Thermal properties and non‐isothermal crystallization behavior of poly(trimethylene terephthalate)/poly(lactic acid) blends

Thermal properties and non‐isothermal melt‐crystallization behavior of poly(trimethylene terephthalate) (PTT)/poly(lactic acid) (PLA) blends were investigated using differential scanning calorimetry and thermogravimetric analysis. The blends exhibit single and composition‐dependent glass transition temperature, cold crystallization temperature (T_cc) and melt crystallization peak temperature (T_mc) over the entire composition range, implying miscibility between the PLA and PTT components. The T_cc values of PTT/PLA blends increase, while the T_mc values decrease with increasing PLA content, suggesting that the cold crystallization and melt crystallization of PTT are retarded by the addition of PLA. The modified Avrami model is satisfactory in describing the non‐isothermal melt crystallization of the blends, whereas the Ozawa method is not applicable to the blends. The estimated Avrami exponent of the PTT/PLA blends ranges from 3.25 to 4.11, implying that the non‐isothermal crystallization follows a spherulitic‐like crystal growth combined with a complicated growth form. The PTT/PLA blends generally exhibit inferior crystallization rate and superior activation energy compared to pure PTT at the same cooling rate. The greater the PLA content in the PTT/PLA blends, the lower the crystallization rate and the higher the activation energy. Moreover, the introduction of PTT into PLA leads to an increase in the thermal stability behavior of the resulting PTT/PLA blends. Copyright © 2011 Society of Chemical Industry     

Enzymatic degradation of blends of poly(ε‐caprolactone) and poly(styrene‐co‐acrylonitrile) by Pseudomonas lipase

In polymer blends, the composition and microcrystalline structure of the blend near surfaces can be markedly different from the bulk properties. In this study, the enzymatic degradation of poly(ε‐caprolactone) (PCL) and its blends with poly(styrene‐co‐acrylonitrile) (SAN) was conducted in a phosphate buffer solution containing Pseudomonas lipase, and the degradation behavior was correlated with the surface properties and crystalline microstructure of the blends. The enzymatic degradation preferentially took place at the amorphous part of PCL film. The melt‐quenched PCL film with low crystallinity and small lamellar thickness showed a higher degradation rate compared with isothermally crystallized (at 36, 40, and 44°C) PCL films. Also, there was a vast difference in the enzymatic degradation behavior of pure PCL and PCL/SAN blends. The pure PCL showed 100% weight loss in a very short time (i.e., 72 h), whereas the PCL/SAN blend containing just 1% SAN showed ～50% weight loss and the degradation ceased, and the blend containing 40% SAN showed almost no weight loss. These results suggest that as degradation proceeds, the nondegradable SAN content increases at the surface of PCL/SAN films and prevents the lipase from attacking the biodegradable PCL chains. This phenomenon was observed even for a very high PCL content in the blend samples. In the blend with low PCL content, the inaccessibility of the amorphous interphase with high SAN content prevented the attack of lipase on the lamellae of PCL. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 868–879, 2002     

Reactive modification and compatibilization of poly(lactide) and poly(butylene adipate‐co‐terephthalate) blends with epoxy functionalized‐poly(lactide) for blown film applications

Biodegradable blown films comprising of poly(lactide) (PLA) and poly(butylene adipate‐co‐terephthalate) (PBAT) were produced using epoxy functionalized‐poly(lactide) (EF‐PLA) reactive modifiers for rheological enhancement and compatibilization. The epoxy groups on the EF‐PLA modifiers react with PBAT forming an in situ copolymer that localizes at the blend interphase resulting in compatibilization of the polymer blend components. The EF‐PLA modified polymer blends have improved melt strength and the resultant films showed better processability as seen by increased bubbled stability. This allowed for blown films with higher PLA content (70%) compared to the unmodified control films (40%). The static charge build‐up typically experienced with PLA film blowing was decreased with the inclusion of EF‐PLA yielding films with better slip and softness. The compatibilization effect of the EF‐PLA modifiers resulted in significant improvement in mechanical properties. For example, dart test performance was up to four times higher than the control, especially at higher PLA concentrations. Therefore, the rheological enhancement and compatibilization effects of the EF‐PLA reactive modifiers make them ideally suited to create high PLA content films. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43310.     

