Low temperature preparation of a high performance Pt/SWCNT counter electrode for flexible dye-sensitized solar cells

A platinum/single-wall carbon nanotube (Pt/SWCNT) film was sprayed onto a flexible indium-doped tin oxide coated polyethylene naphthalate (ITO/PEN) substrate to form a counter electrode for use in a flexible dye-sensitized solar cell using a vacuum thermal decomposition method at low temperature (120 °C). The obtained Pt/SWCNT electrode showed good chemical stability and light transmittance and had lower charge transfer resistance and higher electrocatalytic activity for the I₃⁻/I⁻ redox reaction compared to the flexible Pt electrode or a commercial Pt/Ti electrode. The light-to-electric energy conversion efficiency of the flexible DSSC based on the Pt/SWCNT/ITO/PEN counter electrode and the TiO₂/Ti photoanode reached 5.96% under irradiation with a simulated solar light intensity of 100 mW cm⁻². The efficiency was increased by 25.74% compared to the flexible DSSC with an unmodified Pt counter electrode.     

Ionic liquid–polymer electrolyte for amperometric solid-state NO2 sensor

A new ionic liquid–polymer electrolyte was successfully tested in the planar amperometric solid-state sensor sensitive towards nitrogen dioxide. The electrolyte consists of 1-butyl-3-methylimidazolium hexafluorophosphate (BMIPF₆) and poly(ethylene glycol) methyl ether methacrylate (PEGMEMA) in the ratio 57:43 mol.% and exhibits ionic conductivity 1.6 × 10⁻⁴ S cm⁻¹ at 20 °C, high electrochemical stability (over 4 V on gold or glassy carbon) and thermal stability (over 230 °C). The analyte, gaseous nitrogen dioxide in air, was determined using the electrochemical reduction at −900 mV vs. Pt/air on gold minigrid indicating electrode with Pt/air as a reference electrode. The sensor response is linear in the NO₂ concentration range 0.3–1.1 ppm and is reproducible and long-term stable.     

Enhanced performance of a dye-sensitized solar cell with a modified poly(3,4-ethylenedioxythiophene)/TiO2/FTO counter electrode

ClO₄⁻-poly(3,4-ethylenedioxythiophene)/TiO₂/FTO (ClO₄⁻-PEDOT/TiO₂/FTO) counter electrode (CE) in dye-sensitized solar cells (DSSCs) is fabricated by using an electrochemical deposition method. Comparing with the DSSCs with ClO₄⁻-PEDOT/FTO counter electrode, the photocurrent-voltage (I-V) measurement reveals that the photocurrent conversion efficiency (η), fill factor (FF) and short-circuit current density (J_SC) of DSSCs with a ClO₄⁻-PEDOT/TiO₂/FTO CE increase. The enhanced performances of the DSSCs are attributed to the higher J_SC arising from the increase of active surface area of ClO₄⁻-PEDOT/TiO₂/FTO CE. Electrochemical impedance spectra (EIS) also indicate that the charge-transfer resistance on the ClO₄⁻-PEDOT/electrolyte interface decreases. Cyclic voltammetry results indicate that the ClO₄⁻-PEDOT/TiO₂/FTO electrode shows higher activity towards I₃⁻/I⁻ redox reaction than that of ClO₄⁻-PEDOT/FTO electrode.     

New mechanism of gas transport at the interface solid/liquid

It was recently shown that an abnormally fast transport of CO molecules takes place at the electrode/electrolyte interface of Pt and PtRu electrodes in H₂SO₄ and HClO₄ solutions. In the present paper, this phenomenon is tested for other gases, such as hydrogen and oxygen. The fast transport is also observed at the solid/electrolyte solution interface of other electrode materials and at the glass/electrolyte interface. Several experiments are shown, demonstrating that mass transfer takes place at a velocity, which is more than one order of magnitude higher than expected for usual diffusion conditions.Assuming radial mass transfer at the interface of a Pt disc, the activation energy, E_a = 23 kJ mol⁻¹, was calculated from Arrhenius plots. The same value was measured in H₂SO₄ and HClO₄ as supporting electrolytes. The mass transport parameter, Y, at 298 K was 4.8 × 10⁻³ cm² s⁻¹ and 2.9 × 10⁻³ cm² s⁻¹ in 0.5 M H₂SO₄ and 1 M HClO₄ respectively.     

