Electrochemical properties of bare and Ta-substituted Nb2O5 nanostructures

In this work, bare and Ta-substituted Nb₂O₅ nanofibers are prepared by electrospinning followed by sintering at temperatures in the 800–1100 °C range for 1 h in air. Obtained bare and Ta-substituted Nb₂O₅ polymorphs are characterized by X-ray diffraction, scanning electron microscopy, density measurement, and Brunauer, Emmett and Teller surface area. Electrochemical properties are evaluated by cyclic voltammetry and galvanostatic techniques. Cycling performance of Nb₂O₅ structures prepared at temperature 800 °C, 900 °C, and 1100 °C shows following discharge capacity at the end of 10th cycle: 123, 140, and 164 (±3) mAh g⁻¹, respectively, in the voltage range 1.2–3.0 V and at current rate of 150 mA g⁻¹ (1.5 C rate). Heat treated composite electrode based on M-Nb₂O₅ (1100 °C) in argon atmosphere at 220 °C, shows an improved discharge capacity of 192 (±3) mAh g⁻¹ at the end of 10th cycle. The discharge capacity of Ta-substituted Nb₂O₅ prepared at 900 °C and 1100 °C showed a reversible capacity of 150, 202 (±3) mAh g⁻¹, respectively, in the voltage range 1.2–3.0 V and at current rate of 150 mA g⁻¹. Anodic electrochemical properties of M-Nb₂O₅ deliver a reversible capacity of 382 (±5) mAh g⁻¹ at the end of 25th cycle and Ta-substituted Nb₂O₅ prepared at 900 °C, 1000 °C and 1100 °C shows a reversible capacity of 205, 130 and 200 (±3) mAh g⁻¹ (at 25th cycle) in the range, 0.005–2.6 V, at current rate of 100 mA g⁻¹.     

Synthesis and electrochemical characterization of LiCoxMn1−xPO4/C nanocomposites

LiCo_xMn_1−xPO₄/C nanocomposites (0 ≤ x ≤ 1.0) were prepared by a combination of spray pyrolysis at 300 °C and wet ball-milling followed by heat treatment at 500 °C for 4 h in 3% H₂ + N₂ atmosphere. X-ray diffraction analysis indicated that all samples had the single phase olivine structures indexed by orthorhombic Pmna. The lattice parameters linearly decreased with increasing cobalt content, which confirmed the existence of solid solutions. It was clearly seen from the scanning electron microscopy observation that the LiCo_xMn_1−xPO₄/C samples were agglomerates with approximately 100 nm primary particles. The LiCo_xMn_1−xPO₄/C nanocomposites were used as cathode materials for lithium batteries, and electrochemical performance was comparatively investigated with cyclic voltammetry and galvanostatic charge–discharge test using the Li?1 M LiPF₆ in EC:DMC = 1:1?LiCo_xMn_1−xPO₄/C cells at room temperature. The cells at 0.05 C charge–discharge rate delivered first discharge capacities of 165 mAh g⁻¹ (96% of theoretical capacity) at x = 0, 136 mAh g⁻¹ at x = 0.2, 132 mAh g⁻¹ at x = 0.5, 125 mAh g⁻¹ at x = 0.8 and 132 mAh g⁻¹ (79% of theoretical capacity) at x = 1.0, respectively. While the first discharge capacity increased with the cobalt content at high charge–discharge rates more than 0.5 C due to higher electronic conductivity of LiCoPO₄ in comparison with LiMnPO₄, the cycleability of cell became worse with increasing the amount of cobalt. The existence of Mn²⁺ seemed to enhance the cycleability of LiCo_xMn_1−xPO₄/C nanocomposite cathode.     

