Preparation,characterization, and adsorption properties of cellulose acetate‐polyaniline membranes

Four lots of cellulose acetate (CA) membranes, modified with polyacrylic acid, using various plasticizers, and coated with polyaniline (PANI) were prepared. The morphology of the membranes was evaluated by using scanning electron microscopy, and the membranes showed larger pore size when the plasticizers were used. The electrical conductivity of the modified membranes and coated with PANI increased by two orders of magnitude when the plasticizer triphenyl phosphate was used. The strain at break improved by an order of magnitude and the glass transition temperature (T_g) showed an average decrease of 36°C when the membranes were plasticized. Finally, these membranes were tested as ion‐exchange materials of a gold‐iodide complex. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Study on volume ratio and plasticizer screening of free coating membranes composed of ethyl cellulose and chitosan

The aim of this study was to optimize the formula of free blended coating membrane of ethyl cellulose (EC) and chitosan (CS), including their suitable ratio range and the best plasticizer used. The dry films were produced by a casting/solvent evaporation method, with different volume ratio of EC and CS solution plasticized by various plasticizers, respectively. The wet films were prepared by immersing dry films in pH 6.8 phosphate buffer saline (PBS) for 24 h. The promising ratio range of EC/CS was below 20/5 or 20/6 with various plasticizer, which was determined by comparing the viscosity of the blended solutions and the morphology of the blended films. The efficiency of plasticization was evaluated by measuring glass transition temperature (T_g). All the testing plasticizers have good compatibility with EC or CS and dibutyl phthalate (DBP) have the strongest efficiency inducing the lowest T_g (39.9°C) of the film. Mechanical properties were evaluated by the ratio of tensile strength (T) to elastic modulus (E). In the wet state, the films with DBP had the highest T/E value (1.2). The results of leaching of plasticizers also verified that DBP was the most stable plasticizer in the films. The release rates of tetramethylpyrazine phosphate (TMPP) through the pellets coated with the blended films of EC/CS (20 : 6 v/v) plasticized by various plasticizers showed that the more water‐soluble the plasticizer was, the more quickly TMPP dissolved from the coated pellets, which further indicated that the water‐insoluble plasticizers (such as DBP) could be more applicable to keep the sustained or controlled release property of the blended films in wet state. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1932–1939, 2006     

Characterization of PVC cable insulation materials and products obtained after removal of additives

Organic solvents cyclohexane, dichloromethane, hexane, and tetrahydrofuran were tested to separate the dioctylphthalate (DOP) as plasticizer from the poly(vinyl chloride) (PVC)‐based materials. It was found that the efficiency of ultrasound‐enhanced hexane extraction of the DOP from PVC is 70% and the efficiency of the separation of the DOP and other compounds from the PVC by dissolution in THF followed by subsequent precipitation was 98–99%. Differential scanning calorimetry (DSC) and thermogravimetry (TG) were used to characterize the thermal behavior of PVC materials before and after extraction of plasticizers. It was found that during heating in the range 20–800°C the total mass loss measured for the nontreated, extracted, and precipitated PVC samples was 71.6, 66.6, and 97%, respectively. In the temperature range 200–340°C, the release of DOP, HCl, and CO₂ was observed by simultaneous thermogravimetry (TG)/FTIR. The effect of plasticizers on thermal behavior of PVC‐based insulation material was characterized by DSC in the range ?40–140°C. It was found that, concerning the PVC cable insulation material before treatment, the value of the glass transition temperature (T_g) was 1.4°C, whereas for the PVC sample extracted by hexane, the value of T_g was 39.5°C and for the PVC dissolved in THF and subsequently precipitated, the value of T_g was 80.4°C. Moreover, the PVC samples after extraction of plasticizers, fillers, and other agents were tested to characterize their thermal degradation. The TG and FTIR results of chemically nontreated, extracted, and precipitated samples were compared. The release of DOP, HCl, CO₂, and benzene was studied during thermal degradation of the samples by FTIR. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 788–795, 2006     

