Synthesis and electrochemical performances of Li3V2(PO4)3/(Ag + C) composite cathode

Li₃V₂(PO₄)₃, Li₃V₂(PO₄)₃/C and Li₃V₂(PO₄)₃/(Ag + C) composites as cathodes for Li ion batteries are synthesized by carbon-thermal reduction (CTR) method and chemical plating reactions. The microstructure and morphology of the compounds are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The Li₃V₂(PO₄)₃/(Ag + C) particles are 0.5-1 μm in diameters. As compared to Li₃V₂(PO₄)₃, Li₃V₂(PO₄)₃/C, the Li₃V₂(PO₄)₃/(Ag + C) composite cathode exhibits high discharge capacity, good cycle performance (140.5 mAh g⁻¹ at 50th cycle at 1 C, 97.3% of initial discharge capacity) and rate behavior (120.5 mAh g⁻¹ for initial discharge at 5 C) for the fully delithiated (3.0-4.8 V) state. Electrochemical impedance spectroscopy (EIS) measurements show that the carbon and silver co-modification decreases the charge transfer resistance of Li₃V₂(PO₄)₃/(Ag + C) cathode, and improves the conductivity and boosts the electrochemical performance of the electrode.     

Synthesis and performance of Li3(V1−xMgx)2(PO4)3 cathode materials

In order to search for cathode materials with better performance, Li₃(V_1−xMg_x)₂(PO₄)₃ (0, 0.04, 0.07, 0.10 and 0.13) is prepared via a carbothermal reduction (CTR) process with LiOH·H₂O, V₂O₅, Mg(CH₃COO)₂·4H₂O, NH₄H₂PO₄, and sucrose as raw materials and investigated by X-ray diffraction (XRD), scanning electron microscopic (SEM) and electrochemical impedance spectrum (EIS). XRD shows that Li₃(V_1−xMg_x)₂(PO₄)₃ (x = 0.04, 0.07, 0.10 and 0.13) has the same monoclinic structure as undoped Li₃V₂(PO₄)₃ while the particle size of Li₃(V_1−xMg_x)₂(PO₄)₃ is smaller than that of Li₃V₂(PO₄)₃ according to SEM images. EIS reveals that the charge transfer resistance of as-prepared materials is reduced and its reversibility is enhanced proved by the cyclic votammograms. The Mg²⁺-doped Li₃V₂(PO₄)₃ has a better high rate discharge performance. At a discharge rate of 20 C, the discharge capacity of Li₃(V_0.9Mg_0.1)₂(PO₄)₃ is 107 mAh g⁻¹ and the capacity retention is 98% after 80 cycles. Li₃(V_0.9Mg_0.1)₂(PO₄)₃//graphite full cells (085580-type) have good discharge performance and the modified cathode material has very good compatibility with graphite.     

Temperature-controlled microwave solid-state synthesis of Li3V2(PO4)3 as cathode materials for lithium batteries

Monoclinic Li₃V₂(PO₄)₃ can be rapidly synthesized at 750 °C for 5 min (MW5m) by using temperature-controlled microwave solid-state synthesis method (TCMS). The carbon-free sample MW5m presents well electrochemical properties. In the cut-off voltage 3.0-4.3, MW5m presents a charge capacity 132 mAh g⁻¹, almost equivalent to the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹), and discharge capacity 126.4 mAh g⁻¹. In the cut-off voltage 3.0-4.8 V, MW5m shows an initial discharge capacity of 183.4 mAh g⁻¹, near to the theoretical discharge capacity. In the cycle performance, the capacity fade of Li₃V₂(PO₄)₃ is dependent on the cut-off voltage and the preparation method.     