Poly(para‐dioxanone)/poly(D,L‐lactide) blends compatibilized with poly(D,L‐lactide‐co‐para‐dioxanone)

The effect of poly(D ,L ‐lactide‐co‐para‐dioxanone) (PLADO) as the compatibilizer on the properties of the blend of poly(para‐dioxanone) (PPDO) and poly(D ,L ‐lactide) (PDLLA) has been investigated. The 80/20 PPDO/PDLLA blends containing from 1% to 10% of random copolymer PLADO were prepared by solution coprecipitation. The PLADO component played a very important role in determining morphology, thermal, mechanical, and hydrophilic properties of the blends. Addition of PLADO into the blends could enhance the compatibility between dispersed PDLLA phase and PPDO matrix; the boundary between the two phases became unclear and even the smallest holes were not detected. On the other hand, the position of the T_g was composition dependent; when 5% PLADO was added into blend, the T_g distance between PPDO and PDLLA was shortened. The blends with various contents of compatibilizer had better mechanical properties compared with simple PPDO/PDLLA binary polymer blend, and such characteristics further improved as adding 5% random copolymers. The maximum observed tensile strength was 29.05 MPa for the compatibilized PPDO/PDLLA blend with 5% PLADO, whereas tensile strength of the uncompatibilized PPDO/PDLLA blend was 14.03 MPa, which was the lowest tensile strength. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of tacticity of poly(methyl methacrylate) on the miscibility with poly(styrene‐co‐acrylonitrile)

Isotactic, atactic, and syndiotactic poly(methyl methacrylates) (PMMAs) (designated as iPMMA, aPMMA, and sPMMA) with approximately the same molecular weight were mixed separately with poly(styrene‐co‐acrylonitrile) (abbreviated as PSAN) containing 25 wt % of acrylonitrile in tetrahydrofuran to make three polymer blend systems. Differential scanning calorimetry (DSC) was used to study the miscibility of these blends. The results showed that the tacticity of PMMA has a definite impact on its miscibility with PSAN. The aPMMA/PSAN and sPMMA/PSAN blends were found to be miscible because all the prepared films were transparent and showed composition dependent glass transition temperatures (T_gs). The glass transition temperatures of the two miscible blends were fitted well by the Fox equation, and no broadening of the glass transition regions was observed. The iPMMA/PSAN blends were found to be immiscible, because most of the cast films were translucent and had two glass transition temperatures. Through the use of a simple binary interaction model, the following comments can be drawn. The isotactic MMA segments seemed to interact differently with styrene and with acrylonitrile segments from atactic or syndiotactic MMA segments. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2894–2899, 1999     

Miscibility of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) with high molecular weight poly(lactic acid) blends determined by thermal analysis

An important strategy used in the polymer industry in recent years is blending two bio‐based polymers to attain desirable properties similar to traditional thermoplastics, thus increasing the application potential for bio‐based and bio‐degradable polymers. Miscibility of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) with poly(L ‐lactic acid) (PLA) were characterized using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). Three different grades of commercially available PLAs and one type of PHBV were blended in different ratios of 50/50, 60/40, 70/30, and 80/20 (PHBV/PLA) using a micro‐compounder at 175°C. The DSC and TGA analysis showed the blends were immiscible due to different stereo configuration of PLA polymer and two distinct melting temperatures. However, some compatibility between PHBV and PLA polymers was observed due to decreases in PLA's glass transition temperatures. Additionally, the blends do not show clear separation by SEM analysis, as observed in the thermal analysis. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Influence of phthalic anhydride and bioxazoline on the mechanical and morphological properties of biodegradable poly(lactic acid)/poly[(butylene adipate)‐co‐terephthalate] blends

