A Phase-Locked Loop With Injection-Locked Frequency Multiplier in 0.18-$mu{hbox{m}}$ CMOS for $V$ -Band Applications

In this paper, a novel CMOS phase-locked loop (PLL) integrated with an injection-locked frequency multiplier (ILFM) that generates the $V$-band output signal is proposed. Since the proposed ILFM can generate the fifth-order harmonic frequency of the voltage-controlled oscillator (VCO) output, the operational frequency of the VCO can be reduced to only one-fifth of the desired frequency. With the loop gain smaller than unity in the ILFM, the output frequency range of the proposed PLL is from 53.04 to 58.0 GHz. The PLL is designed and fabricated in 0.18-$mu{hbox{m}}$ CMOS technology. The measured phase noises at 1- and 10-MHz offset from the carrier are $-$ 85.2 and $-{hbox{90.9 dBc}}/{hbox{Hz}}$, respectively. The reference spur level of $-{hbox{40.16 dBc}}$ is measured. The dc power dissipation of the fabricated PLL is 35.7 mW under a 1.8-V supply. It can be seen that the advantages of lower power dissipation and similar phase noise can be achieved in the proposed PLL structure. It is suitable for low-power and high-performance $V$-band applications.      

17 GHz RF Front-Ends for Low-Power Wireless Sensor Networks

A 17 GHz low-power radio transceiver front-end implemented in a 0.25 $mu{hbox {m}}$ SiGe:C BiCMOS technology is described. Operating at data rates up to 10 Mbit/s with a reduced transceiver turn-on time of 2 $mu{hbox {s}}$, gives an overall energy consumption of 1.75 nJ/bit for the receiver and 1.6 nJ/bit for the transmitter. The measured conversion gain of the receiver chain is 25–30 dB into a 50 $Omega$ load at 10 MHz IF, and noise figure is 12 $pm$0.5 dB across the band from 10 to 200 MHz. The 1-dB compression point at the receiver input is $-$37 dBm and ${hbox{IIP}}_{3}$ is $-$25 dBm. The maximum saturated output power from the on-chip transmit amplifier is $-$1.4 dBm. Power consumption is 17.5 mW in receiver mode, and 16 mW in transmit mode, both operating from a 2.5 V supply. In standby, the transceiver supply current is less than 1 $mu{hbox {A}}$.      

A 22–29-GHz UWB Pulse-Radar Receiver Front-End in 0.18-$mu{hbox{m}}$ CMOS

The design of a CMOS 22–29-GHz pulse-radar receiver (RX) front-end for ultra-wideband automotive radar sensors is presented. The chip includes a low-noise amplifier, in-phase/quadrature mixers, a quadrature voltage-controlled oscillator (QVCO), pulse formers, and baseband variable-gain amplifiers. Fabricated in a 0.18-$mu{hbox{m}}$ CMOS process, the RX front-end chip occupies a die area of 3 ${hbox{mm}}^{2}$. On-wafer measurements show a conversion gain of 35–38.1 dB, a noise figure of 5.5–7.4 dB, and an input return loss less than $-$14.5 dB in the 22–29-GHz automotive radar band. The phase noise of the constituent QVCO is $-$107 dBc/Hz at 1-MHz offset from a center frequency of 26.5 GHz. The total dc power dissipation of the RX including output buffers is 131 mW.      

An Edge Missing Compensator for Fast Settling Wide Locking Range Phase-Locked Loops

An edge missing compensator (EMC) is proposed to approach the function of an ideal PD with $pm 2 ^{N-1} times 2pi $ linear range with $N$-bit EMC. A PLL implemented with a 9-bit EMC achieves 320 MHz frequency hopping within 10 $~mu{hbox {s}}$ logarithmically which is about 2.4 times faster than the conventional design. The reference spur of the PLL is ${-}{hbox {48.7~dBc}}$ and the phase noise is ${-}hbox{88.31~dBc/Hz}$ at 10 kHz offset with $K_{rm VCO}= -$ 2 GHz/V.      

