Nano-CdZr4(PO4)6 as a reusable and robust catalyst for the synthesis of bis-thiazolidinones by a multicomponent reaction of aldehydes,ethylenediamine and thioglycolic acid

Nano-CdZr₄(PO₄)₆ has been used as an efficient catalyst for the preparation of bis-thiazolidinones by pseudo-five-component reaction of aldehydes, ethylenediamine and thioglycolic acid under reflux conditions in toluene. The present synthetic protocol has several advantages, such as simplicity, excellent yields, short reaction times, reusability of the catalyst and low catalyst loading.     

Hydration effects of Al2(MoO4)3 and AlPO4 phases in hydrotreating catalysts studied by solid state nuclear magnetic resonance spectroscopy

Solid state nuclear magnetic resonance spectroscopy of²⁷Al,³¹P, and⁹⁵Mo nuclei was used to investigate species on a NiPMo/Al₂O₃ hydrotreating catalyst calcined at 750 °C before and after rehydration. The Al₂(MoO₄)₃ phase disappeared after rehydration in 100% relative humidity at room temperature. However, almost none of the observed crystalline AlPO₄ reacted with adsorbed water. The results show that the Al₂(MoO₄)₃ phase on an alumina surface reacts easily with moisture unlike Al₂(MoO₄)₃ in the bulk phase. It also suggests that the crystalline AlPO₄ phase is formed under the Al₂(MoO₄)₃ phase or that both species are formed as neighboring islands on the surface of the alumina but have different reactivities toward moisture.     

Effect of ZnSO4, MnSO4 and FeSO4 on the Partial Hydrogenation of Benzene over Nano Ru-Based Catalysts

Nano Ru-based catalysts, including monometallic Ru and Ru-Zn nanoparticles, were synthesized via a precipitation method. The prepared catalysts were evaluated on partial hydrogenation of benzene towards cyclohexene generation, during which the effect of reaction modifiers, i.e., ZnSO₄, MnSO₄, and FeSO₄, was investigated. The fresh and the spent catalysts were thoroughly characterized by XRD, TEM, SEM, XPS, XRF, and DFT studies. It was found that Zn²⁺ or Fe²⁺ could be adsorbed on the surface of a monometallic Ru catalyst, where a stabilized complex could be formed between the cations and the cyclohexene. This led to an enhancement of catalytic selectivity towards cyclohexene. Furthermore, electron transfer was observed from Zn²⁺ or Fe²⁺ to Ru, hindering the catalytic activity towards benzene hydrogenation. In comparison, very few Mn²⁺ cations were adsorbed on the Ru surface, for which no cyclohexene could be detected. On the other hand, for Ru-Zn catalyst, Zn existed as rodlike ZnO. The added ZnSO4 and FeSO₄ could react with ZnO to generate (Zn(OH)₂)₅(ZnSO₄)(H₂O) and basic Fe sulfate, respectively. This further benefited the adsorption of Zn²⁺ or Fe²⁺, leading to the decrease of catalytic activity towards benzene conversion and the increase of selectivity towards cyclohexene synthesis. When 0.57 mol·L⁻¹ of ZnSO₄ was applied, the highest cyclohexene yield of 62.6% was achieved. When MnSO₄ was used as a reaction modifier, H₂SO₄ could be generated in the slurry via its hydrolysis, which reacted with ZnO to form ZnSO₄. The selectivity towards cyclohexene formation was then improved by the adsorbed Zn²⁺.     

Synthesis and Characterization of Nanostructure BPO4

Boron phosphate (BPO₄) is a well known catalyst for a range of organic chemical reactions. In this paper, we report the preparations and characterizations of nano-sized BPO₄ and nano-BPO₄-based core-shell spheres. The samples were synthesized hydrothermally using H₃BO₃, H₃PO₄ and short chain n-alkylamines (n = 3, 4) as starting materials. The resulting products were characterized by powder X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scan electron microscopy (SEM) and transmission electron microscopy (TEM), respectively. A possible mechanism for the formation of the materials is also discussed.     

