Empirical model for the extraction system YCl3ErCl3HClH2ODI-(2-ethylhexyl)phosphoric acid—n-heptane

Equilibrium data were obtained for the extraction of the binary rare earth mixture yttrium chloride-erbium chloride from 2 kmol/m³ HClH₂O solutions by 1 kmol/m³ di(2-ethylhexyl)phosphoric acid in n-heptane. Total rare earth concentration in the aqueous phase was 0.5 kmol/m³. It was found that yttrium concentrations in the organic phase exhibit negative deviations whereas erbium concentrations exhibit positive deviations from ideality. Empirical correlations for predicting these deviations were developed. The separation factor was calculated.     

La2O2CO3 supported Ni-Fe catalysts for hydrogen production from steam reforming of ethanol

La2O2CO3 was prepared by calcination of La2 (CO3)3 in the air. Catalysts Ni-Fe/La2O2CO3 with different mole ratios of Ni to Fe, Ni/La2O2CO3 and Fe/La2O2CO3 were prepared by impregnation method. The catalytic properties were evaluated on steam reforming of ethanol (SRE) from 300 to 700 ℃ under atmospheric pressure and the samples were characterized by Brunauer-Emmett-Teller method (BET), X-ray diffraction (XRD) and temperature programmed reduction (TPR). The results showed that Ni-Fe bimetallic catalysts exh...     

Investigation on the amounts of Na2CO3 and sulphur to obtain pure Y2O2S and up-conversion luminescence of Y2O2S:Er

The process to prepare pure phase of hexagonal Y2O2S was investigated. Effect of mixed flux of Na2CO3 and S amounts was studied. The phase composition and morphology were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results showed that the single phase of Y2O2S with smooth morphology could not be obtained as the molar ratio of Y2O3, Na2CO3 and S was in the range of 1:(0.5-1):(2-3) until the molar ratio was increased to 1:1.5:4. Different Er3+ concentration doped Y2O2S...     

Up-conversion luminescence of Er~（3＋）-doped and Yb~（3＋）/Er~（3＋） co-doped 12CaO·7Al_2O_3 poly-crystals

The optical properties of Er3+-doped and Yb3+/Er3+ co-doped 12CaO·7Al2O3 (C12A7) poly-crystals, synthesized by high temperature solid state method, were investigated in detail. For Er3+-doped and Yb3+/Er3+ co-doped C12A7 poly-crystals, two main emission bands centered around 530/550 nm (green) and 660 nm (red) were observed under 980 nm diode laser excitation via an up-conversion process. The intensity of green up-conversion emission had a strong increase in Er3+ (1.0 mol.%, 1.5 mol.%, 3.0 mol.%), and the intensity ratio of red to green up-conversion emission had an increase in Yb3+ (1.0 mol.%, 2.0 mol.%, 10. 0 mol.%)/Er3+ (fixed at 1.0 mol.%). This detailed study of the up-conversion processes allowed us to identify the dominant up-conversion mechanisms in Er3+-doped and Yb3+/Er3+ co-doped C12A7 poly-crystals.     

Spectroscopic investigations of Gd3Sc2Ga3O12 garnet doped with Cr^3＋ and Nd^3＋ ions

Absorption, excitation and emission spectra as well as decay time measurements at 10, 77, and 300 K were performed for Ga₃Gd₃Sc₂O₁₂ garnet single-crystal doped with Cr³⁺ and Nd³⁺ ions. Strong reabsorption of Cr³⁺ emission by Nd³⁺ absorption lines was observed. The assignments of f–f and d–d transitions were proposed. The broad emission band of chromium ions is an indication that weak/intermediate crystal field strength is present at the Cr³⁺ site.     

Thermal expansion anomaly and spontaneous magnetostriction of Gd2Fe17 compound

Materials with negative thermal expansion have many practical applications. However, these materials are known in only several oxide systems, and when the negative thermal expansion occurs, the contraction is usually small and limited to a narrow temperature range beyond room temperature. For obtaining a compound with negative thermal expansion in broad temperature range, the structural and magnetic properties of Gd2Fe17 compound were investigated by means of X-ray diffraction and magnetization measurements. The Gd2Fe17 compound annealed at 1050 oC had a Th2Zn17-type structure. There existed an anisotropic strong spontaneous magnetostriction and a negative thermal expansion in Gd2Fe17 compound. The average thermal expansion coefficients was =-7.40×10-6/K in the temperature range of 294-453 K and =-1.80×10-5/K in 453-534 K, respectively. The spontaneous magnetostrictive deformation ωS decreased from 4.34×10-3 to near zero with temperature increasing from 294 to 572 K. The spontaneous linear deformation λc was much larger than λa at the same temperature below about 500 K.     

