Mechanical and viscoelastic properties of soybean oil thermoset reinforced with jute fabrics and carded lyocell fiber

Composites and hybrid composites were manufactured from renewable materials based on jute fibers, regenerated cellulose fibers (Lyocell), and thermosetting polymer from soybean oil. Three different types of jute fabrics with biaxial weave architecture but different surface weights, and carded Lyocell fiber were used as reinforcements. Hybrid composites were also manufactured by combining the jute reinforcements with the Lyocell. The Lyocell composite was found to have better mechanical properties than other composites. It has tensile strength and modulus of about 144 MPa and 18 GPa, respectively. The jute composites also have relatively good mechanical properties, as their tensile strengths and moduli were found to be between 65 and 84 MPa, and between 14 and 19 GPa, respectively. The Lyocell‐reinforced composite showed the highest flexural strength and modulus, of about 217 MPa and 13 GPa, respectively. In all cases, the hybrid composites in this study showed improved mechanical properties but lower storage modulus. The Lyocell fiber gave the highest impact strength of about 35 kJ/m², which could be a result of its morphology. Dynamic mechanical analysis showed that the Lyocell reinforced composite has the best viscoelastic properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Development and application of triglyceride-based polymers and composites

Triglyceride oils derived from plants have been used to synthesize several different monomers for use in structural applications. These monomers have been found to form polymers with a wide range of physical properties. They exhibit tensile moduli in the 1–2 GPa range and glass transition temperatures in the range 70–120 °C, depending on the particular monomer and the resin composition. Composite materials were manufactured utilizing these resins and produced a variety of durable and strong materials. At low glass fiber content (35 wt %), composites produced from acrylated epoxidized soybean oil by resin transfer molding displayed a tensile modulus of 5.2 GPa, a flexural modulus of 9 GPa, a tensile strength of 129 MPa, and flexural strength of 206 MPa. At higher fiber contents (50 wt %) composites produced from acrylated epoxidized soybean oil displayed tensile and compression moduli of 24.8 GPa each, and tensile and compressive strengths of 463.2 and 302.6 MPa, respectively. In addition to glass fibers, natural fibers such as flax and hemp were used. Hemp composites of 20% fiber content displayed a tensile strength of 35 MPa and a tensile modulus of 4.4 GPa. The flexural modulus was ∼2.6 GPa and the flexural strength was in the range 35.7–51.3 MPa, depending on the test conditions. The flax composite materials had tensile and flexural strengths in the ranges 20–30 and 45–65 MPa, respectively. The properties exhibited by both the natural- and synthetic fiber-reinforced composites can be combined through the production of “hybrid” composites. These materials combine the low cost of natural fibers with the high performance of synthetic fibers. Their properties lie between those displayed by the all-glass and all-natural composites. Characterization of the polymer properties also presents opportunities for improvement through genetic engineering technology. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 703–723, 2001     

三维正交机织铜丝／玻璃纤维层间混杂复合材料的拉伸和弯曲性能研究

本文设计和制作了两种层间混杂结构的三维正交机织铜丝／玻璃纤维复合材料,分别为铜丝单面混杂和双面混杂复合材料。两种复合材料的拉伸性能和弯曲性能测试结果表明,单面铜丝／玻璃纤维混杂复合材料的归一化拉伸强度和模量分别为1214MPa和83GPa;高于双面铜丝／玻纤混杂复合材料44％和51％。单面铜丝／玻璃纤维混杂复合材料的归一化弯曲强度为964NPa,高于双面铜丝／玻纤复合材料27％。两者的弯曲模量比较接近,均为60GPa左右。由于铜丝的混杂效应,三维正交机织铜丝／玻璃纤维层间混杂复合材料的拉伸和弯曲性能与相同结构的玻璃纤维复合材料相比有一定的下降。     

