Structural and Dielectric Properties of Ag(Nb0.8Ta0.2)1−xSbxO3 (x≤0.08) Ceramics

Sb₂O₅ were selected to substitute (Nb_0.8Ta_0.2)₂O₅ and the effects of Sb substitution on the dielectric properties of Ag(Nb_0.8Ta_0.2)O₃ ceramics were studied. The perovskite Ag(Nb_0.8Ta_0.2)_{1− x} Sb _x O₃ ceramics showed no obvious change with x value being no more than 0.08, and the pseudoperovskite unit cell parameters a = c , b and monoclinic angle β decrease with Sb concentration increasing. The dielectric properties of Ag(Nb_0.8Ta_0.2)_{1− x} Sb _x O₃ ceramics were found to be affected greatly by the substitution of Sb for Nb/Ta. The ɛ value of Ag(Nb_0.8Ta_0.2)_{1− x} Sb _x O₃ ceramics sintered at their densified temperature increased from 480 to 825 with x from 0 to 0.08, the tan δ value decreased sharply from 0.0065 to 0.0023 (at 1 MHz) with x increasing from 0 to 0.04, and then kept a stable lower tan δ value ∼0.0024 with x to 0.08. The temperature coefficient of capacitance values continuously decreased from a positive value of 1450 ppm/°C for x =0 to a negative value of −38.52 ppm/°C for x =0.08.     

Microstructure and Microwave Dielectric Properties of (1−x)Ca(Mg1/3Ta2/3)O3/xCaTiO3 Ceramics

Dense (1− x )Ca(Mg_1/3Ta_2/3)O₃/ x CaTiO₃ ceramics (0.1≤ x ≤0.9) were prepared by a solid-state reaction process. The crystal structures and microstructures were characterized by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. Single-phase solid solutions were obtained in the entire composition range. Long-range 1:2 ordering of B-site cations and oxygen octahedra tilting lead to the monoclinic symmetry with space group P 2₁/ c for x =0.1. For x above 0.1, the long-range ordering was destroyed and the crystal structure became the orthorhombic with space group Pbnm . The microwave dielectric properties showed a strong dependence on the composition and microstructure. The dielectric constant and temperature coefficient of resonant frequency increased nonlinearly as the CaTiO₃ content increased while the Qf values decreased approximately linearly. Good combination of microwave dielectric properties was obtained at x =0.45, where ɛ_r=45.1, Qf =34 800 GHz, and τ_f=17.4 ppm/°C.     

Effects of Ca/Ti Cosubstitution upon Microwave Dielectric Characteristics of CaSmAlO4 Ceramics

(Ca_{1+ x} Sm_{1− x} )(Al_{1− x} Ti _x )O₄ (0≤ x ≤0.4) ceramics were synthesized by solid-state reaction method and their microstructures and microwave dielectric properties were investigated. X-ray diffraction analysis and energy-dispersive X-ray analysis indicated that the matrix phase was a solid solution with a composition represented by the chemical formula (Ca_{1+ x} Sm_{1− x} ) (Al_{1− x} Ti _x )O₄ and minor amount of (Ca,Sm)(Al,Ti)O₃ secondary phase was detected. Ca/Ti cosubstitution could significantly improve the microwave dielectric characteristics of CaSmAlO₄ ceramics, and the excellent microwave dielectric characteristics were obtained in the modified ceramics as ɛ_r=19–23, Q × f =49 100–118 700 GHz, and τ_f=−15–15 ppm/°C.     

Low-Temperature Sintering and Dielectric Properties of Ag(Nb,Ta)O3 Composite Ceramics

The sintering behavior and dielectric properties of perovskite Ag(Nb_{1− x} Ta _x )O₃ (0 < x < 1) solid solutions and two-phase composite assemblages were explored. A small amount of CuO (1 wt%) was used for liquid-phase sintering and led to high densification at temperatures <950°C. The temperature coefficient of capacitance, TCC, was adjusted by varying the Nb:Ta ratio within the solid-solution series and by creating composite microstructures. Two-phase assemblages consisting of Ag(Nb_3/4Ta_1/4)O₃ and Ag(Nb_1/4Ta_3/4)O₃ were synthesized to achieve a temperature-stable dielectric material for high-frequency applications. The composite dielectric with CuO addition had an average dielectric constant of 390 and a Q × f factor of 410 GHz at 2 GHz, with a stable TCC (0 to −180 ppm/°C) in the temperature range from −20° to +60°C. In addition, process compatibility with a silver conductor was confirmed by high-frequency ring-resonator measurements and microstructural characterization. The Ag(Nb_{1− x} Ta _x )O₃ solid solutions and composites are promising candidates as embedded capacitors for radio-frequency/microwave applications.     