Nano ZrP2O7 Catalyzed Multicomponent Reaction for an Easy Access of 4H-pyrans and 1,4-dihydropyridines

ZrP₂O₇ nanoparticle catalyzed one-pot synthesis of 4H-pyran scaffolds installing a one-pot three-component coupling reaction of an aldehyde, malononitrile, and ethyl acetoacetate. Also the synthesis of 1,4-dihydropyridines was investigated by using aldehydes, ethyl acetoacetate and ammonium acetate as utilizing nano structured ZrP₂O₇ as an efficient catalyst in ethanol. The attractive features of this process are mild reaction conditions, reusability of the catalyst, short reaction times, easy isolation of the products, and excellent yields.     

Highly efficient complete oxidation of dilute benzene over ultrafine Cu0.1Ce0.5Zr0.4O2−δ catalyst in a fluidized bed reactor

Ultrafine Cu_0.1Ce_0.5Zr_0.4O_2−δ catalyst operated in a fluidized bed reactor was found to be very effective for complete oxidation of dilute benzene in air. The complete conversion of benzene could be achieved at reaction temperature as low as 220 °C. The mechanism of benzene oxidation over the Cu_0.1Ce_0.5Zr_0.4O_2−δ catalyst was investigated by conducting pulse reaction of pure benzene in the absence of O₂ over the catalyst and the results indicated the involvement of lattice oxygen from the catalyst in benzene oxidation.     

A1PO4-Al2O3 catalysts with low alumina content. III. Surface basicity of catalysts obtained in aqueous ammonia

The amount of basic sites of A1PO₄-Al₂O₃ (APA1-A, 5–15 wt% Al₂O₃) catalysts at two basic strengths was measured by studying the liquid-phase adsorption of two acidic molecules (benzoic acid (BA, pK = 4.2) and phenol (PH, pKa = 9.9) from cyclohexane solutions, through the application of a spectrophotometric method. The data obtained follow the Langmuir adsorption isotherm and the monolayer coverage at equilibrium (at 298 K),X _m, is assumed as the amount of basic sites corresponding to the specific pK of the acid used as titrant. The amount of basic sites of any AlPO₄-Al₂O₃ catalyst is higher than that of AlPO₄, but lower than that of Al₂O₃. Besides, an increase in the Al₂O₃ content from 10 wt% gradually increases the basicity of the APA1-A catalyst. Moreover, calcination at increasing temperatures does not practically affect the surface basicity of APAl-A-5 and APAl-A-10 catalysts. However, for AlPO₄ content higher than 10 wt% we observe a decrease in surface basicity, this decrease depends on alumina content, i.e. it is higher as the amount of alumina increases. The basic sites of APAl-A systems catalyze the Knoevenagel condensation ofp-methoxybenzaldehyde and malononitrile at room temperature and in the absence of solvent.     

Preparation and electrochemical performance studies on Cr-doped Li3V2(PO4)3 as cathode materials for lithium-ion batteries

Cr-doped Li₃V_2−xCr_x(PO₄)₃/C (x = 0, 0.05, 0.1, 0.2, 0.5, 1) compounds have been prepared using sol–gel method. The Rietveld refinement results indicate that single-phase Li₃V_2−xCr_x(PO₄)₃/C with monoclinic structure can be obtained. Although the initial specific capacity decreased with Cr content at a lower current rate, both cycle performance and rate capability have excited improvement with moderate Cr-doping content in Li₃V_2−xCr_x(PO₄)₃/C. Li₃V_1.9Cr_0.1(PO₄)₃/C compound presents an initial capacity of 171.4 mAh g⁻¹ and 78.6% capacity retention after 100 cycles at 0.2C rate. At 4C rate, the Li₃V_1.9Cr_0.1(PO₄)₃/C can give an initial capacity of 130.2 mAh g⁻¹ and 10.8% capacity loss after 100 cycles where the Li₃V₂(PO₄)₃/C presents the initial capacity of 127.4 mAh g⁻¹ and capacity loss of 14.9%. Enhanced rate and cyclic capability may be attributed to the optimizing particle size, carbon coating quality, and structural stability during the proper amount of Cr-doping (x = 0.1) in V sites.     

Melamine-(H2SO4)3/melamine-(HNO3)3 instead of H2SO4/HNO3: a safe system for the fast oxidation of thiols and sulfides under solvent-free conditions

Melamine reacted with neat sulfuric acid and fuming nitric acid readily to form two new organic solid acids, namely melamine-(H₂SO₄)₃ and melamine-(HNO₃)₃. Mixture of them acts as a unique powerful system instead of a hazardous H₂SO₄/HNO₃ system for the direct oxidation of thiols. Also, this system can oxidize the sulfides in the presence of a catalytic amount of KBr and few drops of water. This procedure offers advantages such as very low reaction time, simple work-up, excellent yield and matching with some green chemistry protocols.     

