Adsorption behavior of reactive dyes from aqueous solutions on chitosan

The capability of the use of chitosan for removing vinyl sulfone and chlorotriazine reactive dyes from aqueous solutions was examined, including equilibrium and dynamic studies. Experiments were performed as a function of dye concentration, and the amount and particle size of chitosan. It was shown that the adsorption capacities of chitosan were comparatively high for the three investigated dyes. The equilibrium data could be best fitted by the Redlich–Peterson equation over the entire concentration range (50–500 g m⁻³). A comparison of the adsorption capacity among such adsorbents as chitin and powdered activated carbon was made. Two rate parameters were finally obtained to describe the adsorption process on a quantitative basis. These parameters could be well correlated to the amount and particle size of dry chitosan. ©1997 SCI     

Biosorption of methylene blue from aqueous solution by softstem bulrush (Scirpus tabernaemontani Gmel.)

BACKGROUND: The removal of methylene blue from aqueous solution was studied using softstem bulrush (Scirpus tabernaemontani Gmel.) as the biosorbent. The effects of various parameters including contact time, biosorbent dosage, ionic strength and solution pH on the biosorption were investigated. RESULTS: The sorption capacity increased with an increase in biosorbent dosage and a decrease in ionic strength. The equilibrium time was found to be 240 min for full equilibration. Pseudo‐first‐order, pseudo‐second‐order, Bangham equation and intraparticle diffusion models were applied to fit the kinetic data, and the results showed that the sorption process followed the pseudo‐second‐order model. Equilibrium data conformed to Langmuir and Redlich–Peterson isotherm models, with a maximum monolayer biosorption capacity of 53.8 mg g^?1 for the Langmuir isotherm at 18 °C. The value of ΔG was estimated to be ? 29.24 kJ mol^?1, indicating the spontaneous nature of the biosorption. The biosorption process was strongly pH‐dependent and favourable at alkaline pH. CONCLUSION: Softstem bulrush, which is readily available and inexpensive, could be employed as a promising biosorbent for the removal of dye. Copyright © 2008 Society of Chemical Industry     

Removal of nickel from aqueous solutions by citric acid modified Ceiba pentandra hulls: Equilibrium and kinetic studies

The removal of Ni(II) from aqueous solutions using biomass prepared from Ceiba pentandra hulls powder modified with citric acid treatment (CAMCPH) has been studied by batch method. The biosorbent was characterised before and after citric acid modification using SEM, FT‐IR and XRD. Experimental parameters that influence the biosorption of Ni(II), such as pH, biosorbent dose, contact time and initial concentration of metal ion have been investigated. The adsorption of Ni(II) increased with increase in contact time and reached equilibrium within 50 min. The maximum removal of Ni(II) was observed at pH 5.0. The kinetic data were analysed using three adsorption kinetic models: the pseudo‐first, second‐order kinetics and intra‐particle diffusion. The results showed that the pseudo‐second‐order model fits the experimental data very well. The equilibrium data were analysed using Langmuir, Freundlich and Dubinin–Radushkevich isotherm models. Langmuir model provided the best correlation for the adsorption of Ni(II) by CAMCPH and the monolayer biosorption capacity for Ni(II) removal was 34.34 mg/g. Desorption experiments were carried out using HCl solution and the recovery of the metal ion from CAMCPH was found 98%. Desorption experiments showed the feasibility of regeneration of the biosorbent for further use after treating with dilute HCl. © 2011 Canadian Society for Chemical Engineering     

Modelling of adsorption of textile dyes over multi-walled carbon nanotubes: Equilibrium and kinetic

The paper deals with the application of multiwall carbon nanotubes (CNTs) to the adsorption of dyes from wastewater. Textile dyes are dangerous and diffused pollutant in wastewater, and the paper results confirmed the good adsorption ability of CNTs, with respect to classic active carbon, even for different dye types. The effect of surface treatments of CNTs was primarily investigated, revealing that neither the presence of residual catalyst nor common surface treatment (oxidation) affects the CNT's performances. Therefore less expensive nonpurified CNTs were assessed as good and economically convenient alternative for the process. In order to gain in generality in adsorption kinetic modelling, the parameters of the "best fitting" pseudo-second order model have been correlated to the main process variables (the dye initial concentration and the specific mass of CNTs.) setting-up a predictive kinetic model useful design new application of these materials in currently operating industrial operations for adsorption. In addition, isothermal data were used to screen all the relevant adsorption isotherms models and the Temkin model was confirmed as the more effective to accurately fit equilibrium data for any of the considered different dye types.     