碳玻混编单向复合材料的性能分析

采用碳纤维质量含量分别为7.4%、10.7%、13.8%的三种碳玻层间混编单向织物制备了纤维增强环氧树脂复合材料,分析了该类材料的力学性能与工艺性能。结果表明:碳玻层间混编复合材料的0°拉伸模量和0°压缩模量均随碳纤维含量的提高而升高,掺入碳纤维后碳玻混杂复合材料的0°拉伸强度比纯玻纤复合材料的有所降低,但随碳纤维含量的增加而升高,碳玻层间混编复合材料的0°压缩强度则没有明显的变化规律;掺入碳纤维后,碳玻层间混编复合材料的90°拉伸强度和模量均有所下降;低碳纤维含量的碳玻层间混编单向织物具有良好的Z向渗透性能。该类新材料未来有望在风电叶片结构减重和成本优化上发挥重要作用。     

Nonwoven polylactic acid and flax biocomposites

Flax fiber‐reinforced polylactic acid (PLA) biocomposites were made using a new technique incorporating an air‐laying nonwoven process. Flax and PLA fibers were blended and converted to fiber webs in the air‐laying process. Composite prepregs were then made from the fiber webs. The prepregs were finally converted to composites by compression molding. The relationship between the main process variables and the properties of the biocomposite was investigated. It was found that with increasing flax content, the mechanical properties increased. The maximum tensile strength of 80.3 MPa, flexural strength of 138.5 MPa, tensile modulus of 9.9 GPa and flexural modulus of 7.9 GPa were achieved. As the molding temperature and molding time increased, the mechanical properties decreased. The thermal and morphological properties of the biocomposites were also studied. The appropriate processing parameters for the biocomposites were established for different fiber contents. POLYM. COMPOS., 34:1611–1619, 2013. © 2013 Society of Plastics Engineers     

Biobased composites prepared by compression molding with a novel thermoset resin from soybean oil and a natural‐fiber reinforcement

Biobased composites were manufactured with a compression‐molding technique. Novel thermoset resins from soybean oil were used as a matrix, and flax fibers were used as reinforcements. The air‐laid fibers were stacked randomly, the woven fabrics were stacked crosswise (0/90°), and impregnation was performed manually. The fiber/resin ratio was 60 : 40. The prepared biobased composites were characterized by impact and flexural testing. Scanning electron microscopy of knife‐cut cross sections of the specimens was also done to investigate the fiber–matrix interface. Thermogravimetric analysis of the composites was carried out to provide indications of thermal stability. Three resins from soybean oil [methacrylated soybean oil, methacrylic anhydride modified soybean oil (MMSO), and acetic anhydride modified soybean oil] were used as matrices. The impact strength of the composites with MMSO resin reinforced with air‐laid flax fibers was 24 kJ/m², whereas that of the MMSO resin reinforced with woven flax fabric was between 24 and 29 kJ/m². The flexural strength of the MMSO resin reinforced with air‐laid flax fibers was between 83 and 118 MPa, and the flexural modulus was between 4 and 6 GPa, whereas the flexural strength of the MMSO resin reinforced with woven fabric was between 90 and 110 MPa, and the flexural modulus was between 4.87 and 6.1 GPa. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of macromolecular coupling agent on the property of PP/GF composites

Silane‐grafted polypropylene manufactured by a reactive grafting process was used as the coupling agent in polypropylene/glass‐fiber composites to improve the interaction of the interfacial regions. Polypropylene reinforced with 30% by weight of short glass fibers was injection‐molded and the mechanical behaviors were investigated. The results indicate that the mechanical properties (tensile strength, tensile modulus, flexural strength, flexural modulus, and Izod impact strength) of the composite increased remarkably as compared with the noncoupled glass fiber/polypropylene. SEM of the fracture surfaces of the coupled composites shows a good adhesion at the fiber/matrix interface: The fibers are coated with matrix polymer, and a matrix transition region exists near the fibers. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1537–1542, 1999     