A CMOS Backgate-Coupled QVCO Based on Back-to-Back Series Varactor Configuration for Minimal AM-to-PM Noise Conversion

A 3.3 GHz CMOS quadrature voltage-controlled oscillator (QVCO) with very low phase noise is presented. The back-to-back series varactor configuration is employed in the LC tank for minimizing the AM-to-PM noise conversion. The backgate coupling for quadrature phase inter-locking further eliminates the noise contribution from coupling transistors and also reduces power consumption. The implemented QVCO in 0.18 $mu{rm m}$ CMOS technology achieved very low phase noise of ${- 133}~{rm dBc}/{rm Hz}$ at 1 MHz offset, where the total power consumption is 4.4 mW from a 1.0 V supply. The chip has a very high FOM of ${- 196.6}~{rm dBc}/{rm Hz}$.      

A 0.22 V Quadrature VCO in 90 nm CMOS Process

This letter presents an ultra-low voltage quadrature voltage-controlled oscillator (QVCO). The LC-tank QVCO consists of two low-voltage voltage-controlled oscillators (VCOs) with the body dc biased at the drain bias through a resistor. The superharmonic and back-gate coupling techniques are used to couple two differential VCOs to run in quadrature. The proposed CMOS QVCO has been implemented with the UMC 90 nm CMOS technology and the die area is 0.827 $, times ,$0.913 mm $^{2}$. At the supply voltage of 0.22 V, the total power consumption is 0.33 mW. The free-running frequency of the QVCO is tunable from 3.42 to 3.60 GHz as the tuning voltage is varied from 0.0 to 0.3 V. The measured phase noise at 1 MHz offset is ${-}112.97$ dBc/Hz at the oscillation frequency of 3.55 GHz and the figure of merit (FOM) of the proposed QVCO is about ${-}188.79$ dBc/Hz.      

A 108 dB SNR, 1.1 mW Oversampling Audio DAC With A Three-level DEM Technique

A low power audio oversampling $Sigma Delta $ digital-to-analog converter (DAC) with a three-level $(+1,~0,-1)$ dynamic-element-matching (DEM) technique and an inter-symbol interference-free (ISI) output stage is presented. Solutions for design challenges such as ISI, clock jitter sensitivity, and out-of-band noise are presented. The converter is fabricated in a 0.18 $mu{hbox {m}}$ CMOS process, occupies 0.55 ${hbox {mm}}^{2}$, achieves 108 dB dynamic range, $-98~{rm dB ~THD}+{rm N}$ while consumes a total of 1.1 mW per channel at 1.8 V supply.      

A 5-GHz CMOS Type-II PLL With Low $K_{rm VCO}$ and Extended Fine-Tuning Range

A 5-GHz dual-path integer-$N$ Type-II phase-locked loop (PLL) uses an LC voltage-controlled oscillator and softly switched varactors in an overlapped digitally controlled integral path to allow a large fine-tuning range of approximately 160 MHz while realizing a low susceptibility to noise and spurs by using a low $K_{rm VCO}$ of 3.2 MHz/V. The reference spur level is less than $-$70 dBc with a 1-MHz reference frequency and a total loop-filter capacitance of 26 pF. The measured phase noise is $-$75 and $-$115 dBc/Hz at 10-kHz and 1-MHz offsets, respectively, using a loop bandwidth of approximately 30 kHz. This 0.25-${hbox{mm}}^{2}$ PLL is fabricated in a 90-nm digital CMOS process and consumes 11 mW from a 1.2-V supply.      

A Low-Voltage Mobility-Based Frequency Reference for Crystal-Less ULP Radios

The design of a 100 kHz frequency reference based on the electron mobility in a MOS transistor is presented. The proposed low-voltage low-power circuit requires no off-chip components, making it suitable for application in wireless sensor networks (WSN). After a single-point calibration, the spread of its output frequency is less than 1.1% (3$sigma $) over the temperature range from $-{hbox{22}},^{circ}{hbox{C}}$ to 85$,^{circ}{hbox{C}}$ . Fabricated in a baseline 65$~$nm CMOS technology, the frequency reference circuit occupies 0.11$ hbox{mm}^{2}$ and draws 34 $ muhbox{A}$ from a 1.2 V supply at room temperature.      