Removal of Anionic Dyes from Water using Citrus limonum (Lemon) Peel: Equilibrium Studies and Kinetic Modeling

Abstract

The present study was undertaken to evaluate the adsorption potential of Citrus limonum (lemon) peel as an adsorbent for the removal of two anionic dyes, Methyl orange (MO) and Congo red (CR) from aqueous solutions. The adsorption was studied as a function of contact time, initial concentration, and temperature by batch method. The adsorption capacities of lemon peel adsorbent for dyes were found 50.3 and 34.5 mg/g for MO and CR, respectively. The equilibrium adsorption data was well described by the Langmuir model. Three simplified kinetic models viz. pseudo-first-order, pseudo-second-order, and Weber and Morris intraparticle diffusion model were tested to describe the adsorption process. Kinetic parameters, rate constants, equilibrium sorption capacities, and related correlation coefficients for each kinetic model were determined. It was found that the present system of dyes adsorption on lemon peel adsorbent could be described more favorably by the pseudo-first-order kinetic model. The results of the present study reveal that lemon peel adsorbent can be fruitfully utilized as an inexpensive adsorbent for dyes removal from effluents.     

Comparative removal of two textile dyes from aqueous solution by adsorption onto marine-source waste shell: Kinetic and isotherm studies

Scallop shell was used as a low-cost adsorbent for removal of two anionic textile dyes, Reactive Blue 19 (RB19) and Acid Cyanine 5 R (AC5R), from aqueous solutions. The adsorbent was characterized using inductively coupled plasma optical emission spectrometry (ICP-OES), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR) and scanning electron microscopy (SEM). The dye removal efficiency of scallop shell was determined as function of contact time, solution pH, initial dye concentration and adsorbent dosage. With increasing dye concentration, the adsorption of both dyes decreased, while it increased with increasing adsorbent dosage. Optimum removal of RB19 and AC5R was achieved at pH=6. Adsorption equilibrium data were well described by the Freundlich model. The maximum dye adsorption capacity of scallop shell as estimated from the Langmuir isotherm was 12.36 and 12.47 mg/g for RB19 and AC5R, respectively. The adsorption kinetic data showed excellent correlation with the pseudosecond-order model. It was concluded that scallop shell has a remarkable potential for the sorption of RB19 and AC5R and can be used for treatment of the dye contaminated wastewater.     

Removal of basic dyes from aqueous solution by low-cost adsorbent: Wood apple shell (Feronia acidissima)

The adsorption of two basic dyes, methylene blue (MB) and crystal violet (CV) on wood apple shell (WAS) were investigated using a batch adsorption technique. A series of experiments were undertaken in an agitated batch adsorber to assess the effect of the system variables such as solution pH, dye concentration and temperature. Removal of dyes was observed to be most effective at higher pH. Freundlich and Langmuir isotherm models were applied to the equilibrium data. The results showed that Langmuir equation fits better than the Freundlich equation. It was observed that the WAS adsorbent showed higher adsorption capacity for crystal violet (130 mg/g) than methylene blue (95.2 mg/g). The FTIR studies indicate that the interaction of dye and WAS surface is via the nitrogen atoms of the adsorbate and oxygen groups of the adsorbent. The adsorption of dyes onto WAS proceeds according to a pseudo-second-order model. Thermodynamic parameters such as free energy (ΔG°), enthalpy (ΔH°) and entropy (ΔS°) were also calculated. The studies show that WAS, a lignocellulosic inexpensive material, can be an alternative to other expensive adsorbents used for dye removal in wastewater treatment.     

Removal Of methylene blue dye from simulated wastewater by alginic acid fiber as adsorbent: Equilibrium,kinetic, and thermodynamic studies

Alginic acid fiber was used as a novel adsorbent to remove methylene blue from aqueous solution, and adsorption mechanisms were investigated. System variables, including contact time, pH, temperature, and initial concentration were examined to investigate the effect on adsorption in batch experiments. The results showed that equilibrium reached in less than 20 min and pH significantly influenced the equilibrium value. Langmuir, Freundlich, and Temkin isotherm models were employed to analyse the isotherm behaviours. It was found the isotherm behaviours conform to Freundlich and Temkin models well, indicating a chemisorption process. Pseudo‐first‐order, pseudo‐second‐order, and intraparticle diffusion models were employed to investigate kinetic behaviours. The kinetic behaviour is best described by pseudo‐second‐order model. Thermodynamic parameters indicate that the process is spontaneous and exothermic.     

