Preparation and electrochemical capacitance of cobalt oxide (Co3O4) nanotubes as supercapacitor material

Cobalt oxide (Co₃O₄) nanotubes have been successfully synthesized by chemically depositing cobalt hydroxide in anodic aluminum oxide (AAO) templates and thermally annealing at 500 °C. The synthesized nanotubes have been characterized by scanning electron microscope (SEM), transmission electron microscope (TEM) and X-ray diffraction (XRD). The electrochemical capacitance behavior of the Co₃O₄ nanotubes electrode was investigated by cyclic voltammetry, galvanostatic charge-discharge studies and electrochemical impedance spectroscopy in 6 mol L⁻¹ KOH solution. The electrochemical data demonstrate that the Co₃O₄ nanotubes display good capacitive behavior with a specific capacitance of 574 F g⁻¹ at a current density of 0.1 A g⁻¹ and a good specific capacitance retention of ca. 95% after 1000 continuous charge-discharge cycles, indicating that the Co₃O₄ nanotubes can be promising electroactive materials for supercapacitor.     

Pseudocapacitive properties of electrodeposited porous nanowall Co3O4 film

A porous nanowall Co₃O₄ film is prepared by a facile cathodic electrodeposition. The as-prepared porous nanowall Co₃O₄ film shows a net-like porous structure with huge porosity. The porous network is made up of free standing interconnected Co₃O₄ nanoflakes with a thickness of 20 nm. As cathode material for pseudocapacitors, porous nanowall Co₃O₄ film exhibits weaker polarization, higher electrochemical reactivity and better cycling performance as compared to the dense Co₃O₄ film. The specific capacitance of porous nanowall Co₃O₄ film is 325 F g⁻¹ at 2 A g⁻¹ and 247 F g⁻¹ at 40 A g⁻¹, respectively, much higher than that of the dense Co₃O₄ film (230 F g⁻¹ at 2 A g⁻¹ and 167 F g⁻¹ at 40 A g⁻¹). The better pseudocapacitive performances of the porous nanowall Co₃O₄ film are attributed to its highly porous morphology, which provides large reaction surface and short ion diffusion paths, and relaxes the volume change caused by the reaction during the cycling process.     

Comparison of AlPO4- and Co3(PO4)2-coated LiNi0.8Co0.2O2 cathode materials for Li-ion battery

Electrochemical and thermal properties of Co₃(PO₄)₂- and AlPO₄-coated LiNi_0.8Co_0.2O₂ cathode materials were compared. AlPO₄-coated LiNi_0.8Co_0.2O₂ cathodes exhibited an original specific capacity of 170.8 mAh g⁻¹ and had a capacity retention (89.1% of its initial capacity) between 4.35 and 3.0 V after 60 cycles at 150 mA g⁻¹. Co₃(PO₄)₂-coated LiNi_0.8Co_0.2O₂ cathodes exhibited an original specific capacity of 177.6 mAh g⁻¹ and excellent capacity retention (91.8% of its initial capacity), which was attributed to a lithium-reactive Co₃(PO₄)₂ coating. The Co₃(PO₄)₂ coating material could react with LiOH and Li₂CO₃ impurities during annealing to form an olivine Li_xCoPO₄ phase on the bulk surface, which minimized any side reactions with electrolytes and the dissolution of Ni⁴⁺ ions compared to the AlPO₄-coated cathode. Differential scanning calorimetry results showed Co₃(PO₄)₂-coated LiNi_0.8Co_0.2O₂ cathode material had a much improved onset temperature of the oxygen evolution of about 218 °C, and a much lower amount of exothermic-heat release compared to the AlPO₄-coated sample.     

