Non‐invasive chaos control of DC–DC converter and its optimization

The frequency‐domain‐based realization condition related to a novel non‐invasive chaos control is presented in this paper. According to the common piecewise‐linear characteristics of PWM‐controlled DC–DC converter system, a general expression for its Jacobian matrix is derived for optimizing the control parameters of the proposed non‐invasive chaos control. The relevant simulation and experiment results about the application of the chaos control to a voltage‐mode Buck converter are given, which confirm the feasibility of the parameter‐optimization method and the validity of the proposed non‐invasive chaos control. Copyright © 2010 John Wiley & Sons, Ltd.     

A step‐up PWM DC–DC converter for renewable energy applications

A step‐up pulse width modulation (PWM) direct current (DC)–DC converter is presented in this paper, which has its origin in quasi Z‐source inverter. Analysis of this converter in steady state is presented, and relevant expressions are derived for the proposed converter operating in continuous conduction mode. The power loss expressions for each component of the converter are derived, and thereby, obtained expressions for overall converter efficiency are presented. Further, a dynamic model is derived to design an appropriate controller for this converter. The simulation and experimental results are presented to support the theoretical analysis. The advantages such as continuous input current, high step‐up gain at lower duty ratio, and common ground for source, load, and switch makes the converter suitable for renewable energy applications. Copyright © 2015 John Wiley & Sons, Ltd.     

Adaptive saturated finite‐time control algorithm for buck‐type DC‐DC converter systems

To enhance the convergent rate and robustness of buck‐type DC‐DC converter system, a new finite‐time voltage regulation control algorithm is proposed in this paper. First, an average state space‐based model is analyzed, which considers both the parameters uncertainties and the variations of load and input voltage. By using saturation finite‐time control theory, at the first step, in the absence of disturbance, a new fast voltage regulation control algorithm is designed, which can guarantee that the output voltage converges to the reference voltage in a finite time. Because the saturation constraint is considered during the controller design, the duty ratio function of the converter satisfies the constraint between 0 and 1. Second, in the presence of disturbance, a finite‐time convergent disturbance observer is designed to estimate the unknown disturbances in a finite time. Finally, a disturbance observer‐based finite‐time voltage regulation control algorithm is developed. Compared with PI (Proportional‐Integral) control algorithm, circuit simulations show that the proposed algorithm has a faster regulation performance and stronger robustness performance on disturbance rejection.     

A novel low‐loss control strategy for bidirectional DC–DC converter

Bidirectional DC–DC converter with phase‐shift control is commonly used for hybrid electric vehicle and fuel‐cell vehicle applications. This converter is characterized by simple circuit topology and soft‐switching implementation without additional devices. Despite these advantages, the efficiency is poor at light load condition because of high switching and conduction losses caused by high RMS inductor current. To achieve zero‐voltage switching (ZVS) for all power MOSFETs, a constant offset inductor current is maintained to conduct the antiparallel body diodes before MOSFETs turn on. A control strategy of combining duty ratio and phase‐shift modulation is proposed to reach the constant offset current. By reaching the constant offset current, the RMS inductor current can be reduced significantly, and ZVS can be achieved in all load variation ranges, resulting in high efficiency. A 2.5‐kW prototype is implemented to verify the control scheme, and a minimum efficiency of 97.3% is achieved at light load condition. Copyright © 2017 John Wiley & Sons, Ltd.     

Fast‐transient DC‐DC converter using a high‐performance error amplifier with a rapid output‐voltage control technique

This letter presents a method for improving the transient response of DC‐DC converters. The proposed technique replaces the conventional error amplifier with a combination of two different amplifiers to achieve a high loop gain and high slew rate. In addition, a rapid output‐voltage control circuit is employed to further reduce the recovery time. The proposed technique was applied to a four‐phase buck converter, and the chip was implemented using a 0.18‐μm CMOS process. The switching frequency of each phase was set at 2 MHz. Using a supply voltage of 2.7–5.5 V and an output voltage of 0.6–1.5 V, the regulator provided up to 2‐A load current with maximum measured recovery time of only 6.2 and 6.5 μs for increasing and decreasing load current, respectively. Copyright © 2017 John Wiley & Sons, Ltd.     