Chitin as biosorbent for phenol removal from aqueous solution: Equilibrium,kinetic and thermodynamic studies

Phenol removal from aqueous solution was studied employing chitin as low cost biosorbent. Initial biosorption tests carried out in the pH range 2–10 pointed out an optimum pH of 2. Temperature and initial phenol concentration were then varied in the ranges 15 ≤ T ≤ 50 °C and 10.4 ≤ C₀ ≤ 90.8 mg L⁻¹, respectively. The good applicability of Langmuir, Freundlich and Temkin models (R² = 0.990–0.993) to describe equilibrium isotherms suggested an intermediate mono-/multilayer biosorption mechanism along with a semi-homogeneous architecture of biosorbent surface. Biosorption capacity progressively increased from 3.56 to 12.7 mg g⁻¹ when starting phenol concentration was raised from 10.4 to 90.8 mg L⁻¹, and the related sorption kinetics was investigated by pseudo first-order, pseudo second-order and intraparticle diffusion models. The pseudo second-order model, which showed the best fit of experimental data (R² = 0.999), allowed estimating a second-order rate constant of 0.151 g mg⁻¹ h⁻¹ and a theoretical sorption capacity of 7.63 mg g⁻¹. Phenol biosorption capacity increased with temperature up to a maximum value, beyond which it decreased, suggesting the occurrence of a thermoinactivation equilibrium. Finally, to identify the main functional groups involved in phenol biosorption, both raw and phenol-bound materials were explored by FT-IR spectroscopy.     

Removal of direct Red‐31 and direct Orange‐26 by low cost rice husk: Influence of immobilisation and pretreatments

The aim of the present study is to investigate the influence of free, carboxymethyl cellulose (CMC) immobilised, PVA–alginate immobilised, and HCl treated rice husk on the removal of Direct Red‐31 and Direct Orange‐26 dyes. The biosorption capacity of the rice husk increased with HCl treatment (67.39 and 45.34 mg/g) and decreased with PVA–alginate immobilisation (9.73 and 10.03 mg/g) as compared to the free biomass (65.56 and 45.58 mg/g) at 200 mg/L dye concentration for Direct Red‐31 and Direct Orange‐26, respectively. Equilibrium data were best described by Langmuir Type 1 for Direct Red‐31 and Direct Orange‐26 (free, CMC immobilised, PVA–alginate immobilised, and HCl treated). Best correlation coefficients for Direct Red‐31 and Direct Orange‐26 using free, CMC immobilised, PVA–alginate immobilised, and HCl treated rice husk were obtained for pseudo‐second order and Elovich kinetic models. Values of Gibbs free energy (ΔG°) and enthalpy change (ΔH°) indicated that reaction was spontaneous and endothermic in nature at the studied temperatures. FT‐IR studies showed the involvement of carbonyl, carboxyl, and amide groups in the biosorption process. SEM exhibited the morphological changes on the biosorbent surface and BET analysis to determine the surface area is also carried out.     

Removal of basic and acid dyes from aqueous solutions by a waste containing boron impurity

In this study, batch experiments were carried out for the sorption of basic blue 41 (BB 41), and acid blue 225 (AB 225) onto boron waste (BW) from boron enrichment plant. The operating variables studied are the initial dye concentration, contact time, solution pH, and adsorbent dosage. The experimental equilibrium data were analyzed by using various adsorption isotherm models and the results have shown that the adsorption behavior of AB 225 and BB 41 could be described well reasonably by Langmuir and Temkin isotherms, respectively. Kinetics studies indicated that the adsorption of both dyes follow pseudo-second-order kinetics. The sorption of basic dye increased at high pH values, whereas the opposite was true for acidic dye. The results indicate that BW could be employed as low-cost alternatives to the commercially available adsorbents in wastewater treatment for the removal of acid and basic dyes.     

