the AC. The study on the influences of V₂O₅ loading, temperature, capture time and flue gas components (O₂, SO₂, H₂O and N₂) shows that the Hg⁰ capture capability of V₂O₅/AC is much higher than that of AC. It increases with an increase in V₂O₅ loading and is promoted by O₂, which indicates the important role of V₂O₅ in Hg⁰ oxidation and capture; it is promoted slightly by SO₂ but inhibited by H₂O; it increases with an increase in temperature up to 150 °C when Hg desorption starts. X-ray photoelectron spectroscopy analysis and sequential chemical extraction experiments indicate that the main states of Hg captured on V₂O₅/AC are HgO and HgSO₄. Temperature programmed desorption experiments were also made to understand the stability of the Hg captured.     

Corrosion mechanisms of Al2O3/MgAl2O4 by V2O5, NiO, Fe2O3 and vanadium slag

The effects of V₂O₅, NiO, Fe₂O₃ and vanadium slag on the corrosion of Al₂O₃ and MgAl₂O₄ have been investigated. The specimens of Al₂O₃ and MgAl₂O₄ with the respective oxides above mentioned were heated at 10 °C/min from room temperature up to three different temperatures: 1400, 1450 and 1500 °C. The corrosion mechanisms of each system were followed by XRD and SEM analyses. The results obtained showed that Al₂O₃ was less affected by the studied oxides than MgAl₂O₄. Alumina was only attacked by NiO forming NiAl₂O₄ spinel, while the MgAl₂O₄ spinel was attacked by V₂O₅ forming MgV₂O₆. It was also observed that Fe₂O₃ and Mg, Ni, V and Fe present in the vanadium slag diffused into Al₂O₃. On the other hand, the Fe₂O₃ and Ca, S, Si, Na, Mg, V and Fe diffused into the MgAl₂O₄ structure. Finally, the results obtained were compared with those predicted by the FactSage software.     

Preparation of columbite MgNb2O6 and ZnNb2O6 ceramics by reaction-sintering

Columbite MgNb₂O₆ (MN) and ZnNb₂O₆ (ZN) ceramics produced by the reaction-sintering process were investigated. Secondary phases Mg_0.652Nb_0.598O_2.25 and Mg_0.66Nb_11.33O₂₉ were found in MgNb₂O₆ pellets. After 1250 °C sintering for 2 h, a density 4.85 g/cm³ (97.1% of the theoretical value) was obtained in MgNb₂O₆ pellets. In ZnNb₂O₆ pellets, no secondary phase formed. The maximum density 5.55 g/cm³ (98.7% of the theoretical value) occurs at 1200 and 1180 °C sintering for 2 and 4 h, respectively.     

Preparation of micro-dot electrodes of LiCoO2 and Li4Ti5O12 for lithium micro-batteries

Fabrications of micro-dot electrodes of LiCoO₂ and Li₄Ti₅O₁₂ on Au substrates were demonstrated using a sol-gel process combined with a micro-injection technology. A typical size of prepared dots was about 100 μm in diameter, and the dot population on the substrate was 2400 dots cm⁻². The prepared LiCoO₂ and Li₄Ti₅O₁₂ micro-dot electrodes were characterized with scanning electron microscopy, X-ray diffraction, micro-Raman spectroscopy, and cyclic voltammetry. The prepared LiCoO₂ and Li₄Ti₅O₁₂ micro-dot electrodes were evaluated in an organic electrolyte as cathode and anode for lithium micro-battery, respectively. The LiCoO₂ micro-dot electrode exhibited reversible electrochemical behavior in a potential range from 3.8 to 4.2 V versus Li/Li⁺, and the Li₄Ti₅O₁₂ micro-dot electrode showed sharp redox peaks at 1.5 V.     

Effects of surface modification on the cycling stability of LiNi0.8Co0.2O2 electrodes by CeO2 coating

A high-performance LiNi_0.8Co_0.2O₂ cathode was successfully fabricated by a sol-gel coating of CeO₂ to the surface of the LiNi_0.8Co_0.2O₂ powder and subsequent heat treatment at 700 °C for 5 h. The surface-modified and pristine LiNi_0.8Co_0.2O₂ powders were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), slow rate cyclic voltammogram (CV), and differential scanning calorimetry (DSC). Unlike pristine LiNi_0.8Co_0.2O₂, the CeO₂-coated LiNi_0.8Co_0.2O₂ cathode exhibits no decrease in its original specific capacity of 182 mAh/g (versus lithium metal) and excellent capacity retention (95% of its initial capacity) between 4.5 and 2.8 V after 55 cycles. The results indicate that the surface treatment should be an effective way to improve the comprehensive properties of the cathode materials for lithium ion batteries.     

Role of ZnO in Cu/ZnO/Al2O3 catalyst for hydrogenolysis of butyl butyrate

For hydrogenolysis of butyl butyrate (BB), a series of Cu/ZnO/Al₂O₃ catalysts with different metal compositions were prepared, and characterized by N₂O chemisorption for measuring Cu surface area and by chromatographic experiment for determining the heat of BB adsorption. As a result, the presence of ZnO in Cu-based catalysts was found to enhance the catalytic activity of Cu due to dual function of ZnO. The Cu surface area was linearly correlated with the butanol productivity, demonstrating that ZnO exerts the structural function in Cu/ZnO/Al₂O₃ catalysts. Additionally, the role of ZnO as a chemical contributor was revealed such that its presence leads to lower activation energy of the surface reaction, thus resulting in higher Cu catalytic activity obtained at a low temperature such as 200 °C. Consequently, optimizing the Cu/Zn ratio in Cu/ZnO/Al₂O₃ catalyst is required to tune its structural and chemical characteristics of Cu metals, and thus to obtain a higher activity on the hydrogenolysis reaction.