Synthesis and characterization of novel polyureas based on benzimidazoline‐2‐one and benzimidazoline‐2‐thione hard segments

Six novel polyureas were prepared from benzimidazolin‐2‐one and benzimidazolin‐2‐thione, which acted as hard segments, with two aromatic diisocyanates (4,4′‐diphenylmethane diisocyanate and toluene 2,4‐diisocyanate) and one aliphatic diisocyanate (hexamethylene diisocyanate). The polymers that formed were fully characterized with Fourier transform infrared spectroscopy, ¹³C‐NMR cross‐polarization/magic‐angle spinning, differential scanning calorimetry, and thermogravimetry. X‐ray diffraction revealed that the polymers contained crystalline and amorphous regions that varied with the nature of the backbone structures. All the polyureas were insoluble in common organic solvents, and this made it difficult to investigate their solution properties. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 576–583, 2006     

Preparation, electrochemical characterization and charge–discharge of reticulated vitreous carbon/polyaniline composite electrodes

Polyaniline was electrodeposited onto reticulated vitreous carbon – RVC – in order to obtain a tridimensional composite electrode. Three variations of these electrodes were analysed: a small-anion-doped polyaniline (RVC/Pani), a polyanion-doped polyaniline (RVC/PaniPSS) and a bi-layer type formed by an inner layer of the first electrode and an outer layer of the second one (RVC/Pani/PaniPSS). These composites were characterized by cyclic voltammetry, scanning electronic microscopy and electrochemical impedance spectroscopy. Photomicrographies, voltammetric profiles and impedance data pointed to different morphological and electrochemical characteristics for polyaniline doped with small or large anions, and a mixed behavior for the bi-layer electrodes. Charge–discharge tests for these tridimensional (3D) electrodes, employed as the cathode in lithium batteries, indicated better performance for the RVC/Pani electrode. These RVC composites presented higher specific capacities when compared with those obtained for Pani deposited onto bidimensional substrates.     

Synthesis and characterization of novel polyurethanes based on 1,3‐bis(hydroxymethyl) benzimidazolin‐2‐one and 1,3‐bis(hydroxymethyl) benzimidazolin‐2‐thione hard segments

Novel polyurethanes (PUs) based on 1,3‐bis(hydroxymethyl) benzimidazolin‐2‐one and 1,3‐bis(hydroxymethyl) benzimidazolin‐2‐thione as hard segments with two aromatic diisocyanates, viz., 4,4′‐diphenylmethane diisocyanate and toluene 2,4‐diisocyanate, were prepared. Polymer structures were established by Fourier transform infrared and nuclear magnetic resonance spectroscopy. Morphology of the PUs was studied by differential scanning calorimetry and thermogravimetry. All PUs contain domains of crystalline and amorphous structures as indicated by X‐ray diffraction experiments. Furthermore, polymers were insoluble in the majority of organic solvents and, hence, their solution characterization was not possible. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2236–2244, 2005     

Mechanochemical synthesis and characterization of poly(2,5‐dimethoxy aniline) salts

The interfacial interaction and orientation of molecules during the polymerization process plays a vital role in the enhancement of the surface properties of conducting polymers. In this perspective, a solid‐phase mechanochemical route is employed to prepare poly(2,5‐dimethoxy aniline) (PDMA) and its salts with superior properties. Various studies performed on the as‐prepared polymer highlights the formation of polymeric particles with excellent physicochemical properties. Elemental analysis showed the presence of dopants anion in the polymeric backbone. Spectroscopic profile of PDMAs revealed the formation of emeraldine form of PDMAs. Moreover, these studies indicate the formation of PDMA‐HCl in a highly doped state. The surface morphological pictures of PDMAs revealed the formation of aggregated microstructured to nanostructured particulates. X‐ray diffraction, cyclic voltammetry were used to evaluate the physicochemical properties of PDMAs. PDMA salts exhibited crystalline behavior and good electrochemical activity. TG/DTA analysis showed that all the PDMAs were thermally stable up to 240°C. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Water‐dispersible conducting polyaniline/nano‐SiO2 composites without any stabilizer