Hydrothermal synthesis of LiMn2O4/C composite as a cathode for rechargeable lithium-ion battery with excellent rate capability

A spinel LiMn₂O₄/C composite was synthesized by hydrothermally treating a precursor of manganese oxide/carbon (MO/C) composite in 0.1 M LiOH solution at 180 °C for 24 h, where the precursor was prepared by reducing potassium permanganate with acetylene black (AB). The AB in the precursor serves as the reducing agent to synthesize the LiMn₂O₄ during the hydrothermal process; the excess of AB remains in the hydrothermal product, forming the LiMn₂O₄/C composite, where the remaining AB helps to improve the electronic conductivity of the composite. The contact between LiMn₂O₄ and C in our composite is better than that in the physically mixed LiMn₂O₄/C material. The electrochemical performance of the LiMn₂O₄/C composite was investigated; the material delivered a high capacity of 83 mAh g⁻¹ and remained 92% of its initial capacity after 200 cycles at a current density of 2 A g⁻¹, indicating its excellent rate capability as well as good cyclic performance.     

Electrochemical properties of SnO2/carbon composite materials as anode material for lithium-ion batteries

SnO₂/carbon composite anode materials were synthesized from SnCl₄·5H₂O and sucrose via a hydrothermal route and a post heat-treatment. The synthesized spherical SnO₂/carbon powders show a cauliflower-like micro-sized structure. High annealing temperature results in partial reduction of SnO₂. Metallic Sn starts to emerge at 500 °C. High Sn content in SnO₂/carbon composite is favorable for the increase of initial coulombic efficiency but not for the cycling stability. The SnO₂/carbon annealed at 500 °C exhibits high specific capacity (∼400 mAh g⁻¹), stable cycling performance and good rate capability. The generation of Li₂O in the first lithiation process can prevent the aggregation of active Sn, while the carbon component can buffer the big volume change caused by lithiation/delithiation of active Sn. Both of them make contribution to the better cycle stability.     

A large capacity of LiV3O8 cathode material for rechargeable lithium-based batteries

A cathode material, LiV₃O₈, for rechargeable lithium-based batteries has been prepared via a combined freeze-drying method and appropriately post-treated in argon atmosphere. It was found that the sample post-treated at 300 °C in Ar has the optimal performance. Electrochemical tests performed on this material demonstrated its very high insertion capacity of 347 mAh g⁻¹ (3.7 Li⁺ per LiV₃O₈) at a current density of 50 mA g⁻¹ (C/6). Most important is that it displayed an excellent cycling stability and after 60 cycles, a discharge capacity with 351 mAh g⁻¹ was obtained. It was proposed that a short-range crystallographic order had a stronger influence on the electrochemical performance of an electrode material in this work, instead of the surface area, particle size and crystalline degree, etc.     

Properties of Li-graphite and LiFePO4 electrodes in LiPF6–sulfolane electrolyte

Sulfolane (also referred to as tetramethylene sulfone, TMS) containing LiPF₆ and vinylene carbonate (VC) was tested as a non-flammable electrolyte for a graphite |LiFePO₄ lithium-ion battery. Charging/discharging capacity of the LiFePO₄ electrode was ca. 150 mAh g⁻¹ (VC content 5 wt%). The capacity of the graphite electrode after 10 cycles establishes at the level of ca. 350 mAh g⁻¹ (C/10 rate). In the case of the full graphite |1 M LiPF₆ + TMS + VC 10 wt% |LiFePO₄ cell, both charging and discharging capacity (referred to cathode mass) stabilized at a value of ca. 120 mAh g⁻¹. Exchange current density for Li⁺ reduction on metallic lithium, estimated from electrochemical impedance spectroscopy (EIS) experiments, was j_o(Li/Li⁺) = 8.15 × 10⁻⁴ A cm⁻². Moreover, EIS suggests formation of the solid electrolyte interface (SEI) on lithium, lithiated graphite and LiFePO₄ electrodes, protecting them from further corrosion in contact with the liquid electrolyte. Scanning electron microscopy (SEM) images of pristine electrodes and those taken after electrochemical cycling showed changes which may be interpreted as a result of SEI formation. No graphite exfoliation was observed. The main decomposition peak of the LiPF₆ + TMS + VC electrolyte (TG/DTA experiment) was present at ca. 275 °C. The LiFePO₄(solid) + 1 M LiPF₆ + TMS + 10 wt% VC system shows a flash point of ca. 150 °C. This was much higher in comparison to that characteristic of a classical LiFePO₄ (solid) + 1 M LiPF₆ + 50 wt% EC + 50 wt% DMC system (T_f ≈ 37 °C).     

