Optimum design approach for low‐speed,high‐torque permanent magnet motors

This paper presents an optimum design approach for low‐speed, high‐torque permanent magnet motors. The approach is divided into two steps: the first consists of the rough estimation of torque by linear analysis, and the second the optimization of the motor configuration by nonlinear FEM analysis. Under restricted dimensional specifications and electrical requirements, a 16‐pole, 18‐coil permanent magnet motor with a rating of 600 Nm and 300 rpm was designed and constructed. © 2001 Scripta Technica, Electr Eng Jpn, 135(4): 52–63, 2001     

Design and analysis of low‐speed,high‐torque permanent magnet motors

This paper presents design and analysis of low‐speed, high‐torque permanent magnet motors. The motor has 16‐pole, 18‐coil construction, and a unique winding arrangement to produce high torque. The simplified torque analysis is proposed considering the line of magnetic induction distribution in the motor. The validity of the proposed analysis has been proved by both linear and nonlinear FEM analyses. The 500‐Nm, 200‐rpm test motor has been designed and constructed and the motor shows the expected characteristics. © 2000 Scripta Technica, Electr Eng Jpn, 132(3): 48–56, 2000     

A 5‐Gbps low‐power low‐jitter voltage‐mode transmitter with two‐tap pre‐emphasis and impedance calibration in 65‐nm CMOS

A low‐power low‐jitter voltage‐mode (VM) transmitter with two‐tap pre‐emphasis and impedance calibration for high‐speed serial links is presented. Based on a comprehensive analysis of the relationship between impedance, supply current, and pre‐emphasis of the output driver, an impedance control circuit (ICU) is presented to maintain the 50 Ω output impedance and suppress the reflection, a self‐biased regulator is proposed to regulate the power supply, and an edge driver is introduced to speed up the signal transition time. Therefore, the signal integrity (SI) of the transmitter is improved with low power consumption. The whole transmitter is implemented in 65‐nm CMOS technology. It provides an eye height greater than 688 mV at the far end with a root‐mean‐squared jitter of less than 6.99 ps at 5 Gbps. The transmitter consumes 15.2 mA and occupies only 370 μm × 230 μm. © 2016 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Design criterion for high‐speed low‐power SC circuits

The settling behavior of switched‐capacitor (SC) circuits is investigated in this paper. The analysis is performed for typical SC circuits employing two‐stage Miller‐compensated operational amplifiers (op‐amps). It aims to evaluate the real effectiveness of the conventional design approach for the optimization of op‐amp settling performances. It is demonstrated that the classical strategy is quite inaccurate in typical situations in which the load capacitance to be driven by the SC circuit is small. The presented study allows a new settling optimization strategy based on an advanced circuit model to be defined. As shown by design examples in a commercial 0.35‐ µm CMOS technology, the proposed approach guarantees a significant settling time reduction with respect to the existing settling optimization strategy, especially in the presence of small capacitive loads to be driven by the SC circuit. Copyright © 2010 John Wiley & Sons, Ltd.     

A framework for high‐speed parallel‐prefix adder performance evaluation and comparison

A new framework is proposed for the evaluation and comparison of high‐speed parallel‐prefix adders. The framework specifies input registers and latches and requires sum feedback for single cycle pipelined operation. Test pattern generation is also specified. A newly revised energy‐efficient 64‐bit carry select adder with distributed mixed valence logic to help reduce fan‐out and wire load is presented. Footless pulsed‐precharge domino and compound domino circuits, and smaller transistors help to reduce area and power. Detailed simulations with 65 nm CMOS models are compared with other parallel‐prefix adders that have been instantiated for comparison. Within this framework, energy reductions of 40% are obtained for the new adder versus two leading Kogge‐Stone designs, and 25% versus a new constant delay logic Sklansky style design, at similar cycle times. Copyright © 2014 John Wiley & Sons, Ltd.     

A subthreshold current‐sensing ΣΔ modulator for low‐voltage and low‐power sensor interfaces