Harmonic balance‐based control of a boost DC/AC converter

The achievement of step‐up inversion with a boost DC/AC converter requires appropriate periodic references for inductor currents, which have to satisfy ordinary differential equations (ODE) of the Abel type. These are equations with highly unstable solutions for which the existence of periodic solutions remains unproved. Hence, the studies reported so far in this subject obtain periodic output voltages that approximately track the expected profile using different periodic current references that do not exactly satisfy the Abel ODE. However, neither an explanation of why are periodic output voltages still obtained, nor an assessment of the output voltage error is provided. This paper analyzes the effect of using periodic current references in a Lyapunov‐based controlled boost DC/AC converter performing step‐up inversion tasks. It is shown that, for sufficiently accurate current references, the system exhibits asymptotically stable periodic solutions with bounded error. Moreover, the paper propounds the use of Harmonic Balance (HB)‐based techniques to obtain such current references. Simulation and experimental results confirm that this choice yields periodic output voltages with an error that may be lowered using higher HB approximations. Copyright © 2011 John Wiley & Sons, Ltd.     

LLC resonant DC–DC converter with series‐connected primary windings of transformer

This paper proposes a zero‐voltage switching (ZVS) LLC resonant step up DC–DC converter with series‐connected primary windings of the transformer. The series resonant inverter in the proposed topology has two power switches (MOSFETs), two resonant capacitors, two resonant inductors, and only one transformer with center‐tapped primary windings. The power switches are connected in the form of a half‐bridge network. Resonant capacitors and inductors along with the primary windings of the transformer form two series resonant circuits. The series resonant circuits are fed alternately by operating the power switches with an interleaved half switching cycle. The secondary winding of transformer is connected to a bridge rectifier circuit to rectify the output voltage. The converter operates within a narrow frequency range below the resonance frequency to achieve ZVS, and its output power is regulated by pulse frequency modulation. The converter has lower conduction and switching losses and therefore higher efficiency. The experimental results of a 500‐W prototype of proposed converter are presented. The results confirm the good operation and performance of the converter. © 2014 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Multistage multiphase switched‐capacitor DC–DC converter with variable‐phase and PWM control

A closed‐loop multistage multiphase switched‐capacitor converter (n‐stage p‐phase MPSC) is proposed with a variable‐phase control (VPC) and a pulse‐width‐modulation (PWM) technique for low‐power step‐up conversion and high‐efficiency regulation. In this n‐stage MPSC, n voltage doublers are connected in series for boosting the voltage gain up to 2ⁿ at most. Here, VPC is suggested to realize a variable multiphase operation by changing the phase number p and topological path for the more suitable level of voltage gain so as to improve the power efficiency, especially for the lower output voltage Besides, PWM is adopted not only to enhance output regulation for different desired outputs, but also to reinforce output robustness to source/loading variation. Further, some theoretical analyses and designs include: n‐stage p‐phase MPSC model, steady‐state analysis, conversion ratio, power efficiency, output ripple, stability, capacitance selection, and control design. Finally, the closed‐loop MPSC is simulated, and the hardware is implemented and tested. All the results are illustrated to show the efficacy of the proposed scheme. Copyright © 2011 John Wiley & Sons, Ltd.     

Pulse current regenerative resonant snubber‐assisted two‐switch flyback‐type ZVS PWM DC‐DC converter

In this paper, a two‐switch high‐frequency flyback transformer‐type zero voltage soft‐switching PWM DC‐DC converter using IGBTs is proposed. Effective applications for this power converter can be found in auxiliary power supplies of rolling stock transportation and electric vehicles. This power converter is basically composed of two active power switches and a flyback high‐frequency transformer. In addition to these, two passive lossless snubbers with power regeneration loops for energy recovery, consisting of a three‐winding auxiliary high‐frequency transformer, auxiliary capacitors and diodes are introduced to achieve zero voltage soft switching from light to full load conditions. Furthermore, this power converter has some advantages such as low cost circuit configuration, simple control scheme, and high efficiency. Its operating principle is described and to determine circuit parameters, some practical design considerations are discussed. The effectiveness of the proposed power converter is evaluated and compared with the hard switching PWM DC‐DC converter from an experimental point of view, and the comparative electromagnetic conduction and radiation noise characteristics of both DC‐DC power converter circuits are also depicted. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 152(3): 74–81, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20081     

