Friction and Wear Behavior of WS2/Zr Self-lubricating Soft Coatings in Dry Sliding Against 40Cr-Hardened Steel Balls

WS₂ and WS₂/Zr self-lubricating soft coatings were produced by medium-frequency magnetron sputtering, multi-arc ion plating and ion-beam-assisted deposition technique on the cemented carbide YT15 (WC + 15 % TiC + 6 % Co) substrates. Microstructural and fundamental properties of these coatings were examined. Sliding wear tests against 40Cr-hardened steel using a ball-on-disk tribometer method were carried out with these coated materials. The friction coefficient and wear rates were measured with various applied loads and sliding speeds. The wear surface features of the coatings were examined using SEM. The results showed that the WS-1 specimen (with WS₂/Zr composite coating) has higher hardness and coating/substrate critical load compared with that of the WS-2 specimen (only with WS₂ coating). The friction coefficient of WS-1 specimen increases with the increase in applied load and is quite insensitive to the sliding speed. The wear rate of the WS-1 specimen is almost constant under different applied loads and sliding speeds. The WS-1 specimen shows the smallest friction coefficient and wear rate among all the specimens tested under the same conditions. The WS-1 specimen exhibits improved friction behavior to that of the WS-2 specimen, and the antiwear lifetime of the WS₂ coatings can be prolonged through adding Zr additives. The self-lubricating and wear mechanism of the WS₂/Zr coating was also found from the sliding wear tests.     

Tribological properties of Ni3Al-Cr7C3 composite coating under water lubrication

The tribological properties of Ni₃Al-Cr₇C₃ composite coating under water lubrication were examined by using a ball-on-disc reciprocating tribotester. The effects of load and sliding speed on wear rate of the coating were investigated. The worn surface of the coating was analyzed using electron probe microscopy analysis (EPMA) and X-ray photoelectron spectroscopy (XPS). The results show the friction coefficient of the coating is decreased under water lubrication. The wear rate of the coating linearly increases with the load. At high sliding speed, the wear rate of the coating is dramatically increased and a large amount of the counterpart material is transferred to the coating worn surface. The low friction of the coating under water lubrication is due to the oxidizing of the worn surface in the wear. The wear mechanism of the coating is plastic deformation at low normal load and sliding speed. However, the wear mechanism transforms to microfracture and microploughing at high load with low sliding speed, and oxidation wear at high sliding speed. It is concluded that the contribution of the sliding speed to an increase in the coating wear is larger than that of the normal load.     

铜锡铅锌合金的摩擦磨损性能

利用MMU-200型摩擦磨损试验机研究了铜锡铅锌合金与GCr15钢对磨时的摩擦磨损特性,利用扫描电子显微镜对合金的磨损表面形貌进行了观察。结果表明:铜锡铅锌合金的磨损率随载荷和摩擦速度的增加而增大;其摩擦因数随摩擦速度的增加而减小,随载荷的增加先增大后减小;其磨损机制主要为磨粒磨损和粘着磨损;合金中的铅相起到了润滑作用,有利于提高合金的耐磨性能。     

38CrSi自配副的摩擦磨损性能

采用自制的销盘式摩擦磨损试验机研究了38CrSi自配副干滑动时的摩擦因数、磨损率随滑动速度和载荷的变化规律;利用SEM观察了磨损面的微观形貌,分析了摩擦磨损机理。结果表明:其摩擦因数随着载荷和速度的增加而减小;磨损率随着载荷的增加而增大,随着速度的增加先增大后减小,和常用材料的磨损率随速度增加而增大的规律不同;磨损机理为磨粒磨损和粘着磨损。     