Synthesis of LiFePO4/C by solid-liquid reaction milling method

LiFePO₄/C was synthesized by the method of solid-liquid reaction milling, using FeCl₃·6H₂O, Li₂CO₃ and (NH₄)₂HPO₄ and glucose, which was used as reductant (carbon source). The samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), TG-DTA analysis, infrared absorption carbon-sulfur analysis and electrochemical performance test. The sample synthesized at 680 °C for 8 h showed, at initial discharge, a capacity of 155.8, 153.2, 148.5, 132.7 mAh g^− 1 at 0.2 °C, 0.5 °C, 1 °C and 3 °C rate respectively. The sample also showed an excellent capacity retention as there was no significant capacity fade after 10 cycles.     

Synthesis and electrochemical performance of Li2FeSiO4/carbon/carbon nano-tubes for lithium ion battery

Li₂FeSiO₄/carbon/carbon nano-tubes (Li₂FeSiO₄/C/CNTs) and Li₂FeSiO₄/carbon (Li₂FeSiO₄/C) composites were synthesized by a traditional solid-state reaction method and characterized comparatively by X-ray diffraction, scanning electron microscopy, BET surface area measurement, galvanostatic charge-discharge and AC impedance spectroscopy, respectively. The results revealed that the Li₂FeSiO₄/C/CNT composite exhibited much better rate performance in comparison with the Li₂FeSiO₄/C composite. At 0.2 C, 5 C and 10 C, the former composite electrode delivered a discharge capacity of 142 mAh g⁻¹, 95 mAh g⁻¹, 80 mAh g⁻¹, respectively, and after 100 cycles at 1 C, the discharge capacity remained 95.1% of its initial value.     

Cathodic performance of LiMn1−xMxPO4 (M = Ti, Mg and Zr) annealed in an inert atmosphere

To improve the cathodic performance of olivine-type LiMnPO₄, we investigated the optimal annealing conditions for a composite of carbon with cation doping. Nanocrystalline and the cation-doped LiMn_1−xM_xPO₄ (M = Ti, Mg, Zr and x = 0, 0.01, 0.05 and 0.10) was synthesized in aqueous solution using a planetary ball mill. The synthesis was performed at the fairly low temperature of 350 °C to limit particle size. The obtained samples except for the Zr doped one consisted of uniform and nano-sized particles. The performance of LiMnPO₄ was much improved by an annealing treatment between 500 and 550 °C with carbon in an inert atmosphere. A small amount of metal-rich phosphide (Mn₂P) was detected in the sample annealed at 900 °C. In addition, 1 at.% Mg doping for Fe enhanced the rate capability in our doped samples. The discharge capacity of LiMn_0.99Mg_0.01PO₄/C was 146 mAh/g at 0.1 mA/cm² and 125 mAh/g even at 2.0 mA/cm².     

Electrochemical performance of Li3V2(PO4)3/C cathode materials using stearic acid as a carbon source

The Li₃V₂(PO₄)₃/C cathode materials are synthesized by a simple solid-state reaction process using stearic acid as both reduction agent and carbon source. Scanning electron microscopy and transmission electron microscopy observations show that the Li₃V₂(PO₄)₃/C composite synthesized at 700 °C has uniform particle size distribution and fine carbon coating. The Li₃V₂(PO₄)₃/C shows a high initial discharge capacity of 130.6 and 124.4 mAh g⁻¹ between 3.0 and 4.3 V, and 185.9 and 140.9 mAh g⁻¹ between 3.0 and 4.8 V at 0.1 and 5 C, respectively. Even at a charge–discharge rate of 15 C, the Li₃V₂(PO₄)₃/C still can deliver a discharge capacity of 103.3 and 112.1 mAh g⁻¹ in the potential region of 3.0–4.3 V and 3.0–4.8 V, respectively. Based on the analysis of cyclic voltammograms and electrochemical impedance spectra, the apparent diffusion coefficients of Li ions in the composites are in the region of 1.09 × 10⁻⁹ and 4.95 × 10⁻⁸ cm² s⁻¹.     

