Nb2O5 as efficient and recyclable photocatalyst for indigo carmine degradation

Heterogeneous photocatalysis is a significant green technology for application in water purification. The application of Nb₂O₅ catalyst for the photodegradation of contaminants is few reported in the literature. Thus, the Nb₂O₅ catalyst was characterized by SEM, FTIR, surface area and charge surface density. This catalyst was applied to degrade indigo carmine dye, which was compared with degradation catalyzed by TiO₂ and ZnO. Almost 100% of dye degradation occurred at 20, 45 and 90 min for TiO₂, ZnO and Nb₂O₅, respectively. The effect of Nb₂O₅ catalyst concentration, pH and ionic strength (μ) was investigated. The Nb₂O₅ activity increased at 0.7 g/L and for higher catalyst concentrations the degradation was kept constant. Degradation of indigo carmine dye catalyzed by Nb₂O₅ was improved at pH < 4.0 and μ = 0.05 mol/L. TiO₂, ZnO and Nb₂O₅ were recovered and re-applied in other nine reaction cycles. While TiO₂ and ZnO have an abrupt loss of their catalytic activity, Nb₂O₅ maintained 85% of catalytic activity after 10 reaction cycles.     

Investigation on electrochemical reduction process of Nb2O5 powder in molten CaCl2 with metallic cavity electrode

The direct electrochemical reduction process of Nb₂O₅ powder was investigated by cyclic voltammetry and constant potential electrolysis with a novel metallic cavity electrode in molten calcium chloride at 850 °C. The products of both constant potential and constant voltage electrolysis were characterized by XRD, SEM and EDX. CaNb₂O₆ was formed upon addition of solid Nb₂O₅ into molten CaCl₂ when CaO was present. During the electrolysis solid Nb₂O₅ was reduced to various niobium oxides of lower oxidation states, including some composite oxides, and then was converted completely to metallic niobium near −0.35 V (vs. Ag/AgCl), which was more positive than the reduction potential of Ca²⁺. Constant potential electrolysis was applied at the potentials near the reduction current peaks derived from the cyclic voltammetry curves, and cell voltages were monitored. The voltage was near 2.4 V when the oxide was metallized at −0.35 V (vs. Ag/AgCl). Nb₂O₅ pellet could be used to prepared metallic niobium at cell voltage 2.4 V in a larger electrolysis bath filled with calcium chloride at 850 °C. The experiment results further demonstrated the direct electrochemical reduction mechanism of Nb₂O₅ powder in a molten system.     

The catalytic performance in oxidative coupling of methane and the surface basicity of La2O3, Nd2O3, ZrO2 and Nb2O5

The catalytic performance in oxidative coupling of methane (OCM) of unmodified pure La₂O₃, Nd₂O₃, ZrO₂ and Nb₂O₅ has been investigated under various conditions. The results confirmed that the activity of La₂O₃ and Nd₂O₃ was always much higher than that of the remaining two. The surface basicity/base strength distribution of pure La₂O₃, Nd₂O₃, ZrO₂ and Nb₂O₅ was measured using a test reaction of transformation of 2-butanol and a temperature-programmed desorption of CO₂. Both methods showed that La₂O₃ and Nd₂O₃ had high basicity and contained medium and strong basic sites (lanthanum oxide more and neodymium oxide somewhat less). ZrO₂ had only negligible amount of weak basic sites and Nb₂O₅ was rather acidic. The confrontation of the basicity and catalytic performance indicated that in the case of investigated oxides, the basicity (especially strong basic sites) could be a decisive factor in determination of the catalytic activity in OCM. Only in the case of ZrO₂ it was observed a moderate catalytic performance in spite of negligible basicity. The influence of a gas atmosphere used in the calcination of oxides (flowing oxygen, helium and nitrogen) on their basicity and catalytic activity in OCM had been also investigated. Contrary to earlier observations with MgO, no effect of calcination atmosphere on the catalytic performance of investigated oxides in OCM and on their basicity was observed.     