Friction and wear behavior of flame-sprayed PEEK coatings

Polyetheretherketone (PEEK) becomes of great interest to applications as bearing and slider materials. In this paper, PEEK coatings with three kinds of crystallinities were deposited using the flame spray process. Employing a uniform design experiment, the friction and wear behavior of the three PEEK coatings were systematically investigated under dry sliding conditions against a 100C6 counterbody on a ball-on-disc arrangement for several loads and sliding velocities. For the three coatings, the friction coefficient significantly followed the normal distribution. The average friction coefficients appeared to decrease while increasing the sliding velocity, but were insensitive to the applied load in the range of investigation. Among the three coatings, the higher the crystallinity of the coating, the lower its average friction coefficient was. The wear rate of the coating with the lowest crystallinity decreased with an increase in the load and a decrease in the sliding velocity. The wear rate of the coating with the intermediate crystallinity decreased with an increase in the load, but increased with an increase in the sliding velocity at lower loads, and then decreased with an increase in the velocity at higher loads. The wear rate of the coating with the highest crystallinity decreased with the increase of both the load and the sliding velocity. The wear mechanisms of the different coatings are explained in terms of plastic deformation, plogh marks and fatigue tearing.     

热压Ni-MoS2自润滑复合材料在不同温度的往复摩擦磨损特性

采用自润滑复合材料,对提高某些机械摩擦副的使用寿命有很显著的效果。研究了热压Ni-MoS2自润滑复合材料与GCr15钢球组成的点接触配对副,在室温和高温条件下进行微幅往复摩擦运动时的自润滑特性。考察了载荷、温度及MoS2含量对摩擦系数和磨损率的影响,并借助扫描电镜观察磨损表面的形貌特征。结果表明：摩擦系数随载荷增加而不断提高;温度在400℃以下时,摩擦系数能保持较低数值;在室温和250℃时,含60%MoS2的复合材料均具有最低磨损率;提高MoS2含量有助于改善高温自润滑性;MoS2转移润滑膜的完整程度可作为Ni-MoS2复合材料自润滑性能好坏的判据。     

Tribological properties of flame sprayed Fe–Ni–RE alloy coatings under reciprocating sliding

Fe–Ni–RE self-fluxing alloy powders were flame sprayed onto 1045 carbon steel. The tribological properties of Fe–Ni–RE alloy coatings under dry sliding against SAE52100 steel at ambient conditions were studied on an Optimol SRV oscillating friction and wear tester in a ball-on-disc contact configuration. Effects of load and sliding speed on tribological properties of the Fe–Ni–RE coatings were investigated. The worn surfaces of the Fe–Ni–RE alloy coatings were examined with a scanning electron microscopy(SEM) and an energy-dispersive spectroscopy(EDS). It was found that the Fe–Ni–RE alloy coatings had better wear resistance than the SAE52100 steel. An adhered oxide debris layer was formed on the worn surface in friction. Area of the friction layer varied with variety of sliding speed, but did not vary with load. The oxide layer contributed to decreased wear, but increased friction. Wear rate of the material increased with the load, but dramatically decreased at first and then slightly decreased the sliding speed. The friction coefficient of the material was 0.40-0.58, and decreased slightly with the load, but increased with sliding speed at first, and then tended to be a constant value. Wear mechanism of the coatings was oxidation wear and a large amount of counterpart material was transferred to the coatings.     

Friction and Wear Behavior of Steels under Different Reciprocating Sliding Conditions

The friction and wear behavior of ISO 100Cr6 steel ball sliding against conventionally hardened carbon and low-alloy steels was studied. The effect of hardness, hardening capacity, normal load, and sliding speed on the coefficient of friction and friction energy was investigated. Friction tests were carried out, without lubrication and under ambient conditions, on a reciprocating friction tester in which a ball-on-flat contact configuration was adopted. The results showed that there is a relative tendency for the friction properties to decrease with increased hardening capacity and decreased hardness. The results showed that increasing normal load decreases the coefficient of friction for the two steel nuances. However, increasing sliding speed increases the coefficient of friction of low-alloy steel and decreases the coefficient of friction of carbon steel. The oxidation of wear debris influences the wear mechanisms and friction behavior.     