A Sub-100 $mu{rm W}$ Ku-Band RTD VCO for Extremely Low Power Applications

This letter presents the microwave performance of a sub-100 $mu{rm W}$ Ku-band differential-mode resonant tunneling diode (RTD)-based voltage controlled oscillator (VCO) with an extremely low power consumption of 87 $mu{rm W}$ using an InP-based RTD/HBT MMIC technology. In order to achieve the extremely low-power Ku-band RTD VCO, the device size of RTD is scaled down to $0.6times 0.6 mu{rm m}^{2}$. The obtained dc power consumption of 87 $mu{rm W}$ is found to be only 1/18 of the conventional-type MMIC VCOs reported in the Ku-band. The fabricated RTD VCO has a phase noise of $-$100.3 dBc/Hz at 1 MHz offset frequency and a tuning range of 140 MHz with the figure-of-merit (FOM) of $-$194.3 dBc/Hz.      

A Dual-Band Self-Oscillating Mixer for -Band and -Band Applications

A self-oscillating mixer that employs both the fundamental and harmonic signals generated by the oscillator subcircuit in the mixing process is experimentally demonstrated. The resulting circuit is a dual-band down-converting mixer that can operate in $C$ -band from 5.0 to 6.0 GHz, or in $X$-band from 9.8 to 11.8 GHz. The oscillator uses active superharmonic coupling to enforce the quadrature relationship of the fundamental outputs. Either the fundamental outputs of the oscillator or the second harmonic oscillator output signals that exists at the common-mode nodes are connected to the mixer via a set of complementary switches. The mixer achieves a conversion gain between 5–12 dB in both frequency bands. The output 1-dB compression points for both modes of the mixer are approximately $-{hbox{5 dBm}}$ and the output third-order intercept point for $C$ -band and $X$ -band operation are 12 and 13 dBm, respectively. The integrated circuit was fabricated in 0.13-$mu {hbox{m}}$ CMOS technology and measures ${hbox{0.525 mm}}^{2}$ including bonding pads.      

Low-Threshold Strained Quantum-Well GaSb-Based Lasers Emitting in the 2.5- to 2.7-$mu$ m Wavelength Range

GaInAsSb–GaSb strained quantum-well (QW) ridge waveguide diode lasers emitting in the wavelength range from 2.51 to 2.72 $ mu{hbox {m}}$ have been grown by molecular beam epitaxy. The devices show ultralow threshold current densities of 44 $hbox{A}/{hbox {cm}}^{2}$ (${L}rightarrow infty $) for a single QW device at 2.51 $ mu{hbox {m}}$, which is the lowest reported value in continuous-wave operation near room temperature (15 $^{circ}hbox{C}$) at this wavelength. The devices have an internal loss of 3 ${hbox {cm}}^{-1}$ and a characteristic temperature of 42 K. By using broader QWs, wavelengths up to 2.72 $mu{hbox {m}}$ could be achieved.      

A Single-Ended Fully Integrated SiGe 77/79 GHz Receiver for Automotive Radar

A single-ended 77/79 GHz monolithic microwave integrated circuit (MMIC) receiver has been developed in SiGe HBT technology for frequency-modulated continuous-wave (FMCW) automotive radars. The single-ended receiver chip consists of the first reported SiGe 77/79 GHz single-ended cascode low noise amplifier (LNA), the improved single-ended RF double-balanced down-conversion 77/79 GHz micromixer, and the modified differential Colpitts 77/79 GHz voltage controlled oscillator (VCO). The LNA presents 20/21.7 dB gain and mixer has 13.4/7 dB gain at 77/79 GHz, and the VCO oscillates from 79 to 82 GHz before it is tuned by cutting the transmission line ladder, and it centres around 77 GHz with a tuning range of 3.8 GHz for the whole ambient temperature variation range from $- hbox{40},^{circ}{hbox{C}}$ to $+ hbox{125},^{circ}{hbox{C}}$ after we cut the lines by tungsten-carbide needles. Phase noise is $-$90 dBc/Hz@1 MHz offset. Differential output power delivered by the VCO is 5 dBm, which is an optimum level to drive the mixer. The receiver occupies 0.5 ${hbox{mm}}^{2}$ without pads and 1.26 ${hbox{mm}}^{2}$ with pads, and consumes 595 mW. The measurement of the whole receiver at 79 GHz shows 20–26 dB gain in the linear region with stable IF output signal. The input ${rm P}_{rm 1dB}$ of the receiver is $-$35 dBm.      