Promoting Effect of Layered Titanium Phosphate on the Electrochemical and Photovoltaic Performance of Dye-Sensitized Solar Cells

We reported a composite electrolyte prepared by incorporating layered α-titanium phosphate (α-TiP) into an iodide-based electrolyte using 1-ethyl-3-methylimidazolium tetrafluoroborate(EmimBF₄) ionic liquid as solvent. The obtained composite electrolyte exhibited excellent electrochemical and photovoltaic properties compared to pure ionic liquid electrolyte. Both the diffusion coefficient of triiodide (I₃ ⁻) in the electrolyte and the charge-transfer reaction at the electrode/electrolyte interface were improved markedly. The mechanism for the enhanced electrochemical properties of the composite electrolyte was discussed. The highest conversion efficiency of dye-sensitized solar cell (DSSC) was obtained for the composite electrolyte containing 1wt% α-TiP, with an improvement of 58% in the conversion efficiency than the blank one, which offered a broad prospect for the fabrication of stable DSSCs with a high conversion efficiency.     

The electrochemical reduction of oxygen on zinc corrosion films in alkaline solutions

Kinetics of the O₂ reduction has been characterized on Zn corrosion films by Pt/Zn rotating ring-disc electrode (RRDE) and EIS methods. On zinc-oxide films a two-step reduction was identified in various buffer solutions of pH 10.5, while a small quantity of H₂O₂ intermediate could be detected. On the basis of results obtained from Pt/Zn and Pt/Pt RRDE experiments in solutions containing H₂O₂, it was further confirmed that the HO₂⁻ was reduced to OH⁻ through the zinc-oxide corrosion layer. Capacitance data of the zinc-oxide/electrolyte interface calculated from steady-state impedance diagrams measured at various cathodic potentials indicate the presence of a space charge layer of the semi-metallic ZnO. The solid-state reaction mechanism of HO₂⁻ disproportion with participation of Zn_i⁺ interstitials, oxygen ion vacancies of the non-stoichiometric Zn-oxide, and chemisorbed HO₂⁻ is discussed.     

Simulations and study of electrochemical hydrogen energy conversion in EasyTest Cell

An EasyTest Cell concept is applied to study the performance characteristics of the electrochemical processor for polymer electrolyte membrane electrochemical hydrogen energy converters (PEM EHEC), broadly known as a membrane electrode assembly (MEA). A series of MEAs consisting of Nafion 117 polymer electrolyte and magnetron sputtered Pt, IrO_x, and composite IrO_x/Pt/IrO_x catalysts with varying catalytic loadings were investigated. The partial electrode reactions proceeding in the real PEM EHEC, namely hydrogen oxidation (HOR), hydrogen evolution (HER), oxygen reduction (ORR), and oxygen evolution (OER), are simulated and studied in a recently developed test cell with a unitized gas compartment. The EasyTest Cell design gives possibilities for strict control of the experimental conditions by avoiding the usage of any auxilliary gas conditioning equipment. By varying the thickness of the sputtered Pt film, the catalyst loading is remarkably reduced (from 0.5 to 0.06 mg cm⁻² or about 8 times) for both HOR and HER without any sacrifice of the electrode performance. The electrode with 0.2 mg cm⁻² sputtered IrO_x shows the best OER performance. The composite IrO_x/Pt/IrO_x electrode demonstrated a bi-functional catalytic activity toward both OER and ORR, as well as improved gas diffusion properties toward ORR compared to the single Pt layer with the same catalytic loading.A phenomenological criterion for evaluating the gas diffusion properties of the electrodes is proposed. The applied testing approach is validated via comparison of the results obtained in the EasyTestCell and the common laboratory PEM electrolytic cell.     

Kinetics of the SCN/(SCN)2 couple on platinum in acetonitrile

The electrode kinetics of the SCN⁻/(SCN)₂ system has been studied on platinum in the temperature range from −12 to −3°C at different ammonium thiocyanate concentrations in acetonitrile in the presence of 0·1 M [(C₂H₅)₄N]ClO₄. Quasi-steady E/I curves with a Pt rotating disk electrode and E/I curves at different linear potential-sweep rates were recorded under different experimental conditions.     