Effect of an Nb2O5 nanolayer coating on ZnO electrodes in dye-sensitized solar cells

Nanostructured porous zinc oxide electrodes for use in dye-sensitized solar cells (DSSCs) were coated with thin niobium oxide layers by using sol–gel transformation of niobium pentaethoxide in air. Coating solutions were prepared by mixing niobium pentaethoxide and ethanol. A dip-coating technique was adopted at a low withdrawal speed of 100 μm s⁻¹. The coated electrodes were then heat-treated at temperatures between 400 and 600 °C. The presence of niobium in the coated electrodes was confirmed by X-ray photoelectron spectroscopy. As expected, the niobium oxide layers worked as an energy barrier between the ZnO electrode and electrolyte. Open-circuit voltage (V_OC) of the cells using the coated electrodes was then enhanced up to 0.768 V, which was attributable to the suppression of the recombination of photogenerated electrons with oxidized species in electrolytes. An additional benefit of the coating was that grain growth of ZnO particles in the electrodes was hindered and short-circuit photocurrent density (J_SC) was kept relatively high due to large amounts of adsorbed dye. An overall light-to-electricity conversion efficiency was increased to a maximum of 5.19%, indicating that the proper coating technique was the key for improving the performance of ZnO-based DSSCs.     

XANES study of polyaniline-V2O5 and sulfonated polyaniline-V2O5 nanocomposites

In this work, two materials for secondary lithium battery cathodes formed by polyaniline-V₂O₅ and sulfonated polyaniline-V₂O₅, which have a higher charge capacity than the V₂O₅ xerogel, were synthesized. X-ray absorption and Fourier transform infrared spectroscopies were employed to analyze the short-range interactions in these materials. Based on these experiments, it was possible to observe significant differences in the symmetry of the VO₅ units, and this was attributed to the intimate contact between V₂O₅ and the polymers, and to some flexibility of the VO₅ square pyramids due to the low range order of the nanocomposites.     

Mixed oxides Ca2Fe2O5 and Ca2Co2O5 as anode materials for Li-ion batteries

The electrochemical performance of mixed oxides, Ca₂Fe₂O₅ and Ca₂Co₂O₅ for use in Li-ion batteries was studied with Li as the counter electrode. The compounds were prepared and characterized by X-ray diffraction and SEM. Ca₂Fe₂O₅ showed a reversible capacity of 226 mAh/g at the 14th cycle and retained 183 mAh/g at the end of 50 cycles at 60 mA/g in the voltage window 0.005-2.5 V. A reversible capacity in the range, 365-380 mAh/g, which is stable up to 50 charge-discharge cycles is exhibited by Ca₂Co₂O₅ in the voltage window, 0.005-3.0 V and at 60 mA/g. This corresponds to recycleable moles of Li of 3.9±0.1 (theoretical: 4.0). Significant improvement in the cycling performance and attainable reversible capacity were noted for Ca₂Co₂O₅ on cycling to an upper cut-off voltage of 3.0 V as compared to 2.5 V. Coulombic efficiency for both compounds is >98%. Electrochemical impedance spectroscopy (EIS) data clearly indicate the reversible formation/decomposition of polymeric surface film on the electrode surface of Ca₂Co₂O₅ in the voltage window, 0.005-3.0 V. Cyclic voltammetry results compliment the galvanostatic cycling data.     

Electrochemical properties of microwave irradiated synthesis of poly(3,4-ethylenedioxythiophene)/V2O5 nanocomposites as cathode materials for rechargeable lithium batteries

A series of poly(3,4-ethylenedioxythiophene) (PEDOT)/V₂O₅ nanocomposites are prepared via the redox intercalative polymerization reaction of 3,4-ethylenedioxythiophene (EDOT) monomer and crystalline V₂O₅ within 10 min by using rapid 2.45 GHz microwave irradiation with full power (800 W). The unique properties of the resultant nanocomposites are investigated by various characterization techniques using powder XRD, TGA/DTA and four-point probe conductivity analysis supports the intercalation of polymer nanosheet between V₂O₅ layers leading to enhanced bi-dimensionality. X-ray photoelectron spectroscopy analysis clearly shows the presence of mixed valent V⁴⁺/V⁵⁺ in the V₂O₅ framework after the redox intercalative polymerization which also confirms charge transfer from the polymer to the V₂O₅ framework. The application potential of these composites as cathode materials in rechargeable lithium batteries is also demonstrated by the electrochemical intercalation of lithium into the PEDOT/V₂O₅ nanocomposites, where an enhancement in the discharge capacity (370 mAh/g) is observed compared to that of crystalline V₂O₅.     

