NaGd(WO4)2:Yb3+/Tm3+反蛋白石光子晶体的制备与上转换发光调制研究

三维光子晶体具有长程有序的结构特点, 在可见和近红外光谱范围内有着广泛的应用。光子晶体的一个重要性质是其对嵌入其中的发光中心自发辐射具有调制作用。本研究利用自组装和模板辅助法制备高质量的三维NaGd(WO₄)₂:Yb³⁺/Tm³⁺反蛋白石光子晶体, 探究了光子带隙对Tm³⁺离子上转换荧光发射与发光动力学的调制作用。通过对比分析发现, 由于反蛋白石光子晶体独特的周期性大孔结构和光子带隙效应, 处于光子带隙内的Tm³⁺离子¹G₄-³H₆的发光强度被抑制约45%, 自发辐射速率(SDR)被抑制约30%, 同时上转换局域热效应得到有效的调制。本实验结果对探索新型高效稀土掺杂上转换发光材料和提高上转换发光效率有指导意义。     

活性炭模板法制备锡酸锌掺杂磷化合物及表征

选用磷酸活化后的活性炭为模板,NaSnO₃·3H₂O、ZnSO₄·7H₂O为原料,通过生物质模板法制备了锡酸锌掺杂磷(Zn₂SnO₄/P)化合物。通过X射线粉末衍射(XRD)、扫描电子显微镜(SEM)和N_2吸脱附等温线对制备的Zn₂SnO₄/P的结构、形貌进行表征。结果表明:Zn₂SnO₄/P为尖晶石结构,其形貌基本上和活性炭相匹配。其比表面积、孔体积和平均孔径分别为87m²/g、0.20cm³/g和9.0nm。     

Er3+掺杂TiO2空心球的制备及其光催化性能研究

以钛酸四丁酯、氧化铒、硝酸等为原料, 采用碳球模板法制备了TiO₂: Er³⁺空心球材料, 利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线衍射(XRD)等测试方法, 对样品的结构和形貌进行了表征。并利用紫外-可见(UV-Vis)分光光度计考察了TiO₂: Er³⁺空心球材料在催化染料罗丹明B、亚甲基蓝、茜素红、甲基橙的脱色降解过程中的应用性能。系统研究了Er³⁺掺杂浓度、不同离子型染料和染料水溶液的pH等因素对催化降解效率的影响。实验结果表明: 经600℃煅烧3 h制备的TiO₂: Er³⁺为锐钛矿晶型, 空心球结构, 尺寸均匀, 粒径约为120 nm, 比表面积约为60.5 m²/g; Er³⁺掺杂量为0.5mol%的样品对甲基橙染料的催化降解效率最高; 对四种不同离子型染料, 茜素红的催化降解效果显著, 在紫外光照射下, 催化效率较未掺杂Er³⁺的TiO₂提高了约30%。     

Properties of Al heavy-doped ZnO thin films by RF magnetron sputtering

Al-doped ZnO films were deposited by RF magnetron sputtering. From the X-ray diffraction and scanning electron spectrometer studies, wurtzite structure with (0 0 2) orientation ZnO thin films were obtained at Al concentration below 15 atomic percent (at.%). As the Al concentration above 15 at.%, the thin films did not fully crystallize. Two new emission peaks occurred at 351 nm and 313 nm when the Al doping above 15 at.% from the photoluminescence spectrum, and the peaks shift towards the shorter wavelengths with increasing the Al concentration. X-ray photonic spectra of O 1s conformed the amount of oxygen captured by Al³⁺ increasing as the Al³⁺ concentration increasing due to the dominant Al³⁺ possess high charge in competition with Zn²⁺ in the matrix of ZnO.     

Honeycomb-like graphitic ordered macroporous carbon prepared by pyrolysis of ammonium bicarbonate

Honeycomb-like graphitic macroporous carbon (HGMC) was synthesized by means of pyrolysis of NH₄HCO₃ using Mg powder as reductant in an autoclave at 550 °C. The characterization of structure and morphology was carried out by X-ray diffraction (XRD), Raman spectrum, field-emission scanning electron microscopy (FESEM), and (High-resolution) transmission electron microscope [(HR)TEM]. The results of nitrogen adsorption-desorption indicate that the products are macropore materials with the pore size of 1-3 μm, and the Brunauer-Emett-Teller (BET) surface area was 14 m²/g. As a typical morphology, the possible growth process of HGMC was also investigated and discussed. The experimental results show that the in situ formed MgO microparticles play a template role during the HGMC formation.     