Synthesis and improved electrochemical performances of porous Li3V2(PO4)3/C spheres as cathode material for lithium-ion batteries

Spherical Li₃V₂(PO₄)₃/C composites are synthesized by a soft chemistry route using hydrazine hydrate as the spheroidizing medium. The electrochemical properties of the materials are investigated by galvanostatic charge-discharge tests, cyclic voltammograms and electrochemical impedance spectrum. The porous Li₃V₂(PO₄)₃/C spheres exhibit better electrochemical performances than the solid ones. The spherical porous Li₃V₂(PO₄)₃/C electrode shows a high discharge capacity of 129.1 and 125.6 mAh g⁻¹ between 3.0 and 4.3 V, and 183.8 and 160.9 mAh g⁻¹ between 3.0 and 4.8 V at 0.2 and 1 C, respectively. Even at a charge-discharge rate of 15 C, this material can still deliver a discharge capacity of 100.5 and 121.5 mAh g⁻¹ in the potential regions of 3.0-4.3 V and 3.0-4.8 V, respectively. The excellent electrochemical performance can be attributed to the porous structure, which can make the lithium ion diffusion and electron transfer more easily across the Li₃V₂(PO₄)₃/electrolyte interfaces, thus resulting in enhanced electrode reaction kinetics and improved electrochemical performance.     

Synthesis and electrochemical properties of Na-doped Li3V2(PO4)3 cathode materials for Li-ion batteries

Na-doped Li_3−xNa_xV₂(PO₄)₃/C (x = 0.00, 0.01, 0.03, and 0.05) compounds have been prepared by using sol-gel method. The Rietveld refinement results indicate that single-phase Li_3−xNa_xV₂(PO₄)₃/C with monoclinic structure can be obtained. Among three Na-doped samples and the undoped one, Li_2.97Na_0.03V₂(PO₄)₃/C sample has the highest electronic conductivity of 6.74 × 10⁻³ S cm⁻¹. Although the initial specific capacities for all Na-doped samples have no much enhancement at the current rate of 0.2 C, both cycle performance and rate capability have been improved. At the 2.0 C rate, Li_2.97Na_0.03V₂(PO₄)₃/C presents the highest initial capacity of 118.9 mAh g⁻¹ and 12% capacity loss after 80 cycles. The partial substitution of Li with Na (x = 0.03) is favorable for electrochemical rate and cyclic ability due to the enlargement of Li₃V₂(PO₄)₃ unit cells, optimizing the particle size and morphology, as well as resulting in a higher electronic conductivity.     

Li3V2(PO4)3/C composite as an intercalation-type anode material for lithium-ion batteries

The carbon coated monoclinic Li₃V₂(PO₄)₃ (LVP/C) powder is successfully synthesized by a carbothermal reduction method using crystal sugar as the carbon source. Its structure and physicochemical properties are investigated using X-ray diffraction (XRD), scanning electron microscopy, high-resolution transmission electron microscopy and electrochemical methods. The LVP/C electrode exhibits stable reversible capacities of 203 and 102 mAh g⁻¹ in the potential ranges of 3.0-0.0 V and 3.0-1.0 V versus Li⁺/Li, respectively. It is identified that the insertion/extraction of Li⁺ undergoes a series of two-phase transition processes between 3.0 and 1.6 V and a single phase process between 1.6 and 0.0 V. The ex situ XRD patterns of the electrodes at various lithiated states indicate that the monoclinic structure can still be retained during charge-discharge process and the insertion/deinsertion of lithium ions occur reversibly, which provides an excellent cycling stability with high energy efficiency.     

A fast synthesis of Li3V2(PO4)3 crystals via glass-ceramic processing and their battery performance

A synthesis of Li₃V₂(PO₄)₃ being a potential cathode material for lithium ion batteries was attempted via a glass-ceramic processing. A glass with the composition of 37.5Li₂O-25V₂O₅-37.5P₂O₅ (mol%) was prepared by a melt-quenching method and precursor glass powders were crystallized with/without 10 wt% glucose in N₂ or 7%H₂/Ar atmosphere. It was found that heat treatments with glucose at 700 °C in 7%H₂/Ar can produce well-crystallized Li₃V₂(PO₄)₃ in the short time of 30 min. The battery performance measurements revealed that the precursor glass shows the discharge capacity of 14 mAh g⁻¹ at the rate of 1 μA cm⁻² and the glass-ceramics with Li₃V₂(PO₄)₃ prepared with glucose at 700 °C in 7%H₂/Ar show the capacities of 117-126 mAh g⁻¹ (∼96% of the theoretical capacity) which are independent of heat treatment time. The present study proposes that the glass-ceramic processing is a fast synthesizing route for Li₃V₂(PO₄)₃ crystals.     