采煤机滑靴激光熔覆铁镍基涂层的抗磨性能*

为提高采煤机滑靴在无油工况下的耐磨性,采用激光熔覆技术在45钢为基体上分别制备FeNiMo和FeNiMoSi涂层,并对其物相组成及硬度等进行分析。结果发现：制备的涂层结构致密,与基底保持了良好的冶金结合;FeNiMoSi涂层的平均硬度为438HV,分别约为基体（153HV）的2.8倍以及FeNiMo涂层（385HV）的1.1倍。通过往复式摩擦磨损试验机研究涂层的干摩擦磨损性能,并探讨其磨损机制。结果表明：随着载荷和滑动速度的增大,涂层的摩擦因数均呈现出减小的趋势;随着载荷的增大,涂层的磨损率逐渐升高;随着滑动速度的增大,FeNiMo涂层的磨损率出现先下降后上升的趋势,而FeNiMoSi涂层的磨损率则逐渐下降;涂层的磨损机制主要为磨粒磨损、塑性变形以及轻微的氧化磨损。总体来说,FeNiMoSi涂层相比FeNiMo涂层表现出更好的耐磨性能,这是因为涂层中Si元素的添加,不仅起到细晶强化作用,而且促进了FeSi金属间化合物相的生成。     

铜碲硒铁合金的干摩擦磨损性能

利用环-盘式摩擦磨损试验机研究了铜碲硒铁合金的干摩擦磨损行为,分析了载荷和摩擦速度等参数对该合金摩擦磨损性能的影响,并用扫描电子显微镜对磨损形貌进行了观察.结果表明:铜碲硒铁合金的摩擦因数随载荷的增加变化不大,但随摩擦速度的增加而明显增大;合金的磨损率随载荷和摩擦速度的增加均增大;在轻载低速条件下,合金的磨损机制以犁削磨损和粘着磨损为主;在重载高速条件下,磨粒磨损和粘着磨损加剧.     

Tribological Behavior of Tin-Based Babbitt Alloy Lubricated by Seawater

In this article, the tribological behaviors of tin-based Babbitt alloy ZChSnSb 8–8 sliding against AISI 302 stainless steel lubricated by seawater were investigated. The results indicated that the friction coefficient decreases with increasing load and sliding speed, and the wear rate increases slightly with load but decreases with sliding speed. The low friction coefficient and wear rate are attributed to the unique “concrete structure” and seawater. As a lubrication medium, seawater has lubricating, cooling, and corrosive effects on the sliding couple.     

载流条件下的1Cr18Ni9Ti/浸金属碳摩擦磨损性能研究

在销-盘摩擦磨损试验机上试验了载荷、速度、电流对1Cr18Ni9Ti/浸金属碳对磨时的摩擦因数、磨损量及磨损形貌的影响。试验结果表明,载荷对1Cr18Ni9Ti/浸金属碳摩擦副的摩擦因数和销试样的磨损率有显著影响:载荷越大,摩擦因数越大,磨损率越低;摩擦因数、磨损率与速度的关系受载荷的制约。当低载时,以电流影响为主。销试样的磨损表面出现了粘着磨损,氧化磨损和电弧烧蚀。     

Sliding wear behavior of planar random zinc-alloy matrix composites

The friction and wear behavior of planar random zinc-alloy matrix composites reinforced by discontinuous carbon fibres under dry sliding and lubricated sliding conditions has been investigated using a block-on-ring apparatus. The effects of fibre volume fractions and loads on the sliding wear resistance of the zinc-alloy matrix composites were studied. Experiments were performed within a load range of 50–300 N at a constant sliding velocity of 0.8 m s⁻¹. The composites with different volume fractions of carbon fibres (0–30%) were used as the block specimens, and a medium-carbon steel used as the ring specimen. Increasing the carbon fibre volume fraction significantly decreased the coefficient of friction and wear rates of both the composites and the medium-carbon steel under dry sliding conditions. Under lubricated sliding conditions, however, increasing the carbon fibre volume fraction substantially increased the coefficient of friction, and slightly increased the wear of the medium-carbon steel, while reducing the wear of the composite.Under dry sliding conditions, an increasing load increased not only the wear rates of both the composite and the unreinforced zinc alloy, but also those of their corresponding steel rings. However, the rate of increase of wear with increasing load for both the composite and its corresponding steel ring was much smaller than for the unreinforced zinc alloy and its corresponding steel ring. The coefficient of friction under dry sliding conditions appeared to be constant as load increased within a load range of 50–150 N for both the composite and the unreinforced zinc alloy, but increased at the higher loads. Under any load the coefficient of friction of the composite was lower than half that of the unreinforced zinc alloy under dry sliding conditions.     

