Near-infrared emission spectrometry based on an acousto-optical tunable filter

A spectrometer has been constructed to detect the radiation emitted by thermally excited samples in the near-infrared spectral region extending from 1500 to 3000 nm. The instrument employs an acousto-optical tunable filter (AOTF) made of TeO2 and attains maximum sensitivity by making effective use of the two diffracted beams produced by the anisotropic AOTF. The full exploitation of the transmitted power of the monochromatic beams is reported for the first time and became possible because the detector does not saturate when employed for the acquisition of the weak emission signal in the NIR region, even when exposed to the total (nondiffracted) beam. Thus, modulation and lock-in-based detection can be employed to find the intensity of the diffracted beams superimposed on the nondiffracted beam. The resolution is slighted degraded in view of the small (approximately 10 nm) difference in the wavelength diffracted in the ordinary and extraordinary beams. The instrument has been evaluated in terms of signal-to-noise ratio, effect of sample thickness, and excitation temperature and for its potential in analytical applications in monitoring high-temperature kinetics, for qualitative identification of inorganic solids, for use with a closed cell to obtain spectra of species that evaporate at the temperatures (> 150 degrees C) necessary for sample excitation, and for quantitative purposes in the determination of soybean oil content in olive oil. The feasibility of near-infrared emission spectroscopy has been demonstrated together with some of its advantages over mid-infrared emission spectroscopy, such as greater tolerance to sample thickness, suitable signal-to-noise, and its use in the investigation of kinetic phenomena and phase transitions at high temperatures.     

Polarization holographic high-density optical data storage in bacteriorhodopsin film

Optical films containing the genetic variant bacteriorhodopsin BR-D96N were experimentally studied in view of their properties as media for holographic storage. Different polarization recording schemes were tested and compared. The influence of the polarization states of the recording and readout waves on the retrieved diffractive image's intensity and its signal-to-noise ratio were analyzed. The experimental results showed that, compared with the other tested polarization relations during holographic recording, the discrimination between the polarization states of diffracted and scattered light is optimized with orthogonal circular polarization of the recording beams, and thus a high signal-to-noise ratio and a high diffraction efficiency are obtained. Using a He-Ne laser (633 nm, 3 mW) for recording and readout, a spatial light modulator as a data input element, and a 2D-CCD sensor for data capture in a Fourier transform holographic setup, a storage density of 2 x 10(8) bits/cm2 was obtained on a 60 x 42 microm2 area in the BR-D96N film. The readout of encoded binary data was possible with a zero-error rate at the tested storage density.     

Analysis and observation of finite beam Bragg diffraction by a thick planar phase grating

A numerical-impulse-response technique for studying the propagation and diffraction of finite-width beams in planar phase gratings is described. It can account for both symmetric and asymmetric diffractions. The grating-length-to-beam-width ratio is shown to govern the extent of beam-profile distortion and selectivity sidelobe suppression. Trade-offs between diffraction efficiency and beam profile have also been demonstrated. Theoretical results have been verified by experimental observations in a planar waveguide geometry of diffracted beams that change from a single diffraction peak to multiple peaks as the grating-length-to-beam-width ratio increases.     

Spatial resolutions for applying photorefractive polymers to diffractive elements

Spatial resolutions of diffracted beams by photorefractive polymers are investigated in detail for applying the polymers to diffractive optical elements. The coupled wave equations for the four-wave mixing in photorefractive polymers and their solutions by applying the two-beam coupling approximation are derived taking the orientational enhancement effect into consideration. Characteristics of the diffraction efficiency of the polymers for the applied electric field, the incident angles of beams, the incident radiation intensity and the polarization are clarified. Furthermore, resolutions of diffracted images with the polymers are discussed by a numerical analysis from the viewpoint of the Bragg diffraction in a spatial frequency domain. An experiment with the TPD (tetra-phenyl-diphenyldiamine) acrylate based photorefractive polymers and the USAF test target is also performed to measure the spatial resolution of two-dimensional images diffracted by the polymer and to verify the calculated results. It is revealed that high resolution over 50 lp mm^?1 can be obtained with sufficient diffraction efficiency in the case of the polymer thickness of several 10 µm.     

混凝土表面开口裂缝对近表面声波影响

基于混凝土近表面不同波型的声速,分析开口裂缝对声波的影响。有限元仿真结果表明,激励源辐射的初始纵波P经裂缝端点衍射产生纵波P-P与横波P-T,P-T以一定的角度射向混凝土表面经模式转换产生纵波P-T-P;初始横波T在裂缝端点衍射产生纵波T-P与横波T-P;初始瑞利波R在裂缝端点衍射后除了产生纵波R-P与横波R-S外继续沿着固体表面传播(R-R)。在此基础上,基于变型波到达接收阵元的时刻定量检测裂缝的深度,检测结果较单面平测法具有更高的信噪比与检测精度,可辅助单面平测法更精确地定量检测混凝土开口裂缝的深度。     

Propagation analysis of self-convergent beam width and characterization of hard-edge diffracted beams

For a laser beam diffracted by a hard-edge aperture, propagation of the beam width, defined by the second-order moment of its irradiance distribution truncated according to the self-convergent-width criterion, obeys the familiar hyperbolic law. It is demonstrated numerically that, with the self-convergent-width approach, the beam-propagation parameters for three beam types (Gaussian, Hermite-Gaussian, and flattened Gaussian) diffracted by hard-edge apertures can be determined with the second-moment-based procedure that is recommended by the present draft standard only for unapertured laser beams.     