A continuous‐time (CT) ΣΔ modulator for sensing and direct analog‐to‐digital conversion of nA‐range (subthreshold) currents is presented in this work. The presented modulator uses a subthreshold technique based on subthreshold source‐coupled logic cells to efficiently convert subthreshold current to digital code without performing current‐to‐voltage conversion. As a benefit of this technique, the current‐sensing CT ΣΔ modulator operates at low voltage and consumes very low power, which makes it convenient for low‐power and low‐voltage current‐mode sensor interfaces. The prototype design is implemented in a 0.18 µm standard complementary metal‐oxide semiconductor technology. The modulator operates with a supply voltage of 0.8 V and consumes 5.43 μW of power at the maximum bandwidth of 20 kHz. The obtainable current‐sensing resolution ranges from effective number of bits (ENOB) = 7.1 bits at a 5 kHz bandwidth to ENOB = 6.5 bits at a 20 kHz bandwidth (ENOB). The obtained power efficiency (peak FoM = 1.5 pJ/conv) outperforms existing current‐mode analog‐to‐digital converter designs and is comparable with the voltage‐mode CT ΣΔ modulators. The modulator generates very low levels of switching noise thanks to CT operation and subthreshold current‐mode circuits that draw a constant subthreshold current from the voltage supply. The presented modulator is used as a readout interface for sensors with current‐mode output in ultra low‐power conditions and is also suitable to perform on‐chip current measurements in power management circuits. Copyright © 2014 John Wiley & Sons, Ltd.     

A low‐power technique for high‐resolution dynamic comparators

A low‐power technique for high‐resolution comparators is introduced. In this technique, p‐type metal‐oxide‐semiconductor field‐effect transistors are employed as the input of the latch of the comparator just like the input of the preamplifier. The latch and preamplifier stages are activated in a special pattern using an inverter‐based controller. Unlike the conventional comparator, the preamplification delay can be set to an optimum low value even if after the preamplification, the output voltages is less than n‐channel metal‐oxide semiconductor voltage threshold. As a result, the proposed comparator reduces the power consumption significantly and enhances the speed. The speed and power benefits of the proposed comparator were verified using analytical derivations, PVT corners, and post layout simulations. The results confirm that the introduced technique reduces the power consumption by 60%, also, provides 57% better comparison speed for an input common mode voltage (V_cm) range of 0‐Vdd/2.     

A speed control method for a PM motor using a speed observer and a low‐resolution encoder

This paper proposes a new speed control method for a PM motor using a low‐resolution encoder and a speed observer. The servo system should be economical and simple. For this purpose, this paper realizes the high‐performance speed control system using a low‐resolution encoder, whose performance is nearly equal to the performance of speed servo system using a conventional optical encoder. The speed observer uses the information of motor current and motor voltage. The rotor position is calculated by the estimated value of speed observer. This observer has the influence of electrical parameter variation. This paper proposes the correction algorithm of both the voltage error of PWM inverter and the electrical parameter variation. The experimental results and numerical simulation results point out that the proposed speed control system has the desired speed response with respect to parameter variations and load torque perturbation. © 2003 Wiley Periodicals, Inc. Electr Eng Jpn, 143(1): 66–75, 2003; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10121     

Design of high‐speed low‐power parallel‐prefix adder trees in nanometer technologies

This paper presents a novel approach to design high‐speed low‐power parallel‐prefix adder trees. Sub‐circuits typically used in the design of parallel‐prefix trees are deeply analyzed and separately optimized. The modules used for computing the group propagate and generate signals have been designed to improve their energy‐delay behavior in an original way. When the ST 45 nm 1 V CMOS technology is used, in comparison with conventional implementations, the proposed approach exhibits computational delay with mean value and standard deviation up to 40% and 48% lower and achieves energy consumption with mean value and standard deviation up to 57% and 40% lower. A 32‐bit Brent‐Kung tree made as proposed here reaches a computational delay lower than 165 ps and dissipates 147.4fJ on average. Copyright © 2013 John Wiley & Sons, Ltd.     

Examination of new vector control system of permanent magnet synchronous motor for high‐speed drives

A new vector control system for permanent magnet synchronous motor drives has been developed. To stabilize the current control loop in the high‐rotating‐speed region, a novel configuration of current controller is introduced. The unique characteristic of the proposed current controller is that the current regulator is connected to the conventional motor model in a series. By analyzing the transfer characteristics of the control, it became clear that the influence of the coupling component between the d–q axes can be deleted theoretically if the control parameters are set properly. The stability and torque response of the proposed vector control system were improved, and the effectiveness of the proposed controller was demonstrated by a time domain simulation and some experiments. In addition, the robustness of the controlling system was investigated experimentally. © 2011 Wiley Periodicals, Inc. Electr Eng Jpn, 176(4): 61–72, 2011; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21123     