A 5-GHz CMOS Frequency Synthesizer With an Injection-Locked Frequency Divider and Differential Switched Capacitors

A phase-locked loop (PLL)-based frequency synthesizer at 5 GHz is designed and fabricated in 0.18-${rm mu}hbox{m}$ CMOS technology. The power consumption of the synthesizer is significantly reduced by using an injection-locked frequency divider (ILFD) as the first frequency divider in the PLL feedback loop. The synthesizer chip consumes 18 mW of power, of which only 3.93 mW is consumed by the voltage-controlled oscillator (VCO) and the ILFD at 1.8-V supply voltage. The VCO has the phase noise of $-$ 104 dBc/Hz at 1-MHz offset and an output tuning range of 740 MHz. The chip size is 1.1 mm $times$ 0.95 mm.      

Low Phase Noise G$ _{m}$-Boosted Differential Gate-to-Source Feedback Colpitts CMOS VCO

This paper presents a ${g} _{ m}$-boosted differential gate-to-source feedback Colpitts (GS-Colpitts) CMOS voltage-controlled oscillator (VCO) that consumes a lower oscillation start-up current. The proposed architecture allows a wider range of saturation mode operation for the switching transistors, which helps suppress AM-to-FM conversion by these transistors. In addition, the phase noise contribution of the flicker noise in the switching transistor is reduced through the capacitor feedback network of the Colpitts oscillator. As a result, the proposed topology can achieve better phase noise performance and a higher figure of merit (FOM) compared to a conventional NMOS-only cross-coupled VCO. The proposed VCO is implemented in a 0.18-$mu{hbox {m}}$ CMOS for 1.78 to 1.93 GHz operation. At 1.86 GHz, the measurements show phase noise of $-$105 and $-hbox{128~dBc/Hz}$ (corresponding to ${rm FOM}= 191.2$) at offsets of 100 kHz and 1 MHz, respectively, while dissipating 1.8 mA from a 0.9-V supply.      

$hbox{TiN/ZrO}_{2}$/Ti/Al Metal–Insulator–Metal Capacitors With Subnanometer CET Using ALD-Deposited $hbox{ZrO}_{2}$ for DRAM Applications

We provide the first report of the structural and electrical properties of $hbox{TiN/ZrO}_{2}$/Ti/Al metal–insulator–metal capacitor structures, where the $hbox{ZrO}_{2}$ thin film (7–8 nm) is deposited by ALD using the new zirconium precursor ZrD-04, also known as Bis(methylcyclopentadienyl) methoxymethyl. Measured capacitance–voltage ($C$– $V$) and current–voltage ( $I$–$V$) characteristics are reported for premetallization rapid thermal annealing (RTP) in $hbox{N}_{2}$ for 60 s at 400 $^{circ}hbox{C}$, 500 $^{circ}hbox{C}$, or 600 $^{ circ}hbox{C}$. For the RTP at 400 $^{circ}hbox{C}$ , we find very low leakage current densities on the order of nanoamperes per square centimeter at a gate voltage of 1 V and low capacitance equivalent thickness values of $sim$ 0.9 nm at a gate voltage of 0 V. The dielectric constant of $ hbox{ZrO}_{2}$ is 31 $pm$ 2 after RTP treatment at 400 $^{circ}hbox{C}$.      