Study of ruthenium supported on Ta2O5–ZrO2 and Nb2O5–ZrO2 as catalysts for the partial oxidation of methane

Ru-based catalysts supported on Ta₂O₅–ZrO₂ and Nb₂O₅–ZrO₂ are studied in the partial oxidation of methane at 673–873 K. Supports with different Ta₂O₅ or Nb₂O₅ content were prepared by a sol–gel method, and RuCl₃ and RuNO(NO₃)₃ were used as precursors to prepare the catalysts (ca. 2 wt.% Ru). At 673 K high selectivity to CO₂ was found. An increase of temperature up to 773 K produced an increase in the selectivity to syngas (H₂/CO = 2.2–3.1), and this is related with the transformation of RuO₂ to metallic Ru as was determined from XRD and XPS results. At 873 K and with co-fed CO₂ an increase of the catalytic activity and CO selectivity was found. A TOF value of 5.7 s⁻¹ and H₂/CO ratio ca. 1 was achieved over Ru(Cl)/6TaZr. Catalytic results are discussed as a function of the support composition and characteristics of Ru-based phases.     

Synthesis of compounds, Li(MMn11/6)O4 (M = Mn1/6, Co1/6, (Co1/12Cr1/12), (Co1/12Al1/12), (Cr1/12Al1/12)) by polymer precursor method and its electrochemical performance for lithium-ion batteries

The compounds, Li(MMn_11/6)O₄ (M = Mn_1/6, Co_1/6, (Co_1/12Cr_1/12), (Co_1/12Al_1/12), (Cr_1/12Al_1/12)) are synthesised by the polymer precursor method. The structure and the morphology of the compounds are studied by the Rietveld refined X-ray diffraction (XRD), and transmission electron microscopy (TEM) techniques, respectively. Density and the Brunauer, Emmet and Teller surface area (BET) of the compounds are also studied. The cobalt doped compound, Li(Co_1/6Mn_11/6)O₄ is found to be nanosized particles in the range of 60-100 nm, when compared to the other compounds in our present study. The oxidation state and the local structure of the compounds are analysed by the X-ray absorption spectroscopy (XAS) technique. Cyclic voltammetry (CV) and the galvanostatic charge-discharge cycling (30 mA g⁻¹) studies are made in the voltage range of 3.5-4.3 V at room temperature for all the compounds under study. The bare and (Co_1/6), and (Co_1/12Cr_1/12) substituted spinels are cycled at high current rates of 1, 2 and 5C (assuming 1C∼120 mA g⁻¹). Cycling results of Co-substituted spinels show better and long-term capacity retention at all the current rates. At the end of the second cycle, Li(Co_1/6Mn_11/6)O₄ compound delivers a discharge capacity value of 100 (±3) and 87 (±3) mAh g⁻¹ for the current rate of 2 and 5C, respectively. An excellent capacity retention value of 94% is observed at the end of the 1000 cycles for both 2 and 5C rates.     

Long-term degradation of Ta2O5-doped Bi2O3 systems

Bismuth oxide in δ-phase is a well-known high oxygen ion conductor and can be used as an electrolyte for intermediate temperature solid oxide fuel cells (IT-SOFCs). 5-10 mol% Ta₂O₅ are doped into Bi₂O₃ to stabilize δ-phase by solid state reaction process. One Bi₂O₃ sample (7.5TSB) was stabilized by 7.5 mol% Ta₂O₅ and exhibited single phase δ-Bi₂O₃-like (type I) phase. Thermo-mechanical analyzer (TMA), X-ray diffractometry (XRD), AC impedance and high-resolution transmission electron microscopy (HRTEM) were used to characterize the properties. The results showed that holding at 800-850 °C for 1 h was the appropriate sintering conditions to get dense samples. Obvious conductivity degradation phenomenon was obtained by 1000 h long-term treatment at 650 °C due to the formation of α-Bi₂O₃ phase and Bi₃TaO₇, and 〈1 1 1〉 vacancy ordering in Bi₃TaO₇ structure.     