Low-Loss Microwave Dielectrics Using Mg2(Ti1−xSnx)O4 (x=0.01–0.09) Solid Solution

Low-loss ceramics having the chemical formula Mg₂(Ti_{1− x} Sn _x )O₄ for x ranging from 0.01 to 0.09 have been prepared by the conventional mixed oxide route and their microwave dielectric properties have been investigated. X-ray powder diffraction patterns indicate the corundum-structured solid solutions for the prepared compounds. In addition, lattice parameters, which linearly increase from 8.4414 to 8.4441 Å with the rise of x from 0.01 to 0.09, also confirm the forming of solid solutions. By increasing x from 0.01 to 0.05, the Q × f of the specimen can be tremendously boosted from 173 000 GHz to a maximum 318 000 GHz. A fine combination of microwave dielectric properties (ɛ_r∼15.57, Q × f ∼318 000 GHz at 10.8 GHz, τ_f∼−45.1 ppm/°C) was achieved for Mg₂(Ti_0.95Sn_0.05)O₄ ceramics sintered at 1390°C for 4 h. Ilmenite-structured Mg(Ti_0.95Sn_0.05)O₃ (ɛ_r∼16.67, Q × f ∼275 000 GHz at 10.3 GHz, τ_f∼−53.2 ppm/°C) was detected as a second phase. The presence of the second phase, however, would cause no significant variation in the dielectric properties of the specimen, because the second phase properties are very similar to the primary phase. These unique properties, in particular, low ɛ_r and high Q × f , can be utilized as a very promising dielectric material for ultra-high-frequency applications.     

Effect of Cation Substitution and Non-Stoichiometry on the Microwave Dielectric Properties of Sr(B'0.5Ta0.5)O3 [B'=Lanthanides] Perovskites

The Sr(B'_0.5Ta_0.5)O₃ ceramics where B'=La, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Y, Er, and Yb have been prepared by the conventional solid-state ceramic route and their microwave dielectric properties have been investigated. The structure and microstructure of the ceramics have been characterized by X-ray diffraction and scanning electron microscope techniques. The relative permittiviy (ɛ_r) varies linearly with B'-site ionic radii, except for La, and the temperature coefficient of resonant frequency (τ_f) varies linearly with the tolerance factor. The Sr(B'_0.5Ta_0.5)O₃ ceramics have ɛ_r in the range 25.9–32, Q _u× f =4500–54 300 GHz, and τ_f=−79 to −42 ppm/°C. A slight deviation from stoichiometry affects the dielectric properties of these double perovskites. Partial substitution of Ba for Sr could tune the dielectric properties. Addition of rutile (TiO₂) lowered the sintering temperature and improved the dielectric properties of Sr(B'_0.5Ta_0.5)O₃ ceramics.     

High Q Microwave Dielectric Ceramics in (Ni1−x Znx)Nb2O6 System

(Ni_{1− x} Zn _x )Nb₂O₆, 0≤ x ≤1.0, ceramics with >97% density were prepared by a conventional solid-state reaction, followed by sintering at 1200°–1300°C (depending on the value of x ). The XRD patterns of the sintered samples (0≤ x ≤1.0) revealed single-phase formation with a columbite ( Pbcn ) structure. The unit cell volume slightly increased with increasing Zn content ( x ). All the compositions showed high electrical resistivity (ρ_dc=1.6±0.3 × 10¹¹Ω·cm). The microwave (4–5 GHz) dielectric properties of (Ni_{1− x} Zn _x )Nb₂O₆ ceramics exhibited a significant dependence on the Zn content and to some extent on the morphology of the grains. As x was increased from 0 to 1, the average grain size monotonically increased from 7.6 to 21.2 μm and the microwave dielectric constant (ɛ'_r) increased from 23.6 to 26.1, while the quality factors ( Q _u× f ) increased from 18 900 to 103 730 GHz and the temperature coefficient of resonant frequency (τ_f) increased from −62 to −73 ppm/°C. In the present work, we report the highest observed values of Q _u× f =103 730 GHz, and ɛ'_r=26.1 for the ZnNb₂O₆-sintered ceramics.     