Tribocorrosion behavior of Ni-17.5Si-29.3Cr alloy in sulfuric acid solution

The tribocorrosion property of a Ni-17.5Si-29.3Cr alloy against a Si₃N₄ ball was studied in comparison with AISI321 stainless steel using a ball-on-disk reciprocating tribotester in 1 M sulfuric acid (H₂SO₄) solution. The effects of load and sliding speed on the tribocorrosion properties of the alloy were investigated. The results indicated that the wear rate of the alloy increased while the friction coefficient decreased with increasing load. The wear rate of the alloy increased linearly with increasing sliding speed and the friction coefficient increased in the initial stages and then remained constant with increasing sliding speed. The wear mechanisms were mainly microploughing, uniform corrosion and pitting corrosion. Under the experimental conditions of the present study, the Ni-17.5Si-29.3Cr alloy showed excellent corrosion-resistence and anti-wear ability compared with AISI321 stainless steel.     

On dry sliding friction and wear behaviour of PEEK and PEEK/SiC-composite coatings

In this work, polyetheretherketone (PEEK) and PEEK/SiC-composite coatings were deposited on Al substrates using a printing technique to improve their surfaces performance. The objective of this work was to investigate coatings friction and wear behaviour. Especially, the effect of sliding velocity and applied load on coatings friction coefficient and wear rate was evaluated in range of 0.2-1.4 m/s and 1-9 N, respectively. Compared to Al substrate, the coated samples exhibit excellent friction coefficient and wear rate. For PEEK coating, under an applied load of 1 N, the increase in sliding velocity can result in decreasing of friction coefficient at a cost of wear resistance. Under a load of 9 N, however, PEEK coating exhibits the highest friction coefficient and wear rate at an intermediate velocity. These influences appear to be mainly ascribed to the influence of contact temperature of the two relative sliding parts. In most test conditions, the composite coating exhibits better wear resistance and a little higher friction coefficient. SiC reinforcement in composite coating plays a combined role. First of all, it might lead to energy dissipation for activation of fracture occurred on the interface of PEEK and the powders. Moreover, it can reduce coating ploughs and the adhesion between the two relative sliding parts.     

M35与GCr15干摩擦磨损性能的研究

在HT-1000型高温摩擦磨损试验机上,对M35高速钢进行干滑动摩擦磨损试验,利用SEM(扫描电镜)观察并分析摩擦面磨损形貌及磨损机理。结果表明,M35高速钢在与GCr15滚动轴承合金钢配副干摩擦条件下,随着速度的增加,摩擦因数先降低后升高,然后再降低。当摩擦热累积达到一定值后,摩擦表面产生严重塑性变形和化学变化,摩擦副表面产生氧化磨损、粘着磨损、磨粒磨损和犁沟磨损,形成转移润滑膜,此时摩擦因数较低,磨损率也相对较低。     

Investigation of the Transition State in the Wear of Polyphenylene Sulfide Sliding Against Steel

The effect of sliding variables, including counterface roughness, sliding speed, and contact pressure, on the run-in state of wear and friction was studied. Sliding was performed in the pin-on-disk configuration with a polyphenylene sulfide (PPS) pin resting on the flat steel counterface. Some experiments were also run to study the effect of air cooling and heating. Optical microscopy and scanning electron microscopy were used to study the shape and size of the wear debris, worn pin surface, and the transfer film formed on steel counterfaces. It was found that friction and wear in the run-in state were significantly affected by the sliding variables studied and their influence was closely related to the development of a transfer film during the run-in state. If the transfer film developed during initial sliding, the coefficient of friction increased and wear rate decreased. The wear rate in the run-in state increased with the increase in initial counterface roughness and there was an optimal counterface roughness of 0.06 m Ra for minimum steady state wear rate. A higher applied load led to a higher wear rate in the run-in state but that was not the case with steady state wear rate.     