Poly(lactic acid) (PLA)/poly[(butylene adipate)‐co‐terephthalate] (PBAT) blends were fabricated by melt blending, with 2,2′‐(1,3‐phenylene)bis(2‐oxazoline) (BOZ) and phthalic anhydride (PA) used as compatibilizers. It was found that a small amount of BOZ or PA greatly increased the elongation at break of the PLA/PBAT blends without sacrificing their high tensile strength. Scanning electron microscopy results revealed that the PBAT particles became finer and were uniformly dispersed in the matrix when the compatibilizers were incorporated, which indicated that the interfacial bonding and compatibilization between PLA and PBAT were improved in the presence of the compatibilizers. Compared with PLA/PBAT blends, the molecular weight of PLA/PBAT/PA/BOZ blends was increased due to chain‐extending reactions. Differential scanning calorimetry results suggested PBAT decreased the crystallization rate and crystallinity of PLA in the blends. Moreover, the glass transition temperature of PBAT was further decreased when the compatibilizers were used. © 2013 Society of Chemical Industry     

In situ fibre‐reinforced composite films of poly(lactic acid)/low‐density polyethylene blends: effects of composition on morphology,transport and mechanical properties

This study aimed to investigate the effects of blend composition on packaging‐related properties of poly(lactic acid) (PLA) and low density polyethylene (LDPE) blown films. Blend films with PLA contents of 5–20 wt% were produced and compared. Scanning electron micrographs of cross‐sectional cryofractured surfaces of the blend films revealed that in situ fibre‐reinforced composites were obtained. Viscosity ratio of the polymer components of ca 1 confirmed that fibre formation was favourable for this blend system. PLA microdomains were dispersed throughout the film in forms of long fibres (length‐to‐diameter ratio > 100) and ribbons. The number of fibres and ribbons increased with an increase of PLA content. Critical content of PLA was found to be 20 wt% for effective improvement of both moduli and gas barrier properties. Incorporation of poly[ethylene‐co‐(methyl acrylate)] compatibilizer showed minimal effect on PLA structure. However, it did improve moduli and O₂ barrier properties when sufficient amount (1.5 pph) was used in 10 wt% PLA/LDPE. In short, flow behaviour, ratio of polymer components and degree of compatibility together played intricate roles in the morphology and hence mechanical and transport properties of PLA/LDPE immiscible blends. © 2017 Society of Chemical Industry     

Mechanical properties and morphological changes of poly(lactic acid)/polycarbonate/poly(butylene adipate‐co‐terephthalate) blend through reactive processing

The mechanical properties and morphological changes of poly(lactic acid) (PLA), polycarbonate (PC), and poly(butylene adipate‐co‐terephthalate) (PBAT) polymer blends were investigated. Several types of blend samples were prepared by reactive processing (RP) with a twin‐screw extruder using dicumyl peroxide (DCP) as a radical initiator. Dynamic mechanical analyses (DMA) of binary polymer blends of PC/PBAT indicated that each component was miscible over a wide range of PC/PBAT mixing ratios. DMA of PLA/PBAT/PC ternary blends revealed that PBAT is miscible with PC even in the case of ternary blend system and the miscibility of PLA and PBAT can also be modified through RP. As a result, the tensile strain and impact strength of the ternary blends was increased considerably through RP, especially for PLA/PBAT/PC = 42/18/40 (wt/wt/wt) with DCP (0.3 phr). Scanning electron microscopy (SEM) analysis of the PLA/PBAT/PC blends revealed many small spherical island phases with a domain size of approximately 0.05–1 μm for RP, whereas it was approximately 10 μm without RP. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Orientation microstructure and properties of poly(propylene carbonate)/poly(butylene succinate) blend films

The blends of high molecular weight poly(propylene carbonate) (PPC) and poly(butylene succinate) (PBS) were melt blended using triphenylmethane triisocyanate (TTI) as a reactive coupling agent. TTI also serves as a compatibilizer for the blends of PPC and PBS. The blend containing 0.36 wt % TTI showed that the optimal mechanical properties were, therefore, calendared into films with different degrees of orientation. The calendering condition, degree of orientation, morphologies, mechanical properties, crystallization, and thermal behaviors of the films were investigated using wide‐angle X‐ray diffraction, scanning electron microscopy, tensile testing, and differential scanning calorimetry (DSC) techniques. The result showed that the as‐made films exhibited obvious orientation in machine direction (MD). Both tensile strength in MD and the tear strength in transverse direction (TD) increased with increasing the degree of orientation. The orientation of the film also increased the crystallinity and improved the thermal properties of the PPC/PBS blend films. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of poly(ethylene glycol) on the solid‐state polymerization of poly(ethylene terephthalate)