Facile synthesis of Co3O4 nanoflowers grown on Ni foam with superior electrochemical performance

Novel large-scale Co₃O₄ nanoflower (NF) structures on Ni foam are prepared for the first time via a general two-step synthesis. Through a controllable solvothermal process and hereafter with a post-calcination process in air, the NFs have been grown firmly on Ni foam, which is convenient for the construction of supercapacitors without any extra electrode preparation process. The pore sizes and the amount of Co₃O₄ NFs can be tuned through different post-calcination and solvothermal conditions, respectively. The electrochemical properties of the NFs are tested by cyclic voltammetry, galvanostatic charge–discharge in 6.0 M KOH solution. The results show that the NFs can have a specific capacitance of 1936.7 F g⁻¹ at a current density of 0.2 A g⁻¹ and a capacity retention of 78.2% after 1000 cycles at a current density of 3 A g⁻¹ (1309.4 F g⁻¹). The Co₃O₄ NFs grown on Ni foam with large area and superior electrochemical performance have great potential application in supercapacitors.     

Synthesis and characterization of high-density non-spherical Li(Ni1/3Co1/3Mn1/3)O2 cathode material for lithium ion batteries by two-step drying method

Non-spherical Li(Ni_1/3Co_1/3Mn_1/3)O₂ powders have been synthesized using a two-step drying method with 5% excess LiOH at 800 °C for 20 h. The tap-density of the powder obtained is 2.95 g cm⁻³. This value is remarkably higher than that of the Li(Ni_1/3Co_1/3Mn_1/3)O₂ powders obtained by other methods, which range from 1.50 g cm⁻³ to 2.40 g cm⁻³. The precursor and Li(Ni_1/3Co_1/3Mn_1/3)O₂ are characterized by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and scanning electron microscope (SEM). XPS studies show that the predominant oxidation states of Ni, Co and Mn in the precursor are 2⁺, 3⁺ and 4⁺, respectively. XRD results show that the Li(Ni_1/3Co_1/3Mn_1/3)O₂ material obtained by the two-step drying method has a well-layered structure with a small amount of cation mixing. SEM confirms that the Li(Ni_1/3Co_1/3Mn_1/3)O₂ particles obtained by this method are uniform. The initial discharge capacity of 167 mAh g⁻¹ is obtained between 3 V and 4.3 V at a current of 0.2 C rate. The capacity of 159 mAh g⁻¹ is retained at the end of 30 charge-discharge cycle with a capacity retention of 95%.     

Sol–gel approach for controllable synthesis and electrochemical properties of NiCo2O4 crystals as electrode materials for application in supercapacitors

In this work, NiCo₂O₄ coral-like porous crystals, nanoparticles and submicron-sized particles have been systematically prepared via a facile sol–gel method, using citric acid as the chelating ligand and H₂O (H₂O-DMF) as solvent. The experimental results reveal that the initial molar concentration of reactants, reaction time and solvent species involved are crucial for preparing the target products. The as-obtained samples were characterized by means of XRPD, FESEM, HRTEM, EDS and SAED techniques. Finally, the electrochemical performances of NiCo₂O₄ crystals with distinct morphologies were evaluated by cyclic voltammetry, and galvanostatic charge–discharge cycling techniques. The results show that submicron-sized NiCo₂O₄ particles exhibit the best capacitive properties with high specific capacitance and excellent cycle stability. At a high mass loading (5.6 mg cm⁻²), specific capacitance value of submicron-sized NiCo₂O₄/Ni electrode reaches as much as 217 F g⁻¹, and 96.3% of which can be still maintained after 600 charge–discharge cycles. Therefore, NiCo₂O₄ crystal is very promising for real application in supercapacitors.     

Effect of synthesis condition on the structural and electrochemical properties of Li[Ni1/3Mn1/3Co1/3]O2 prepared by the metal acetates decomposition method

In order to get homogeneous layered oxide Li[Ni_1/3Mn_1/3Co_1/3]O₂ as a lithium insertion positive electrode material, we applied the metal acetates decomposition method. The oxide compounds were calcined at various temperatures, which results in greater difference in morphological (shape, particle size and specific surface area) and the electrochemical (first charge profile, reversible capacity and rate capability) differences. The Li[Ni_1/3Mn_1/3Co_1/3]O₂ powders were characterized by means of X-ray diffraction (XRD), charge/discharge cycling, cyclic voltammetry and SEM. XRD experiment revealed that the layered Li[Ni_1/3Mn_1/3Co_1/3]O₂ material can be best synthesized at temperature of 800 °C. In that synthesized temperature, the sample showed high discharge capacity of 190 mAh g⁻¹ as well as stable cycling performance at a current density of 0.2 mA cm⁻² in the voltage range 2.3-4.6 V. The reversible capacity after 100 cycles is more than 190 mAh g⁻¹ at room temperature.     