DC–3 GHz low‐noise,flat‐gain‐response,and high‐linearity amplifier

This paper describes the design, fabrication, and testing of a DC–3 GHz ultra‐wideband low‐noise amplifier (LNA) using Avago ATF‐54143 enhanced‐mode pseudomorphic high‐electron mobility transistor. Negative feedback network is introduced to ensure unconditional stability of the LNA over the full waveband. Simulation results show that the LNA provides a gain varying between 14.872 and 14.052 dB, a noise figure (NF) of less than 2.2 dB, and voltage standing wave ratios (VSWRs) approaching 2. A high simulated output third‐order intercept point (OIP₃) of >30.2 dBm is achieved. In contrast, in 1‐dB bandwidth of DC–3 GHz, the measured gain is nominal at 13.10 dB. The obtained NF changes in a small range of 2–2.178 dB, and the measured VSWRs are no more than 1.64, which are better than obtained from simulation results. At the same time, OIP₃ at 1, 2, and 3 GHz is 30.3, 29.13, and 29.34 dBm, respectively, while the output at the 1‐dB compression point (P _1dB ) is 15.43, 14.83, and 14.33 dBm, respectively. © 2016 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Proposal of current control method of high‐speed AC motor system

In this paper, a current control method for a high‐speed AC motor system is proposed. In high‐speed driving operation, the current controller tends to lose stability because of the dead time caused by computational delay and electromagnetic coupling included in the AC motor model. The main purpose of the proposed method is reduction of the dead time on the current controller. The proposed method is based on model predictive control and optimization of the start timing. The effectiveness of the proposed method is confirmed by simulation results. © 2011 Wiley Periodicals, Inc. Electr Eng Jpn, 176(1): 37–45, 2011; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21083     

Low‐power,low‐area preamplifier for ultra high‐speed multi‐channel optical communication system

A novel circuit technique was applied to the design of a preamplifier for ultra high‐speed short‐distance parallel optical communication system in standard 180‐nm CMOS technology. This circuit is featured by low power, low area as well as high gain bandwidth product, and suited for applications in low‐cost process. The restraint on voltage headroom as bottleneck in traditionally adopted regulated cascode configuration has been fundamentally analyzed and lifted by feed‐forward common gate stage to achieve high gain bandwidth product under limited f_T and strict power restriction. Complex poles were carefully assigned to further attain bandwidth extension without sacrifice on power, noise, and chip area. No additional peaking techniques and subsequent gain‐boosting stages are adopted, which makes the design simple and favorable in low‐cost high‐density multi‐channel optical communication system. The preamplifier provides a trans‐impedance gain of up to 52 dBΩ and a 3‐dB bandwidth of 8.4 GHz. Operating under a 1.8‐V supply, the power dissipation is 8 mW, and the chip area is only 0.075×0.08 mm. The measured average input‐referred noise–current spectral density is . Copyright © 2011 John Wiley & Sons, Ltd.     

Current‐mode dual‐output ICCII‐based tunable universal biquadratic filter with low‐input and high‐output impedances

A new tunable current‐mode (CM) biquadratic filter with three inputs and three outputs using three dual‐output inverting second‐generation current conveyors, three grounded resistors and two grounded capacitors is proposed. The proposed circuit exhibits low‐input impedance and high‐output impedance which is important for easy cascading in the CM operations. It can realize lowpass, bandpass, highpass, bandreject and allpass biquadratic filtering responses from the same topology. The circuit permits orthogonal controllability of the quality factor Q and resonance angular frequency ω_o, and no component matching conditions or inverting‐type input current signals are imposed. All the passive and active sensitivities are low. Hspice simulation results are based on using TSMC 0.18 µm 1P6M process complementary metal oxide semiconductor technology and supply voltages ±0.9 V to verify the theoretical analysis. Copyright © 2012 John Wiley & Sons, Ltd.     

A novel low‐power receiver topology for RF and microwave applications

A novel low‐power receiver topology for radio‐frequency and microwave applications is presented. The proposed solution exploits a simple connection between the low‐noise amplifier and the subsequent mixer, which is realized by means of a high‐value resistor and a current mirror, achieving low noise and high linearity performance with an extremely low power consumption. The criteria for its optimal design are derived in order to accomplish the main trade‐offs among noise figure (NF), linearity, and current consumption performance. As a case of study, the new topology has been designed in the case of I/Q direct conversion receiver for IEEE 802.15.4 standard (ZigBee) applications at 2.45 GHz. The receiver exhibits a NF of 8.7 dB, 50Ω input impedance, a voltage gain of 26 dB, an input‐referred third‐order intercept point of ?13 dBm, and a power consumption of 8.6 mW, which represent one of the best performance trade‐offs obtained in the literature. Copyright © 2008 John Wiley & Sons, Ltd.     