Microwave Dielectric Properties of CaTiO3-CaAl1/2Nb1/2O3 Ceramics Doped with Li3NbO4

The microwave dielectric properties of CaTi_{1− x} (Al_1/2Nb_1/2) _x O₃ solid solutions (0.3 ≤ x ≤ 0.7) have been investigated. The sintered samples had perovskite structures similar to CaTiO₃. The substitution of Ti⁴⁺ by Al³⁺/Nb⁵⁺ improved the quality factor Q of the sintered specimens. A small addition of Li₃NbO₄ (about 1 wt%) was found to be very effective for lowering sintering temperature of ceramics from 1450–1500° to 1300°C. The composition with x = 0.5 sintered at 1300°C for 5 h revealed excellent dielectric properties, namely, a dielectric constant (ɛ_r) of 48, a Q × f value of 32 100 GHz, and a temperature coefficient of the resonant frequency (τ_f) of −2 ppm/K. Li₃NbO₄ as a sintering additive had no harmful influence on τ_f of ceramics.     

Microwave Characteristics of A(B3+1/2B5+1/2)O3 Ceramics (A = Ba, Ca, Sr; B3+= La, Nd, Sm, Yb; B5+= Nb, Ta)

Dielectric properties of A(B³⁺_1/2B⁵⁺_1/2)O₃ (A = Ba, Ca, Sr; B³⁺= La, Nd, Sm, Yb; B⁵⁺= Nb, Ta) ceramics have been investigated at microwave frequencies. Sr(B³⁺_1/2B⁵⁺_1/2)O₃ and Ca(B³⁺_1/2B⁵⁺_1/2)O₃ ceramics have relative dielectric constants (ε _r ) above 20 and negative temperature coefficients of resonant frequency (T _f ). In the group of Ba(B³⁺_1/2B⁵⁺_1/2)O₃ ceramics, T _f changes from + 118 ppm/° to nearly zero according to the kinds of B-site ions. Among the ceramics investigated, Sr(Sm_1/2Ta_1/2)O₃ ceramics have the highest Q values at microwave frequencies. For Sr(Sm_1/2Ta_1/2)O₃ ceramics Q = 7000, ε _r = 27.7, and T _f =−62.5 ppm/° at 8.5 GHz. The microstructure of Sr(Sm_1/2Ta_1/2)O₃ ceramics is composed of a matrix of the ternary compound (Sr-Sm-Ta-O system) and secondary phase grains of the binary compound (Sm-Ta-O system).     

Structure and Microwave Dielectric Characteristics of Ca1+xNd1−xAl1−xTixO4 Ceramics

CaNdAlO₄ microwave dielectric ceramics were modified by Ca/Ti co-substitution, and their dielectric characteristics were evaluated along with their structure and microstructures. Ca_{1+ x} Nd_{1− x} Al_{1− x} Ti _x O₄ ( x =0, 0.025, 0.05, 0.10, 0.15, 0.20) ceramics with the relative density of over 95% theoretical density were obtained by sintering at 1400°–1450°C in air for 3 h, where the K₂NiF₄-type solid solution single phase was determined from the compositions of x <0.20, while a small amount of CaTiO₃ secondary phase was detected for x =0.20. With Ca/Ti co-substitution in CaNdAlO₄ ceramics, the dielectric constant (ɛ_r) increased with increasing x , and the temperature coefficient of resonant frequency (τ_f) was adjusted from negative to positive, while the Q × f ₀ value increased significantly at first and reached an extreme value at x =0.025 and the maximum at x =0.15. The best combination of microwave dielectric characteristics were achieved at x =0.15 (ɛ_r=19.5, Q × f ₀=93 400 GHz, τ_f=−2 ppm/°C). The improvement of the Q × f ₀ value primarily originated from the reduced interlayer polarization with Ca/Ti co-substitution, while the decreased tolerance factor, the subsequent increased interlayer stress, and the appearance of CaTiO₃ secondary phase brought negative effects upon the Q × f ₀ value.     