SO2 and NO removal from flue gas over V2O5/AC at lower temperatures — role of V2O5 on SO2 removal

Supporting V₂O₅ onto an activated coke (AC) has been reported to significantly increase the AC's activity in simultaneous SO₂ and NO removal from flue gas. To understand the role of V₂O₅ on SO₂ removal, V₂O₅/AC is studied through SO₂ removal reaction, surface analysis, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FTIR) techniques. It is found that the main role of V₂O₅ in SO₂ removal over V₂O₅/AC is to catalyze SO₂ oxidation through a VOSO₄-like intermediate species, which reacts with O₂ to form SO₃ and V₂O₅. The SO₃ formed transfers from the V sites to AC sites and then reacts with H₂O to form H₂SO₄. At low V₂O₅ loadings, a V atom is able to catalyze as many as 8 SO₂ molecules to SO₃. At high V₂O₅ loadings, however, the number of SO₂ molecules catalyzed by a V atom is much less, due possibly to excessive amounts of V₂O₅ sites in comparison to the pores available for SO₃ and H₂SO₄ storage.     

Low-temperature firing and microwave dielectric properties of 16CaO–9Li2O–12Sm2O3–63TiO2 ceramics with V2O5 addition

The sintering behaviors and microwave dielectric properties of the 16CaO–9Li₂O–12Sm₂O₃–63TiO₂ (abbreviated CLST) ceramics with different amounts of V₂O₅ addition had been investigated in this paper. The sintering temperature of the CLST ceramic had been efficiently decreased by nearly 100 °C. No secondary phase was observed in the CLST ceramics and complete solid solution of the complex perovskite phase was confirmed. The CLST ceramics with small amounts of V₂O₅ addition could be well sintered at 1200 °C for 3 h without much degradation in the microwave dielectric properties. Especially, the 0.75 wt.% V₂O₅-doped ceramics sintered at 1200 °C for 3 h have optimum microwave dielectric properties of Kr = 100.4, Q × f = 5600 GHz, and TCF = 7 ppm/°C. Obviously, V₂O₅ could be a suitable sintering aid that improves densification and microwave dielectric properties of the CLST ceramics.     

Electrochemical properties of carbon-coated CaWO4 versus Li

Carbon-coated CaWO₄ nano-crystalline phases have been synthesized by ambient temperature solution precipitation method, characterized by X-ray diffraction, SEM and thermogravimetry and their electrochemical properties were studied versus Li metal. Galvanostatic cycling at a current of 60 mA/g in the voltage range 0.005-3.0 V on the 5 wt.% C-coated CaWO₄ gave a reversible capacity of 230 ± 5 mAh/g corresponding to 2.5 mol of Li, which is almost stable from 20 to 50 cycles. Under the same conditions, the 10 wt.% C-coated CaWO₄ showed a capacity of 355 ± 5 mAh/g (3.8 mol of Li) during the initial cycles, but the capacity degraded at a rate of 1.6 mAh/g per cycle in the range 5-100 cycles. A good operating voltage range was found to be 0.005-3.0 V with average discharge and charge potentials being 0.6 and 1.3 V, respectively. Coulombic efficiency in all cases was 96-98%. Cyclic voltammograms compliment the galvanostatic results. Impedance spectral data on the 10 wt.% C-coated CaWO₄ at different voltages during the first and 20th discharge-charge cycle have been interpreted in terms of the variations in the bulk and charge-transfer resistances of the composite electrode. A reaction mechanism involving the formation/decomposition of the oxide bronze, ‘Li_xWO_y’ has been proposed to explain the electrochemical cycling.     