An MTJ‐based non‐volatile flip‐flop for high‐performance SoC

The conventional magnetic tunneling junction (MTJ)‐based non‐volatile D flip‐flop (NVDFF) has a slow D‐Q delay and a tradeoff between its D‐Q delay and its sensing current. In addition, a sufficient write current cannot be obtained with the core device, since two MTJs exist in the write path and a write current degradation problem occurs due to the precharge transistors. The proposed MTJ‐based non‐volatile semidynamic flip‐flop (NVSDFF) has a semidynamic structure that ensures a fast D‐Q delay and separates the sensing circuit from the D‐Q signal path to reduce the sensing current without affecting the D‐Q delay. The proposed NVSDFF also provides a sufficient write current by merely using the core device, since only one MTJ exists in the write path. In addition, the head switch, which is added to remove the write current degradation problem, further reduces the sensing current. Thus, the proposed NVSDFF has a higher read disturbance margin than the previous NVDFF with an IO device. The HSPICE simulation results with the industry‐compatible 45 nm model parameter show that the D‐Q delay in the proposed NVSDFF is 50.5% of that of the previous NVDFF with an IO device, and the sensing current, 32.3%. In the proposed NVSDFF, the read disturbance margin is 15.9% larger than in the previous NVDFF with an IO device, and the area is 17.8% smaller. Copyright © 2012 John Wiley & Sons, Ltd.     

Control schemes and transient characteristics of a high‐speed phase shifter for power flow control in power transmission systems

In recent years, attention has been paid to the concept of FACTS (Flexible AC Transmission Systems), along with significant progress in power electronic technology. A high‐speed phase shifter, which is one of the most promising devices in the FACTS concept, has the potential of power flow control and/or voltage stability in power transmission systems. In this paper, theory and experiment reveal that conventional high‐speed phase shifters may cause power swings in a transient state as a result of coupling between instantaneous active and reactive power control loops. Thus, two new control schemes for a high‐speed phase shifter are proposed to achieve both power flow control and power swing damping. The second proposed control scheme is based on the control scheme of an already proposed series active filter. Simulated and experimental results agree well with analytical results, not only in steady states but also in transient states. © 1999 Scripta Technica, Electr Eng Jpn, 128(2): 74–82, 1999     

Visualization of high‐speed phenomena using an acousto‐optic laser deflector

An acousto‐optic laser deflector was used for visualization of high‐speed phenomena, such as shock waves and density perturbations accompanying an impulse discharge, or shock waves generated by laser‐induced breakdown in air. Using a continuous wave laser as the light source, shadowgraphs of shock waves and density perturbations were obtained at shutter speeds down to 1µs. Results showed that shock waves propagated at a speed of 417 m/s in the case of an impulse discharge, and 485 m/s in the case of laser‐induced breakdown. Prebreakdown phenomena such as leaders progressing from the high‐voltage electrode were also visualized. Compared to conventional high‐speed imaging techniques, this method is useful when using a laser light source, since the acousto‐optic crystal can accommodate high‐intensity laser light. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 154(3): 9–15, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20279     

A 5‐Gbps USB3.0 transmitter and receiver linear equalizer

A USB3.0 compatible transmitter and the linear equalizer of the corresponding receiver are presented in this paper. The architecture and circuit design techniques used to meet the strict requirements of the overall link design are explored. Output voltage amplitude and de‐emphasis levels are programmable, whereas the output impedance is calibrated to 50Ω. A programmable receiver equalizer is also presented with its main purpose being to compensate for the channel losses; this is employed together with a DC offset compensation scheme. The 6.25‐GHz equalizer provides a 10 dB overall gain equalization and 5.5‐dB peaking at the maximum gain setting. Designed using a mature and well established 65 nm complementary metal oxide semiconductor process, the layout area is 400 µm × 210 µm for the transmitter core, and 140 µm × 70 µm for the equalizer core. The power consumption is 55 and 4 mW, respectively, from a 1.2 V supply at a data rate of 5 Gbps. The target application for such high‐speed blocks is to implement the critical part of the physical layer that defines the signaling technology of SuperSpeed USB3 PHY. However, identical iterations of the circuitry discussed can be used for similar high‐speed applications like the PCI express (PCIe). Copyright © 2014 John Wiley & Sons, Ltd.     

Low‐voltage low‐power CMOS receiver front‐end for gigabit short‐reach optical communications

This article presents a new CMOS receiver analog front‐end for short‐reach high‐speed optical communications, which compensates the limited product bandwidth length of 1‐mm step‐index plastic optical fiber (SI‐POF) channels (45 MHz · 100 m) and the required large‐diameter high‐capacitance Si PIN photodetector (0.8 mm–3 pF). The proposed architecture, formed by a transimpedance amplifier and a continuous‐time equalizer, has been designed in a standard 0.18‐µm CMOS process with a single supply voltage of only 1 V, targeting gigabit transmission for simple no‐return‐to‐zero modulation consuming less than 23 mW. Experimental results validate the approach for cost‐effective gigabit SI‐POF transmission. Comparative analysis with previously reported POF receivers has been carried out by introducing a useful figure of merit. Copyright © 2012 John Wiley & Sons, Ltd.