Removal of reactive dyes from wastewater by acrylate polymer beads bearing amino groups: isotherm and kinetic studies

The aim of this study was to prepare a novel resin for the removal of reactive dyes from aqueous media. To prepare the resin, poly(2‐hydroxyethyl methacrylate/ethylene glycol dimethacrylate) beads were grafted with poly(glycidyl methacrylate) by surface‐initiated atom transfer radical polymerisation. Epoxy groups of the grafted polymer were modified with tris(2‐aminoethyl)amine ligand. The modified resin was characterised by swelling studies, FT‐IR and SEM. Three different reactive dyes were selected (CI Reactive Brown 10, CI Reactive Red 120 and CI Reactive Green 5) and used in the removal studies. The effects of pH, temperature, ionic strength and initial dye concentration on the adsorption capacity of the resin were investigated. The adsorption capacity of the resin for Reactive Brown 10, Reactive Red 120 and Reactive Green 5 was 0.029 ± 0.010, 0.032 ± 0.0019 and 0.042 ± 0.0013 mmol/g resin (34.1 ± 1.2, 47.6 ± 2.3 and 69.3 ± 1.7 mg/g resin) respectively. The equilibrium adsorption data were analysed by Langmuir, Dubinin–Radushkevich, Freundlich and Temkin isotherm models. A good fit was found between the Langmuir isotherm and data for the three dyes on resin. The adsorption kinetic data were modelled using pseudo‐first‐order, pseudo‐second‐order and intraparticle diffusion kinetic equations. It was found that the pseudo‐second‐order equation could describe the adsorption kinetics. The results indicated that the modified resin is an attractive alternative for removing reactive dyes from wastewater.     

Removal of methylene blue dye from aqueous solutions by a new chitosan/zeolite composite from shrimp waste: Kinetic and equilibrium study

The adsorption of methylene blue dye (MBD) from aqueous solutions was investigated using a new composite made up of shrimp waste chitosan and zeolite as adsorbent. Response surface methodology (RSM) was used to optimize the effects of process variables, such as contact time, pH, adsorbent dose and initial MBD concentration on dye removal. The results showed that optimum conditions for removal of MBD were adsorbent dose of 2.5 g/L and pH of 9.0, and initial MBD concentration of 43.75 mg/L and contact time of 138.65 min. The initial concentration of dye had the greatest influence on MBD adsorption among other variables. The experimental data were well fitted by the pseudo-second order kinetic model, while the Freundlich isotherm model indicated a good ability for describing equilibrium data. According to this isotherm model, maximum adsorption capacity of the composite was 24.5 mg/g. Desorption studies showed that the desorption process is favored at low pH under acidic conditions.     

Removal of Lead Ions from Aqueous Solutions by Different Types of Industrial Waste Materials: Equilibrium and Kinetic Studies

Abstract

A comparative study of the adsorbents prepared from several industrial wastes for the removal of Pb²⁺ has been carried out. Fertilizer industry waste viz. carbon slurry and steel plant wastes viz. blast furnace (B.F.) slag, dust, and sludge were investigated as low‐cost adsorbents after proper treatment in the present study. The adsorption of Pb²⁺ on different adsorbents has been found in the order: B.F. sludge>B.F. dust>B.F. slag>carbonaceous adsorbent. The least adsorption of Pb²⁺ on carbonaceous adsorbent even having high porosity and consequently greater surface area as compared to other three adsorbents, indicates that surface area and porosity are not important factors for Pb²⁺ removal from aqueous solutions. The adsorption of Pb²⁺ has been studied as a function of contact time, concentration, and temperature. The adsorption has been found to be exothermic, and the data conform to the Langmuir equation. The kinetic results reveal that the present adsorption system follows Lagergren's first order rate equation. Since all three waste products from the steel industry show higher potential to remove lead from water, therefore, it is suggested that these metallurgical wastes can be fruitfully employed as low‐cost adsorbents for effluent treatment containing toxic metal ions.     

Removal of acid blue 113 and reactive black 5 dye from aqueous solutions by activated red mud

Removal of acid blue 113 (AB113) and reactive black 5 (RB5) dyes from aqueous solutions by activated red mud was investigated at different reaction parameters. Activated red mud has higher removal efficiency for AB113 than that for RB5. This can be explained by a greater molecular size of RB5 than that of AB113 and by different binding affinity with the surface of the activated red mud. Equilibrium data was fitted well with Freundlich isotherm and the kinetic data followed a pseudo second-order model. Maximum adsorption capacity was 83.33 mg/g and 35.58 mg/g at pH 3 for AB113 and RB5, respectively.