Vacuum ultraviolet excited photoluminescence properties of Gd2O2CO3：Eu^3＋ phosphor

The Gd2O2CO3：Eu^3＋ with type-Ⅱ structure phosphor was successfully synthesized via flux method at 400 ℃ and their photoluminescence properties in vacuum ultraviolet （VUV） region were examined. The broad and strong excitation bands in the range of 153-205 nm owing to the CO3^2- host absorption and charge transfer （CT） of Gd^3＋-O2^- were observed for Gd2O2CO3：Eu^3＋. Under 172 nm excitation, Gd2O2CO3：Eu^3＋ exhibited strong red emission with good color purity, indicating Eu^3＋ ions located at low symmetry sites and the chromaticity coordination of luminescence for Gd2O2CO3：Eu^3＋ was （x=0.652, y=0.345）. The photoluminescence quenching concentration of Eu^3＋ excited by 172 nm for Gd2O2CO3：Eu^3＋ was about 5%. Gd2O2CO3：Eu^3＋ would be a potential VUV-excited red phosphor applied in mercury-free fluorescent lamps.     

Luminescence properties of YAl3（BO3）4 phosphors doped with Eu^3＋ ions

YAl3 （BO3）4： Eu^3＋ phosphors were prepared by the conventional solid state reaction. The phase structure and morphology were investigated by X-ray diffraction （XRD） and scanning electron microscope （SEM）. Doping YAl3（BO3）4： Eu^3＋ phosphors with concentration of Eu^3＋ ions of 0, 2, 5, 8 and 10 mol% were studied and their luminescent properties at room temperature were discussed. The excitation spectrum of Y0.95Eu0.05Al3（BO3）4 was composed of a broad band centered at about 252 nm and a group of lines in the longer wavelength region. In the emission spectra, the peak wavelength was about 614 nm under a 252 nm UV excitation. The optimal doping concentration of Eu^3＋ ions in YAl3（BO3）4： Eu^3＋ phosphors was 8 mol%.     

Study on Sulfation of CeO2/γ-Al2O3 Sorbent in Simulated Flue Gas

It is well known that sulfur dioxide(SO2) , morethan50%of which arise fromcombustion of fossil fu-els ,are precursors of acidrain andtheir emission pos-es a global threat tothe atmosphere .Environmental a-gencies have ,therefore ,regulated emissions of SO…     

Investigation on pumping oxygen characteristics of （Bi2O3）0.73（Y2O3）0.27 solid electrolyte

（Bi2O3）0.73（Y2O3）0.27 fine powders prepared by wet chemical precipitation method were cold isostatically pressed to form solid electrolyte tubes, and sintered at 900 ℃ for 10 h in the air. Their pumping oxygen characteristics in non-dehydrated Ar gas were investigated, where a ZrO2 （Y2O3 stabilized） oxygen sensor was used to measure the oxygen partial pressure Po2. The results showed that the Po2 value reached magnitudes of 1×10^-2-1×10^-10 Pa at the applied pumping oxygen voltage of 0.5 V, 1×10^-37-1×10^-27 Pa at 1.0 V and 1×10^-53-1×10^47 Pa at 2.0 V within the temperature range from 550 to 650 ℃. Moreover, no cracks were found in the tested solid electrolyte tubes. Thus, the Bi2O3-Y2O3 system might be used in solid electrolyte oxygen pump for purifying gases.     

Preparation and Characterization of Red Luminescent Ca0.8 Zn0.2 TiO3 ： Pr3 ＋ , Na^＋ Nanophosphor

Nanophosphor with the nominal composition of Ca0.8 Zn0.2 TiO3 ： Pr3 ＋ , Na^＋ （CZTOPN） was synthesized at relatively low temperature by the sol-gel method. Metal ions were dispersed by citric acid in ethylene glycol solvent and then react with Ti（OC4H9）4 to form sol and gel. The decomposition process of the precursor, and crystallization and particle size of CZTOPN were examined by thermal analysis （TG-DSC）, powder X-ray diffraction （XRD）, and scan election microscopy （SEM）. Results of TG-DSC and XRD reveal that the composition of Ca0.8 Zn0.2 TiO3 ： Pr3 ＋ , Na^＋ changes with the sintering temperature. SEM data indicate that the diameter of particles is under 50 nm even if the sintering temperature increases to 1000 ℃. In contrast to a solid state reaction, the excitation spectra of samples synthesized by the sol-gel method shift blue about 10 nm and the emission intensity at 617 nm increases significantly.     