Synthesis of sulfides via reaction of aryl/alkyl halides with S8 as a sulfur-transfer reagent catalyzed by Fe3O4-magnetic-nanoparticles-supported L-Histidine-Ni(II)

One-pot synthesis of symmetrical diaryl/alkyl sulfides in high yields from the reaction between aryl/alkyl halides and S₈ can be carried out in a short period, using Fe₃O₄@SiO₂@His@Ni(II) as a reusable catalyst. The present approach offers the advantages of a clean reaction, simple methodology and high efficiency, and avoids the use of a toxic catalyst.     

Nano-CuFe2O4@SO3H Catalyzed Efficient One-Pot Cyclo-Dehydration of Dimedone and Synthesis of Chromeno[4,3-b]chromenes

Chlorosulfonic acid immobilized on CuFe₂O₄ nanoparticles (nano-CuFe₂O₄@SO₃H) was evaluated as a recoverable catalyst for the one-pot cyclo-dehydration of dimedone and synthesis of chromeno[4,3-b]chromene derivatives by reaction of arylaldehydes, dimedone or 1,3-cyclohexanedione, with 3-hydroxycoumarine or 4-hydroxycoumarine in good to excellent yield. Also, 2,2′-Arylmethylene bis(3-hydroxy-5,5-dimethyl-2-cyclohexene-1-one) was synthesized by the reaction of aromatic aldehyde and dimedone using nano-CuFe₂O₄ in ethanol at room temperature. The catalyst could be recycled several times without significant loss of its catalytic activity. Clean methodologies, easy work-up procedure, high yield and simple preparation of the catalyst are some advantages of this procedure.     

Fe3O4@SiO2-SnCl4: An Efficient Catalyst for the Synthesis of Xanthene Derivatives under Ultrasonic Irradiation

Grafting of SnCl₄ on the Fe₃O₄@SiO₂ nanoparticles afforded Fe₃O₄@SiO₂-SnCl₄ as a novel inorganic heterogenous catalyst, which was characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), vibrating sample magnetometry (VSM), Field Emission Scanning Electron Microscopy (FE-SEM), and transmission electron microscopy (TEM). In this research, we report a convenient and efficient direct protocol for the preparation of xanthene derivatives via condensation of β-naphthol, dimedone, or mixture of β-naphthol and dimedone with various aromatic aldehydes in the presence of the catalytic amount of Fe₃O₄@SiO₂-SnCl₄ under ultrasonic irradiation. This procedure has a lot of advantages such as: very easy reaction conditions, absence of any tedious workup, or purification, and much milder method. The corresponding products have been obtained in excellent yields, high purity, and short reaction times.     

Preparation and electrochemical properties of Cr-doped Li9V3(P2O7)3(PO4)2 as cathode materials for lithium-ion batteries

Cr-doped Li₉V_3−xCr_x(P₂O₇)₃(PO₄)₂ (x = 0.0–0.5) compounds have been prepared using sol–gel method. The Rietveld refinement results indicate that single-phase Li₉V_3−xCr_x(P₂O₇)₃(PO₄)₂ (x = 0.0–0.5) with trigonal structure can be obtained. Although the initial specific capacity decreased with Cr content at a lower current rate, both cycle performance and rate capability have excited improvement with moderate Cr-doping content. Li₉V_2.8Cr_0.2(P₂O₇)₃(PO₄)₂ compound presents the good electrochemical rate and cyclic ability. The enhancement of rate and cyclic capability may be attributed to the optimizing particle size, morphologies, and structural stability during the proper amount of Cr-doping (x = 0.2) in V sites.     