Effect of plasticizer and curing system on freezing resistance of rubbers

At glass transition temperature, T_g the rubber compound becomes stiff and brittle and it loses all its rubbery characteristics. This article deals with the changes in T_g of rubber blends based on natural rubber and polybutadiene rubber of varying vinyl content having different types and content of plasticizers, different curing systems and its effect on physico‐mechanical properties to improve its freezing resistance. The plasticizers used were dioctylphthalate (DOP), tricrecylphosphate (TCP), dioctyladipate (DOA), and oil type plasticizers like parafinic oil (P#2) and aromatic oil (A#2). Among the plasticizers, when DOP and DOA content was high, an appreciable decrease of T_g was found compared to TCP. Moreover, there was a remarkable decrease of T_g using DOA plasticizer, which shows more effective on freezing resistance. However, there was not much change in T_g with oil‐type plasticizers with high oil content compared to TCP plasticizer. The effect of cross‐linking systems such as conventional sulfur vulcanization (CV), efficient sulfur vulcanization (EV), and dicumyl peroxide (DCP) and rubber blends with varying vinyl content in polybutadiene rubber were also carried out. It was found that T_g in different cross‐linking system decreased in this order: CV < EV < DCP. It reveals that DCP cross‐linking system affect more for improving freezing resistance. Physico‐mechanical properties such as tensile strength, tear strength, hardness were also measured. The ratio of initial slope (M₀) to steady‐state slope (M₁), M₀/M₁ in tensile curves of different blends were verified, which in turn related to the physico‐mechanical properties and freezing resistance of rubber compounds. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39795.     

Effects of poly(1,2‐propylene glycol adipate) and nano‐CaCO3 on DOP migration and mechanical properties of flexible PVC

Nano‐CaCO₃ was used as nano‐scale filler and poly(1,2‐propylene glycol adipate) (PPA) was used as polymeric plasticizer in flexible poly(vinyl chloride) (PVC) sheets for the partial replacement of di(2‐ethyl hexyl) phthalate (DOP) in this paper. The effect of PPA and nano‐CaCO₃ on restraining DOP migration was evaluated via extraction tests. The results showed that the introduction of nano‐CaCO₃ can decrease the extraction rate of DOP in the PVC matrix. The tensile strength and elongation at break of CaCO₃‐1/PPA‐20/DOP‐30/PVC were similar to those of DOP‐50/PVC, and CaCO₃‐1/PPA‐20/DOP‐30/PVC exhibited the superior suppression of DOP migration compared with DOP‐50/PVC. Thermogravimetry analysis (TGA) indicated that the addition of nano‐CaCO₃ effectively improved the thermal stability of the nanocomposites. Therefore, the combination of PPA and nano‐CaCO₃ is an effective approach to suppress the migration of DOP. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Alloying of poly(vinyl chloride) to reduce plasticizer migration

Concern over the migration of low molecular weight plasticizer from flexible poly(vinyl chloride) (PVC) used in toys and medical products has spearheaded the commercialization of a number of plasticizing polymers. In this study the plasticizing behavior of an ethylene/vinyl acetate/carbon monoxide terpolymer (Elvaloy® from DuPont) was investigated. Blends of PVC, Elvaloy 742, and dioctyl phthalate (DOP) were processed on a twin‐roll mill and compression molded into plaques. These materials were characterized in terms of their hardness, glass‐transition temperature (T_g), clarity, mechanical properties, and plasticizer migration behavior. The ratios of PVC/DOP/Elvaloy investigated were determined by experimental design. Using this approach it was possible to model the results and produce contour plots to map out the properties of a wide range of formulations. It was confirmed that Elvaloy 742 is compatible with PVC and has a plasticizing effect: this was demonstrated both in terms of a reduction in Shore A hardness and a reduction in T_g. Plasticizer migration was reduced in proportion to the amount of liquid plasticizer replaced. Plasticizing with Elvaloy gave an improvement in tear strength. However, at constant hardness there was no improvement in tensile strength from replacing DOP with Elvaloy. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2022–2031, 2004     