Corrosion mechanisms of Al2O3/MgAl2O4 by V2O5, NiO, Fe2O3 and vanadium slag

The effects of V₂O₅, NiO, Fe₂O₃ and vanadium slag on the corrosion of Al₂O₃ and MgAl₂O₄ have been investigated. The specimens of Al₂O₃ and MgAl₂O₄ with the respective oxides above mentioned were heated at 10 °C/min from room temperature up to three different temperatures: 1400, 1450 and 1500 °C. The corrosion mechanisms of each system were followed by XRD and SEM analyses. The results obtained showed that Al₂O₃ was less affected by the studied oxides than MgAl₂O₄. Alumina was only attacked by NiO forming NiAl₂O₄ spinel, while the MgAl₂O₄ spinel was attacked by V₂O₅ forming MgV₂O₆. It was also observed that Fe₂O₃ and Mg, Ni, V and Fe present in the vanadium slag diffused into Al₂O₃. On the other hand, the Fe₂O₃ and Ca, S, Si, Na, Mg, V and Fe diffused into the MgAl₂O₄ structure. Finally, the results obtained were compared with those predicted by the FactSage software.     

Electrochemical preparation and characterization of V2O5/polyaniline composite film cathodes for Li battery

Vanadium pentoxide/polyaniline (V₂O₅/PANi) composite films were prepared by a two-step electrochemical method and evaluated for their application in lithium batteries. As a first step the PANi film was potentiodynamically grown in an acid solution containing aniline monomer, and secondly vanadium oxide was oxidatively deposited on the polyaniline film in a temperature controlled VOSO₄ solution. The increased current efficiency obtained with the larger anodic current in the high temperature solutions results in high contents of V₂O₅ in the composites, even if the oxidative dissolution of PANi also occurs. The large value of the diffusion coefficient estimated from the cyclic voltammograms for the composite film provides evidence for the synergistic effect of the conducting polymer and the inorganic composite. The cell exhibited excellent cycle stability with a high charge storage capacity. The large increase in the specific capacity for the composite film prepared in this work demonstrates that the conducting polymer in the composite acts as a binding and conducting element by contributing its electroactivity. The V₂O₅/PANi composite film cathodes show a large specific capacity (ca. 270 mAh/g) and improved cyclability with an extremely small amount of capacity fading (ca. 3.4%) during repeated charge/discharge cycles.     

Preparation of columbite MgNb2O6 and ZnNb2O6 ceramics by reaction-sintering

Columbite MgNb₂O₆ (MN) and ZnNb₂O₆ (ZN) ceramics produced by the reaction-sintering process were investigated. Secondary phases Mg_0.652Nb_0.598O_2.25 and Mg_0.66Nb_11.33O₂₉ were found in MgNb₂O₆ pellets. After 1250 °C sintering for 2 h, a density 4.85 g/cm³ (97.1% of the theoretical value) was obtained in MgNb₂O₆ pellets. In ZnNb₂O₆ pellets, no secondary phase formed. The maximum density 5.55 g/cm³ (98.7% of the theoretical value) occurs at 1200 and 1180 °C sintering for 2 and 4 h, respectively.     

Effect of Cr dopant on the cathodic behavior of LiCoO2

Compounds of the formula LiCo_1−yCr_yO₂ (0.0≤y≤0.20 and y=1.0) have been synthesized by high temperature solid-state reaction and were characterized by XRD and FT-IR. Hexagonal a and c lattice parameters increase with increasing y as expected from ionic size effects. Cyclic voltammograms reveal that the phase transformation occurring at x=0.5 in Li_1−x(Co_1−yCr_y)O₂ is suppressed for y=0.05 and 0.10. Low-current (0.01 C; 1 C=140 mA g⁻¹) galvanostatic charging curves show that the deintercalation voltage for y=0.05 and 0.10 decrease for a given x as compared to LiCoO₂. Galvanostatic charge-discharge cycling of the Li(Co_1−yCr_y)O₂ cathodes at 0.14 C and 2.7-4.3 V (vs. Li) show that increasing amount of chromium content in the LiCoO₂ lattice drastically reduces the amount of Li that can be reversibly cycled. Ex-situ XRD of the cycled cathodes show that slight cation-mixing occurs in the layered structure for y=0.05 and 0.10 and could be the reason for their poor electrochemical performance. Reversible Li intercalation/deintercalation is not possible in LiCrO₂ in the voltage range 2.7-4.3 V.     