A water‐dispersible conducting polyaniline/ nano‐SiO₂ composite, with a conductivity of 0.071 S cm^?1 at 25°C, was prepared by the oxidative polymerization of aniline in the presence of amorphous nano‐SiO₂ particles. And the structure, morphology, thermal stability, conductivity, and electroactivity of this composite were also investigated. This composite has been steadily dispersed in the aqueous solution for about 10–36 h without the need for any stabilizer. It would significantly impulse the commercial applications of conducting polyaniline/nano‐SiO₂ composite as fillers for antistatic and anticorrosion coatings. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Solid‐state characterization and the thermal properties of stereoregular poly(vinyl chloride) prepared by urea clathrate polymerization

The solid‐state characterization of highly stereoregular poly(vinyl chloride) (PVC) prepared by urea clathrate polymerization was carried out by using various instrumental analyses. The structural differences of PVC appeared most remarkably in solubility to organic solvents, IR, WAXD, and solid‐state ¹³C‐NMR spectra. The value of the glass transition temperature (T_g) was about 90°C, not as high as expected, although its detection was quite difficult. The thermal stability was poor, as evidenced by the easy discoloration of this polymer by heat treatment, which was related to the absence of a termination reaction. Dynamic ESR spectra in the solid state clearly indicate that the radical formation occurs at such a low temperature as 160°C in the initial degradation stage. The degradation characteristics of urea clathrate PVC were critically discussed. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2820–2825, 1999     

Solid‐state polymerization and characterization of a copolyamide based on adipic acid, 1,4‐butanediamine,and 2,5‐furandicarboxylic acid

2,5‐Furandicarboxylic acid (FDCA) is a promising biobased alternative material to terephthalic acid. In this study, three types of poly(butylene adipamide) (PA‐4,6) containing 10, 20, and 30 mol % of poly(butylene‐2,5‐furandicarboxylamide) (PA‐4,F) were synthesized through consecutive prepolymerization and solid‐state polymerization (SSP). The incorporation of a 10 mol % PA‐4,F component into PA‐4,6 resulted in slight increases in the intrinsic viscosity (IV) and glass‐transition temperature (T_g) after 12 h of SSP at 220 °C. When the SSP temperature and reaction time increased, IV increased proportionally. The highest IV value of 0.75 was obtained by 48 h of SSP at 240 °C, whereas increases in the PA‐4,F content to 20 and 30 mol % gave rise to decreases in IV, T_g, and melting temperature; this interrupted the increase in SSP temperature. The thermal decomposition temperature of the PA‐4,F‐incorporated polyamide was lower than that with PA‐4,6 because of the lower thermal stability of the FDCA component. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43391.     

Solid‐state polymerization of poly(trimethylene terephthalate)

The solid‐state polymerization (SSP) of poly(trimethylene terephthalate) (PTT) has been studied and compared with that of poly(ethylene terephthalate) (PET). Because PTT and PET share the same SSP mechanism, the modified second‐order kinetic model, which has successfully been used to describe the SSP behaviors of PET, also fits the SSP data of PTT prepolymers with intrinsic viscosities (IVs) ranging from 0.445 to 0.660 dL/g. According to this model, the overall SSP rate is ?dC/dt = 2k_a(C ? C_ai)², where C is the total end group concentration, t is the SSP time, k_a is the apparent reaction rate constant, and C_ai is the apparent inactive end group concentration. With this equation, the effects of all factors that influence the SSP rate are implicitly and conveniently incorporated into two parameters, k_a and C_ai. k_a increases, whereas C_ai decreases, with increasing SSP temperature, increasing prepolymer IV, and decreasing pellet size, just as for the SSP of PET. Therefore, the SSP rate increases with increasing prepolymer IV and increasing SSP temperature. The apparent activation energy is about 26 kcal/mol, and the average SSP rate about doubles with each 10°C increase in temperature within the temperature range of 200–225°C. The SSP rate increases by about 30% when the pellet size is decreased from 0.025 to 0.015 g/pellet. Compared with PET, PTT has a much lower sticking tendency and a much higher SSP rate (more than twice as high). Therefore, the SSP process for PTT can be made much simpler and more efficient than that for PET. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3188–3200, 2003     

New amphiphilic sulfonic acid dopant‐cum‐templates for diverse conducting polyaniline nanomaterials