Effect of ketal group in castor oil acid-based plasticizer on the properties of poly(vinyl chloride)

Two castor oil acid esters containing a ketal or ketone group (KCL or CL), as alternative plasticizers for poly(vinyl chloride) (PVC), were prepared. The structures were confirmed by ¹H NMR and FTIR spectroscopies. The effects of the presence of a ketal or ketone group in these compounds on PVC plasticization were examined. The DMA and SEM results showed that both plasticizers were miscible with PVC and exhibited excellent plasticizing properties, compared to those of dioctyl phthalate (DOP). The PVC plasticized by KCL displayed a lower T_g value of 20.6 ° C, which was lower than that of PVC plasticized with DOP (22.3 ° C) and PVC plasticized with CL (40.5 ° C). Tensile tests indicated that PVC plasticized using KCL showed a 37% higher of elongation at break than PVC plasticized by CL and 30% higher than PVC plasticized by DOP. The plasticizing mechanism was also investigated. Moreover, exudation, volatility, and extraction tests, along with TGA indicated that the presence of ketal groups effectively improved the migration resistance of plasticizer and the thermal stability of PVC blends. Taken together, introducing ketal groups into plasticizer might be an effective strategy for improving its plasticizing efficiency.     

Development of renewable resource–based cellulose acetate bioplastic: Effect of process engineering on the performance of cellulosic plastics

This paper deals with the development of a cellulose acetate biopolymer. Plasticization of this biopolymer under varying processing conditions to make it a suitable matrix polymer for bio‐composite applications was studied. In particular, cellulose acetate was plasticized with varying concentrations of an eco‐friendly triethyl citrate (TEC) plasticizer, unlike a conventional, petroleum‐derived phthalate plasticizer. Three types of processing were used to fabricate plasticized cellulose acetate parts: compression molding, extrusion followed by compression molding, and extrusion followed by injection molding. The processing mode affected the physicomechanical and thermal properties of the cellulosic plastic. Compression molded samples exhibited the highest impact strength, tending towards the impact strength of a thermoplastic olefin (TPO), while samples that were extruded and then injection molded exhibited the highest tensile strength and modulus values. Increasing the plasticizer content in the cellulosic plastic formulation improved the impact strength and strain to failure while decreasing the tensile strength and modulus values. The coefficient of thermal expansion (CTE) of the cellulose acetate increased with increasing amounts of plasticizer. Plasticized cellulose acetate was found to be processable at 170–180°C, approximately 50°C below the melting point of neat cellulose acetate.     

Dynamic rheological behavior and microcrystalline structure of dioctyl phthalate plasticized poly(vinyl chloride)

The dynamic rheological behavior of poly(vinyl chloride) (PVC)/dioctyl phthalate (DOP) systems were studied as a function of DOP content and melting temperature. The dynamic rheological behavior of the PVC/DOP systems was found to be remarkably affected by the DOP content. The observed curves of storage modulus (G′) versus frequency were well fitted to an empirical equation (G′ = G′₀ + Kωⁿ, where G′₀ is the low‐frequency yield value of the storage modulus, the exponent n is a dependent index of frequency, K is a constant coefficient, and ω is the angular frequency). The loss tangent and/or phase angle increased remarkably at a higher DOP content. There was an apparent critical DOP content transition where the dynamic rheological behavior of the PVC/DOP systems changed greatly. Scanning electron microscopy observations revealed the existence of a multiscale particle structure in the PVC/DOP systems. For the PVC/DOP (100/70) system, with increasing melting temperature, its dynamic rheological behavior showed an apparent mutation at about 190°C. Differential scanning calorimetry (DSC) analysis confirmed that the high elastic networks in the PVC/DOP systems were closely related to the microcrystalline structure of PVC. The transitions in the curves of the gelation degree and crystallinity versus the DOP content corresponded well to the DOP content transition in the dynamic rheological behavior. DOP could inhibit the secondary crystallite of PVC and almost had no effect on the primary crystallite of PVC. The coexistence of the microcrystalline structure of PVC and the plasticizer (DOP) resulted in high elastic networks in the PVC/DOP systems. The DSC results explained the DOP content transition and the temperature transition in the dynamic rheological behavior of the PVC/DOP systems well. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Recycling of Waste PET: Usage as Secondary Plasticizer for PVC