Iodide/triiodide electrochemistry in ionic liquids: Effect of viscosity on mass transport, voltammetry and scanning electrochemical microscopy

The electrochemistry of I⁻/I₃⁻ was studied in ionic liquids using a combination of cyclic voltammetry, chronoamperometry and scanning electrochemical microscopy (SECM). The electrolytes were 1-alkyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide [C_nC₁Im][Tf₂N], ionic liquids (where n = 2, 4 and 8) and I⁻ was typically added at a concentration of approximately 11 mM. During cyclic voltammetry, two sets of peaks were observed in each ionic liquid due to oxidation and reduction of the I⁻/I₃⁻ redox couple and oxidation/reduction of the I₃⁻/I₂ redox couple. The diffusion coefficients of I⁻ and I₃⁻, as determined using chronoamperometry, increased with increasing temperature and decreased with increasing ionic liquid viscosity. The effect of ionic liquid viscosity on ultramicroelectrode (UME) voltammetry was also determined using the I⁻/I₃⁻ redox couple. Steady-state behaviour was observed at 1.3 μm UMEs at slow voltammetric scan rates and steady-state SECM feedback approach curves were also obtained at a 1.3 μm Pt SECM tips, provided that the tip approach speed was sufficiently low.     

CO2 attraction by specifically adsorbed anions and subsequent accelerated electrochemical reduction

The electrochemical reduction of CO₂ was studied on a copper mesh electrode in aqueous solutions containing 3 M solutions of KCl, KBr and KI as the electrolytes in a two and three phase configurations. Electrochemical experiments were carried out in a laboratory-made, divided H-type cell. The working electrode was a copper mesh, while the counter and reference electrodes were Pt wire and Ag/AgCl electrode, respectively. Results of our work suggest a reaction mechanism for the electrochemical reduction of CO₂ in the two phase configuration where the presence of Cu-X as the catalytic layer facilitates the electron transfer from the electrode to CO₂. Electron-transfer to CO₂ may occur via the X_ad⁻(Br⁻, Cl⁻, I⁻)-C bond, which is formed by the electron flow from the specifically adsorbed halide anion to the vacant orbital of CO₂. The stronger the adsorption of the halide anion to the electrode, the more strongly CO₂ is restrained, resulting in higher CO₂ reduction current. Furthermore, it is suggested that specifically adsorbed halide anions could suppress the adsorption of protons, leading to a higher hydrogen overvoltage. These effects may synergistically mitigate the overpotential necessary for CO₂ reduction, and thus increase the rate of electrochemical CO₂ reduction.     

The physical–chemical properties and electrocatalytic performance of iridium oxide in oxygen evolution

An IrO₂ anode catalyst was prepared by using the Adams method for the application of a solid polymer electrolyte (SPE) water electrolyzer. The effect of calcination temperature on the physical–chemical properties and the electrochemical performance of IrO₂ were examined to obtain a low loading and a high catalytic activity of oxygen evolution at the electrode. The physical–chemical properties were studied via thermogravimetry–differential scanning calorimetry (TG–DSC), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The electrochemical activity was investigated by using cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and chronopotentiometry in 0.1 mol L⁻¹ H₂SO₄ at room temperature. The optimum condition was found to be at the calcination temperature of 500 °C, where the total polarization reached a minimum at high current densities (>200 mA cm⁻²). The optimized catalyst was also applied to a membrane electrode assembly (MEA) and stationary current–potential relationships were investigated. With an optimized catalytic IrO₂ loading of 1.5 mg cm⁻² and a 40% Pt/C loading of 0.5 mg cm⁻², the terminal applied potential difference was 1.72 V at 2 A cm⁻² and 80 °C in a SPE water electrolysis cell.     

Effects of electrolyte in dye-sensitized solar cells and evaluation by impedance spectroscopy

Effects of the electrolyte of DSCs on impedance spectra were evaluated by changing concentration of redox couple, viscosity, and additives to electrolyte. The relation with current-voltage characteristics (I-V characteristics) was investigated. In many cases, the impedance component attributed to charge transfer at TiO₂|electrolyte interface demonstrated strong relation with the I-V characteristics. The recombination of electrons in TiO₂ with I₃⁻ in electrolyte was a key factor in determining performance of DSCs. To evaluate the effect of I₃⁻, diffusion-limiting current in the electrolyte for various viscosities was evaluated by cyclic voltammetry. When the short circuit current (SCC) was almost equal to the diffusion-limiting current, strong influence of the diffusion coefficient on the impedance spectra was observed: impedance arcs were enlarged as the diffusion coefficient was decreased. On the other hand, when the diffusion-limiting current was larger than the SCC, photo-excitation and electron injection processes became dominating factors in the DSCs performance. The SCC was regulated by the charge recombination process at TiO₂|electrolyte interface, and thus the impedance component ω₃ was related to the performance in such condition.     