We report new structurally identical polar head amphiphilic sulfonic acids as molecular templates to study the role of the polymerization routes on the solid state properties of polyaniline nanomaterials. Three long chain substituted phenols such as 3‐pentadecylphenol, renewable resource‐cardanol, and nonyl phenol are reacted with sultones to make new long tail amphiphiles. The amphiphilic molecules self‐organized as 4–6 nm tiny micelles in water which were employed as templates for polymerization. Emulsion, dispersion, and interfacial polymerization of aniline along with these new amphiphiles produced well‐defined polyaniline nanofibers, nanotapes, and nanospheres. Electron microscopic analysis revealed that the dopant structure and polymerization routes determine the morphology of the polyaniline nanomaterials. Absorbance studies revealed that the samples produced via interfacial route showed expanded polymer chain conformation as a result of unidirectional growth of the chains in the aqueous‐organic interface. Emulsion and dispersion route samples were produced in coil‐like chain conformation. Powder X‐ray analysis confirmed that the expanded conformation in the polyaniline backbone enhances the high solid state ordering, high percent crystallinity, and larger crystallite size compared to that of the samples with coil‐like conformation. Highly ordered interfacial route samples showed conductivity three orders of magnitude higher than that of the weakly packed polyaniline nanomaterials. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Solid‐state polymerization of poly(ethylene 2,6‐naphthalate)

The solid‐state polymerization (SSP) of poly (ethylene 2,6‐naphthalate) (PEN) was studied and compared with that of poly(ethylene terephthalate) (PET). The SSP of PEN, like that of PET, could be satisfactorily described with a modified second‐order kinetic model, which was based on the assumptions that part of the end groups were inactive during SSP and that the overall SSP followed second‐order kinetics with respect to the active end‐group concentration. The proposed rate equation fit the data of the SSP of PEN quite well under various conditions. PEN prepolymers in pellet and cube forms with intrinsic viscosities (IVs) ranging from 0.375 to 0.515 dL/g, various particle sizes, and various carboxyl concentrations were solid‐state polymerized at temperatures ranging from 240 to 260°C to study the effects of various factors. The SSP data obtained in this study could be readily applied to the design of commercial PEN SSP processes. Because PEN and PET share the same SSP mechanism, in general, the SSP behaviors of PEN are similar to those of PET. Thus, the SSP rate of PEN increased with increasing temperature, increasing prepolymer IV, and decreasing prepolymer particle size. However, because of the much higher barrier properties of PEN, the prepolymer particle size and carboxyl concentration had much greater effects on the SSP of PEN than on the SSP of PET. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1075–1084, 2007     

Preparation and characterization of bipolar membranes modified using photocatalyst nano‐TiO2 and nano‐ZnO

The nano‐ZnO and nano‐TiO₂ were added into chitosan (CS) anion layer to prepare polyvinyl alcohol (PVA) ‐ sodium alginate (SA)/ TiO₂‐ZnO‐CS (here, PVA:polyvinyl alcohol; SA:sodium alginate) bipolar membrane (BPM), which was characterized using scanning electron microscopy, atomic force microscopy (AFM), thermogravimetric analysis (TG), electric universal testing machine, contact angle measurer, and so on. Experimental results showed that nano‐TiO₂‐ZnO exhibited better photocatalytic property for water splitting at the interlayer of BPM than nano‐TiO₂ or nano‐ZnO. The membrane impedance and voltage drop (IR drop) of the BPM were obviously decreased under the irradiation of high‐pressure mercury lamps. At a current density of 60 mA/cm², the cell voltage of PVA‐SA/TiO₂‐ZnO‐CS BPM‐equipped cell decreased by 1.0 V. And the cell voltages of PVA‐SA/TiO₂‐CS BPM‐equipped cell and PVA‐SA/ZnO‐CS BPM‐equipped cell were only reduced by 0.7 and 0.6 V, respectively. Furthermore, the hydrophilicity, thermal stability, and mechanical properties of the modified BPM were increased. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Solid‐state carbon‐13 NMR study of material composites based on sugarcane bagasse and thermoplastics polymers

The composites formed by sugarcane bagasse and thermoplastic polymers, such as polypropylene (PP), polyethylene (PE), and ethylene‐co‐vinyl acetate (EVA), have been analysed by carbon‐13 high‐resolution solid‐state nuclear magnetic resonance (NMR), employing crosspolarization magic angle spinning (CPMAS); variable contact‐time experiment and proton spin‐lattice relaxation time in the rotating frame. NMR responses showed that these techniques can be used to observe the degree of compatibility and homogeneity of different polymers composites. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2150–2154, 2001     

Solid‐state NMR characterization of cyclomaltoheptaose (β‐cyclodextrin) polymers using high‐resolution magic angle spinning with gradients