Wear and friction behavior of sand cast brake rotor made of A359-20 vol% SiC particle composites sliding against automobile friction material

The effect of load range of 30-100 N and speed range of 3-12 m/s on the wear and friction behavior of sand cast brake rotor made of A359-20 vol% SiC particle composites sliding against automobile friction material was investigated. Dry sliding frictional and wear behavior were investigated in a pin-on-disc type apparatus. Automobile friction material was used as pin, while the A359-20 vol% SiC particle composites formed the rotating disc. For comparison, the wear and friction behavior of commercially used cast iron brake rotor were studied. The results showed that the wear rate of the composite disc decreased with increasing the applied load from 30 to 50 N and increased with increasing the load from 50 to100 N. However, the wear rate of the composite disc decreased with increasing the sliding speed at all levels of load applied in the present work. For all sliding speeds, the friction coefficient of the composite disc decreased with applied load. The worn surfaces as well as wear debris were studied using scanning electron microscopy (SEM), energy dispersive X-ray (EDX) analyzer and X-ray diffraction (XRD) technique. At load of 50 N and speed range of 3-12 m/s, the worn surface of the composite disc showed a dark adherent layer, which mostly consisted of constituents of the friction material. This layer acted as a protective coating and lubricant, resulting in an improvement in the wear resistance of the composite.     

腐蚀介质条件下NiCrBSi/WC喷熔层的摩擦学性能研究

采用氧-乙炔火焰喷熔工艺,制备了碳化钨颗粒增强镍基合金喷熔层(NiCrBSi/WC),研究了它在腐蚀介质条件下的摩擦磨损行为与机理,并考察了载荷、滑动速度对其摩擦磨损性能的影响规律。研究结果表明:NiCrBSi/WC具有良好的耐腐蚀磨损性能,且当WC含量为20%时,腐蚀磨损率最低;WC含量超过20%后,由于喷熔层存在“腐蚀原电池”效应,其腐蚀磨损率增大。NiCrBSi/WC的腐蚀磨损率随载荷增加而变大,随速度增大而减小。载荷的增加使喷熔层的犁削磨损加剧,导致摩擦系数和磨损率增大;速度的增大造成摩擦界面温度上升,可生成摩擦转移膜,从而降低了喷熔层的磨损率。     

Monitoring of Wear Characteristics of TiN and TiAlN Coatings at Long Sliding Distances

TiN and TiAlN thin hard coatings have been widely applied on machine components and cutting tools to increase their wear resistance. These coatings have different wear behaviors, and determination of their wear characteristics in high-temperature and high-speed applications has great importance in the selection of suitable coating material to application. In this article, the wear behavior of single-layer TiN and TiAlN coatings was investigated at higher sliding speed and higher sliding distances than those in the literature. The coatings were deposited on AISI D2 cold-worked tool steel substrates using a magnetron sputtering system. The wear tests were performed at a sliding speed of 45 cm/s using a ball-on-disc method, and the wear area was investigated at seven different sliding distances (36–1,416 m). An Al₂O₃ ball was used as the counterpart material. The wear evolution was monitored using a confocal optical microscope and surface profilometer after each sliding test. The coefficient of friction and coefficient of wear were recorded with increasing sliding distance. It was found that the wear rate of the TiAlN coating decreases with sliding distance and it is much lower than that of TiN coating at longer sliding distance. This is due to the Al₂O₃ film formation at high temperature in the contact zone. Both coatings give similar coefficient of friction data during sliding with a slight increase in that of the TiAlN coating at high sliding distances due to the increasing alumina formation. When considering all results, the TiAlN coating is more suitable for hard machining applications.