Spray-drying synthesized LiNi0.6Co0.2Mn0.2O2 and its electrochemical performance as cathode materials for lithium ion batteries

Layered LiNi_0.6Co_0.2Mn_0.2O₂ materials were synthesized at different sintering temperatures using spray-drying precursor with molar ratio of Li/Me = 1.04 (Me = transition metals). The influences of sintering temperature on crystal structure, morphology and electrochemical performance of LiNi_0.6Co_0.2Mn_0.2O₂ materials have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and charge-discharge test. As a result, material synthesized at 850 °C has excellent electrochemical performance, delivering an initial discharge capacity of 173.1 mAh g^− 1 between 2.8 and 4.3 V at a current density of 16 mA g^− 1 and exhibiting good cycling performance.     

Rapid microwave-assisted synthesis of graphene nanosheet/Co3O4 composite for supercapacitors

Graphene nanosheet (GNS)/Co₃O₄ composite has been rapidly synthesized by microwave-assisted method. Field emission scanning electron microscopy and transmission electron microscopy observation reveals the homogeneous distribution of Co₃O₄ nanoparticles (3-5 nm in size) on graphene sheets. Electrochemical properties are characterized by cyclic voltammetry, galvanostatic charge/discharge and electrochemical impedance spectroscopy. A maximum specific capacitance of 243.2 F g⁻¹ has been obtained at a scan rate of 10 mV s⁻¹ in 6 M KOH aqueous solution for GNS/Co₃O₄ composite. Furthermore, the composite exhibits excellent long cycle life along with ∼95.6% specific capacitance retained after 2000 cycle tests.     

Electrochemical investigation of LiNi0.5Mn1.5O4 thin film intercalation electrodes

This work provides kinetic and transport parameters of Li-ion during its extraction/insertion into thin film LiNi_0.5Mn_1.5O₄ free of binder and conductive additive. Thin films of LiNi_0.5Mn_1.5O₄ (0.2 μm thick) were prepared on electronically conductive gold substrate utilizing the electrostatic spray deposition technique. High purity LiNi_0.5Mn_1.5O₄ thin film electrodes were observed with cyclic voltammetry, to exhibit very sharp peaks, high reversibility, and absence of the 4 V signal related to the Mn³⁺/Mn⁴⁺ redox couple. The electrode subjected to 100 CV cycles of charge/discharge delivered a capacity of 155 mAh g⁻¹ on the first cycle and sustained a good cycling behavior while retaining 91% of the initial capacity after 50 cycles. Kinetics and mass-transport of Li-ion extraction at LiNi_0.5Mn_1.5O₄ thin film electrode were investigated by means of electrochemical impedance spectroscopy. The apparent chemical diffusion coefficient (D_app) value determined from EIS measurements changed depending on the electrode potential in the range of 10⁻¹⁰-10⁻¹² cm² s⁻¹. The D_app profile shows two minimums at the potential values close to the peak potentials of the corresponding cyclic voltammogram.     