Solid‐state nuclear magnetic resonance (NMR) techniques were used to characterize cyclomaltoheptaose (β‐cyclodextrin, β‐CD) polymers. These insoluble materials have been investigated by cross‐polarization magic angle spinning with dipolar decoupling (CP/MAS), magic angle spinning without dipolar decoupling (MAS), and high‐resolution magic angle spinning with gradients (HRMAS). These NMR spectra allow the assignment of the principal ¹H and ¹³C signals. The presence of two distinct components (cross‐linked β‐CD and polymerized epichlorohydrin) in the materials was clearly demonstrated. These polymers were used as sorbents and the resulting NMR spectra are presented and discussed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1288–1295, 2000     

A study on the preparation of polymer/montmorillonite nano‐composite materials by photo‐polymerization

The preparation of polymer/montmorillonite intercalation composite materials was studied by two kinds of photo‐polymerization reaction (photo‐acid generation and photo‐radical generation). Small‐angle X‐ray diffraction was used for the structural characterization of montmorillonite contained in the products. Results indicated that, after chemical modification of montmorillonite, the monomer (methyl methacrylate) and the prepolymer (m‐cresol/HMMM) were able to intercalate into the layers of clay and to polymerize ‘in situ’, thus producing photo‐polymerized composite materials. The advantages and shortcomings of the method of photo‐polymerization for the preparation of these composite materials are discussed. © 2001 Society of Chemical Industry     

Synthesis,physical properties,and characterization of starch‐based blend films by adding nano‐sized TiO2/poly(methyl metacrylate‐co‐acrylamide)

The purpose of this study was to improve the physical properties and to expand the application range of starch‐based blend films added nano‐sized TiO₂/poly(methyl methacrylate‐co‐acrylamide) (PMMA‐co‐AM). Starch‐based blend films were prepared by using corn starch, polyvinyl alcohol (PVA), nano‐sized PMMA‐co‐AM, nano‐sized TiO₂/PMMA‐co‐AM particles, and additives, i.e., glycerol (GL) and citric acid (CA). Nano‐sized PMMA‐co‐AM was synthesized by emulsion polymerization and TiO₂ nanoparticles were also prepared by using sol–gel method. Nano‐sized TiO₂/PMMA‐co‐AM particles were synthesized by wet milling for 48 h. The morphology and crystallinity of TiO₂, nano‐sized PMMA‐co‐AM and TiO₂/PMMA‐co‐AM particles were investigated by using the scanning electron microscope (SEM) and X‐ray diffractometer (XRD). In addition, the functional groups of the TiO₂/PMMA‐co‐AM particles were characterized by IR spectrophotometry (FTIR). The physical properties such as tensile strength (TS), elongation at break (%E), degree of swelling (DS), and solubility (S) of starch‐based films were evaluated. It was found that the adding of nano‐sized particles can greatly improve the physical properties of the prepared films. The photocatalytic degradability of starch/PVA/nano‐sized TiO₂/PMMA‐co‐AM composite films was evaluated using methylene blue (MB) and acetaldehyde (ATA) as photodegradation target under UV and visible light. The degree of decomposition (C/C₀) of MB and ATA for the films containing TiO₂ and CA was 0.506 and 0.088 under UV light irradiation and 0.586 (MB) and 0.631 (ATA) under visible light irradiation, respectively. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Solid‐state foaming of carbon fiber/polypropylene/nano‐CACO3 composite using supercritical CO2

In this work, nano‐CaCO₃ was used to improve the foamability of carbon fiber (CF)/polypropylene (PP) composite in solid‐state foaming using supercritical CO₂. The CF content was maintained at 15 wt% and four concentrations of nano‐CaCO₃ content, 1, 3, 5 and 8phr, were used. The surface of nano‐CaCO₃ was firstly treated by silane coupling agent. By the way, the properties of the nano‐composites with various nano‐CaCO₃ contents were analyzed by scanning electron microscope (SEM), differential scanning calorimeter (DSC), and torque rheometer. Before foaming, the gas absorption experiment was done using gravimetric method. Concerning on determination of the foaming conditions, it is found that 175°C and 60s were suitable as foaming temperature and time. Furthermore, we can also find that the foamed composites with 3phr nano‐CaCO₃ showed the smallest mean cell diameter and largest cell density compared with the other nano‐CaCO₃ contents under the given saturation condition. In addition, the mean cell diameter decreased while cell density increased as saturation pressure increased because of the higher gas solubility in the composites. When the saturation pressure was 25MPa, the mean cell diameter and cell density with 3phr nano‐CaCO₃ were 17μm and 2.20×10⁷cells/cm³, respectively. POLYM. COMPOS., 35:1723–1735, 2014. © 2013 Society of Plastics Engineers     

