Catalytic properties of Co<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles for rechargeable Li/air batteries

Three types of Co₃O₄ nanoparticles are synthesized and characterized as a catalyst for the air electrode of a Li/air battery. The shape and size of the nanoparticles are observed using scanning electron microscopy and transmission electron microscopy analyses. The formation of the Co₃O₄ phase is confirmed by X-ray diffraction. The electrochemical property of the air electrodes containing Co₃O₄ nanoparticles is significantly associated with the shape and size of the nanoparticles. It appears that the capacity of electrodes containing villiform-type Co₃O₄ nanoparticles is superior to that of electrodes containing cube- and flower-type Co₃O₄ nanoparticles. This is probably due to the sufficient pore spaces of the villiform-type Co₃O₄ nanoparticles.     

Effective Utilization of the Catalytically Active Phase: NH<Subscript>3</Subscript> Oxidation Over Unsupported and Supported Co<Subscript>3</Subscript>O<Subscript>4</Subscript>

Abstract  

The performance of pellets of unsupported and silica-supported Co₃O₄ in the ammonia oxidation was investigated as a function of the particle size to investigate the utilization of the catalytically active phase in these materials. The obtained activity in terms of ammonia conversion over the silica-supported Co₃O₄ is higher compared to the conversion over the unsupported Co₃O₄, despite a lower cobalt oxide loading and more severe diffusional limitations. The effectiveness factor for the silica-supported catalyst is slightly lower than the effectiveness factor for the unsupported catalyst in the form of pellets of similar size. However, the effective utilization of cobalt within the catalyst is higher for the silica-supported catalyst, mainly due to the higher dispersion of the catalytically active phase.     

Structure and electrochemical characterization of LiNi<Subscript>0.3</Subscript>Co<Subscript>0.3</Subscript>Mn<Subscript>0.3</Subscript>Fe<Subscript>0.1</Subscript>O<Subscript>2</Subscript> cathode for lithium secondary battery

A lithium insertion material having the composition LiNi_0.3Co_0.3Mn_0.3Fe_0.1O₂ was synthesized by simple sol-gel method. The structural and electrochemical properties of the sample were investigated using X-ray diffraction spectroscopy (XRD) and the galvanostatic charge-discharge method. Rietvelt analysis of the XRD patterns shows that this compound can be classified as α-NaFeO₂ structure type (R3m; a=2.8689(5) Å and 14.296(5) Å in hexagonal setting). Rietvelt fitting shows that a relatively large amount of Fe and Ni ion occupy the Li layer (3a site) and a relatively large amount of Li occupies the transition metal layer (3b site). LiNi_0.3Co_0.3Mn_0.3Fe_0.1O₂ when cycled in the voltage range 4.3–2.8 V gives an initial discharge capacity of 120 mAh/g, and stable cycling performance. LiNi_0.3Co_0.3Mn_0.3Fe_0.1O₂ in the voltage range 2.8–4.5 V has a discharge capacity of 140 mAh/g, and exhibits a significant loss in capacity during cycling. Ex-situ XRD measurements were performed to study the structure changes of the samples after cycling between 2.8–4.3 V and 2.8–4.5 V for 20 cycles. The XRD and electrochemical results suggested that cation mixing in this layered structure oxide could be causing degradation of the cell capacity.     

Effect of reaction conditions on the catalytic performance of Co<Subscript>9</Subscript>Fe<Subscript>3</Subscript>Bi<Subscript>1</Subscript>Mo<Subscript>12</Subscript>O<Subscript>51</Subscript> in the oxidative dehydrogenation of n-butene to 1,3-butadiene

Oxidative dehydrogenation of n-butene to 1,3-butadiene over Co₉Fe₃Bi₁Mo₁₂O₅₁ catalyst was conducted in a continuous flow fixed-bed reactor. The effect of reaction conditions (steam/n-butene ratio, reaction temperature, and space velocity) on the catalytic performance of Co₉Fe₃Bi₁Mo₁₂O₅₁ was investigated. Steam played an important role in decreasing contact time, suppressing total oxidation of n-butene, and removing coke during the reaction. Yield for 1,3-butadiene showed a volcano-shaped curve with respect to steam/n-butene ratio. The compensation between thermodynamic effect and kinetic effect led to a volcano-shaped curve of 1,3-butadiene yield with respect to reaction temperature. The Co₉Fe₃Bi₁Mo₁₂O₅₁ catalyst showed the best catalytic performance at a certain value of space velocity. The optimum steam/n-butene ratio, reaction temperature, and gas hourly space velocity were found to be 15, 420 °C, and 675 h⁻¹, respectively.     