Linear diffraction grating interferometer with high alignment tolerance and high accuracy

We present an innovative structure of a linear diffraction grating interferometer as a long stroke and nanometer resolution displacement sensor for any linear stage. The principle of this diffractive interferometer is based on the phase information encoded by the ±1st order beams diffracted by a holographic grating. Properly interfering these two beams leads to modulation similar to a Doppler frequency shift that can be translated to displacement measurements via phase decoding. A self-compensation structure is developed to improve the alignment tolerance. LightTool analysis shows that this new structure is completely immune to alignment errors of offset, standoff, yaw, and roll. The tolerance of the pitch is also acceptable for most installation conditions. In order to compact the structure and improve the signal quality, a new optical bonding technology by mechanical fixture is presented so that the miniature optics can be permanently bonded together without an air gap in between. For the output waveform signals, a software module is developed for fast real-time pulse counting and phase subdivision. A laser interferometer HP5529A is employed to test the repeatability of the whole system. Experimental data show that within 15?mm travel length, the repeatability is within 15?nm.     

Two-dimensional Raman-Nath acousto-optic bistability by use of frequency feedback

From the frequency dependence of the optical transmission characteristics of Raman-Nath acoustic-optic diffraction, the dynamic equations and steady-state solutions of a two-dimensional Raman-Nath acousto-optic bistable system are derived. In this system, feedback is realized by use of a diffracted light beam to control the frequency of the acoustic-optic driver. The curves of light output versus input corresponding to several orders of the diffracted beams are obtained by theoretical analysis. They can all lead to bistability. The amount of hysteresis is a function of the order of the diffracted beam, the bias frequency, and the feedback coefficient. Experimental results are presented and compared with theoretical analyses.     

Viewing-zone enlargement method for sampled hologram that uses high-order diffraction

We demonstrate a method of enlarging the viewing zone for holography that has holograms with a pixel structure. First, aliasing generated by the sampling of a hologram by pixel is described. Next the high-order diffracted beams reproduced from the hologram that contains aliasing are explained. Finally, we show that the viewing zone can be enlarged by combining these high-order reconstructed beams from the hologram with aliasing.     

Vectorial four-wave mixing due to optical Kerr effect in polycrystalline CdTe

We study experimentally the polarization properties of the wave generated by means of degenerate four-wave mixing in polycrystalline CdTe using forward-box phase matching configuration and picosecond laser pulses with a wavelength of 1064 nm. The dependencies of the wave polarization generated due to the optical Kerr effect on the polarization combinations of the input beams are presented. We show that diffracted light polarization depends on the polarization of both recording beams, and the effect of each recording beam on the diffracted beam polarization is different depending on the mutual position of the recording beams and the probe beam. It was found that virtually any polarization of the generated beam could be obtained by proper choice of the recording and probe beam polarization. These results could make the polycrystalline media with third-order non-linearity a cheap and effective alternative to single crystals in non-linear devices for ultrafast all-optical control of polarization.     

Symmetric profile beams from waveguides with asymmetric grating couplers

An accurate method to analyze integrated optics waveguides with a grating is used to design diffractive gratings. A novel approach to produce symmetric diffracted beams is proposed. In this approach, we vary the grating duty cycle along the propagation direction. We demonstrate that this method results in symmetrical diffracted beam profiles.     

Use of energy dispersive method with tungsten carbide opposed anvil high pressure set-up

The use of energy dispersive method has been discussed to record the X-ray diffraction data from a tungsten carbide opposed anvil high pressure set-up. It is pointed out that a proper collimation of the incident and the diffracted beams can eliminate the scattering from the gasket material. This results in an appreciable improvement in the quality of the recorded diffraction data. The choice of the various parameters has been discussed. The data on sodium chloride are presented in support of this analysis.     

Observation of self-diffraction effect in acid blue 7 dye soaked gelatin films

Abstract

Permanent self-diffraction gratings are formed in red sensitive Acid blue 7 dye soaked gelatin films under illumination of an interference pattern by two linearly polarized beams from a He-Ne laser at 632.8 nm. Growth of the self-diffraction grating is monitored by measuring intensities of various diffraction orders. Systematic studies are carried out to investigate the influence of various parameters involved in diffraction efficiency of the grating such as time of exposure, concentration of dye in the gelatin-coated plate, intensity of interfering beams and intensity ratio of interfering beams. Efficient gratings with ten diffracted orders are formed. Several interesting observations are made by blocking one of the writing beams and an attempt is made to analyse these results.     