Solid‐state dye‐sensitized and bulk heterojunction solar cells using TiO2 and ZnO nanostructures: recent progress and new concepts at the borderline

In the field of photovoltaic energy conversion, hybrid inorganic/organic devices represent promising alternatives to standard photovoltaic systems in terms of exploiting the specific features of both organic semiconductors and inorganic nanomaterials. Two main categories of hybrid solar cells coexist today, both of which make much use of metal oxide nanostructures based on titanium dioxide (TiO₂) and zinc oxide (ZnO) as electron transporters. These metal oxides are cheap to synthesise, are non‐toxic, are biocompatible and have suitable charge transport properties, all these features being necessary to demonstrate highly efficient solar cells at low cost. Historically, the first hybrid approach developed was the dye‐sensitized solar cell (DSSC) concept based on a nanostructured porous metal oxide electrode sensitized by a molecular dye. In particular, solid‐state hybrid DSSCs, which reduce the complexity of cell assembly, demonstrate very promising performance today. The second hybrid approach exploits the bulk heterojunction (BHJ) concept, where conjugated polymer/metal oxide interfaces are used to generate photocurrent. In this context, we review the recent progress and new concepts in the field of hybrid solid‐state DSSC and BHJ solar cells based on TiO₂ and ZnO nanostructures, incorporating dyes and conjugated polymers. We point out the specificities in common hybrid device structures and give an overview on new concepts, which couple and exploit the main advantages of both DSSC and BHJ approaches. In particular, we show that there is a trend of convergence between both DSSC and BHJ approaches into mixed concepts at the borderline which may allow in the near future the development of hybrid devices for competitive photovoltaic energy conversion. Copyright © 2011 Society of Chemical Industry     

Solid‐state polymerization of bisphenol A polycarbonate with a spray‐crystallizing method

A novel crystallization method for the production of high‐molecular‐weight bisphenol A polycarbonate by solid‐state polymerization is suggested. In this method, a low‐molecular‐weight polycarbonate prepolymer is dissolved in a solvent and then partially crystallized with a novel spray‐crystallizing method to prepare crystallized polycarbonate particles having a very uniform and porous structure with a narrow melting region. As a result, during solid‐state polymerization, the phenol byproduct can be easily removed from the polymerizing porous polycarbonate particles, and the polymerization rate is dramatically increased. In particular, the effects of the crystallization methods on secondary crystallization during solid‐state polymerization and the melting behavior have been investigated with differential scanning calorimetry studies. The final product, a high‐molecular‐weight polycarbonate, displays a very narrow molecular weight distribution and uniform physical properties. A simultaneous process and an adequate reactor design for spray crystallization and solid‐state polymerization are also suggested. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Nonisothermal crystallization kinetics of flame‐sprayed polyamide 1010/nano‐ZrO2 composite coatings

Polyamide1010 (PA1010) and its composite with nanometer‐sized zirconia (PA1010/nano‐ZrO₂) coatings were deposited using a flame spray process. The kinetics of nonisothermal crystallization of PA1010/nano‐ZrO₂ composite coatings was investigated by differential scanning calorimetry (DSC) at various cooling rates. Several different analysis methods were used to describe the process of nonisothermal crystallization. The results showed that the modified Avrami equation and Mo's treatment could describe the nonisothermal crystallization of the composite coatings very well. The nano‐ZrO₂ particles have a remarkable heterogeneous nucleation effect in the PA1010 matrix. The values of halftime and Z_c showed that the crystallization rate increased with increasing cooling rates for both PA1010 and PA1010/nano‐ZrO₂ composite coating, but the crystallization rate of PA1010/nano‐ZrO₂ composite coating was faster than that of PA1010 at given cooling rate. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Solid‐state 13C‐NMR and study of the subproducts obtained from corn industry

The two types of commercial corn flour subproducts from the Brazilian corn industry containing starch with low fat and with fat were investigated by solid‐state NMR techniques to improve their uses. From the NMR techniques used, it was characterized that after a treatment the quantity of fibers decreased. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1680–1685, 2002; DOI 10.1002/app.10547