Thermoplastic composites based on poly(ethylene 2,6‐naphthalate) and basalt woven fabrics: Static and dynamic mechanical properties

Composites based on poly(ethylene 2,6‐naphthalate) and basalt woven fabrics have been investigated with the aim to develop composites with a minimum service temperature of 100°C. Laminates have been manufactured by using the film‐stacking technique. A very low void content and a good fabric impregnation has been obtained as confirmed by the morphological analysis performed with scanning electron microscopy. Static flexural modulus and strength have been measured at 20, 60, and 100°C and compared with the dynamic mechanical behavior, evaluated from −100 to 220°C. A very good agreement has been detected between static and dynamic tests, proving that the dynamic mechanical analysis can be used to estimate the flexural modulus in a wide temperature range. Poly(ethylene 2,6‐naphthalate)/basalt composites have exhibited (at 20°C) a flexural modulus and strength as high as 20 GPa and 320 MPa, respectively. The flexural modulus and the flexural strength at 100°C have been found to be equal to 18 GPa and 230 MPa, confirming that this system can retain very good mechanical properties at a service temperature of 100°C. POLYM. COMPOS., 37:2549–2556, 2016. © 2015 Society of Plastics Engineers     

Corn oil‐based composites reinforced with continuous glass fibers: Fabrication and properties

Novel thermosetting composites have been successfully developed using glass fibers to reinforce regular corn oil (COR) and conjugated corn oil (CCOR) resins prepared by cationic copolymerization with styrene (ST) and divinylbenzene (DVB). The dependence of morphology and physical properties of the composites on the contents of glass fibers and DVB was determined by scanning electron microscopy, dynamic mechanical analysis, thermogravimetric analysis and tensile testing. The glass fiber loading and polymer matrix composition play an important role in improving the mechanical properties and thermal stability of the resulting composites. As the glass fiber content increases from 0 to 45 wt %, the COR‐based composites show an increase in Young's modulus from 4.1 to 874 MPa and tensile strength from 1.7 to 8.4 MPa. Furthermore, the composites exhibit good damping properties and are suitable for applications where reduction of both unwanted noise and vibration is important. Compared with the composites from COR, the CCOR‐based composites exhibit slightly higher thermal stabilities and mechanical properties, due to higher reactivity of CCOR with comonomers. Increasing the DVB content improves the crosslink density of the polymer matrix, leading to a significant improvement in the thermal stabilities and mechanical properties of the resulting composites. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:3345–3353, 2006     

Biocomposites composed of epoxidized soybean oil cured with terpene‐based acid anhydride and cellulose fibers

Epoxidized soybean oil (ESO) was cured with a terpene‐based acid anhydride (TPAn) at 150°C, and the thermal and mechanical properties of the cured product were compared with ESO cured with hexahydrophthalic anhydride (HPAn), maleinated linseed oil (LOAn), or thermally latent cationic polymerization catalyst (CPI). The ESO‐TPAn showed a higher glass transition temperature (67.2°C) measured by dynamic mechanical analysis than ESO‐HPAn (59.0°C), ESO‐LOAn (?41.0°C), and ESO‐CPI (10.0°C). The storage modulus at 20°C of ESO‐TPAn was higher than those of ESO‐LOAn and ESO‐CPI. Also, ESO‐TPAn showed higher tensile strength and modulus than the other cured ESOs. Regarding the biodegradability measured by biochemical oxygen demand in an activated sludge, ESO‐TPAn possessed some biodegradability, which was lower than that of ESO‐LOAn. Next, biocomposites composed of ESO‐TPAn and regenerated cellulose (lyocell) fabric were prepared by compression molding method. The tensile strength of ESO‐TPAn/lyocell composites increased with increasing fiber content. The tensile strength and modulus of ESO‐TPAn/lyocell composite with fiber content 75 wt % were 65 MPa and 2.3 GPa, which were three times higher than those of ESO‐TPAn. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and properties of an oxide fiber‐reinforced silica matrix composite