Holographic imaging and interferometry with non-Bragg diffraction orders on volume and surface-relief gratings in lithium niobate and photo-thermoplastic materials

The recording of holographic volume and surface-relief gratings in a photorefractive crystal using a photo-thermoplastic (PTP) holographic camera with an image-bearing signal beam leads to the appearance of two Bragg and two or more non-Bragg diffracted beams that show the transformed images in each beam (rotation and angular amplification of images). Using this real-time mode of interferometry, the hologram is retrieved with a deformed object beam, resulting in the appearance of fringes with a proper phase shift in each of four diffracted beams. This one-shot (one-exposure) phase-shifting interferometry results in clarification of the object wave-front information (for example, from surface deformation) and solution of the sign ambiguity problem. This procedure demonstrates that high-resolution holographic imaging of the PTP holographic camera static deformations in the order of ～0.1?mm can be revealed on the diffusion reflection surface. In addition, it was demonstrated that using the PTP materials could achieve holographic recording and imaging through phase aberration, with the image appearing in the non-Bragg diffraction order.     

Self-interferometric technique for visualization of phase patterns encoded onto a liquid-crystal display

We report a new self-interferometric technique for visualizing phase patterns that are encoded onto a phase-only liquid-crystal display (LCD). In our approach, the LCD generates both the desired object beam as well as the reference beam. Normally the phase patterns are encoded with a phase depth of 2pi radians, and all of the incident energy is diffracted into the first-order beam. However, by reducing this phase depth, we can generate an additional zero-order diffracted beam, which acts as the reference beam. We work at distances such that these two patterns spatially interfere, producing an interference pattern that displays the encoded phase pattern. This approach was used recently to display the phase vortices of helical Ince-Gaussian beams. Here we show additional experimental results and analyze the process.     

Influence of recording conditions on crossed-beam photorefractive gratings in doubly doped LiNbO3 crystals

The influence of the recording conditions, including the widths of the recording beams, the width ratio of the recording beams, and the recording angles, on the properties of crossed-beam photorefractive gratings in doubly doped LiNbO3 crystals is studied. A theoretical model that combines the band transport model with two-dimensional coupled-wave theory is proposed. The numerical calculations of the space-charge field, the intensity profiles of the diffracted beam, and the diffraction efficiency are presented.     

Spectrograph based on a single diffractive element for real-time measurement of circular dichroism

In this study, a novel and simple diffractive spectrographic method for real-time measurements of circular dichroism (CD) is considered from a theoretical and experimental approach. A demonstrator prototype of the CD spectrograph has been developed and its performance has been compared with a commercial phase-modulation CD spectrometer. The main element of the device is a polarization holographic grating, recorded in a thin photosensitive organic film, by two interfering opposite circularly polarized beams. A peculiarity of this grating is that the amplitude of the +1 (-1) order of diffraction is proportional to the right (left) circular polarization component of the incoming beam. Here we demonstrate that the CD spectrum of a specimen can be easily evaluated from the intensities of the diffracted beams. A white light beam passing through the specimen is diffracted from the grating and the intensities of the +/-1 orders of diffraction are measured. Due to the spectral selectivity of the grating, the CD at each wavelength can be evaluated at the same time using two linear array detectors.     

Directional laser generation and detection of ultrasound with arrays of optical fibers

Some aspects of the generation and detection of ultrasound with laser beams are presented. The objective of the study is (1) to present some experimental results on the generation of ultrasound with an array of optical fibers, (2) to discuss the possibility of generating directional surface waves with acousto-optic scanning in a very narrow frequency band, thus increasing the signal-to-noise ratio, and (3) to discuss the feasibility of the directional detection of ultrasound by using an array of optical fibers as a receiver, also with the goal of increasing the signal-to-noise ratio.     

Diffraction of Gaussian beams by periodic and aperiodic rulings

The diffraction of Gaussian beams by periodic and aperiodic rulings is considered. The theory of diffraction is based on the Rayleigh-Sommerfeld integral equation with Dirichlet conditions. The transmitted power and the normally diffracted energy are analyzed as a function of the beam radius. Two methods to determine the Gaussian beam radius by means of periodic and aperiodic lamellar gratings are proposed. One is based on the maximum and the minimum transmitted power, and the other one considers the normally diffracted energy. Small and large Gaussian beam radii can be treated with these two methods.     

Effects of Arbitrary Phase Shift on the Higher-order Self-diffraction in Absorptive Photorefractive Medium

Abstract

Interactions between optical beams incident upon and two higher-order self-diffracted beams generated within an absorptive photorefractive material are investigated by solving a set of coupled differential equations. The medium is assumed to be free of linear and circular birefringence. Arbitrary phase shift between the light grating and the refractive index grating is considered. It is shown that under favourable conditions, a significant amount of power may be transferred to the newly generated waves. Investigated are the effects of phase shift, thickness and absorption of the crystal, coupling constant and off-Bragg parameter on energy transfer to the higher-order diffracted beams. It is shown that in the case of phase-shift other than π/2, higher-order self-diffracted beams can be generated on both sides of the input beams. Coupled wave equations are solved numerically by a fourth-order Runge-Kutta method and results are presented in graphical form. This analysis is valid for the near collinear interacting beam geometry, i.e. in the case of large grating spacing.