Zn2+掺杂诱导Eu3+激活BiOCl层状半导体的反常发光性能研究

采用固相法在500℃下成功制备Zn²⁺掺杂BiOCl:Eu³⁺层状半导体, 并研究了Zn²⁺ (0~20mol%)掺杂对Eu³⁺激活BiOCl层状半导体发光性能的影响。利用X射线衍射(XRD)、X射线光电子能谱(XPS)、扫描电镜(SEM)、傅里叶变换红外光谱(FT-IR)、激发-发射光谱、荧光寿命衰减曲线对样品的结构和性能进行表征。研究发现, 随Zn²⁺掺杂浓度增大, BiOCl晶体结构不变, Eu³⁺荧光寿命延长, 但发光强度却出现先减后增的反常现象。综合分析表明这可能与BiOCl特殊的层状结构有关。通过XRD和XPS的表征可以推断: 当Zn²⁺掺杂浓度≤10mol%, Zn²⁺在BiOCl中掺杂方式以晶胞层间隙掺杂为主; 当Zn²⁺掺杂浓度>10mol%后, 掺杂方式逐渐向取代掺杂转变。两种掺杂机制对Eu³⁺荧光寿命的改变以及形成缺陷对基质能量传递效率的影响可能是形成上述反常现象的主要原因。研究结果有助于认识稀土掺杂层状半导体的发光性能及影响规律, 并对Eu³⁺掺杂BiOCl这类新型发光材料的开发设计具有指导意义。     

Template-mediated strategy to regulate hierarchically nitrogen--sulfur co-doped porous carbon as superior anode material for lithium capacity

Considering its rapid lithiation/delithiation process and robust capacitive energy storage, hierarchical porous carbon is regarded as a promising candidate for lithium-ion batteries (LIBs). However, it remains a great challenge to construct a porous structure and prevent structure stacking for carbon-based materials. Herein, a template-mediated approach is developed to synthesize hierarchical nitrogen–sulfur co-doped porous carbon (NSPC) using low-cost asphalt precursors. The strategy for synthesis uses g-C₃N₄ and NaHCO₃ as gaseous templates and NaCl as a solid template, which causes the formation of hierarchical porous carbon with a high specific surface area. The resultant porous structure and nitrogen-doping process can prevent the aggregation of nanosheets, maintain the structural stability upon cycling, and achieve rate-capable lithium storage. Serving as a LIBs anode, reversible specific capacities of the NSPC24 electrode reach 788 and 280 mAh·g^–1 at 0.1 and 1 A·g^–1, respectively. Furthermore, its specific capacity remains at 830 mAh·g^–1 after 115 cycles at 0.1 A·g^–1. Even after 500 cycles, high specific capacities of 727 mAh·g^–1 at 0.5 A·g^–1 and 624 mAh·g^–1 at 1 A·g^–1 are achieved, demonstrating excellent cycling performance. The gas–solid bifunctional template-mediated approach can guide the design of porous materials very well, meanwhile realizing the high value-added utilization of asphalt.     

Preparation of irregular mesoporous hydroxyapatite

An irregular mesoporous hydroxyapatite (meso-HA), Ca₁₀(PO₄)₆(OH)₂, is successfully prepared from Ca(NO₃)₂·4H₂O and NH₄H₂PO₄ using surfactant cetyltrimethyl ammonium bromide (CTAB) as template. Fourier transform infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC) results reveal that the positive head of CTAB is assembled on the surface precipitated HA and much NH₄⁺ is enclosed in precipitated HA before calcination. Field scanning electron microscope (FSEM) reveals that there exist many interconnected pores throughout the HA reticular skeleton. Nitrogen adsorption–desorption experiment exhibits a mesoporous material type IV curve, and pore size distribution calculated from the desorption branch of the isotherms based on Barrett–Joyner–Halenda (BJH) model shows that most pores throughout the HA reticular skeleton are sized at about 40 nm, but the pores are not uniform on the whole, owning to decomposition of the “organic” CTAB templating structures and ammonium salt enclosed in the precipitated HA. The specific surface area of irregular meso-HA is calculated to be 37.6 m²/g according to the Brunauer–Emmett–Teller (BET) equation. Moreover, after polylactic acid/meso-HA (PLA/meso-HA) composites degraded 12 weeks in normal saline at 37 °C, the interconnected pores throughout the HA skeleton were enlarged and sized in micron degree, which resemble trabecular bone structure very much.     

Fabrication of β-Si3N4 whiskers by combustion synthesis with MgSiN2 as additives

β-Si₃N₄ whiskers with diameter of 0.5–2 μm and aspect ratio of 10–15 have been successfully prepared by combustion synthesis under 30–50 atm nitrogen pressure. The addition of MgSiN₂ powder plays a significant role in the growth of β-Si₃N₄ whiskers. The as-prepared products were characterized by X-ray powder diffraction (XRD) and scanning electron microscopy (SEM).     