Preparation, spectral characteristics and photocatalytic activity of Eu-doped WO3 nanoparticles

Eu³⁺-WO₃ nanoparticles were successfully prepared by the modified method of Pechini. The prepared samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM), and UV-vis spectroscopy. Results showed that the Eu³⁺-WO₃ nanoparticles, which had an average external diameter of 10–25 nm, were composed of the different shapes of puncheon and catenary after being pretreated by pH, pressure vessal, and surfactant. Moreover, structural transformation matrix contained different crystals of anorthic and orthorhombic structure. The photocatalytic activities of the nanoparticles were evaluated by photocatalytic decomposition of rhodamine B. Eu³⁺-WO₃ nanoparticles were more efficient than WO₃ and TiO₂ on sunlight use ratio. Photocatalysis experiments indicated that the Eu³⁺-WO₃ nanoparticles exhibited the highest photocatalytic activity.     

Three-photon-excited fluorescence of Tb-doped CaO-Al2O3-SiO2 glass by femtosecond laser irradiation

A near infrared to visible blue, green, and red upconversion luminescence in a Tb^3＋-doped CaO-Al2O3-SiO2 glass was studied, which was excited using 800 nm femtosecond laser irradiation. The upconversion luminescence was attributed to ^5D3→^7F5, ^5D3→^7F4, ^5D3→^7F3, ^5D4→^7F6, ^5D4→^7F5, ^5D4→^7F4, and ^5D4→^7F3 transitions of Tb^3＋. The relationship between upconversion luminescence intensity and the pump power indicated that a three-photon simultaneous absorption process was dominant in this upconversion luminescence. The intense red, green, and blue upconversion luminescence of Tb^3＋-doped CaO-Al2O3-SiO2 glass may be potentially useful in developing three-dimensional display applications.     

Paramagnetic Anisotropy of CdGd2（WO4） 4-δ Single Crystal

CdGd2 （WO4）4 -δ single crystal was grown using the Czochralski＇s method. The crystal structure was tetragonal seheelite with lattice parameters a = b = 0.5203 nm and c = 1. 1359 nm. There were vacancies of （WO4）^2- , therefore, there were some Gd^2＋ ions. Langevin paramagnetism and anisotropy were observed from the δ-T curves at room temperature. The susceptibility X//was 3.5018×10^-3, and X⊥ was 3.4403× 10^-2. The anisotropy was also observed in the electron spin resonance （ESR） experiments. The anisotropic Land6 factors were g//= 2. 1333 and g~ = 2. 8411. The direction of easy magnetization was in the α-b plane. Anisotropic paramagnetic Curie constants C//and C⊥ were not only related to macroscopic a that was observed through the experiment, but were also related to J⊥ and J//, which were the microscopic quantum numbers of the Gd^2＋ and Gd^3｜ ions. Based on the detailed analyses, the proportion of 36.8% of Gd^3＋ ions to 63.2% of Gd^2＋ ions in the Gd ions of the CdGd2（WO4）4-δ crystal was calculated, and δ was 0.638 in the single crystal.     

Yb_2SiO_5稀土硅酸盐环境障涂层研究进展

环境障涂层体系历经三代的发展,稀土硅酸盐因其具有低热膨胀系数、优良的抗水氧腐蚀性能与相稳定性,且与中间层莫来石化学相容性好,已成为研究热点。本文重点论述稀土硅酸盐Yb_2SiO_5环境障涂层的制备方法、涂层形貌、相结构影响以及裂纹机制、抗高温水蒸气腐蚀及抗CMAS腐蚀性能的研究进展。并指出了以Yb_2SiO_5为代表的稀土硅酸盐体系值得关注的问题及未来环境障涂层的发展趋势。     

Phase control of magnetron sputtering deposited Gd2O3 thin films as high-κ gate dielectrics

Gd2O3 thin films as high-κ gate dielectrics were deposited directly on Si（001） substrates by magnetron sputtering at a pressure of 1.3 Pa and different temperatures. X-ray diffraction results revealed that all the films grown from 450 to 570 ℃ were crystalline, and the Gd2O3 thin films consisted of a mixture of cubic and monoclinic phases. The growth temperature was a critical parameter for the phase constituents and their relative amount. Low temperature was favorable for the formation of cubic phase while higher temperature gave rise to more monoclinic phase. All the Gd2O3 thin films grown from different temperatures exhibited acceptable electrical properties, such as low leakage current density （JL） of 10-5 A/cm^2 at zero bias with capacitance equivalent SiO2 thickness in the range of 6-13 nm. Through the comparison between films grown at 450 and 570 ℃, the existence of monoclinic phase caused an increase in JL by nearly one order of magnitude and a reduction of effective dielectric constant from 17 to 9.     