Electrochemical performance of single crystalline spinel LiMn2O4 nanowires in an aqueous LiNO3 solution

Single crystalline cubic spinel LiMn₂O₄ nanowires were synthesized by hydrothermal method and the precursor calcinations. The phase structures and morphologies were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and high-resolution transmission electron microscopy (HRTEM). Galvanostatic charging/discharging cycles of as-prepared LiMn₂O₄ nanowires were performed in an aqueous LiNO₃ solution. The initial discharge capacity of LiMn₂O₄ nanowires was 110 mAh g⁻¹, and the discharge capacity was still above 100 mAh g⁻¹ after 56 cycles at 10C-rate, and then 72 mAh g⁻¹ was registered after 130 cycles. This is the first report of a successful use of single crystalline spinel LiMn₂O₄ nanowire as cathode material for the aqueous rechargeable lithium battery (ARLB).     

Emulsion drying synthesis of olivine LiFePO4/C composite and its electrochemical properties as lithium intercalation material

The electroactive LiFePO₄/C nano-composite has been synthesized by an emulsion drying method. During burning-out the oily emulsion precipitates in an air-limited atmosphere at 300 °C, amorphous or low crystalline carbon was generated along with releasing carbon oxide gases, and trivalent iron as a cheap starting material was immediately reduced to the divalent one at this stage as confirmed by X-ray photoelectron spectroscopy, leading to a low crystalline LiFePO₄/C composite. Heat-treatment of the low crystalline LiFePO₄/C in an Ar atmosphere resulted in a well-ordered olivine structure, as refined by Rietveld refinement of the X-ray diffraction pattern. From secondary electron microscopic and scanning transmission electron microscopic observations with the corresponding elemental mapping images of iron and phosphorous, it was found that the LiFePO₄ powders are modified by fine carbon. The in situ formation of the nano-sized carbon during crystallization of LiFePO₄ brought about two advantages: (i) an optimized particle size of LiFePO₄, and (ii) a uniform distribution of fine carbon in the product. These effects of the fine carbon on LiFePO₄/C composite led to high capacity retention upon cycling at 25 and 50 °C and high rate capability, resulting from a great enhancement of electric conductivity as high as 10⁻⁴ S cm⁻¹. That is, the obtained capacity was higher than 90 mAh (g-phosphate)⁻¹ by applying a higher current density of about 1000 mA g⁻¹ (11 C) at 50 °C.     

Preparation and characterization of core–shell structure Fe3O4/C nanoparticles with unique stability and high electrochemical performance for lithium-ion battery anode material

Core–shell structure carbon coating Fe₃O₄ nanoparticles are prepared by a two-step method. The crystalline structure and the electrochemical performance of the prepared samples are investigated. The results indicate that a uniform and continuous carbon layer is formed on the surface of Fe₃O₄ nanoparticles. The core–shell structure Fe₃O₄/C nanoparticles show a high initial discharge capacity of 1546 mAh g⁻¹ and a specific stable discharge capacity of about 800 mAh g⁻¹ at 0.5 C with no noticeable capacity fading up to 100 cycles.     