Synthesis of plate-like Li3V2(PO4)3/C as a cathode material for Li-ion batteries

Plate-like Li₃V₂(PO₄)₃/C composite is synthesized via a solution route followed by solid-state reaction. The Li₃V₂(PO₄)₃/C plates are 40-100 nm in thicknesses and 2-10 μm in lengths. TEM images show that a uniform carbon layer with a thickness of 5.3 nm presents on the surfaces of Li₃V₂(PO₄)₃ plates. The apparent Li-ion diffusion coefficient of the plate-like Li₃V₂(PO₄)₃/C is calculated to be 2.7 × 10⁻⁸ cm² s⁻¹. At a charge-discharge rate of 3 C, the plate-like Li₃V₂(PO₄)₃/C exhibits an initial discharge capacity of 125.2 and 133.1 mAh g⁻¹ in the voltage ranges of 3.0-4.3 and 3.0-4.8 V, respectively. After 500 cycles, the electrodes still can deliver a discharge capacity of 111.8 and 97.8 mAh g⁻¹ correspondingly, showing a good cycling stability.     

Synthesis, structure and electrochemical Li insertion behaviour of Li2Ti6O13 with the Na2Ti6O13 tunnel-structure

Li₂Ti₆O₁₃ has been prepared from Na₂Ti₆O₁₃ by Li ion exchange in molten LiNO₃ at 325 °C. Chemical analysis and powder X-ray diffraction study of the reaction product respectively indicate that total Na/Li exchange takes place and the Ti-O framework of the Na₂Ti₆O₁₃ parent structure is kept under those experimental conditions. Therefore, Li₂Ti₆O₁₃ has been obtained with the mentioned parent structure. An important change is that particle size is decreased significantly which is favoring lithium insertion. Electrochemical study shows that Li₂Ti₆O₁₃ inserts ca. 5 Li per formula unit in the voltage range 1.5-1.0 V vs. Li⁺/Li, yielding a specific discharge capacity of 250 mAh g⁻¹ under equilibrium conditions. Insertion occurs at an average equilibrium voltage of 1.5 V which is observed for oxides and titanates where Ti(IV)/Ti(III) is the active redox couple. However, a capacity loss of ca. 30% is observed due to a phase transformation occurring during the first discharge. After the first redox cycle a high reversible capacity is obtained (ca. 160 mAh g⁻¹ at C/12) and retained upon cycling. Taking into consideration these results, we propose Li₂Ti₆O₁₃ as an interesting material to be further investigated as the anode of lithium ion batteries.     

Characteristics of Li3V2(PO4)3/C powders prepared by ultrasonic spray pyrolysis

Li₃V₂(PO₄)₃ and Li₃V₂(PO₄)₃/C powders are prepared by ultrasonic spray pyrolysis from spray solutions with and without sucrose. The precursor powders have a spherical shape and the crystal structure of V₂O₃ irrespective of the concentration of sucrose in the spray solution. The powders post-treated at 700 °C have the pure crystal structure of the Li₃V₂(PO₄)₃ phase irrespective of the concentration of sucrose in the spray solution. The Li₃V₂(PO₄)₃ powders prepared from the spray solution without sucrose have a non-spherical shape and hard aggregation. However, the Li₃V₂(PO₄)₃/C powders prepared from the spray solution with sucrose have a spherical shape and non-aggregation characteristics. The Li₃V₂(PO₄)₃ powders prepared from the spray solution without sucrose have a low initial discharge capacity of 122 mAh g⁻¹. However, the Li₃V₂(PO₄)₃/C powders prepared from the spray solutions with 0.1, 0.3, and 0.5 M sucrose have initial discharge capacities of 141, 130, and 138 mAh g⁻¹, respectively. After 25 cycles, the discharge capacities of the powders formed from the spray solutions with and without 0.1 M sucrose are 70% and 71% of the initial discharge capacities, respectively.     

Non-stoichiometry in thin film dilute tungsten bronzes: MxWO3−y

Thin films of tungsten trioxide have been prepared in various ways which give rise to different optical behaviour. The white light optical absorption versus inserted lithium atom concentration is measured and followed as a function of time. The influence of post-deposition treatment in oxygen at 300°C is studied, and the results of these experiments support the key role of non-stoichiometry. Previous thin film structural studies are re-enforced here by a structural investigation of evaporated films using the atomic force microscope. These optical-insertion data are interpreted by means of a model which proposes that electron trapping occurs at crystalline shear plane boundaries (which account for the non-stoichiometry). The extent and rate of trapping is modelled, and the experimental results are consistent with the trapping rate being proportional to the lithium atom concentration in the films. The importance of minimising non-stoichiometry in electrochromic devices and in specimens of material for use in physical measurements is made clear.     