LiNi<Subscript>0.4</Subscript>Co<Subscript>0.3</Subscript>Mn<Subscript>0.3</Subscript>O<Subscript>2</Subscript> thin film electrode by aerosol deposition

LiNi_0.4Co_0.3Mn_0.3O₂ thin film electrodes are fabricated from LiNi_0.4Co_0.3Mn_0.3O₂ raw powder at room temperature without pretreatments using aerosol deposition that is much faster and easier than conventional methods such as vaporization, pulsed laser deposition, and sputtering. The LiNi_0.4Co_0.3Mn_0.3O₂ thin film is composed of fine grains maintaining the crystal structure of the LiNi_0.4Co_0.3Mn_0.3O₂ raw powder. In the cyclic voltammogram, the LiNi_0.4Co_0.3Mn_0.3O₂ thin film electrode shows a 3.9-V anodic peak and a 3.6-V cathodic peak. The initial discharge capacity is 44.6 μAh/cm², and reversible behavior is observed in charge-discharge profiles. Based on the results, the aerosol deposition method is believed to be a potential candidate for the fabrication of thin film electrodes.     

Ni-Co bimetallic catalyst for CH<Subscript>4</Subscript> reforming with CO<Subscript>2</Subscript>

A co-precipitation method was employed to prepare Ni/Al₂O₃-ZrO₂, Co/Al₂ O₃-ZrO₂ and Ni-Co/Al₂O₃-ZrO₂ catalysts. Their properties were characterized by N₂ adsorption (BET), thermogravimetric analysis (TGA), temperature-programmed reduction (TPR), temperature-programmed desorption (CO₂-TPD), and temperature-programmed surface reaction (CH₄-TPSR and CO₂-TPSR). Ni-Co/Al₂O₃-ZrO₂ bimetallic catalyst has good performance in the reduction of active components Ni, Co and CO₂ adsorption. Compared with mono-metallic catalyst, bimetallic catalyst could provide more active sites and CO₂ adsorption sites (C + CO₂ = 2CO) for the methane-reforming reaction, and a more appropriate force formed between active components and composite support (SMSI) for the catalytic reaction. According to the CH₄-CO₂-TPSR, there were 80.9% and 81.5% higher CH₄ and CO₂ conversion over Ni-Co/Al₂O₃-ZrO₂ catalyst, and its better resistance to carbon deposition, less than 0.5% of coke after 4 h reaction, was found by TGA. The high activity and excellent anti-coking of the Ni-Co/Al₂O₃-ZrO₂ catalyst were closely related to the synergy between Ni and Co active metal, the strong metal-support interaction and the use of composite support.     

Structural characterization and electrochemical properties of Co<Subscript>3</Subscript>O<Subscript>4</Subscript> anode materials synthesized by a hydrothermal method

Cobalt oxide [Co₃O₄] anode materials were synthesized by a simple hydrothermal process, and the reaction conditions were optimized to provide good electrochemical properties. The effect of various synthetic reaction and heat treatment conditions on the structure and electrochemical properties of Co₃O₄ powder was also studied. Physical characterizations of Co₃O₄ are investigated by X-ray diffraction, scanning electron microscopy, and Brunauer-Emmett-Teller [BET] method. The BET surface area decreased with values at 131.8 m²/g, 76.1 m²/g, and 55.2 m²/g with the increasing calcination temperature at 200°C, 300°C, and 400°C, respectively. The Co₃O₄ particle calcinated at 200°C for 3 h has a higher surface area and uniform particle size distribution which may result in better sites to accommodate Li⁺ and electrical contact and to give a good electrochemical property. The cell composed of Super P as a carbon conductor shows better electrochemical properties than that composed of acetylene black. Among the samples prepared under different reaction conditions, Co₃O₄ prepared at 200°C for 10 h showed a better cycling performance than the other samples. It gave an initial discharge capacity of 1,330 mAh/g, decreased to 779 mAh/g after 10 cycles, and then showed a steady discharge capacity of 606 mAh/g after 60 cycles.     