Poly(ethylene glycol) (PEG) and end‐capped poly(ethylene glycol) (poly(ethylene glycol) dimethyl ether (PEGDME)) of number average molecular weight 1000 g mol^?1 was melt blended with poly(ethylene terephthalate) (PET) oligomer. NMR, DSC and WAXS techniques characterized the structure and morphology of the blends. Both these samples show reduction in T_g and similar crystallization behavior. Solid‐state polymerization (SSP) was performed on these blend samples using Sb₂O₃ as catalyst under reduced pressure at temperatures below the melting point of the samples. Inherent viscosity data indicate that for the blend sample with PEG there is enhancement of SSP rate, while for the sample with PEGDME the SSP rate is suppressed. NMR data showed that PEG is incorporated into the PET chain, while PEGDME does not react with PET. Copyright © 2005 Society of Chemical Industry     

Compatibility,crystallinity and mechanical properties of poly(lactic acid)‐poly(ether‐block‐amide) based copper nanocomposites

Binary and ternary composites of poly(lactic acid) (PLA), poly(ether‐block‐amide) (PEBAX) and copper nanoparticles were prepared by melt blending in an internal mixer. Compatibility and molecular interactions between the three components of the nanocomposites were evaluated using scanning electron microscopy and Fourier transform infrared spectroscopy. It was found that the carbonyl groups of the PLA and copper nanoparticles interact. Also, PLA and PEBAX are compatible and develop molecular interactions between the C=O of PLA and the C=O and NH of PEBAX, forming dipole–dipole bonds and hydrogen bonds. The compatibility and molecular interaction between PLA and PEBAX are reduced by copper nanoparticles. The reduction of compatibility between PLA and PEBAX produced a lower storage modulus and lower strain at break in the ternary systems than in the blend PLA‐PEBAX. Copper nanoparticles enhanced the crystallinity of PLA. PLA responded more strongly to the nucleating effect of copper when PEBAX was added indicating a synergistic effect. The strain at break of PLA was enhanced by the addition of PEBAX but was severely reduced by the presence of nanoparticles. © 2020 Society of Chemical Industry     

Improving the toughening in poly(lactic acid)‐thermoplastic cassava starch reactive blends

Poly(lactic acid) (PLA), a physical blend of PLA and thermoplastic cassava starch (TPCS) (PLA‐TPCS), and reactive blends of PLA with TPCS using maleic anhydride as compatibilizer with two different peroxide initiators [i.e., 2,5‐bis(tert‐butylperoxy)‐2,5‐dimethylhexane (L101) and dicumyl peroxide (DCP)] PLA‐g‐TPCS‐L101 and PLA‐g‐TPCS‐DCP were produced and characterized. Blends were produced using either a mixer unit or twin‐screw extruder. Films for testing were produced by compression molding and cast film extrusion. Morphological, mechanical, thermomechanical, thermal, and optical properties of the samples were assessed. Blends produced with the twin‐screw extruder resulted in a better grade of mixing than blends produced with the mixer. Reactive compatibilization improved the interfacial adhesion of PLA and TPCS. Scanning electron microscopy images of the physical blend showed larger TPCS domains in the PLA matrix due to poor compatibilization. However, reactive blends revealed smaller TPCS domains and better interfacial adhesion of TPCS to the PLA matrix when DCP was used as initiator. Reactive blends exhibited high values for elongation at break without an improvement in tensile strength. PLA‐g‐TPCS‐DCP provides promising properties as a tougher biodegradable film. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46140.     