Effect of fluorine in the preparation of Li(Ni1/3Co1/3Mn1/3)O2 via hydroxide co-precipitation

Uniform and spherical Li(Ni_1/3Co_1/3Mn_1/3)O_(2−δ)F_δ powders were synthesized via NH₃ and F⁻ coordination hydroxide co-precipitation. The effect of F⁻ coordination agent on the morphology, structure and electrochemical properties of the Li(Ni_1/3Co_1/3Mn_1/3)O_(2−δ)F_δ were studied. The morphology, size, and distribution of (Ni_1/3Co_1/3Mn_1/3)(OH)_(2−δ)F_δ particle diameter were improved in a shorter reaction time through the addition of F⁻. The study suggested that the added F improves the layered characteristics of the lattice and the cyclic performance of Li(Ni_1/3Co_1/3Mn_1/3)O₂ in the voltage range of 2.8-4.6 V. The initial capacity of the Li(Ni_1/3Co_1/3Mn_1/3)O_1.96F_0.04 was 178 mAh g⁻¹, the maximum capacity was 186 mAh g⁻¹ and the capacity after 50 cycles was 179 mAh g⁻¹ in the voltage range of 2.8-4.6 V.     

Synthesis of compounds, Li(MMn11/6)O4 (M = Mn1/6, Co1/6, (Co1/12Cr1/12), (Co1/12Al1/12), (Cr1/12Al1/12)) by polymer precursor method and its electrochemical performance for lithium-ion batteries

The compounds, Li(MMn_11/6)O₄ (M = Mn_1/6, Co_1/6, (Co_1/12Cr_1/12), (Co_1/12Al_1/12), (Cr_1/12Al_1/12)) are synthesised by the polymer precursor method. The structure and the morphology of the compounds are studied by the Rietveld refined X-ray diffraction (XRD), and transmission electron microscopy (TEM) techniques, respectively. Density and the Brunauer, Emmet and Teller surface area (BET) of the compounds are also studied. The cobalt doped compound, Li(Co_1/6Mn_11/6)O₄ is found to be nanosized particles in the range of 60-100 nm, when compared to the other compounds in our present study. The oxidation state and the local structure of the compounds are analysed by the X-ray absorption spectroscopy (XAS) technique. Cyclic voltammetry (CV) and the galvanostatic charge-discharge cycling (30 mA g⁻¹) studies are made in the voltage range of 3.5-4.3 V at room temperature for all the compounds under study. The bare and (Co_1/6), and (Co_1/12Cr_1/12) substituted spinels are cycled at high current rates of 1, 2 and 5C (assuming 1C∼120 mA g⁻¹). Cycling results of Co-substituted spinels show better and long-term capacity retention at all the current rates. At the end of the second cycle, Li(Co_1/6Mn_11/6)O₄ compound delivers a discharge capacity value of 100 (±3) and 87 (±3) mAh g⁻¹ for the current rate of 2 and 5C, respectively. An excellent capacity retention value of 94% is observed at the end of the 1000 cycles for both 2 and 5C rates.     

Synthesis of spinel LiMn2O4 with manganese carbonate prepared by micro-emulsion method

Micro-spherical particle of MnCO₃ has been successfully synthesized in CTAB-C₈H₁₈-C₄H₉OH-H₂O micro-emulsion system. Mn₂O₃ decomposed from the MnCO₃ is mixed with Li₂CO₃ and sintered at 800 °C for 12 h, and the pure spinel LiMn₂O₄ in sub-micrometer size is obtained. The LiMn₂O₄ has initial discharge specific capacity of 124 mAh g⁻¹ at discharge current of 120 mA g⁻¹ between 3 and 4.2 V, and retains 118 mAh g⁻¹ after 110 cycles. High-rate capability test shows that even at a current density of 16 C, capacity about 103 mAh g⁻¹ is delivered, whose power is 57 times of that at 0.2 C. The capacity loss rate at 55 °C is 0.27% per cycle.     