A Novel Process for Renewable Methane Production: Combining Direct Air Capture by K<Subscript>2</Subscript>CO<Subscript>3</Subscript>/Alumina Sorbent with CO<Subscript>2</Subscript> Methanation over Ru/Alumina Catalyst

CO₂ methanation over supported ruthenium catalysts is considered to be a promising process for carbon capture and utilization and power-to-gas technologies. In this work 4% Ru/Al₂O₃ catalyst was synthesized by impregnation of the support with an aqueous solution of Ru(OH)Cl₃, followed by liquid phase reduction using NaBH₄ and gas phase activation using the stoichiometric mixture of CO₂ and H₂ (1:4). Kinetics of CO₂ methanation reaction over the Ru/Al₂O₃ catalyst was studied in a perfectly mixed reactor at temperatures from 200 to 300 °C. The results showed that dependence of the specific activity of the catalyst on temperature followed the Arrhenius law. CO₂ conversion to methane was shown to depend on temperature, water vapor pressure and CO₂:H₂ ratio in the gas mixture. The Ru/Al₂O₃ catalyst was later tested together with the K₂CO₃/Al₂O₃ composite sorbent in the novel direct air capture/methanation process, which combined in one reactor consecutive steps of CO₂ adsorption from the air at room temperature and CO₂ desorption/methanation in H₂ flow at 300 or 350 °C. It was demonstrated that the amount of desorbed CO₂ was practically the same for both temperatures used, while the total conversion of carbon dioxide to methane was 94.2–94.6% at 300 °C and 96.1–96.5% at 350 °C.     

Nanocasting Synthesis of Mesostructured Co<Subscript>3</Subscript>O<Subscript>4</Subscript> via a Supercritical CO<Subscript>2</Subscript> Deposition Method and the Catalytic Performance for CO Oxidation

Abstract  

We demonstrate a supercritical CO₂ (scCO₂) deposition method to synthesize mesostructured Co₃O₄ with crystalline walls using SBA-15 as the hard template. By variation of the scCO₂ pressure, randomly organized nanorods or a highly ordered mesoporous structure of Co₃O₄ is obtained after only one filling operation. The catalytic tests show that the randomly organized Co₃O₄ nanorods display excellent activity for CO oxidation with the complete conversion of CO even at room temperature, while neither the ordered mesoporous nor bulk Co₃O₄ is active at this low-temperature, demonstrating the important role of Co₃O₄ morphology in catalysis.     

Preparation and Characterization of LiNi<Subscript>0.8</Subscript>Co<Subscript>0.2</Subscript>O<Subscript>2</Subscript> Synthesized by an Emulsion Drying Method

A layered LiNi_0.8Co_0.2O₂ solid solution, which is a promising cathode material for secondary lithium batteries, was successfully synthesized by an emulsion drying method. Because electrochemical properties significantly depend on the conditions of the synthesis, the calcination temperature was carefully determined on the basis of X-ray diffraction and TG studies. The prepared cathodes were characterized by means of SEM, BET, X-ray diffraction, Rietveld refinement, cyclic voltammetry and a charge-discharge experiment. From the Rietveld analysis, it was found that powder calcined at 800 °C for 12 h exhibits a well ordered and lower cation mixed layered structure than the others. The cyclic voltammetry experiment shows that phase transformation can be suppressed considerably by increasing the calcination temperature to 800 °C. The highest discharge capacity of 188.4 mA h g⁻¹ was obtained from the sample prepared at 800 °C. Furthermore, a high capacity retention ratio of 88.1% was found for the initial value after 50 cycles at a constant current density of 40 mA g⁻¹ between 2.7 V_Li/Li⁺ and 4.3 V_Li/Li⁺. In the rate capability test, the cathode delivered a higher discharge capacity of 153.1 mA h g⁻¹ at a 4 C (800 mA g⁻¹) rate.     