Physical properties of poly(vinyl chloride)–grafted N‐isopropylacrylamide graft copolymers and corresponding polyblends

The physical properties of poly(vinyl chloride) (PVC) and poly(N‐isopropylacrylamide) [poly(NIPAAm)] blend systems, and their corresponding graft copolymers such as PVC‐g‐NIPAAm, were investigated in this work. The compatible range for PVC–poly(NIPAAm) blend systems is less than 15 wt % poly(NIPAAm). The water absorbencies for the grafted films increase with increase in graft percentage. The water absorbencies for the blend systems increase with increase in poly(NIPAAm) content within the compatible range for the blends, but the absorbencies decrease when the amount of poly(NIPAAm) is more than the compatible range in the blend system. The tensile strengths for the graft copolymers are larger than the corresponding blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 170–178, 2000     

Morphology and properties of the biosourced poly(lactic acid)/poly(ethylene oxide‐b‐amide‐12) blends

Biosourced poly(lactic acid) (PLA) blends with different content of poly(ethylene oxide‐b‐amide‐12) (PEBA) were prepared by melt compounding. The miscibility, phase structure, crystallization behavior, mechanical properties, and toughening mechanism were investigated. The blend was an immiscible system with the PEBA domains evenly dispersed in the PLA matrix. The PEBA component suppressed the nonisothermal melt crystallization of PLA. With the addition of PEBA, marked improvement in toughness of PLA was achieved. The maximum for elongation at break and impact strength of the blend reached the level of 346% and 60.5 kJ/m², respectively. The phase morphology evolution in the PLA/PEBA blends after tensile and impact tests was investigated, and the corresponding toughening mechanism was discussed. It was found that the PLA matrix demonstrates obvious shear yielding in the blend during the tensile and impact tests, which induced energy dissipation and therefore lead to improvement in toughness of the PLA/PEBA blends. POLYM. COMPOS., 2013. © 2012 Society of Plastics Engineers     

Part 7. Effects of poly(L‐lactide‐co‐ϵ‐caprolactone) on morphology,structure, crystallization,and physical properties of blends of poly(L‐lactide) and poly(ϵ‐caprolactone)

Blended films of poly(L ‐lactide) [ie poly(L ‐lactic acid)] (PLLA) and poly(?‐caprolactone) (PCL) without or mixed with 10 wt% poly(L ‐lactide‐co‐?‐caprolactone) (PLLA‐CL) were prepared by solution‐casting. The effects of PLLA‐CL on the morphology, phase structure, crystallization, and mechanical properties of films have been investigated using polarization optical microscopy, scanning electron microscopy, differential scanning calorimetry and tensile testing. Addition of PLLA‐CL decreased number densities of spherulites in PLLA and PCL films, and improved the observability of spherulites and the smoothness of cross‐section of the PLLA/PCL blend film. The melting temperatures (T_m) of PLLA and PCL in the films remained unchanged upon addition of PLLA‐CL, while the crystallinities of PLLA and PCL increased at PLLA contents [X_PLLA = weight of PLLA/(weight of PLLA and PCL)] of 0.4–0.7 and at most of the X_PLLA values, respectively. The addition of PLLA‐CL improved the tensile strength and the Young modulus of the films at X_PLLA of 0.5–0.8 and of 0–0.1 and 0.5–0.8, respectively, and the elongation at break of the films at all the X_PLLA values. These findings strongly suggest that PLLA‐CL was miscible with PLLA and PCL, and that the dissolved PLLA‐CL in PLLA‐rich and PCL‐rich phases increased the compatibility between these two phases. © 2003 Society of Chemical Industry     

Miscibility and phase structure of binary blends of poly(L‐lactide) and poly(vinyl alcohol)

Blend films of poly(L ‐lactide) (PLLA) and poly(vinyl alcohol) (PVA) were obtained by evaporation of hexafluoroisopropanol solutions of both components. The component interaction, crystallization behavior, and miscibility of these blends were studied by solid‐state NMR and other conventional methods, such as Fourier transform infrared (FTIR) spectra, differential scanning calorimetry (DSC), and wide‐angle X‐ray diffraction (WAXD). The existence of two series of isolated and constant glass‐transition temperatures (T_g's) independent of the blend composition indicates that PLLA and PVA are immiscible in the amorphous region. However, the DSC data still demonstrates that some degree of compatibility related to blend composition exists in both PLLA/atactic‐PVA (a‐PVA) and PLLA/syndiotactic‐PVA (s‐PVA) blend systems. Furthermore, the formation of interpolymer hydrogen bonding in the amorphous region, which is regarded as the driving force leading to some degree of component compatibility in these immiscible systems, is confirmed by FTIR and further analyzed by ¹³C solid‐state NMR analyses, especially for the blends with low PLLA contents. Although the crystallization kinetics of one component (especially PVA) were affected by another component, WAXD measurement shows that these blends still possess two isolated crystalline PLLA and PVA phases other than the so‐called cocrystalline phase. ¹³C solid‐state NMR analysis excludes the interpolymer hydrogen bonding in the crystalline region. The mechanical properties (tensile strength and elongation at break) of blend films are consistent with the immiscible but somewhat compatible nature of these blends. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 762–772, 2001     