Oxide (Nextel? 440) fiber‐reinforced silica composites, with the density and porosity of 1.97 g/cm³ and 21.8%, were prepared through sol‐gel. Their average flexure strength, elastic modulus, shear strength, and fracture toughness at room temperature were 119.7 MPa, 25.6 GPa, 10.8 MPa, and 4.0 MPa·m^1/2, respectively. The composites showed typical toughened fracture behavior, and distinct pullout fibers were observed at the fracture surface. Their mechanical properties were performant up to 1000°C, with the maximum flexural strength of 132.2 MPa at 900°C. Moreover, the composites showed good thermal stability, even after thermal aging and thermal shock at elevated temperatures.     

Morphology and mechanical properties of unidirectional sisal– epoxy composites

Plant fibers are of increasing interest for use in composite materials. They are renewable resources and waste management is easier than with glass fibers. In the present study, longitudinal stiffness and strength as well as morphology of unidirectional sisal–epoxy composites manufactured by resin transfer molding (RTM) were studied. Horseshoe‐shaped sisal fiber bundles (technical fibers) were nonuniformly distributed in the matrix. In contrast to many wood composites, lumen was not filled by polymer matrix. Technical sisal fibers showed higher effective modulus when included in the composite material than in the technical fiber test (40 GPa as compared with 24 GPa). In contrast, the effective technical fiber strength in the composites was estimated to be around 400 MPa in comparison with a measured technical fiber tensile strength of 550 MPa. Reasons for these phenomena are discussed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2358–2365, 2002     

Bio‐composites for structural applications: Poly‐l‐lactide reinforced with long sisal fiber bundles

Fully bio‐based and biodegradable composites were compression molded from unidirectionally aligned sisal fiber bundles and a polylactide polymer matrix (PLLA). Caustic soda treatment was employed to modify the strength of sisal fibers and to improve fiber to matrix adhesion. Mechanical properties of PLLA/sisal fiber composites improved with caustic soda treatment: the mean flexural strength and modulus increased from 279 MPa and 19.4 GPa respectively to 286 MPa and 22 GPa at a fiber volume fraction of V_f = 0.6. The glass transition temperature decreased with increasing fiber content in composites reinforced with untreated sisal fibers due to interfacial friction. The damping at the caustic soda‐treated fibers‐PLLA interface was reduced due to the presence of transcrystalline morphology at the fiber to matrix interface. It was demonstrated that high strength, high modulus sisal‐PLLA composites can be produced with effective stress transfer at well‐bonded fiber to matrix interfaces. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40999.     

The Properties of Woven Kenaf and Betel Palm (Areca catechu) Reinforced Unsaturated Polyester Composites

The use of woven betel palm and kenaf lignocellulosic fibers as a reinforcing phase in unsaturated polyester was reported. The morphology, physical properties, and mechanical properties of the natural fibers and resulting woven composites were evaluated. Kenaf fibers exhibit higher tensile properties than betel palm fibers due to the higher amount of cellulose content. From the morphology observation, it is found that the alkaline treatment of the fibers effectively clean the fiber surface and increase the fiber surface roughness. Comparison between treated and untreated woven betel palm and kenaf composites at 7 vol% of fiber content was carried out. Interestingly, untreated woven kenaf composites exhibit comparable flexural strength with those of untreated woven betel palm composites. However, untreated kenaf composites exhibit superior flexural modulus to those of betel palm composites. In general, mechanical properties of the woven composites made from alkali-treated fibers were superior to the untreated fibers.     