Facile synthesis of nano-Li<Subscript>4</Subscript> Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> for high-rate Li-ion battery anodes

One of the most promising anode materials for Li-ion batteries, Li₄Ti₅O₁₂, has attracted attention because it is a zero-strain Li insertion host having a stable insertion potential. In this study, we suggest two different synthetic processes to prepare Li₄Ti₅O₁₂ using anatase TiO₂ nanoprecursors. TiO₂ powders, which have extraordinarily large surface areas of more than 250 m² g^-1, were initially prepared through the urea-forced hydrolysis/precipitation route below 100°C. For the synthesis of Li₄Ti₅O₁₂, LiOH and Li₂CO₃ were added to TiO₂ solutions prepared in water and ethanol media, respectively. The powders were subsequently dried and calcined at various temperatures. The phase and morphological transitions from TiO₂ to Li₄Ti₅O₁₂ were characterized using X-ray powder diffraction and transmission electron microscopy. The electrochemical performance of nanosized Li₄Ti₅O₁₂ was evaluated in detail by cyclic voltammetry and galvanostatic cycling. Furthermore, the high-rate performance and long-term cycle stability of Li₄Ti₅O₁₂ anodes for use in Li-ion batteries were discussed.     

Hydrothermal synthesis of MnO<Subscript>2</Subscript>/CNT nanocomposite with a CNT core/porous MnO<Subscript>2</Subscript> sheath hierarchy architecture for supercapacitors

MnO₂/carbon nanotube [CNT] nanocomposites with a CNT core/porous MnO₂ sheath hierarchy architecture are synthesized by a simple hydrothermal treatment. X-ray diffraction and Raman spectroscopy analyses reveal that birnessite-type MnO₂ is produced through the hydrothermal synthesis. Morphological characterization reveals that three-dimensional hierarchy architecture is built with a highly porous layer consisting of interconnected MnO₂ nanoflakes uniformly coated on the CNT surface. The nanocomposite with a composition of 72 wt.% (K_0.2MnO₂·0.33 H₂O)/28 wt.% CNT has a large specific surface area of 237.8 m²/g. Electrochemical properties of the CNT, the pure MnO₂, and the MnO₂/CNT nanocomposite electrodes are investigated by cyclic voltammetry and electrochemical impedance spectroscopy measurements. The MnO₂/CNT nanocomposite electrode exhibits much larger specific capacitance compared with both the CNT electrode and the pure MnO₂ electrode and significantly improves rate capability compared to the pure MnO₂ electrode. The superior supercapacitive performance of the MnO₂/CNT nancomposite electrode is due to its high specific surface area and unique hierarchy architecture which facilitate fast electron and ion transport.     

Improved electrochemical properties of Li(Ni<Subscript>0.7</Subscript>Co<Subscript>0.3</Subscript>)O<Subscript>2</Subscript> cathode for lithium ion batteries with controlled sintering conditions

Improved electrochemical properties of Li(Ni_0.7Co_0.3)O₂ cathode material are reported. Samples were synthesized by the co-precipitation method with various sintering conditions, namely temperature, time and atmosphere. Li(Ni_0.7Co_0.3)O₂ sintered at 850 °C for 14 h in air exhibited the lowest unit cell volume accompanied with relatively higher values of c/a and I ₁₀₃/I ₁₀₄ reflection peaks ratios. This also exhibited superior electrochemical properties, such as high charge–discharge capacity, high Coulombic efficiency, and low irreversible capacity loss. This can be attributed to improved hexagonal ordering, crystallinity and morphology. The electrochemical cell parameters were better than the reported ones, probably due to controlled sintering conditions.     

Synthesis,structural, and electrochemical performance of V<Subscript>2</Subscript>O<Subscript>5</Subscript> nanotubes as cathode material for lithium battery

Various vanadium oxide nanostructures are currently drawn interest for the potential applications of Li batteries, super capacitors, and electrochromic display devices. In this article, the synthesis of V₂O₅ nanotubes by hydrothermal method using 1-hexadecylamine (HDA) and PEO as a template and surface reactant were reported, respectively. The structural properties and electrochemical performances of these nanostructures were investigated for the application of Li batteries. Structure and morphology of the samples were investigated by XRD, FTIR, SEM, and TEM analysis. The battery with V₂O₅ nanotubes electrode showed initial specific capacity of 185 mAhg⁻¹, whereas the PEO surfactant V₂O₅ nanotubes exhibited 142 mAhg⁻¹. It was found that PEO surfactant V₂O₅ nanotubes material showed less specific capacity at initial stages but better stability was exhibited at higher cycle numbers when compared to that of V₂O₅ nanotubes. The cyclic performance of the PEO surfactant material seems to be improved with the role of polymeric component due to its surface reaction with V₂O₅ nanotubes during the hydrothermal process.     