Effect of V2O5 Doping on the Sintering and Dielectric Properties of M-Phase Li1+x−yNb1−x−3yTix+4yO3 Ceramics

The effect of the addition of V₂O₅ on the structure, sintering and dielectric properties of M -phase (Li_{1+ x − y} Nb_{1− x −3 y} Ti _x +4 _y )O₃ ceramics has been investigated. Homogeneous substitution of V⁵⁺ for Nb⁵⁺ was obtained in LiNb_{0.6(1− x )}V_{0.6 x} Ti_0.5O₃ for x ≤ 0.02. The addition of V₂O₅ led to a large reduction in the sintering temperature and samples with x = 0.02 could be fully densified at 900°C. The substitution of vanadia had a relatively minor adverse effect on the microwave dielectric properties of the M -phase system and the x = 0.02 ceramics had [alt epsilon]_r= 66, Q × f = 3800 at 5.6 GHz, and τ_f= 11 ppm/°C. Preliminary investigations suggest that silver metallization does not diffuse into the V₂O₅-doped M -phase ceramics at 900°C, making these materials potential candidates for low-temperature cofired ceramic (LTCC) applications.     

Effect of BaWO4 on the Microwave Dielectric Properties of Ba(Mg1/3Ta2/3)O3 Ceramics

Physical and microwave dielectric properties of complex perovskite Ba(Mg_1/3Ta_2/3)O₃ ceramics have been investigated as a function of the amount of BaWO₄ in the temperature range from 20° to 80°C at 10.5 GHz. Up to 0.05 mol BaWO₄ addition, the lattice constant ratio ( c/a ), ordering parameter, apparent density, and unloaded Q all increase, due to the increase in the substitution of Ta⁵⁺ ions of Ba(Mg_1/3Ta_2/3)O₃ by W⁶⁺ ions from the melted BaWO₄ at above 1430°C. With further addition of BaWO_4, the unloaded Q decreases, due to an increase of the BaWO₄ phase. The temperature coefficient of resonant frequency (TCF) can be controlled by the volume mixture rule of Ba(Mg_1/3Ta_2/3)O₃ and BaWO₄. When 0.09 mol BaWO₄ is added, TCF becomes 0 ppm/°C.     

The Effect of Dopants on the Dielectric Properties of Ba(B'1/2Ta1/2)O3 (B'=La, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Y, Yb, and In) Microwave Ceramics

Low-loss dielectric ceramics based on Ba(B'_1/2Ta_1/2)O₃ (B'=La, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Y, Yb, and In) complex perovskites have been prepared by the solid-state ceramic route. The dielectric properties (ɛ_r, Q _u, and τ_f) of the ceramics have been measured in the frequency range 4–6 GHz by the resonance method. The resonators have a relatively high dielectric constant and high quality factor. Most of the compounds have a low coefficient of temperature variation of the resonant frequencies. The microwave dielectric properties have been improved by the addition of dopants and by solid solution formation. The solid solution Ba[(Y_{1− x} Pr _x )_1/2Ta_1/2]O₃ has x =0.15, with ɛ_r=33.2, Q _u× f =51,500 GHz, and τ_f≈0. The microwave dielectric properties of Ba(B'_1/2Ta_1/2)O₃ ceramics are found to depend on the tolerance factor ( t ), ionic radius, and ionization energy.     