Effect of strontium and phosphorus source on the structure,morphology and luminescence of Sr5(PO4)2SiO4:Euphosphor prepared by solid-state reaction

Sr₅(PO₄)₂SiO₄:Eu²⁺ phosphosilicate phosphor was prepared by high temperature solid-state reaction. Effects of strontium sources (strontium oxide, strontium nitrate and strontium carbonate) and of phosphorus sources (diammonium phosphate, strontium monophosphate) on the reactivity of their mixture during heating and on phase composition, morphology and photoluminescence excitation and emission properties of the phosphors were investigated by TG–DTG–DSC, XRD, SEM and photoluminescence spectroscopy. The sequence of the solid-state reactions when using the different starting reagents was discussed based on the TG–DTG–DSC results. It was found that it is hard to prepare pure Sr₅(PO₄)₂SiO₄:Eu²⁺ phosphor with either of strontium sources studied when stoichiometric (NH₄)₂HPO₄ was used as a phosphorus source. Minor Sr₂SiO₄ impurity phase was present in the phosphors. The content of impurity phase, the morphology and resultant photoluminescence properties of the phosphors were markedly influenced by the strontium source employed. When SrCO₃ was used as the strontium source, the phase purity of the phosphor was improved with the addition of excess (NH₄)₂HPO₄. When (NH₄)₂HPO₄with 5% excess or SrHPO₄ in stoichiometric ratio was used as the phosphorus source a pure phase phosphor was obtained. In addition, the morphology and photoluminescence of the phosphor were also influenced by phosphorus source. The possible reasons causing different properties of the phosphors prepared using different raw materials were discussed based on reaction schemes.     

Improvement of coke resistance of Ni/Al2O3 catalyst in CH4/CO2 reforming by ZrO2 addition

This work investigates the improvement of Ni/Al₂O₃ catalyst stability by ZrO₂ addition for H₂ gas production from CH₄/CO₂ reforming reactions. The initial effect of Ni addition was followed by the effect of increasing operating temperature to 500–700 °C as well as the effect of ZrO₂ loading and the promoted catalyst preparation methods by using a feed gas mixture at a CH₄:CO₂ ratio of 1:1.25. The experimental results showed that a high reaction temperature of 700 °C was favored by an endothermic dry reforming reaction. In this reaction the deactivation of Ni/Al₂O₃ was mainly due to coke deposition. This deactivation was evidently inhibited by ZrO₂, as it enhances dissociation of CO₂ forming oxygen intermediates near the contact between ZrO₂ and nickel where the deposited coke is gasified afterwards. The texture of the catalyst or BET surface area was affected by the catalyst preparation method. The change of the catalyst texture resulted from the formation of ZrO₂–Al₂O₃ composite and the plugging of Al₂O₃ pore by ZrO₂. The 15% Ni/10% ZrO₂/Al₂O₃ co-impregnated catalyst showed a higher BET surface area and catalytic activity than the sequentially impregnated catalyst whereas coke inhibition capability of the promoted catalysts prepared by either method was comparable. Further study on long-term catalyst stability should be made.     

Electrochemical performance of Li3V2(PO4)3/C cathode material using a novel carbon source

Polyethylene glycol (PEG, mean molecular weight of 10,000) has been used to prepare a Li₃V₂(PO₄)₃/C cathode material by a simple solid-state reaction. The Raman spectra shows that the coating carbon has a good structure with a low I_D/I_G ratio. The images of SEM and TEM show that the carbon is dispersed between the Li₃V₂(PO₄)₃ particles, which improves the electrical contact between the corresponding particles. The electronic conductivity of Li₃V₂(PO₄)₃/C composite is 7.0 × 10⁻¹ S/cm, increased by seven orders of magnitude compared with the pristine Li₃V₂(PO₄)₃ (2.3 × 10⁻⁸ S/cm). At a low discharge rate of 0.28C, the sample presents a high discharge capacity of 131.2 mAh/g, almost achieving the theoretical capacity (132 mAh/g) for the reversible cycling of two lithium. After 500 cycles, the discharge capacity is 123.9 mAh/g with only 5.6% fading of the initial specific capacity. The Li₃V₂(PO₄)₃/C material also exhibits an excellent rate capability with high discharge capacities of 115.2 mAh/g at 1C and 106.4 mAh/g at 5C.     

Performance of Ni catalyst supported on La-hexaaluminate in CO<Subscript>2</Subscript> reforming of CH<Subscript>4</Subscript>

CO₂ reforming of CH₄ was performed using Ni catalyst supported on La-hexaaluminate which has been an well-known material for high-temperature combustion. La-hexaaluminate was synthesized by sol-gel method at various conditions where different amount of Ni (5–20 wt%) was loaded. Ni/La-hexaaluminate experienced 72 h reaction and its catalytic activity was compared with that of Ni/Al₂O₃, Ni/La-hexaaluminate shows higher reforming activity and resistance to coke deposition compared to the Ni/Al₂O₃ model catalyst. Coke deposition increases proportionally to Ni content. Consequently, Ni(5)/La-hexaaluminate(700) is the most efficient catalyst among various Ni/La-hexaaluminate catalysts regarding the cost of Ni in Ni(X)/La-hexaaluminate catalysts. BET surface area, XRD, EA, TGA and TPO were performed for surface characterization. This work was presented at the 6 ^th Korea-China Workshop on Clean Energy Technology held at Busan, Korea, July 4–7, 2006.     