Synthesis of spinel LiMn2O4 with manganese carbonate prepared by micro-emulsion method

Micro-spherical particle of MnCO₃ has been successfully synthesized in CTAB-C₈H₁₈-C₄H₉OH-H₂O micro-emulsion system. Mn₂O₃ decomposed from the MnCO₃ is mixed with Li₂CO₃ and sintered at 800 °C for 12 h, and the pure spinel LiMn₂O₄ in sub-micrometer size is obtained. The LiMn₂O₄ has initial discharge specific capacity of 124 mAh g⁻¹ at discharge current of 120 mA g⁻¹ between 3 and 4.2 V, and retains 118 mAh g⁻¹ after 110 cycles. High-rate capability test shows that even at a current density of 16 C, capacity about 103 mAh g⁻¹ is delivered, whose power is 57 times of that at 0.2 C. The capacity loss rate at 55 °C is 0.27% per cycle.     

Effects of carbon source and carbon content on electrochemical performances of Li4Ti5O12/C prepared by one-step solid-state reaction

Li₄Ti₅O₁₂/C composites were synthesized by one-step solid-state reaction method using four commonly used organic compounds or organic polymers as carbon source, i.e., polyacrylate acid (PAA), citric acid (CA), maleic acid (MA) and polyvinyl alcohol (PVA). The physical characteristics of Li₄Ti₅O₁₂/C composites were investigated by X-ray diffraction, electron microscopy, Raman spectroscopy, particle size distribution and thermogravimetry-derivative thermogravimetry techniques. Their electrochemical properties were characterized by cyclic voltammograms, electrochemical impedance spectra, constant current charge–discharge and rate charge–discharge. These analyses indicated that the carbon source and carbon content have a great effect on the physical and electrochemical performances of Li₄Ti₅O₁₂/C composites. An ideal carbon source and appropriate carbon content effectively improved the electrical contact between the Li₄Ti₅O₁₂ particles, which enhanced the discharge capacity and rate capability of Li₄Ti₅O₁₂/C composites. PAA was the best carbon source for the synthesis of Li₄Ti₅O₁₂/C composites. When the carbon content was 3.49 wt.% (LiOH·H₂O/PAA molar ratio of 1), as-prepared Li₄Ti₅O₁₂/C showed the maximum discharge capacity. At 0.2 C, initial capacity of the optimized sample was 168.6 mAh g⁻¹ with capacity loss of 2.8% after 50 cycles. At 8 and 10 C, it showed discharge capacities of 143.5 and 132.7 mAh g⁻¹, with capacity loss of 8.7 and 9.9% after 50 cycles, respectively.     

Core–shell Ni0.5TiOPO4/C composites as anode materials in Li ion batteries

Pristine Ni_0.5TiOPO₄ was prepared via a traditional solid-state reaction, and then Ni_0.5TiOPO₄/C composites with core–shell nanostructures were synthesized by hydrothermally treating Ni_0.5TiOPO₄ in glucose solution. X-ray diffraction patterns indicate that Ni_0.5TiOPO₄/C crystallizes in monoclinic P2₁/c space group. Scanning electron microscopy and transmission electron microscopy show that the small particles with different sizes are coated with uniform carbon film of ∼3 nm in thickness. Raman spectroscopy also confirms the presence of carbon in the composites. Ni_0.5TiOPO₄/C composites presented a capacity of 276 mAh g⁻¹ after 30 cycles at the current density of 42.7 mA g⁻¹, much higher than that of pristine Ni_0.5TiOPO₄ (155 mAh g⁻¹). The improved electrochemical performances can be attributed to the existence of carbon shell.     

High reversible capacity of SnO2/graphene nanocomposite as an anode material for lithium-ion batteries

A gas–liquid interfacial synthesis approach has been developed to prepare SnO₂/graphene nanocomposite. The as-prepared nanocomposite was characterized by X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy, and Brunauer–Emmett–Teller measurements. Field emission scanning electron microscopy and transmission electron microscopy observation revealed the homogeneous distribution of SnO₂ nanoparticles (2–6 nm in size) on graphene matrix. The electrochemical performances were evaluated by using coin-type cells versus metallic lithium. The SnO₂/graphene nanocomposite prepared by the gas–liquid interface reaction exhibits a high reversible specific capacity of 1304 mAh g⁻¹ at a current density of 100 mA g⁻¹ and excellent rate capability, even at a high current density of 1000 mA g⁻¹, the reversible capacity was still as high as 748 mAh g⁻¹. The electrochemical test results show that the SnO₂/graphene nanocomposite prepared by the gas–liquid interfacial synthesis approach is a promising anode material for lithium-ion batteries.     