Partial oxidation of methane on Ni/CeO2-ZrO2/γ-Al2O3 prepared using different processes

The influences of CeO2-ZrO2 and γ-Al2O3 mixing methods on the catalytic activity and stability of partial oxidation of methane （POM） were investigated over Ni/Ce0.7Zr0.3O2-Al2O3 catalysts. The catalysts were characterized by XRD, TPR, H2-chemsorption, and TG-DTA. For fresh catalysts, the results showed that the salt precursor mixing catalyst （ATOM） presented better performance than the catalysts prepared by the precipitator mixing method （MOL） and the powder mechanically mixing method （MECH）. The result of XRD suggested that the interaction between CeO2-ZrO2 and Al2O3 in ATOM sample was stronger than the others, which led to more lattice defects and thereby better initial activity. Moreover, the MECH sample had the best stability and the least coke deposition in 24 h stability tests. The results of TPR and H2-chemsorption indicated that the intimate contact of Ni-Al in MECH sample enhanced the ability of resisting coke deposition and metal sintering.     

Anodic behaviour of the Pb–Co3O4 composite coating in copper electrowinning

The electrochemical and corrosion properties of Pb–Co₃O₄ (about 3% Co) composite anode for copper electrowinning without additives as well as in the presence of two combinations of organic additives in the electrolyte have been investigated and compared with those of Pb–Sb 5.85% anode. The formation of PbO₂ layer on the surface of these electrodes was traced by cyclic voltametric measurements using rotating disc electrode (RDE) method. The Pb–Co₃O₄ composite anode shows a depolarizing effect on the process of oxygen evolution as compared to Pb–Sb anode. The corrosion rate of Pb–Co₃O₄ anode during prolonged polarization is approximately 6.7 times lower than that of Pb–Sb anode. The influence of the tested organic additives on the anodic behaviour of both anodes is negligible.     

Synthesis and Spectral Properties of Nd^3＋： Gd3Ga5O12 Nanopowder for Transparent Laser Ceramics

Nd^3＋： Gd3Ga5O12（Nd ： GGG） nanopowder for transparent laser ceramics was synthesized using sol-gel method. XRD, SEM, and fluorescence spectrum were used to study the properties of Nd^3＋ ：Gd3Ga5O12 nanopowder. XRD patterns of samples show that it has a cubic structure. Meanwhile, pure Nd：GGG crystals were obtained at 1000 ℃ for 12 h. SEM photographs show that dispersed, uniform, ball-like Nd：GGG nanopowder is obtained. Both XRD and SEM results show that the crystallization degree and the grain size increase with the increase in calcining temperature. Analysis of fluorescence spectrum shows that fluorescence emission occurs at 1062.7 nm, which is the result of Nd^3＋ （^4F3/2→^4I11/2） transition. Homogenous Nd ： GGG nanopewder with a small grain size synthesized using the sol-gel method is favorable for sintering the transparent ceramic, which proves that the nanopewder obtained is suitable as a precursor for preparing GGG transparent ceramics.     

Liquid–liquid extraction of yttrium using primene-JMT from acidic sulfate solutions

The liquid–liquid extraction of yttrium(III) from sulfate medium using primene-JMT is investigated with regard to extractant concentration, diluent type, equilibrium pH and time, temperature, and extraction isotherm. Aliphatic kerosene diluents were preferred compared to aromatic diluents because of higher extraction, shorter equilibrium time and good phase separation. Increasing temperature had a negative effect on yttrium(III) extraction. Quantitative yttrium(III) extraction efficiency was achieved at room temperature within 5 min using three stages of extraction with 0.4 M primene-JMT from a synthetic yttrium solution at pH 1.5 (0.2 M H₂SO₄) at a phase ratio of 1:1. A mechanism for extraction is suggested. The proposed separation of yttrium(III) from rare earth concentrate obtained from alkaline leaching of Egyptian monazite is outlined.