Structure and Microwave Dielectric Properties of Hexagonal Ba[Ti1−x(Ni1/2W1/2)x]O3 Ceramics

Microwave dielectric ceramics with the composition of Ba[Ti_{1− x} (Ni_1/2W_1/2) _x ]O₃ ( x =0.4–0.6) were prepared by a solid-state reaction method. The evolution of the crystalline phases was investigated by X-ray powder diffraction analysis. A cubic-to-hexagonal phase transition occurred between 1000° and 1300°C. The phase transition is irreversible; thus, the hexagonal phase remains stable at room temperature. The X-ray powder diffraction data for x =0.5 were refined using the Rietveld method. It was identified as a h -BaTiO₃-type hexagonal perovksite with the space group of P 6₃/ mmc . It also reveals that random occupancy of Ti⁴⁺ and W⁶⁺ ions occurs in the B-site substructures, whereas Ni²⁺ ions exclusively occupy the octahedral site in the corner-sharing octahedron. The dielectric properties of dense-sintered ceramics were characterized at microwave frequencies. With an increase in x from 0.4 to 0.6, the Q × f value increased from 26 700 to 42 000 GHz, whereas ɛ_r decreased from 29.8 to 20.0, and τ_f from +6.5 to −9.9 ppm/°C.     

Microwave Characteristics of (Pb,Ca)(Fe,Nb,Sn)O3 Dielectric Materials

The dielectric properties of (Pb_{1− x} Ca _x ){(Fe_1/2Nb_1/2)_{1– y} Sn _y }O₃ solid solutions, where 0.4 lessthan equal tox ≤ 0.6, y = 0.05, 0.1, have been investigated at microwave frequencies. The replacement of Fe³⁺/Nb⁵⁺ by Sn⁴⁺ at the B–site of the perov-skite structure considerably improves the loss quality factor Q and does not remarkably affect the dielectric constant epsilon_r and the temperature coefficient of resonant frequency tau_f. The tau_f value of nearly 0 ppm/°C can be realized for x= 0.55. New high-quality dielectric ceramics having epsilon_r of 85.3-89.9,Qf values of 7510-8600 GHz, and τ_f of 0-9 ppm/°C were obtained at 1150°C for 3 h sintering in air. The influence of the sintering atmosphere on dielectric properties was also investigated.     

Phase Relations and Dielectric Properties in the Bi2O3–ZnO–Ta2O5 System

Dielectric properties and phase formation of Bi-based pyrochlore ceramics were evaluated for the Bi₂O₃–ZnO–Ta₂O₅ system. The compositional range r Bi₂(Zn_1/3Ta_2/3)₂O₇· (1− r )(Bi_3/2Zn_1/2)(Zn_1/2Ta_3/2)O₇ (0 ≤ r ≤ 1) in Bi₂O₃–ZnO–Ta₂O₅ was investigated to determine the relative solubility of BZT cubic (α-BZT, r = 0) and the pseudo-orthorhombic (β-BZT, r = 1) end members. It was found that extrinsic factors, such as kinetically limited phase formation and bismuth loss, contribute to apparent phase boundaries in addition to thermodynamic stability of each phase. Considering this, the locations of true phase boundaries were r < 0.30 and r ≥ 0.74 for α and β phases, respectively. Dielectric constants between 58 and 80 and low dielectric loss (tan δ < 0.003) were measured for the complete compositional range. The temperature coefficient of capacitance was controlled by composition, which was found to be <30 ppm/°C at the edge of β-phase solid solution. In addition to the excellent dielectric properties these materials can be sintered at low temperatures, which make Bi-based pyrochlores promising candidates for high-frequency electronic applications.     

Effects of Calcium Substitution on the Structural and Microwave Dielectric Characteristics of [(Pb1−xCax)1/2La1/2](Mg1/2Nb1/2)O3 Ceramics

The effects of calcium substitution on the structural and microwave dielectric characteristics of [(Pb_{1− x} Ca _x )_1/2La_1/2](Mg_1/2Nb_1/2)O₃ ceramics (with x = 0.01–0.5) were investigated. All the materials were observed to have an ordered A(B_1/2^'B_1/2^")O₃-type perovskite structure; however, the space group of the structure changed from Fm 3 m to Pa 3 as the calcium content increased to x = 0.1, and then from Pa 3 to R 3¯ at the x = 0.5 composition. During the structural evolution, the lattice parameter of the perovskite cell decreased linearly, and the dielectric constant ( k ) also decreased, from k = 80 to k = 38. However, the product of the quality factor and the resonant frequency ( Q × f ) increased from 50 000 GHz to 90 000 GHz as the calcium content increased. Also, the temperature coefficient of resonant frequency (τ_ƒ) gradually changed from 120 ppm/°C to −40 ppm/°C as the calcium content increased. At the x = 0.3 composition, a combination of properties— k ∼ 50, Q × f ∼ 86 000 GHz, and τ_ƒ∼ 0 ppm/°C—can be obtained.     