Postconsumer water bottle poly(ethylene terephthalate) (PET) flakes were depolymerized with ethylene glycol (EG) by the glycolysis reaction in the presence of zinc acetate as the catalyst. In the depolymerization reactions, different weight ratios of PET/EG were used. In order to obtain polyesters used as PVC plasticizers, these glycolysis products containing hydroxyl end groups were reacted with an adipic acid (AA)–containing diacid group at equivalent amounts. In order to obtain PVC plastisols, PVC was dispersed into a plasticizers' mixture composed of di-isooctyl phthalate (DOP) and polyester products by using a high-speed mixer (PVC/plasticizers, 65/35 w/w). For the preparation of plasticizer mixture polyester products were used at a weight ratio of 20%, 40%, 60% of DOP. Plasticized PVC sheets were prepared from plastisols and their glass transition temperatures (T_g), migration, and mechanical properties were determined. The results show that the polyester products obtained from glycolysis products of waste PET can be used as secondary plasticizers, with DOP for PVC.     

ZnO nanocrystallites/cellulose hybrid nanofibers fabricated by electrospinning and solvothermal techniques and their photocatalytic activity

ZnO nanocrystallites have been in situ embedded in cellulose nanofibers by a novel method that combines electrospinning and solvothermal techniques. Zn(OAc)₂/cellulose acetate (CA) precursor hybrid nanofibers with diameter in the range of 160–330 nm were first fabricated via the electrospinning technique using zinc acetate as precursor, CA as the carrier, and dimethylformamide (DMF)/acetone(2 : 1) mixture as cosolvent. The precursor nanofibers were transformed into ZnO/cellulose hybrid fibers by hydrolysis in 0.1 mol/L NaOH aqueous solution. Subsequently, these hybrid fibers were further solvothermally treated in 180°C glycerol oil bath to improve the crystallite structure of the ZnO nanoparticles containing in the nanofibers. The structure and morphology of nanofibers were characterized by scanning electron microscopy, transmission electron microscopy, and X‐ray diffraction. It was found that hexagonal structured ZnO nanocrystallites with the size of ～ 30 nm were dispersed on the nanofiber surfaces and within the nanofibers with diameter of about 80 nm. The photocatalytic property of the ZnO/cellulose hybrid nanofibers toward Rhodamine (RhB) was tested under the irradiation of visible light. As a catalyst, it inherits not only the photocatalytic ability of nano‐ZnO, but also the thermal stability, good mechanical property, and solvent‐resistibility of cellulose nanofibers. The key advantages of this hybrid nanofiber over neat ZnO nanoparticles are its elasticity, dimensional stability, durability, and easy recyclability. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

The effect of plasticizer and cellulose nanowhisker content on the dispersion and properties of cellulose acetate butyrate nanocomposites