Design and Analysis of a 90 nm mm-Wave Oscillator Using Inductive-Division LC Tank

A 60 GHz voltage-controlled oscillator with an inductive division LC tank has been designed in 90 nm CMOS. The analysis of the oscillator shows that the presence of higher harmonics, the capacitance nonlinearity and the very high $K _{rm VCO}$ are critical for the phase noise performance of oscillators. Therefore, a pseudo-differential amplifier is employed in this design because of its high linearity. Furthermore, the proposed inductive division reduces the phase noise by increasing the signal amplitude across the varactor, without affecting the operation mode of the cross-coupled pair transistors. It also helps to increase the tuning range by isolating the varactor from the parasitic capacitances of the transistors and interconnects. The mm-wave oscillator is fabricated in a 90 nm CMOS technology. Under 0.7 V supply, the oscillator achieves a tuning range from 53.2 GHz to 58.4 GHz, consuming 8.1 mW. At 58.4 GHz, the phase noise is $-hbox{91~dBc}/hbox{Hz}$ at 1 MHz offset. Under 0.43 V supply, the oscillator achieves a tuning range from 58.8 to 61.7 GHz. At 61.7 GHz, the phase noise is $-hbox{90~dBc}/hbox{Hz}$ @1$~$MHz offset with a power consumption of only 1.2 mW.      

A Short Range, Low Data Rate, 7.2 GHz-7.7 GHz FM-UWB Receiver Front-End

A 9 mW FM-UWB receiver front-end for low data rate ( $≪$$ hbox{50~kbps}$), short range ( $≪$$hbox{10~m}$) applications operating in the ultra-wideband (UWB) band centered at 7.45 GHz is described in this paper. A single-ended-to-differential preamplifier with 30 dB voltage gain, a 1 GHz bandwidth FM demodulator, and a combined (preamp/demodulator) receiver front-end were fabricated in 0.25 $muhbox{m}$ SiGe:C BiCMOS and characterized. Measured receiver sensitivity is $-hbox{85.8~dBm}$ while consuming 9 mW from a 1.8 V supply, and $-hbox{83~dBm}$ consuming 6 mW at 1.5 V. 15-20 m range line-of-sight in an indoor environment is realized, justifying FM-UWB as a robust radio technology for short range, low data rate applications. Multi-user and interference capabilities are also evaluated.      

An Analytical Method to Extract the Physical Parameters of a Solar Cell From Four Points on the Illuminated $J{-}V$ Curve

For a variety of solar cells, it is shown that the single exponential $J{-}V$ model parameters, namely—ideality factor $eta$ , parasitic series resistance $R_{s}$, parasitic shunt resistance $R_{rm sh}$, dark current $J_{0}$, and photogenerated current $J_{rm ph}$ can be extracted simultaneously from just four simple measurements of the bias points corresponding to $V_{rm oc}$, $sim!hbox{0.6}V_{rm oc}$, $J_{rm sc}$, and $sim! hbox{0.6}J_{rm sc}$ on the illuminated $J{-}V$ curve, using closed-form expressions. The extraction method avoids the measurements of the peak power point and any $dJ/dV$ (i.e., slope). The method is based on the power law $J{-}V$ model proposed recently by us.      

$S$ - and $C$ -Band Ultra-Compact Phase Shifters Based on All-Pass Networks

Ultra-compact phase shifters are presented. The proposed phase-shifting circuits utilize the lumped element all-pass networks. The transition frequency of the all-pass network, which determines the size of the circuit, is set to be much higher than the operating frequency. This results in a significantly small chip size of the phase shifter. To verify this methodology, 5-bit phase shifters have been fabricated in the $S$ - and $C$ -band. The $S$ -band phase shifter, with a chip size of 1.87 mm $,times,$0.87 mm (1.63 mm $^{2}$), has achieved an insertion loss of ${hbox{6.1 dB}} pm {hbox{0.6 dB}}$ and rms phase-shift error of less than 2.8$^{circ}$ in 10% bandwidth. The $C$ -band phase shifter, with a chip size of 1.72 mm $,times,$0.81 mm (1.37 mm $^{2}$), has demonstrated an insertion loss of 5.7 dB $pm$ 0.8 dB and rms phase-shift error of less than 2.3 $^{circ}$ in 10% bandwidth.