Effect of interphase on mechanical properties and microstructures of 3D Cf/SiBCN composites at elevated temperatures

Interphase between the fibers and matrix plays a key role on the properties of fiber reinforced composites. In this work, the effect of interphase on mechanical properties and microstructures of 3D C_f/SiBCN composites at elevated temperatures was investigated. When PyC interphase is used, flexural strength and elastic modulus of the C_f/SiBCN composites decrease seriously at 1600°C (92 ± 15 MPa, 12 ± 2 GPa), compared with the properties at room temperature (371 ± 31 MPa, 31 ± 2 GPa). While, the flexural strength and elastic modulus of C_f/SiBCN composites with PyC/SiC multilayered interphase at 1600°C are as high as 330 ± 7 MPa and 30 ± 2 GPa, respectively, which are 97% and 73% of the values at room temperature (341 ± 20 MPa, 41 ± 2 GPa). To clarify the effect mechanism of the interphase on mechanical properties of the C_f/SiBCN composites at elevated temperature, interfacial bonding strength (IFBS) and microstructures of the composites were investigated in detail. It reveals that the PyC/SiC multilayered interphase can retard the SiBCN matrix degradation at elevated temperature, leading to the high strength retention of the composites at 1600°C.     

Biocomposites developed using water‐plasticized wheat gluten as matrix and jute fibers as reinforcement

Biocomposites developed from wheat gluten using water without any chemicals as plasticizer and jute fibers as reinforcement have much better flexural and tensile properties than similar polypropylene composites reinforced with jute fibers. Wheat gluten is an inexpensive and abundant co‐product derived from renewable resources and is biodegradable but non‐thermoplastic. Previous attempts at developing biocomposites from wheat gluten have used plasticizers such as glycerol or chemical modifications to make gluten thermoplastic. However, plasticizers have a considerably negative effect on the mechanical properties of the composites and chemical modifications make wheat gluten less biodegradable, expensive and/or environmentally unfriendly. In the research reported, we developed composites from wheat gluten using water as a plasticizer without any chemicals. Water plasticizes wheat gluten but evaporates during compression molding and therefore does not affect the mechanical properties of the composites. The effect of composite fabrication conditions on the flexural, tensile and acoustic properties was studied in comparison to polypropylene composites reinforced with jute fibers. Wheat gluten composites had flexural strength (20 MPa), tensile strength (69 MPa) and tensile modulus (7.7 GPa) values approximately twice those of polypropylene composites. Water is an effective plasticizer for wheat gluten and could be used to develop various types of inexpensive and biodegradable wheat gluten‐based thermoplastics. Copyright © 2011 Society of Chemical Industry     

Influence of alkali fiber treatment and fiber processing on the mechanical properties of hemp/epoxy composites

Industrial hemp fibers were treated with a 5 wt % NaOH, 2 wt % Na₂SO₃ solution at 120°C for 60 min to remove noncellulosic fiber components. Analysis of fibers by lignin analysis, scanning electron microscopy (SEM), zeta potential, Fourier transform infrared (FTIR) spectroscopy, wide angle X‐ray diffraction (WAXRD) and differential thermal/thermogravimetric analysis (DTA/TGA), supported that alkali treatment had (i) removed lignin, (ii) separated fibers from their fiber bundles, (iii) exposed cellulose hydroxyl groups, (iv) made the fiber surface cleaner, and (v) enhanced thermal stability of the fibers by increasing cellulose crystallinity through better packing of cellulose chains. Untreated and alkali treated short (random and aligned) and long (aligned) hemp fiber/epoxy composites were produced with fiber contents between 40 and 65 wt %. Although alkali treatment generally improved composite strength, better strength at high fiber contents for long fiber composites was achieved with untreated fiber, which appeared to be due to less fiber/fiber contact between alkali treated fibers. Composites with 65 wt % untreated, long aligned fiber were the strongest with a tensile strength (TS) of 165 MPa, Young's modulus (YM) of 17 GPa, flexural strength of 180 MPa, flexural modulus of 9 GPa, impact energy (IE) of 14.5 kJ/m², and fracture toughness (K_Ic) of 5 MPa m^1/2. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of alkaline treatment on physical,mechanical, and thermal characteristics of jute filler reinforced epoxy composites