Synthesis of highly crystalline spinel LiMn2O4 by a soft chemical route and its electrochemical performance

Highly crystalline spinel LiMn₂O₄ was successfully synthesized by annealing lithiated MnO₂ at a relative low temperature of 600 °C, in which the lithiated MnO₂ was prepared by chemical lithiation of the electrolytic manganese dioxide (EMD) and LiI. The LiI/MnO₂ ratio and the annealing temperature were optimized to obtain the pure phase LiMn₂O₄. With the LiI/MnO₂ molar ratio of 0.75, and annealing temperature of 600 °C, the resulting compounds showed a high initial discharge capacity of 127 mAh g⁻¹ at a current rate of 40 mAh g⁻¹. Moreover, it exhibited excellent cycling and high rate capability, maintaining 90% of its initial capacity after 100 charge-discharge cycles, at a discharge rate of 5 C, it kept more than 85% of the reversible capacity compared with that of 0.1 C.     

Electrochemical performance of the carbon coated Li3V2(PO4)3 cathode material synthesized by a sol-gel method

A carbon coated Li₃V₂(PO₄)₃ cathode material for lithium ion batteries was synthesized by a sol-gel method using V₂O₅, H₂O₂, NH₄H₂PO₄, LiOH and citric acid as starting materials, and its physicochemical properties were investigated using X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) spectroscopy, scanning electron microscopy (SEM), energy dispersive analysis of X-ray (EDAX), transmission electron microscope (TEM), and electrochemical methods. The sample prepared displays a monoclinic structure with a space group of P2₁/n, and its surface is covered with a rough and porous carbon layer. In the voltage range of 3.0-4.3 V, the Li₃V₂(PO₄)₃ electrode displays a large reversible capacity, good rate capability and excellent cyclic stability at both 25 and 55 °C. The largest reversible capacity of 130 mAh g⁻¹ was obtained at 0.1C and 55 °C, nearly equivalent to the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹). It was found that the increase in total carbon content can improve the discharge performance of the Li₃V₂(PO₄)₃ electrode. In the voltage range of 3.0-4.8 V, the extraction and reinsertion of the third lithium ion in the carbon coated Li₃V₂(PO₄)₃ host are almost reversible, exhibiting a reversible capacity of 177 mAh g⁻¹ and good cyclic performance. The reasons for the excellent electrochemical performance of the carbon coated Li₃V₂(PO₄)₃ cathode material were also discussed.     

X-ray photoelectron spectroscopy and electrochemical behaviour of 4 V cathode, Li(Ni1/2Mn1/2)O2

Layered Li(Ni_1/2Mn_1/2)O₂ was prepared by the solution and mixed hydroxide methods, characterised by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) and studied by cyclic voltammetry (CV) and charge discharge cycling in CC and CCCV modes at room temperature (r.t.) and at 50 °C. The XPS studies show about 8% of Ni³⁺ and Mn³⁺ ions are present in Li(Ni²⁺_1/2Mn_1/2⁴⁺)O₂ due to valency-degeneracy. The compound prepared at 950 °C, 12 h, solution method gives a second cycle discharge capacity of 150 mA h g⁻¹ (2.5-4.4 V) at a specific current of 30 mA g⁻¹ and retains 137 mA h g⁻¹ at the end of 40 cycles. CV shows that the redox process at 3.7-4.0 V corresponds to Ni²⁺↔Ni⁴⁺ and clear indication of Mn^3+/4+ couple was noted at 4.2-4.5 V. The observed capacity-fading (2.5-4.4 V) is shown to be contributed by the polarisation at the end of charging. The cathodic capacity is stable up to 40 cycles in the voltage window, 2.5-4.2 V both at room temperature and 50 °C.