Relaxor ferroelectric and photocatalytic properties of BaBi4Ti4O15

ABSTRACT

Aurivillius phase BaBi₄Ti₄O₁₅ micro-sized powders were produced by solid-state reaction and their photocatalytic properties were reported for the first time. X-ray diffraction revealed the polar orthorhombic structure. BaBi₄Ti₄O₁₅ ceramics exhibited diffuse phase transition at ～ 410°C. The freezing temperature of 274°C was obtained by fitting the Vogel–Fulcher law. The distinct ferroelectric domain switching current peaks in current – electric field (I-E) loop and piezoelectric coefficient d₃₃ value of 7.0?±?0.1 pC/N at room temperature further demonstrated relaxor ferroelectric behaviour of BaBi₄Ti₄O₁₅. UV-vis absorption spectra indicated that BaBi₄Ti₄O₁₅ had a direct band gap of 3.2?eV. The photocatalytic study showed 15% degradation of Rhodamine B (RhB) solution by BaBi₄Ti₄O₁₅ powders after 3.5?h UV-vis irradiation. The RhB degradation rate was further enhanced by depositing Ag nanoparticles on the BaBi₄Ti₄O₁₅ powders surface. This work suggested that the relaxor ferroelectric BaBi₄Ti₄O₁₅ is promising for photocatalytic applications.     

Degradation Effect and Mechanism of Dinitrotoluene Wastewater by Magnetic Nano-Fe3O4/H2O2 Fenton-like

The characteristics and influencing factors for dinitrotoluene degradation by nano-Fe₃O₄-H₂O₂ were studied, and the nano-scale Fe₃O₄ catalyst was prepared by the coprecipitation method, with dinitrotoluene wastewater as the degradation object. The results showed that the catalytic reaction system within the pH value range of 1 to 9 could effectively degrade dinitrotoluene, and the optimal pH value was 3; with the increase of catalyst dosage, the degradation efficiency and the catalytic reaction rate of dinitrotoluene grew as well. The optimal catalyst dosage was 1.0 g/L when the H₂O₂ dosage was within the range of 0 to 0.8 mL/L; the degradation efficiency and reaction rate grew with the increase of H₂O₂ dosage. With further increase of H₂O₂ dosage, degradation efficiency and reaction rate decreased; under the best conditions with the H₂O₂ dosage of 0.8 mL/L, the catalyst concentration of 1 g/L and the pH value of 3 at room temperature (25 °C), the degradation rate of the 100-mg/L dinitrotoluene in 120 min reached 97.6%. Through the use of the probe compounds n-butyl alcohol and benzoquinone, it was proved that the oxidation activity species in the nano-Fe₃O₄-H₂O₂ catalytic system were mainly hydroxyl radical (?OH) and superoxide radicals (HO2 ?), based on which, the reaction mechanism was hypothesized.     

Structure and electrochemical properties of nanocarbon-coated Li3V2(PO4)3 prepared by sol-gel method

A liquid-based sol-gel method was developed to synthesize nanocarbon-coated Li₃V₂(PO₄)₃. The products were characterized by XRD, SEM and electrochemical measurements. The results of Rietveld refinement analysis indicate that single-phase Li₃V₂(PO₄)₃ with monoclinic structure can be obtained in our experimental process. The discharge capacity of carbon-coated Li₃V₂(PO₄)₃ was 152.6 mAh/g at the 50th cycle under 1C rate, with 95.4% retention rate of initial capacity. A high discharge capacity of 184.1 mAh/g can be obtained under 0.12C rate, and a capacity of 140.0 mAh/g can still be held at 3C rate. The cyclic voltammetric measurements indicate that the electrode reaction reversibility is enhanced due to the carbon-coating. SEM images show that the reduced particle size and well-dispersed carbon-coating can be responsible for the good electrochemical performance obtained in our experiments.