With burgeoning environmental concerns worldwide, using natural fibers/fillers to produce composites rather than conventional fibers is on the rise. The current work focuses on the physical and thermomechanical characteristics of alkaline-treated jute filler-based epoxy composites. The composites have been prepared with different weight fraction of jute fillers (0%, 2.5%, 5%, 7.5%, 10%, and 12.5%) using hand layup process. The X-ray diffraction and Fourier transform infrared spectroscopy analysis observed that the alkali treatment of jute fillers improved the crystallinity and molecular structure, enhancing the interfacial and molecular bond between fillers and matrix. The mechanical characterizations of developed composites analyzed that the inclusion of treated jute fillers strengthened the tensile and flexural properties. The 5% filler-based composites have demonstrated maximum tensile strength (54.06 MPa) and modulus (3.12 GPa) with maximum flexural strength (67.55 MPa) and modulus (3.90 GPa). The viscoelastic characteristics of composites revealed that the 7.5% filler-based composite has the highest storage modulus (3.75 GPa), loss modulus (0.496 GPa), and glass transition temperature (91°C) due to greater interfacial interactions of molecules. The weight loss and degradation of composites analyzed with thermogravimetric analysis, and observed better thermal stability with treated jute fillers. The morphological analysis at fracture surfaces analyzed the brittle catastrophic failure of composites. Therefore, the finding produced better specific strength and stiffness with greater thermal stability for electronics equipment, packaging, and transportation.     

Synthesis and characterization of chlorinated soy oil based epoxy resin/glass fiber composites

Composites with good toughness properties were prepared from chemically modified soy epoxy resin and glass fiber without additional petroleum based toughening agent. Chlorinated soy epoxy (CSE) resin was prepared from soybean oil. The CSE was characterised by spectral, and titration method. The prepared CSE was blended with commercial epoxy resin in different ratios and cured at 85°C for 3 h, and post cured at 225°C for 2 h using m‐phenylene diamine (MPDA) as curing agent. The cure temperatures of epoxy/CSE/MPDA with different compositions were found to be in the range of (151.2–187.5°C). The composite laminates were fabricated using epoxy /CSE/MPDA‐glass fiber at different compositions. The mechanical properties such as tensile strength (248–299 MPa), tensile modulus (2.4–3.4 GPa), flexural strength (346–379 MPa), flexural modulus (6.3–7.8 GPa) and impact strength (29.7–34.2) were determined. The impact strength increased with the increase in the CSE content. The interlaminor fracture toughness (G_IC) values also increased from 0.6953 KJ/m² for neat epoxy resin to 0.9514 KJ/m² for 15%CSE epoxy‐modified system. Thermogravimetric studies reveal that the thermal stability of the neat epoxy resin was decreased by incorporation of CSE. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Evaluation of interfacial properties and microfailure mechanisms in single fiber‐reinforced epoxy composites at low temperature

In this preliminary study, micromechanical techniques were used to compare the interfacial properties of both carbon and glass fiber composites with two structurally different epoxy matrices (YD‐114 and YDF‐175) at ambient and relatively low temperatures (25°C and −10°C). Tensile modulus of elasticity for both epoxies was higher at lower temperature. Although both fibers exhibited more bimodality at lower temperature than at ambient temperature, glass fiber composites exhibited a statistically greater improvement in tensile strength. This may be attributed to differences in inherent flaws and rigidity. A decrement in stress was observed for YDF‐175 epoxy composites under cyclic loadings at both temperatures, which was attributed to lower interfacial shear strength (IFSS). In contrast to the IFSS of conventional YD‐114 epoxy composites, the IFSS of both the carbon and glass fibers/YDF‐175 epoxy composites studied was higher at the lower temperature. The microfailure pattern observed in microdroplet pullout tests was consistent with the other IFSS results. POLYM. COMPOS., 2012. © 2011 Society of Plastics Engineers