Mn3O4 nanoparticles embedded into graphene nanosheets: Preparation, characterization, and electrochemical properties for supercapacitors

Mn₃O₄/graphene nanocomposites were synthesized by mixing graphene suspension in ethylene glycol with MnO₂ organosol, followed by subsequent ultrasonication processing and heat treatment. The as-prepared product consists of nanosized Mn₃O₄ particles homogeneously distributed on graphene nanosheets, which has been confirmed by field emission scanning electron microscopy and transmission electron microscopy analysis. Atomic force microscope analysis further identified the distribution of dense Mn₃O₄ nanoparticles on graphene nanosheets. When used as electrode materials in supercapacitors, Mn₃O₄/graphene nanocomposites exhibited a high specific capacitance of 175 F g⁻¹ in 1 M Na₂SO₄ electrolyte and 256 F g⁻¹ in 6 M KOH electrolyte, respectively. The enhanced supercapacitance of Mn₃O₄/graphene nanocomposites could be ascribed to both electrochemical contributions of Mn₃O₄ nanoparticles, functional groups attached to graphene nanosheets, and significantly increased specific surface area.     

Enhanced electrochemical performances of LiNi0.5Mn1.5O4 spinel via ethylene glycol-assisted synthesis

A simple and effective method, ethylene glycol-assisted co-precipitation method, has been employed to synthesize LiNi_0.5Mn_1.5O₄ spinel. As a chelating agent, ethylene glycol can realize the homogenous distributions of metal ions at the atomic scale and prevent the growth of LiNi_0.5Mn_1.5O₄ particles. XRD reveals that the prepared material is a pure-phase cubic spinel structure (Fd3m) without any impurities. SEM images show that it has an agglomerate structure with the primary particle size of less than 100 nm. Electrochemical tests demonstrate that the as-prepared LiNi_0.5Mn_1.5O₄ possesses high capacity and excellent rate capability. At 0.1 C rate, it shows a discharge capacity of 137 mAh g⁻¹ which is about 93.4% of the theoretical capacity (146.7 mAh g⁻¹). At the high rate of 5 C, it can still deliver a discharge capacity of 117 mAh g⁻¹ with excellent capacity retention rate of more than 95% after 50 cycles. These results show that the as-prepared LiNi_0.5Mn_1.5O₄ is a promising cathode material for high power Li-ion batteries.     

Highly reversible Co3O4/graphene hybrid anode for lithium rechargeable batteries

A Co₃O₄/graphene hybrid material was fabricated using a simple in situ reduction process and demonstrated as a highly reversible anode for lithium rechargeable batteries. The hybrid is composed of 5 nm size Co₃O₄ particles uniformly dispersed on graphene, as observed by transmission electron microscopy, atomic force microscopy, Raman spectroscopy and X-ray diffraction analysis. The Co₃O₄/graphene anode can deliver a capacity of more than 800 mA h g⁻¹ reversibly at a 200 mA g⁻¹ rate in the voltage range between 3.0 and 0.001 V. The high reversible capacity is retained at elevated current densities. At a current rate as high as 1000 mA g⁻¹, the Co₃O₄/graphene anode can deliver more than 550 mA h g ⁻¹, which is significantly higher than the capacity of current commercial graphite anodes. The superior electrochemical performance of the Co₃O₄/graphene is attributed to its unique nanostructure, which intimately combines the conductive graphene network with uniformly dispersed nano Co₃O₄ particles.     

Hydrothermal preparation of octadecahedron Fe3O4 thin film for use in an electrochemical supercapacitor

A Fe₃O₄ film with regularly edge-affected cubic (octadecahedron) morphology was successfully prepared on stainless steel foil by a simple and benign hydrothermal process. The potential for the use of the film in a supercapacitor was tested by investigating the electrochemical behavior of the Fe₃O₄ film using cyclic voltammetry (CV) and galvanostatic charge/discharge tests. The Fe₃O₄ film showed a CV indicative of a typical pseudocapactive behavior in 1 mol L⁻¹ Na₂SO₃ solution. Furthermore, this film exhibited a specific capacitance of 118.2 F g⁻¹ at the current of 6 mA between −1 and 0.1 V with a capacity retention of 88.75% after 500 cycles.     