An interleaved high step‐up DC‐DC converter with double boost paths

This paper proposed a novel high step‐up converter with double boost paths. The circuit uses two switches and one double‐path voltage multiplier cell to own the double boost and interleaved effects simultaneously. The voltage gain ratio of the proposed DC‐DC converter can be three times the ratio of the conventional boost converter such that the voltage stress of the switch can be lower. The high step‐up performance is in accordance with only one double‐path voltage multiplier cell. Therefore, the number of diodes and capacitors in the proposed converter can be reduced. Furthermore, the interleaved property of the proposed circuit can reduce the losses in the rectifier diode and capacitor. The prototype circuit with 24‐V input voltage, 250‐V output voltage, and 150‐W output power is experimentally realized to verify the validity and effectiveness of the proposed converter. Copyright © 2014 John Wiley & Sons, Ltd.     

Series resonant high‐voltage DC–DC converter with reduced component count

This paper proposes a novel zero‐current‐switching series resonant high‐voltage DC–DC converter with reduced component count. The series resonant inverter in the proposed topology has two power switches (insulated‐gate bipolar transistors, IGBTs), two resonant capacitors, and only one high‐voltage transformer (HVT) with center‐tapped primary windings. The power switches are connected in the form of a half‐bridge network. The leakage inductances of the transformer's primary windings together with the resonant capacitors form two series resonant circuits. The series resonant circuits are fed alternately by operating the power switches with interleaved half switching cycle. The secondary winding of the HVT is connected to a bridge rectifier circuit to rectify the secondary voltage. The converter operates in the discontinuous conduction mode (DCM) and its output voltage is regulated by pulse frequency modulation. Therefore, all the power switches turn on and off at the zero‐current switching condition. The main features of the proposed converter are its lower core loss, lower cost, and smaller size compared to previously proposed double series resonant high voltage DC–DC converters. The experimental results of a 130‐W prototype of the proposed converter are presented. The results confirm the excellent operation and performance of the converter. © 2016 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Design of a ZVS PWM DC–DC converter for high gain applications

In this paper, a pulse width modulation DC‐DC converter with high step‐up voltage gain is proposed. The proposed converter achieves high step‐up voltage gain with appropriate duty ratio, coupled inductor, and voltage multiplier technique. The energy stored in the leakage inductor of the coupled inductor can be recycled in the proposed converter. Moreover, because both main and auxiliary switches can be turned on with zero‐voltage switching, switching loss can be reduced by soft‐switching technique. So the overall conversion efficiency is improved significantly. The theoretical steady‐state analyses and the operating principles of the proposed converter are discussed in detail for both continuous conduction mode and discontinuous conduction mode. Finally, a laboratory prototype circuit of the proposed converter is implemented to verify the performance of the proposed converter. Copyright © 2015 John Wiley & Sons, Ltd.     

DC analysis and design of a PWM buck converter operated as a dynamic power supply

Modern energy transmission and signal reproduction techniques rely upon power amplifiers that must operate with high efficiency. An increasingly popular technique for addressing this problem involves replacing the fixed power amplifier supply voltage V _{D D} with a controlled, variable voltage provided by a dynamic power supply. Although pulse‐width modulated dc‐dc buck converters typically function as fixed‐output supplies, this paper provides new theoretical dc analysis for operation wherein the output voltage is controlled and continuously variable over a wide range. A design procedure for the variable‐output buck converter is derived. Key device parameters affecting converter speed and efficiency are identified. The dc analysis and design procedure are verified experimentally, with calculated and measured parameters shown to be in good agreement. Copyright © 2016 John Wiley & Sons, Ltd.     

Analysis and implementation of a high‐efficiency zero‐voltage‐zero‐current‐switching DC–DC converter

A high‐efficiency zero‐voltage‐zero‐current‐switching DC–DC converter with ripple‐free input current is presented. In the presented converter, the ripple‐free boost cell provides ripple‐free input current and zero‐voltage switching of power switches. The resonant flyback cell provides zero‐voltage switching of power switches and zero‐current switching of the output diode. Also, it has a simple output stage. The proposed converter achieves high efficiency because of the reduction of the switching losses of the power switches and the output diode. Detailed analysis and design of the proposed converter are carried out. A prototype of the proposed converter is developed and its experimental results are presented for validation. Copyright © 2011 John Wiley & Sons, Ltd.     