Ordered Structure and Dielectric Properties of Lanthanum-Substituted Ba(Mg1/3Ta2/3)O3

Both 1:2 and 1:1 ordered structures form in the perovskite solid solutions of La-substituted BMT Ba_{1− x} La _x (Mg_{(1+ x )/3}Ta_{(2− x )/3})O₃, sintered at 1600°C. The 1:2 ordered structure exists in the composition range 0.0 ≤ x ≤ 0.12, while that of 1:1 ordered structure exists in a wider composition range 0.04 ≤ x ≤ 1.0. Two ordered phases coexist in 0.04 ≤ x ≤ 0.12. High-resolution micrographs indicate that 1:2 and 1:1 ordered domains coexist in one grain. The ordering parameter of 1:2 phase decreases with x , yet that of 1:1 phase increases with x . Both increase with soak time. Variations in ordering are discussed in terms of cation occupancy and crystal chemistry. The quality factor increases with x , reaches a maximum, then decreases with x . The dielectric constant increases with x first, and levels off.     

High-Q Microwave Dielectrics in the (Mg1−xCox)2TiO4 Ceramics

The microwave dielectric properties and the microstructures of (Mg_{1− x} Co _x )₂TiO₄ ceramics prepared by the conventional solid-state route were investigated. Lattice parameters were also measured for specimens with different x . The formation of solid solution (Mg_{1− x} Co _x )₂TiO₄ ( x =0.02–0.1) was confirmed by the X-ray diffraction patterns, energy dispersive X-ray analysis, and the lattice parameters measured. By increasing x from 0 to 0.05, the Q × f of the specimen can be tremendously boosted from 150 000 GHz to a maximum of 286 000 GHz. A fine combination of microwave dielectric properties (ɛ_r∼15.7, Q × f ∼286 000 GHz at 10.4 GHz, τ_f∼−52.5 ppm/°C) was achieved for (Mg_0.95Co_0.05)₂TiO₄ ceramics sintered at 1390°C for 4 h. Ilmenite-structured (Mg_0.95Co_0.05)TiO₃ was detected as a second phase. The presence of the second phase would cause no significant variation in the dielectric properties of the specimen because it possesses compatible properties compared with that of the main phase. In addition, only a small deviation in the dielectric properties was monitored for specimens with x =0.04–0.05 at 1360°–1420°C. It not only provides a wide process window but also ensures an extremely reliable material proposed as a very promising dielectric for low-loss microwave and millimeter wave applications.     

Phase Structure and Electrical Properties of (K0.48Na0.52)(Nb0.95Ta0.05)O3-LiSbO3 Lead-Free Piezoelectric Ceramics

(1− x )(K_0.48Na_0.52)(Nb_0.95Ta_0.05)O₃– x LiSbO₃ [(1− x )KNNT− x LS] lead-free piezoelectric ceramics were prepared by the conventional solid-state sintering method. A morphotropic phase boundary (MPB) between orthorhombic and tetragonal phases was identified in the composition range of 0.03< x <0.05. The ceramics near the MPB exhibit a strong compositional dependence and enhanced electrical properties. The (1− x )KNNT– x LS ( x =0.04) ceramics exhibit good electrical properties ( d ₃₃=250 pC/N, k _p=45.1%, k _t =46.3%, T _c=348°C, T _{o − t} =74°C, P _r=25.9 μC/cm², E _c=10.7 kV/cm, ɛ_r∼1352, tan δ∼3%). These results show that (1− x )KNNT– x LS ceramic is a promising lead-free piezoelectric material.