Effect of microstructure on the electrochemical behavior of Pt/YSZ electrodes

Two types of O₂,Pt/YSZ electrode preparation (Pt/YSZ cermet and sputtered platinum film) have been characterized by SEM and by cyclic voltammetry and chronoamperometry at 450 °C in 20 kPa oxygen. Cyclic voltammetry on the cermet and on the as-sputtered non-porous film electrode evidenced the characteristics of the PtO _x /Pt couple. The corresponding redox reaction occurs at the metal/electrolyte interface and it manifests itself by an anodic wave and one of more cathodic peaks in the voltammogram. Heat treatment of the sputtered electrode at 700 °C in oxygen atmosphere resulted in a porous structure by coalescence of the film. Cyclic voltammetry of the porous film electrode featured the characteristics of the O₂/O²⁻ couple, i.e. the redox reaction of gaseous oxygen occurring at the tpb. Chronoamperometry at anodic potentials showed similar features for both electrode preparations: an initial inhibition, a current peak and a slow activation, the latter being related to the phenomenon of electrochemical promotion of catalysis.     

SFG study on potential-dependent structure of water at Pt electrode/electrolyte solution interface

Structure of water at Pt/electrolyte solution interface was investigated by sum frequency generation (SFG) spectroscopy. Two broad peaks were observed in OH stretching region at ca. 3200 cm⁻¹ and ca. 3400 cm⁻¹, which are known to be due to the symmetric OH stretching (υ₁) of tetrahedrally coordinated, i.e., strongly hydrogen bonded “ice-like” water, and the asymmetric OH stretching (υ₃) of water molecules in a more random arrangement, i.e., weakly hydrogen bonded “liquid-like” water, respectively. The SFG intensity strongly depended on electrode potential. Several possibilities are suggested for the potential dependence of the SFG intensity.     

Electrochemical degradation of Ibuprofen on Ti/Pt/PbO2 and Si/BDD electrodes

The electrochemical oxidation of Ibuprofen (Ibu) was performed using a Ti/Pt/PbO₂ electrode as the anode, prepared according to literature, and a boron doped diamond (BDD) electrode, commercially available at Adamant Technologies. Tests were performed with model solutions of Ibu, with concentrations ranging from 0.22 to 1.75 mM for the Ti/Pt/PbO₂ electrode and 1.75 mM for the BDD electrode, using 0.035 M Na₂SO₄ as the electrolyte, in a batch cell, at different current densities (10, 20 and 30 mA cm⁻²). Absorbance measurements, Chemical Oxygen Demand (COD) and Total Organic Carbon (TOC) tests were conducted for all samples. The results have shown a very good degradation of Ibu, with COD removals between 60 and 95% and TOC removals varying from 48 to 92%, in 6 h experiments, with higher values obtained with the BDD electrode. General Current Efficiency and Mineralization Current Efficiency, determined for both electrodes, show a similar behaviour for 20 mA cm⁻² but a very different one at 30 mA cm⁻². The combustion efficiency was also determined for both anodes, and found to be slightly higher with BDD at lower current density and equal to 100% for both anodes at 30 mA cm⁻².     

Dependence of the electrocatalytic performance of platinized counter electrodes on the redox mediator employed in dye-sensitized solar cells

The electrocatalytic properties of platinized counter electrodes (Pt CEs) prepared by various coating methods were investigated with respect to the redox mediator, including the widely used iodide/tri-iodide (I^?/I ₃ ^? ) and the more recently introduced cobalt(II/III)tris(2,2′-bipyridine) (Co(bpy) ₃ ^2+/3+ ), for application in dye-sensitized solar cells (DSCs). The coating methods controlled Pt loading and the surface morphology of the Pt CEs. For a high-performance DSC with a fill factor >0.7, the charge-transfer resistance at the Pt CE/electrolyte interface should be <4.5 Ω cm² for both redox mediators. The I^?/I ₃ ^? -mediated DSCs were insensitive to Pt loading as low as 0.001 mg cm^?2, while the Co(bpy) ₃ ^2+/3+ -mediated DSCs required relatively large Pt loadings of > 0.005 mg cm^?2. Our results indicated that care should be taken in the preparation of Pt CEs with high transparency and low loading to obtain high-performance DSCs employing cobalt–ligand redox electrolyte.     