We studied the effects of plasticizer and cellulose nanowhisker content on the dispersion and properties of cellulose acetate butyrate (CAB)‐based bionanocomposites. The cellulose nanowhiskers in an aqueous medium were solvent‐exchanged to nonaqueous polar solvent (acetone) and used for nanocomposite processing by solution casting. The plasticized and unplasticized nanocomposites with 5 and 10 wt % cellulose nanowhisker content were prepared. Atomic force microscopy indicated nanoscale dispersion of whiskers in the CAB matrix. The dynamic mechanical analysis showed an increase in storage modulus with addition of cellulose nanowhiskers, especially above the glassy‐rubbery transition region. Thermogravimetric analysis showed an improvement in thermal stability with increased whisker content for both unplasticized and plasticized nanocomposites. The plasticized nanocomposites showed better transparency than the unplasticized composites, indicating a better dispersion of cellulose nanowhiskers in CAB, in the presence of a plasticizer. The dynamic mechanical properties and thermal stability increased, whereas transparency decreased with increased CNW content. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Nanocomposites derived from cellulose acetate and highly branched alkoxysilane

Highly branched alkoxysilane (HB) units were prepared in situ via a Michael‐type reaction between pentaerythrithol triacrylate and aminopropyltriethoxysilane. These units were used as an inorganic component for the modification of cellulose acetate (CA) films using the sol–gel process. The thermal and dynamic‐mechanical behaviors, the morphology, and the dimensional stability of the modified CA films were analyzed. The siloxane‐modified CA films showed thermal stability similar to pure CA, but the residue content at 900°C increased with the addition of HB units. The morphology of these films was characterized by siloxane nanodomains dispersed in the CA matrix, with good interfacial adhesion between the phases. Moreover, the CA/siloxane nanocomposite films showed improved dimensional stability in comparison with CA, i.e., in the presence of HB, the dimensional change was reduced to around 50% of the value observed for pure CA. Finally, a complex dynamic‐mechanical behavior was obtained for the nanocomposite films, as a consequence of the heterogeneous morphology. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation,characterization, and properties of poly(vinyl chloride)/organophilic‐montmorillonite nanocomposites

Poly(vinyl chloride) (PVC)/organophilic‐montmorillonite (OMMT) nanocomposites were prepared by direct melt intercalation. PVC/compatibilizer ((vinyl acetate) copolymer (VAc))/OMMT nanocomposites were also prepared by melt intercalation by a masterbatch process. The effect of OMMT content on the nanostructures and properties of nanocomposites was studied. The nanostructures were studied by wide angle X‐ray diffraction (WAXD) and transmission electron microscopy (TEM). The linear viscoelastic properties and dynamic mechanical properties of PVC/OMMT nanocomposites were also investigated by an advanced rheometric expansion system (ARES) rheometer. The results showed that partially exfoliated and partially intercalated structures coexisted in the PVC/OMMT and PVC/VAc/OMMT nanocomposites. The mechanical properties test results indicated that the notched Charpy impact strengths of nanocomposites were improved compared to that of pristine PVC and had a maximum value at 1 phr OMMT loadings. The compatibilizer could further improve the impact strengths. But the existence of OMMT decreased the thermal stability of PVC/OMMT and PVC/VAc/OMMT nanocomposites. The linear viscoelastic properties test results indicated the dependence of G′ and G″ on ω shows nonterminal behaviors, and they had better processibility compared with pristine PVC. However, the glass transition temperatures of PVC/OMMT nanocomposites almost had little change compared to that of pristine PVC. POLYM. COMPOS., 27:55–64, 2006. © 2005 Society of Plastics Engineers     

Understanding the Compatibility of the Energetic Binder PolyNIMMO with Energetic Plasticizers: Experimental and DFT Studies