Enhanced electrochemical performance and thermal stability of La2O3-coated LiCoO2

An enhanced electrochemical performance LiCoO₂ cathode was synthesized by coating with various wt.% of La₂O₃ to the LiCoO₂ particle surfaces by a polymeric method, followed by calcination at 923 K for 4 h in air. The surface-coated materials were characterized by XRD, TGA, SEM, TEM, BET and XPS/ESCA techniques. XRD patterns of La₂O₃-coated LiCoO₂ revealed that the coating did not affect the crystal structure, α-NaFeO₂, of the cathode material compared to pristine LiCoO₂. TEM images showed a compact coating layer on the surface of the core material that had an average thickness of about ∼15 nm. XPS data illustrated that the presence of two different environmental O 1s ions corresponds to the surface-coated La₂O₃ and core material. The electrochemical performance of the coated materials by galvanostatic cycling studies suggest that 2.0 wt.% coated La₂O₃ on LiCoO₂ improved cycle stability (284 cycles) by a factor of ∼7 times over the pristine LiCoO₂ cathode material and also demonstrated excellent cell cycle stability when charged at high voltages (4.4, 4.5 and 4.6 V). Impedance spectroscopy demonstrated that the enhanced performance of the coated materials is attributed to slower impedance growth during the charge-discharge processes. The DSC curve revealed that the exothermic peak corresponding to the release of oxygen at ∼464 K was significantly smaller for the La₂O₃-coated cathode material and recognized its high thermal stability.     

Gas-phase elemental mercury capture by a V2O5/AC catalyst

Gas-phase elemental mercury (Hg⁰) capture by an activated coke (AC) supported V₂O₅ (V₂O₅/AC) catalyst was studied in simulated flue gas and compared with that by the AC. The study on the influences of V₂O₅ loading, temperature, capture time and flue gas components (O₂, SO₂, H₂O and N₂) shows that the Hg⁰ capture capability of V₂O₅/AC is much higher than that of AC. It increases with an increase in V₂O₅ loading and is promoted by O₂, which indicates the important role of V₂O₅ in Hg⁰ oxidation and capture; it is promoted slightly by SO₂ but inhibited by H₂O; it increases with an increase in temperature up to 150 °C when Hg desorption starts. X-ray photoelectron spectroscopy analysis and sequential chemical extraction experiments indicate that the main states of Hg captured on V₂O₅/AC are HgO and HgSO₄. Temperature programmed desorption experiments were also made to understand the stability of the Hg captured.     

Electrochemical investigation of LiMn2O4 cathodes in gel electrolyte at various temperatures

A composite lithium battery electrode of LiMn₂O₄ in combination with a gel electrolyte (1 M LiBF₄/24 wt% PMMA/1:1 EC:DEC) has been investigated by galvanostatic cycling experiments and electrochemical impedance spectroscopy (EIS) at various temperatures, i.e. −3<T<56 °C. For analysis of EIS data, a mathematical model taking into account local kinetics and potential distribution in the liquid phase within the porous electrode structure was used. Reasonable values of the double-layer capacitance, the exchange-current density and the solid phase diffusion were found as a function of temperature. The apparent activation energy of the charge-transfer (∼65 kJ mol⁻¹), the solid phase transfer (∼45 kJ mol⁻¹) and of the ionic bulk and effective conductance in the gel phase (∼34 kJ mol⁻¹), respectively, were also determined. The kinetic results related to ambient temperature were compared to those obtained in the corresponding liquid electrolyte. The incorporated PMMA was found to reduce the ionic conductivity of the free electrolyte, and it was concluded that the presence of 24 wt% PMMA does not have a significant influence on the kinetic properties of LiMn₂O₄.