Properties of LiNi<Subscript>0.8</Subscript>Co<Subscript>0.1</Subscript>Mn<Subscript>0.1</Subscript>O<Subscript>2</Subscript> as a high energy cathode material for lithium-ion batteries

Nickel-rich layered materials are prospective cathode materials for use in lithium-ion batteries due to their higher capacity and lower cost relative to LiCoO₂. In this work, spherical Ni_0.8Co_0.1Mn_0.1(OH)₂ precursors are successfully synthesized through a co-precipitation method. The synthetic conditions of the precursors - including the pH, stirring speed, molar ratio of NH₄OH to transition metals and reaction temperature - are investigated in detail, and their variations have significant effects on the morphology, microstructure and tap-density of the prepared Ni_0.8Co_0.1Mn_0.1 (OH)₂ precursors. LiNi_0.8Co_0.1Mn_0.1O₂ is then prepared from these precursors through a reaction with 5% excess LiOH· H₂O at various temperatures. The crystal structure, morphology and electrochemical properties of the Ni_0.8Co_0.1Mn_0.1 (OH)₂ precursors and LiNi_0.8Co_0.1Mn_0.1O₂ were investigated. In the voltage range from 3.0 to 4.3 V, LiNi_0.8Co_0.1Mn_0.1O₂ exhibits an initial discharge capacity of 193.0mAh g^-1 at a 0.1 C-rate. The cathode delivers an initial capacity of 170.4 mAh g^-1 at a 1 C-rate, and it retains 90.4% of its capacity after 100 cycles.     

A novel biosensor based on electro-co-deposition of sodium alginate-Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>-graphene composite on the carbon ionic liquid electrode for the direct electrochemistry and electrocatalysis of myoglobin

A novel biosensor based on electro-co-deposition of myoglobin (Mb), sodium alginate (SA), Fe₃O₄-graphene (Fe₃O₄-GR) composite on the carbon ionic liquid electrode (CILE) was fabricated using Nafion as the film forming material to improve the stability of protein immobilized on the electrode surface, and the modified electrode was abbreviated as Nafion/Mb-SA-Fe₃O₄-GR/CILE. FT-IR and UV–vis absorption spectra suggested that Mb could retain its native structure after being immobilized in the SA-Fe₃O₄-GR composite film. The electrochemical behavior of the modified electrode was studied by cyclic voltammetry, and a pair of symmetric redox peaks appeared in the cyclic voltammograms, indicating that direct electron transfer of Mb was realized on the modified electrode, which was ascribed to the good electrocatalytic capability of Fe₃O₄-GR composite, the good biocompatibility of SA and the synergistic effects of SA and Fe₃O₄-GR composite. The electrochemical parameters of the electron transfer number (n), the charge transfer coefficient (α) and the electron transfer rate constant (k _s) were calculated as 0.982, 0.357 and 0.234 s^?1, respectively. The modified electrode exhibited good electrocatalytic ability to the reduction of trichloroacetic acid (TCA) with wide linear range from 1.4 to 119.4 mmol/L, low detection limit as 0.174 mmol/L (3σ), good stability and reproducibility.     

Selective Hydrogenation of <Emphasis Type="Italic">trans</Emphasis>-Cinnamaldehyde over SiO<Subscript>2</Subscript>-Supported Co–Ir Bimetallic Catalysts

Selective hydrogenation of trans-cinnamaldehyde was studied on SiO₂-supported Co–Ir bimetallic catalysts. Addition of Ir to Co/SiO₂ increased the hydrogenation selectivity and activity of cinnamaldehyde to the corresponding cinnamyl alcohol (UOL). A selectivity as higher as 93% to UOL at ambient temperature under H₂ pressure of 2.0 MPa was obtained over catalyst with loadings of 10 wt% Co and 0.5 wt% Ir (Co_10.0Ir_0.5/SiO₂). The XRD, Raman and TPR results showed that the higher dispersed Co₃O₄ particles were formed on SiO₂ due to the addition of Ir, which increased the reducibility of Co₃O₄ to Co⁰. The reduction of oxidized Co–Ir/SiO₂ samples occurred at the temperatures with about 200 K lower than that of the one without Ir species as evidenced by the observations of TPR and in-situ Raman characterizations. The XPS results indicated that the large parts of Co₃O₄ in the sample of Co–Ir/SiO₂ were reduced to Co⁰, but only small parts of that were reduced to Co⁰ in the sample of Co/SiO₂ under flowing 5%H₂/Ar at 673 K. The CO chemisorptions revealed that the irreversible uptakes of CO on the reduced Co–Ir/SiO₂ sample was much higher than those on the reduced Co/SiO₂ and Ir/SiO₂, and also higher than the combination of that on the reduced Co/SiO₂ and Ir/SiO₂, respectively. The experimental data suggested that the presence of Ir played a key role in the reduction of Co₃O₄ to Co⁰ through a strong interaction between them and that the amount of Co⁰ at the catalyst surfaces was correlated to the activity and more importantly to the UOL selectivity.     