The development of energetic binders with suitable energetic plasticizers is required to enhance the mechanical properties and to reduce the glass transition temperature of propellant and explosive formulations. The compatibility of the energetic binder poly(3‐nitratomethyl‐3‐methyloxetane) (polyNIMMO) with five different energetic plasticizers viz. bis(2,2‐dinitro propyl)acetal (BDNPA), dinitro‐diaza‐alkanes (DNDA‐57), 1,2,4‐butanetriol trinitrate (BTTN), N‐N‐butyl‐N ‘(2‐nitroxy‐ethyl) nitramine (BuNENA) and diethyleneglycoldinitrate (DEGDN) was studied by differential scanning calorimetry (DSC), rheology, and DFT methods. The results obtained for the pure binder were compared with the results obtained for the binder/plasticizer blend in regard of the decomposition temperature and the format of the peak indicated the compatibility of polyNIMMO with the plasticizers. The glass transition temperatures of the blends were determined by low temperature DSC and showed desirable lowering of glass transition temperature with single peak. The rheological evaluation revealed that the viscosity of the binder is considerably lowered by means of flow behavior upon addition of 20 % (w/w) plasticizer. The addition of BuNENA and DEGDN has maximum effect on the lowering of viscosity of polyNIMMO. The predicted relative trend of interaction energies between plasticizer and binder is well correlated with the corresponding trend of viscosity of binder/plasticizer blends. These experimental studies verified by theoretical methods are valuable to design practical blends of new plasticizers and binders.     

Application of Azido Esters as Energetic Plasticizers for LOVA Propellant Formulations

The study of a cyclotrimethylene trinitramine‐based low vulnerable ammunition (LOVA) propellant having cellulose acetate (CA) and nitrocellulose (NC) combinations as binders is described herein. Two propellant compositions ( 1 and 2 ) were prepared by replacing the non energetic plasticizer triacetin (TA) with the novel tetraazido ester plasticizers tetraazido malonate and tetraazido glutarate, respectively, and their ballistic, mechanical, and thermal properties were studied. Both compositions 1 and 2 showed thermal stability up to 200 °C with a heat release of 1752.81 and 1774.34 J g⁻¹, respectively. Both compositions have high impact insensitivity (h₅₀: 39 cm), friction insensitivity up to 36 kg, and an ignition temperature greater than 250 °C. The flame temperatures of 1 and 2 are 3164 and 3243 K with linear burn rate coefficients of 0.117 and 0.122 cm s⁻¹ MPa⁻¹, respectively. Similar percentage elongations at three different temperatures (−20 °C, +27 °C, and +55 °C) conditions were recorded for both compositions.     

Experimental and computational investigation of EVOH/clay nanocomposites

Ethylene–vinyl alcohol copolymer (EVOH)/organoclay nanocomposites were prepared via a dynamic melt‐intercalation process. The effect of compatibilizers on the melt blending torque, intercalation level, and morphology of EVOH/organoclay systems was investigated. Maleic anhydride grafted ethylene vinyl acetate (EVA‐g‐ MA), or maleic anhydride grafted linear low‐density polyethylene (LLDPE‐g‐MA), were used to compatibilize EVOH with clay, at various concentrations (1, 5, and 10 wt %). Computer‐simulation techniques are used to predict structural properties and interactions of EVOH with compatibilizers in the presence and absence of clay. The simulation results strongly support the experimental findings and their interpretation. X‐ray diffraction shows enhanced intercalation within the galleries when the compatibilizers were added. Interestingly, results were obtained for the EVOH/clay/compatibilizer systems, owing to a high level of interaction developed in these systems. Thermal analysis shows that, upon increasing the compatibilizer content, lower crystallinity levels result, until at a certain compatibilizer content no crystallization is taking place. Significantly higher mixing viscosity levels were obtained for the EVOH/organoclay blends compared with the neat EVOH polymer. The storage modulus was higher compared with the uncompatibilized EVOH/organoclay blend in the presence of EVA‐g‐MA compatibilizer (at all concentrations), and only at low contents of LLDPE‐g‐MA. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 2060–2066, 2005     

Structure and properties of composites of polyethylene or maleated polyethylene and cellulose or cellulose esters