High-rate cathodes based on Li3V2(PO4)3 nanobelts prepared via surfactant-assisted fabrication

In this work, we have synthesized monoclinic Li₃V₂(PO₄)₃ nanobelts via a single-step, solid-state reaction process in a molten hydrocarbon. The as-prepared Li₃V₂(PO₄)₃ nanoparticles have a unique nanobelt shape and are ∼50-nm thick. When cycled in a voltage range between 3.0 V and 4.3 V at a 1C rate, these unique Li₃V₂(PO₄)₃ nanobelts demonstrate a specific discharge capacity of 131 mAh g⁻¹ (which is close to the theoretical capacity of 132 mAh g⁻¹) and stable cycling characteristics.     

Synthesis and performance of carbon-coated Li3V2(PO4)3 cathode materials by a low temperature solid-state reaction

The carbon-coated monoclinic Li₃V₂(PO₄)₃ (LVP) cathode materials can be synthesized by a low temperature solid-state reaction route. The influences of different heat treatments on the LVP have been investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical methods. In the range of 3.0-4.3 V, both LVP/C electrodes present good rate capability and excellent cyclic performance. It is found that the sample (LVP1/C) prepared by the two-step heat treatment with pre-sintering at 350 °C delivers the initial discharge capacity of 99.8 mAh g⁻¹ at 10 C charge-discharge rate and still retains 95.8 mAh g⁻¹ after 300 cycles. For the sample (LVP2/C) synthesized by the one-step heat treatment, 95.9 and 90.0 mAh g⁻¹ are obtained in the 1st and 300th cycles at 10 C rate, respectively. Our results based on the XRD patterns and the SEM images suggest that the good rate capability and cyclic performance may be owing to the pure phases, small particles, large specific surface areas and residual carbon. In the range of 3.0-4.8 V, compared with the LVP2/C, the LVP1/C also exhibits better performance.     

Structural,electronic, dynamical and thermodynamic properties of Ca10(PO4)6(OH)2 and Sr10(PO4)6(OH)2: First-principles study

Density functional theory (DFT) with optPBE-vdW functional is used to simulate the structural, electronic, dynamical and thermodynamic properties of Ca₁₀(PO₄)₆(OH)₂(Ca-HA) and Sr₁₀(PO₄)₆(OH)₂(Sr-HA). The calculated structural properties within optPBE-vdW functional is found to yield better agreement with the experimental results, which indirectly suggests the important role of weak hydrogen bond in this crystal. The calculated electronic properties indicate that Ca-HA and Sr-HA are insulator materials with indirect band gap of 5.52 eV and 5.10 eV, respectively. The detailed dynamical properties of two apatites are obtained by the linear-response approach. With replacement of Ca by Sr, the librational mode of OH group decreases from 612 cm^?1 to 569 cm^?1, the stretching mode of OH group increases from 3614.5 cm^?1–3649.9 cm^?1, which is consistent with the experimental results. Finally, some phonon related thermodynamic properties, such as Helmholtz free energy F, internal energy E, entropy S and heat capacity C_V of Sr-HA and Ca-HA are studied according to the phonon calculations within the harmonic approximation. The present calculation results of two apatites with optPBE-vdW functional are in good agreement with the existing experimental.     

Improved electrochemical performances of 9LiFePO4·Li3V2(PO4)/C composite prepared by a simple solid-state method

9LiFePO₄·Li₃V₂(PO₄)₃/C is synthesized via a carbon thermal reaction using petroleum coke as both reduction agent and carbon source. The as-prepared material is not a simple mixture of LiFePO₄ (LFP) and Li₃V₂(PO₄)₃ (LVP), but a composite possessing two phases: one is V-doped LFP and the other is Fe-doped LVP. The typical structure enhances the electrical conductivity of the composite and improves the electrochemical performances. The first discharge capacity of 9LFP·LVP/C in 18650 type cells is 168 mAh g⁻¹ at 1 C (1 C_9LFP·LVP/C = 166 mA g⁻¹), and exhibits high reversible discharge capacity of 125 mAh g⁻¹ at 10 C even after 150 cycles. At the temperature of −20 °C, the reversible capacity of 9LFP·LVP/C can maintain 75% of that at room temperature.     