Modelling cross‐regulation in a single switched capacitor DC‐DC converter

The letter proposes to model cross‐regulation in a dual‐output switched capacitor converter (SCC) by three equivalent resistances connected in delta circuit. It is shown that as opposed to linear equivalent (output) resistance of single‐output SCCs, these resistances are voltage‐controlled. The obtained analytical expressions have been verified by simulations and give correct results even if the output voltages change in wide range. The proposed analysis paves the way for modelling cross‐regulation in complex SCCs with multiple topologies and can be useful in studies of crosstalk through parasitic capacitances on chip.     

A ZVS‐ZCS phase shift full bridge DC‐DC converter with secondary‐side control for battery charging applications

The output power requirement of battery charging circuits can vary in a wide range, hence making the use of conventional phase shift full bridge DC‐DC converters infeasible because of poor light load efficiency. In this paper, a new ZVS‐ZCS phase shift full bridge topology with secondary‐side active control has been presented for battery charging applications. The proposed circuit uses 2 extra switches in series with the secondary‐side rectifier diodes, operating with phase shift PWM. With the assistance of transformer's magnetizing inductance, the proposed converter maintains zero voltage switching (ZVS) of the primary‐side switches over the entire load range. The secondary‐side switches regulate the output voltage/current and perform zero current switching (ZCS) independent of the amount of load current. The proposed converter exhibits a significantly better light load efficiency as compared with the conventional phase shift full bridge DC‐DC converter. The performance of the proposed converter has been analyzed on a 1‐kW hardware prototype, and experimental results have been included.     

A switch‐mode boost DC–DC converter for IR‐drop compensation of charging cable

A switch‐mode boost DC–DC converter has been developed to compensate for the IR‐drop because of the finite resistance of a charging cable. The boost ratio of the DC–DC converter is adaptively controlled by an IR‐drop sensing circuit to provide the required voltage level to a battery charger regardless of the cable resistance. Implemented in a 0.18 µm BCDMOS process, the IR‐drop compensating switch‐mode boost DC–DC converter occupies 6.2 mm² active area and shows the 93.2% peak efficiency. The proposed IR‐drop compensating boost converter can be applied to compensate for the IR‐drop of any type of charging cables. Copyright © 2014 John Wiley & Sons, Ltd.     

Single‐Inductor Dual‐Output DC–DC Converter Design Using RC Ripple Regulator Method

In this paper, we have proposed Single‐Inductor Dual‐Output (SIDO) buck–buck and boost–boost dc–dc converter using improved RC ripple regulator control. The proposed SIDO buck–buck converter has the characteristics of low‐ripple and high control frequency. RC ripple regulator control cannot be applied to SIDO boost–boost converter because RC ripple regulator undergoes self‐excited oscillation and two self‐excited oscillating controllers make the SIDO converter unstable. Thus we proposed the priority circuit for RC ripple regulator control. The proposed control circuit improves response characteristic and simplicity of the control circuit. Simulations are performed to verify the validity of the proposed SIDO converter. Simulation results indicate good performance of the proposed SIDO converter.     

DC/DC变换器Buck电路建模分析与控制研究

首先运用状态空间法建立基于超级电容的双向DC/DC变换器Buck电路模式的数学模型,应用开关周期平均值以及欧拉公式对其进行分析,并引入小信号扰动,分离扰动并线性化后设计出Buck电路模型的控制方法—双闭环控制策略。最后搭建Simulink仿真以验证控制策略的有效性与正确性,其结果为超级电容的应用和研究提供参考。     

Dynamics of PFC power converters subject to time‐delayed feedback control

Power factor correction converters are power electronics circuits used as AC‐DC power supplies. These systems are well known to exhibit nonlinear phenomena such as subharmonic oscillations and chaotic regimes. These undesirable behaviors increase the THD and therefore can jeopardize enormously the system performances. In this paper, time delay feedback control is applied to stabilize a two‐stage power factor correction AC‐DC converter when it exhibits these instabilities under traditional controllers. This control technique introduces many advantages to the most and widely used average current mode control through widening the stability domain of the system. By appropriately selecting the time delay feedback gain and the time delay period, the undesirable subharmonic components are eliminated, whereas the desired ones remain unchanged. A harmonic balance approach is used for studying the dynamics of the system under the new control scheme and to obtain the stabilization domain. Copyright © 2010 John Wiley & Sons, Ltd.