Electrochemical characteristics of LSCF-SDC composite cathode for intermediate temperature SOFC

A kind of composite cathode, La_0.58Sr_0.4Co_0.2Fe_0.8O_3−δ-Ce_0.8Sm_0.2O_2−δ (LSCF-SDC), was presented in this paper. The electrochemical performance of the cathode on the electrolyte of SDC and YSZ coated with a thin SDC (YSZ/SDC) layer was studied by electrochemical impedance spectroscopy (EIS) and cathodic polarization techniques for their potential utilization in the intermediate temperature solid oxide fuel cell (IT-SOFC). Also studied was the relationship between the electro-catalytic characteristics and the electrode microstructure. Results showed that the LSCF-SDC composite electrode performed better on the SDC electrolyte than on the electrolyte of YSZ/SDC. The polarization resistance, R_p, of the cathode on the SDC electrolyte was 0.23 Ω cm² at 700 °C and 0.067 Ω cm² at 750 °C, much lower than the corresponding R_p of the same cathode on the YSZ/SDC electrolyte. At 750 °C, the cathodic overpotential of the composite cathode on the SDC electrolyte was 99.7 mV at the current density of 1.0 A cm⁻².     

A novel nickel-based mixed rare-earth oxide/activated carbon supercapacitor using room temperature ionic liquid electrolyte

Mesopore nickel-based mixed rare-earth oxide (NMRO) and activated carbon (AC) with rich oxygen-contained groups were prepared as electrode materials in a supercapacitor using room temperature ionic liquid (RTIL) electrolyte. These electrode materials were characterized by XPS, XRD, N₂ adsorption, SEM as well as various electrochemical techniques, and showed good properties and operated well with RTIL electrolyte. A 3 V asymmetrical supercapacitor was fabricated, which delivered a real power density of 458 W kg⁻¹ as well as a real energy density of 50 Wh kg⁻¹, and during a 500-cycle galvanostatic charge/discharge measurement, no capacity decay was visible. Such promising energy-storage performance was to a large extent ascribed to nonvolatile RTIL electrolyte with wide electrochemical windows and high stable abilities worked with both electrode materials.     

High flash point electrolyte for use in lithium-ion batteries

The high flash point solvent adiponitrile (ADN) was investigated as co-solvent with ethylene carbonate (EC) for use as lithium-ion battery electrolyte. The flash point of this solvent mixture was more than 110 °C higher than that of conventional electrolyte solutions involving volatile linear carbonate components, such as diethyl carbonate (DEC) or dimethyl carbonate (DMC). The electrolyte based on EC:ADN (1:1 wt) with lithium tetrafluoroborate (LiBF₄) displayed a conductivity of 2.6 mS cm⁻¹ and no aluminum corrosion. In addition, it showed higher anodic stability on a Pt electrode than the standard electrolyte 1 M lithium hexafluorophosphate (LiPF₆) in EC:DEC (3:7 wt). Graphite/Li half cells using this electrolyte showed excellent rate capability up to 5C and good cycling stability (more than 98% capacity retention after 50 cycles at 1C). Additionally, the electrolyte was investigated in NCM/Li half cells. The cells were able to reach a capacity of 104 mAh g⁻¹ at 5C and capacity retention of more than 97% after 50 cycles. These results show that an electrolyte with a considerably increased flash point with respect to common electrolyte systems comprising linear carbonates, could be realized without any negative effects on the electrochemical performance in Li-half cells.     

Formation of nanotubes in poly (vinylidene fluoride): Application as solid polymer electrolyte in DSC fabricated using carbon counter electrode

In the present work, we report the incorporation of 2,2′-Azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) diammonium salt (ABTS) in poly(vinylidene fluoride) (PVDF) along with the redox couple (I⁻/I₃⁻). When ABTS, a π-electron donor, is used to dope PVDF, the polymer composite forms brush-like nanotubes and has been successfully used as a solid polymer electrolyte in dye-sensitized solar cells. Under the given conditions, the electrolyte composition forms nanotubes while it is doped with ABTS, a π-electron donor. With this new electrolyte, a dye-sensitized solar cell was fabricated using N3 dye adsorbed over TiO₂ nanoparticles as the photoanode and conducting carbon cement coated FTO as counter electrode.