Composites of linear low‐density poly(ethylene‐co‐butene) (PE) or maleated linear low‐density poly (ethylene‐co‐butene) (M‐PE) and cellulose (CEL), cellulose acetate (CA), cellulose acetate propionate (CAP), or cellulose acetate butyrate (CAB) were prepared in an internal laboratory mixer with 20 wt % polysaccharide. The structure and properties of the composites were studied with tensile testing, dynamic mechanical thermal analysis, differential scanning calorimetry, extraction with a selective solvent, Raman spectroscopy, and X‐ray diffraction. Composites prepared with M‐PE presented yield stress and elongation values higher than those of composites prepared with PE, showing the compatibilizer effect of maleic anhydride. Dynamic mechanical thermal analysis performed for M‐PE–CEL, M‐PE–CA, M‐PE–CAP, and M‐PE–CAB composites showed one glass‐transition temperature (T_g) close to that observed for pure M‐PE, and for M‐PE–CAP, another T_g lower than that measured for the polysaccharide was observed, indicating partial mutual solubility. These findings were confirmed by the extraction of one phase with a selective solvent, gravimetry, and Raman spectroscopy. X‐ray diffraction showed that the addition of CEL, CA, CAP, or CAB had no influence on the lattice constants of PE or M‐PE, but the introduction of the reinforcing material increased the amorphous region. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103:402–411, 2007     

Plasticizers derived from cardanol: synthesis and plasticization properties for polyvinyl chloride(PVC)

Two natural plasticizers derived from cardanol (CD), cardanol acetate (CA) and epoxidized cardanol acetate (ECA), were synthesized and characterized by ¹H NMR and ¹³C NMR. The plasticizing effects of the obtained plasticizers on semi-rigid polyvinylchloride (PVC) formulations were also investigated. Two commercial phthalate ester plasticizers, dioctyl terephthalate (DOTP) and diisononyl phthalate (DINP), were used as controls. Mechanical and thermal properties, compatibility, thermal stability, microstructure, and workability were assessed by dynamic mechanical analysis (DMA), mechanical analysis, thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and dynamic stability analysis, respectively. Results indicated that the natural plasticizer ECA had overallsuperior flexibility, compatibility, thermal stability, and workability comparable to both controls. The obtained CA and ECA have lower volatility resistance and similar extraction and exudation resistance than that of DOTP and DINP. The CA was further blended with DOTP in soft PVC films. Results of DMA, TGA and mechanicalanalysis indicated that CA can serve as a secondary plasticizer to improve the related properties of soft PVC formulations. These CD derived plasticizers show promise as an alternative to fully or partially replace petroleum-based plasticizers.     

Terpolymers. II. Mechanical properties and transition temperatures of terpolymers of vinyl stearate,vinyl acetate,and vinyl chloride

Vinyl stearate was studied as a major internal plasticizer in terpolymers containing vinyl acetate and vinyl chloride. The terpolymers were prepared by systematically replacing vinyl acetate by close increments of vinyl stearate starting with combinations of vinyl acetate and vinyl chloride, in increments, over all compositions. For comparison of properties, a complete range of copolymers of vinyl stearate and vinyl chloride, as well as mixtures of poly(vinyl chloride) and di-2-ethylhexyl phthalate (DOP) were also made. The external plasticizer was more efficient in reducing the glass temperature than was vinyl stearate. The decline in T_g with weight fraction of plasticizer was linear for the copolymers and terpolymers but concave downward with the liquid diluent. The linear decline was shown to involve mere additivity of the free volume contributed by each side-chain methylene (or methyl) group in both vinyl esters to reducing T_g. The mechanism of the diluent system was more complex. However, the magnitude of the reduction of tensile modulus at a given weight fraction of DOP could be equaled or exceeded by the same amount of vinyl stearate, by increasing the vinyl acetate content of the base copolymer to 40 mole-% or more. Unfortunately, the ultimate strengths and elongations of internally plasticized systems were reduced more than those of the mixtures at comparable compositions. Vinyl stearate was found to markedly retard photolytic degradation compared to both vinyl acetate and the external plasticizer in unstabilized samples having nearly the same thermal treatment. The effect was greater than could be ascribed to dilution by the long alkyl group. The production of a stearoyl radical more stable than the radicals initiating dehydrochlorination is suggested as a possible mechanism.