Partial oxidation of methane over Ni/Ce-Zro<Subscript>2</Subscript>/θ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

The catalytic behavior of Ni/Ce-ZrO₂/θ-Al₂O₃ has been investigated in the partial oxidation of methane (POM) toward synthesis gas. The catalyst showed high activity and selectivity due to the heat treatment of the support and the promotional effect of Ce-ZrO₂. It is suggested that the support was stabilized through the heat treatment of γ-Al₂O₃ and the precoating of Ce-ZrO₂, on which a protective layer was formed. Moreover, sintering of the catalyst was greatly suppressed for 24 h test. Pulse experiments of CH₄, O₂ and/or CH₄/O₂ with a molar ratio of 2 were systematically performed over fresh, partially reduced and well reduced catalyst. Results indicate that CH₄ can be partially oxidized to CO and H₂ by the reactive oxygen in complex NiO_x species existing over the fresh catalyst. It is demonstrated that POM over Ni/Ce-ZrO₂/θ-Al₂O₃ follows the pyrolysis mechanism, and both the carbonaceous materials from CH₄ decomposition over metallic nickel and the reactive oxygen species present on NiO_x and Ce-ZrO₂ are intermediates for POM.     

Effect of surface modification of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles on the preparation of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/polystyrene composite particles via miniemulsion polymerization

Fe₃O₄ nanoparticles were modified by n-octadecyltrimethoxysilane (C18TMS) and 3-trimethoxysilylpropylmethacrylate (MPS). The modified Fe₃O₄ nanoparticles were used to prepare Fe₃O₄/polystyrene composite particles by miniemulsion polymerization. The effect of surface modification of Fe₃O₄ on the preparation of Fe₃O₄/polystyrene composite particles was investigated by transmission electron microscopy, Fourier transform infrared spectrophotometer (FT-IR), contact angle, and vibrating sample magnetometer (VSM). It was found that C18TMS modified Fe₃O₄ nanoparticles with high hydrophobic property lead to the negative effect on the preparation of the Fe₃O₄/polystyrene composite particles. The obtained composite particles exhibited asymmetric phase-separated structure and wide size distribution. Furthermore, un-encapsulated Fe₃O₄ were found in composite particles solution. MPS modified Fe₃O₄ nanoparticles showed poor hydrophobic properties and resulted in the obtained Fe₃O₄/polystyrene composite particles with regular morphology and narrow size distribution because the ended C=C of MPS on the surface of Fe₃O₄ nanoparticles could copolymerize with styrene which weakened the phase separation distinctly.     

Characterization of Fischer–Tropsch Cobalt-Based Catalytic Systems (Co/SiO<Subscript>2</Subscript> and Co/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>) by X-ray Diffraction and Magnetic Measurements

Results of the characterization of six Co-based Fischer–Tropsch (FT) catalysts, with 15% Co loading and supported on SiO₂ and Al₂O₃, are presented. Room temperature X-ray diffraction (XRD), temperature and magnetic field (H) variation of the magnetization (M), and low-temperature (5 K) electron magnetic resonance (EMR) are used for determining the electronic states (Co⁰, CoO, Co₃O₄, Co²⁺) of cobalt. Performance of these catalysts for FT synthesis is tested at reaction temperature of 240 °C and pressure of 20 bars. Under these conditions, 15% Co/SiO₂ catalysts yield higher CO and syngas conversions with higher methane selectivity than 15% Co/Al₂O₃ catalysts. Conversely the Al₂O₃ supported catalysts gave much higher selectivity towards olefins than Co/SiO₂. These results yield the correlation that the presence of Co₃O₄ yield higher methane selectivity whereas the presence of Co²⁺ species yields lower methane selectivity but higher olefin selectivity. The activities and selectivities are found to be stable for 55 h on-stream.