Improvement in toughness and crystallization of poly(L‐lactic acid) by melt blending with poly(epichlorohydrin‐co‐ethylene oxide)

Melt blending of poly(lactic acid) (PLA) and poly(epichlorohydrin‐co‐ethylene oxide) copolymers (ECO) was performed to improve the toughness and crystallization of PLA. Thermal and scanning electron microscopy analysis indicated that PLA and ECO were not thermodynamically miscible but compatible to some extent. The addition of a small amount of ECO accelerated the crystallization rate and increased the final crystallinity of PLA in the blends. Significant enhancement in toughness and flexibility of PLA were achieved by the incorporation of the ECO elastomer. When 20 wt% ECO added, the impact strength increased from 5 kJ/m² of neat PLA to 63.9 kJ/m², and the elongation at break increased from 5% to above 160%. The failure mode changed from brittle fracture of neat PLA to ductile fracture of the blend. Rheological measurement showed that the melt elasticity and viscosity of the blend increased with the concentration of ECO. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers.     

Preparation and properties of poly(ether‐ester‐amide)/poly(acrylonitrile‐co‐butadiene‐co‐styrene) antistatic blends

A novel antistatic agent poly(ether‐ester‐amide) (PEEA) based on caprolactam, polyethylene glycol, and 6‐aminocaproic acid was successfully synthesized by melting polycondensation. The structure, thermal properties, and antistatic ability of the copolymer were characterized by Fourier transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analyses, and ZC36 megohmmeter. Test results show that PEEA is a block copolymer with a melting point of 217°C and a thermal decomposition temperature of 409°C, together with a surface resistivity of 10⁸ Ω/sq. Antistatic poly(acrylonitrile‐co‐butadiene‐co‐styrene) (ABS) materials were prepared by blending different content of PEEA to ABS resin. The antistatic performances, morphology, and mechanical properties were investigated. It is indicated that the surface resistivity of PEEA/ABS blends decrease with the increasing PEEA content, and the excellent antistatic performance is obtained when the antistatic agent is up to 10–15%. The antistatic performance is hardly influenced by water‐washing and relative humidity, and a permanent antistatic performance is available. The antistatic mechanism is investigated. The compatibility of the blends was studied by scanning electron microscopy images. The ladder distribution of antistatic agent is formed, and a rich phase of antistatic agent can be found in the surface layer. The elongations at break of the blend are improved with the increasing antistatic agent; the tensile strength and the notched impact strength kept almost the same. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Phase behavior and morphology in blends of poly(L‐lactic acid) and poly(butylene succinate)

Blends of poly(L ‐lactic acid) (PLA) and poly(butylene succinate) (PBS) were prepared with various compositions by a melt‐mixing method and the phase behavior, miscibility, and morphology were investigated using differential scanning calorimetry, wide‐angle X‐ray diffraction, small‐angle X‐ray scattering techniques, and polarized optical microscopy. The blend system exhibited a single glass transition over the entire composition range and its temperature decreased with an increasing weight fraction of the PBS component, but this depression was not significantly large. The DSC thermograms showed two distinct melting peaks over the entire composition range, indicating that these materials was classified as semicrystalline/semicrystalline blends. A depression of the equilibrium melting point of the PLA component was observed and the interaction parameter between PLA and PBS showed a negative value of ?0.15, which was derived using the Flory–Huggins equation. Small‐angle X‐ray scattering revealed that, in the blend system, the PBS component was expelled out of the interlamellar regions of PLA, which led to a significant decrease of a long‐period, amorphous layer thickness of PLA. For more than a 40% PBS content, significant crystallization‐induced phase separation was observed by polarized optical microscopy. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 647–655, 2002