Electrochemical properties of bare and Ta-substituted Nb2O5 nanostructures

In this work, bare and Ta-substituted Nb₂O₅ nanofibers are prepared by electrospinning followed by sintering at temperatures in the 800–1100 °C range for 1 h in air. Obtained bare and Ta-substituted Nb₂O₅ polymorphs are characterized by X-ray diffraction, scanning electron microscopy, density measurement, and Brunauer, Emmett and Teller surface area. Electrochemical properties are evaluated by cyclic voltammetry and galvanostatic techniques. Cycling performance of Nb₂O₅ structures prepared at temperature 800 °C, 900 °C, and 1100 °C shows following discharge capacity at the end of 10th cycle: 123, 140, and 164 (±3) mAh g⁻¹, respectively, in the voltage range 1.2–3.0 V and at current rate of 150 mA g⁻¹ (1.5 C rate). Heat treated composite electrode based on M-Nb₂O₅ (1100 °C) in argon atmosphere at 220 °C, shows an improved discharge capacity of 192 (±3) mAh g⁻¹ at the end of 10th cycle. The discharge capacity of Ta-substituted Nb₂O₅ prepared at 900 °C and 1100 °C showed a reversible capacity of 150, 202 (±3) mAh g⁻¹, respectively, in the voltage range 1.2–3.0 V and at current rate of 150 mA g⁻¹. Anodic electrochemical properties of M-Nb₂O₅ deliver a reversible capacity of 382 (±5) mAh g⁻¹ at the end of 25th cycle and Ta-substituted Nb₂O₅ prepared at 900 °C, 1000 °C and 1100 °C shows a reversible capacity of 205, 130 and 200 (±3) mAh g⁻¹ (at 25th cycle) in the range, 0.005–2.6 V, at current rate of 100 mA g⁻¹.     

Soft template synthesis of mesoporous Co3O4/RuO2·xH2O composites for electrochemical capacitors

Co₃O₄/RuO₂·xH₂O composites with various Ru content (molar content of Ru = 5%, 10%, 20%, 50%) were synthesized by one-step co-precipitation method. The precursors were prepared via adjusting pH of the mixed aqueous solutions of Co(NO₃)₂·6H₂O and RuCl₃·0.5H₂O by using Pluronic123 as a soft template. For the composite with molar ratio of Co:Ru = 1:1 annealed at 200 °C, Brunauer-Emmet-Teller (BET) results indicated that the composite showed mesoporous structure, and the specific surface area of the composite was as high as 107 m² g⁻¹. The electrochemical performances of these composites were measured in 1 M KOH electrolyte. Compared with the composite prepared without template, the composite with P123 exhibited a higher specific capacitance. When the molar content of Ru was rising, the specific capacitance of the composites increased significantly. It was also observed that the crystalline structures as well as the electrochemical activities were strongly dependent on the annealing temperature. A capacitance of 642 F/g was obtained for the composite (Co:Ru = 1:1) annealed at 150 °C. Meanwhile, the composites also exhibited good cycle stability. Besides, the morphologies and textural characteristic of the samples were also investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM).     

Enhanced cycling performance of Fe3O4-graphene nanocomposite as an anode material for lithium-ion batteries

Fe₃O₄-graphene nanocomposite was prepared by a gas/liquid interface reaction. The structure and morphology of the Fe₃O₄-graphene nanocomposite were characterized by X-ray diffraction, scanning electron microscopy and high-resolution transmission electron microscopy. The electrochemical performances were evaluated in coin-type cells. Electrochemical tests show that the Fe₃O₄-22.7 wt.% graphene nanocomposite exhibits much higher capacity retention with a large reversible specific capacity of 1048 mAh g⁻¹ (99% of the initial reversible specific capacity) at the 90th cycle in comparison with that of the bare Fe₃O₄ nanoparticles (only 226 mAh g⁻¹ at the 34th cycle). The enhanced cycling performance can be attributed to the facts that the graphene sheets distributed between the Fe₃O₄ nanoparticles can prevent the aggregation of the Fe₃O₄ nanoparticles, and the Fe₃O₄-graphene nanocomposite can provide buffering spaces against the volume changes of Fe₃O₄ nanoparticles during electrochemical cycling.