Li1.2Zr1.9Ca0.1(PO4)3, a room-temperature Li-ion solid electrolyte

Substitution of 5% of Zr by Ca in LiZr₂(PO₄)₃ transforms the structure to that of rhombohedral NASICON to give a room-temperature bulk Li-ion conductivity σ_Li ≈ 1.2 × 10⁻⁴ S cm⁻¹, which is comparable to that of Li_1.3Ti_1.7Al_0.3(PO₄)₃ now being used as a solid Li-ion separator in test cells of novel Li-ion batteries.     

Synthesis, characterization and application of Li3Fe2(PO4)3 nanoparticles as cathode of lithium-ion rechargeable batteries

This work introduces a new method to synthesize Li₃Fe₂(PO₄)₃ nanoparticles in the nanopowder form and study its electrochemical performance by cyclic voltammetry and battery tests. Li₃Fe₂(PO₄)₃ is synthesized by the gel combustion method based on polyvinyl alcohol (PVA) as gel making agent. The optimum conditions of the synthesis include 8 wt% PVA, 0.34 wt% lithium slat, 1 wt% iron salt, 0.57 wt% ammonium dihydrogen phosphate, ethanol-water 50:50 as solvent, 675 °C combustion temperature and 4 h combustion time. Characterization of the samples is performed by the scanning electron microscopy (SEM), transmission electron microscopy (TEM), EDX analysis, XRD patterns, BET specific surface area and DSL size distribution. In the optimum conditions, a nanopowder is obtained that consisting of uniform nanoparticles with an average diameter of 70 nm. The optimized sample shows 12.5 m² g⁻¹ specific surface areas. Cyclic voltammetry (CV) studies show that the synthesized compound has good reversibility and high cyclic stability. The CV results are confirmed by the battery tests. The obtained results show that the synthesized cathodic material has high practical discharge capacity (average 125.5 mAh g⁻¹ approximately same with its theoretical capacity 128.2 mA h⁻¹) and long cycle life.     

Ni3(PO4)2-coated Li[Ni0.8Co0.15Al0.05]O2 lithium battery electrode with improved cycling performance at 55 °C

To improve the cycling performance of LiNi_0.8Co_0.15Al_0.05O₂ at 55 °C, a thin Ni₃(PO₄) layer was homogeneously coated onto the cathode particle via simple ball milling. The morphology of the Ni₃(PO₄)₂-coated LiNi_0.8Co_0.15Al_0.05O₂ particle was characterized using SEM and TEM analysis, and the coating thickness was found to be approximately 10-20 nm. The Ni₃(PO₄)₂-coated LiNi_0.8Co_0.15Al_0.05O₂ cell showed improved lithium intercalation stability and rate capability especially at high C rates. This improved cycling performance was ascribed to the presence of Ni₃(PO₄)₂ on the LiNi_0.8Co_0.15Al_0.05O₂ particle, which protected the cathode from chemical attack by HF and thus suppressed an increase in charge transfer resistance. Transmission electron microscopy of extensively cycled particles confirmed that the particle surface of the Ni₃(PO₄)₂-coated LiNi_0.8Co_0.15Al_0.05O₂ remained almost undamaged, whereas pristine particles were severely serrated. The stabilization of the host structure by Ni₃(PO₄)₂ coating was also verified using X-ray diffraction.     

Electrochemical properties of Li1.4Al0.4Ti1.6(PO4)3 synthesized by a co-precipitation method

Sub-micron Li_1.4Al_0.4Ti_1.6(PO₄)₃ (LATP) ceramic powder is synthesized by a co-precipitation method which can be applied for mass production. A pure Nasicon phase is confirmed by X-ray diffraction analysis and the primary particle size of the product is 200-500 nm. The sinterability of LATP is investigated and the relative density of 97% reached at a sintering temperature as low as 900 °C for 6 h. The bulk lithium ionic conductivity of the sintered pellet is 2.19 × 10⁻³ S cm⁻¹, and a total conductivity of 1.83 × 10⁻⁴ S cm⁻¹ is obtained.