Crystal structure and spectroscopic studies of NaGd(PO3)4

Single crystals of gadolinium–sodium polyphosphate NaGd(PO₃)₄ were grown for the first time using a flux method and characterized by X-ray diffraction. This phosphate crystallizes in a monoclinic system with P2₁/n space group and with the following unit-cell dimensions: a = 9.767(3) Å, b = 13.017(1) Å, c = 7.160(2) Å, β = 90.564(5)°, V = 910.3(4) Å³ and Z = 4. The crystal structure was solved from 3451 X-ray independent reflections with final R(F²) = 0.0219 and R_w(F²) = 0.056 refined with 164 parameters (). The atomic arrangement can be described as a long chain polyphosphate organization. Two infinite (PO₃)∝ chains with a period of eight tetrahedra run along the [0 1 1] direction. The structure of NaGd(PO₃)₄ consists of GdO₈ polyhedra sharing oxygen atoms with phosphoric group PO₄. Each Na⁺ ion is bonded to eight oxygen atoms.     

Sol–gel synthesis and luminescence of unexpected microrod crystalline Ca5La5(SiO4)3(PO4)3O2:Dy phosphors employing different silicate sources

Ca₅La₅(SiO₄)₃(PO₄)₃O₂ doped with Dy³⁺ were synthesized by sol–gel technology with hybrid precursor employed four different silicate sources, 3-aminopropyl-trimethoxysilane (APMS), 3-aminopropyl-triethoxysilane (APES), 3-aminopropyl-methyl-diethoxysilane (APMES) and tetraethoxysilane (TEOS), respectively. The SEM diagraphs show that there exist some novel unexpected morphological structures of microrod owing to the crosslinking reagents than TEOS as silicate source for their amphipathy template effect. X-ray pictures confirm that Ca₅La₅(SiO₄)₃(PO₄)₃O₂:Dy³⁺ compound is formed by a pure apatitic phase. The Dy³⁺ ions could emit white light in Ca₅La₅(SiO₄)₃(PO₄)₃O₂ compound, and the ratio of Y/B is 1.1, when the Dy³⁺ doped concentration is 1.0 mol%.     

氮/硫共掺杂对纤水镁石模板碳纳米管电化学性能的影响

以天然矿物纤水镁石为模板、蔗糖为碳源制备多孔碳纳米管, 并以硫脲为氮、硫源, 采用水热法制备氮/硫共掺杂的碳纳米管。结果表明, 掺杂碳纳米管继承了纤水镁石模板的柱状结构, 呈现中空管状, 增大了模板炭的比表面积和孔容。在6 mol·L^-1 KOH电解液中, 电流密度为1 A·g^-1时, 未掺杂碳纳米管的比电容为62.2 F·g^-1, 氮掺杂之后碳纳米管的比电容为97.0 F·g^-1, 氮/硫共掺杂的碳纳米管比电容为172.0 F·g^-1, 氮/硫共掺杂后碳纳米管的电化学性能比未掺杂的提高近3倍; 循环1000次电容保持率达89%, 说明掺/硫共掺杂碳纳米管具有良好的电化学性能。此外, 组装的对称型超级电容器同样展示了良好的电容性能。     

一步水热法制备纳米SnO2@C复合材料及其储锂性能研究

以两种糖类化合物(葡萄糖与水溶性淀粉)为碳源，以SnCl₄.5H₂O为锡源用一步水热法制备了SnO₂@C复合物。使用X射线衍射(XRD)、傅里叶变换红外光谱(FTIR)、N₂吸脱附法和透射电镜(TEM)表征其组成和微观结构，并采用恒电流充放电测试、循环伏安法(CV)和电化学阻抗谱(EIS)表征其作为锂离子电池负极材料的电化学性能。结果表明，糖类前驱体衍生的热解炭和直径为4~5 nm的SnO₂纳米点生成了稳定的复合结构，炭基体的缓冲作用和材料纳米化缓解了SnO₂的体积膨胀效应，使材料的结构稳定性和电化学性能提高。由于葡萄糖热解炭的有序度比淀粉热解炭更高，这组试样具有更好的循环性能和倍率性能，在2 A/g大电流密度下其比容量高于400 mAh/g。     

沉淀法制备氟羟基磷灰石的影响因素

采用沉淀法制备了纳米氟羟基磷灰石(FHA), 研究了合成温度、初始氟离子浓度和 pH 值对氟替代的影响. 用 X 射线衍射和红外光谱表征了FHA粉体的物相组成和晶体结构变化, 用透射电镜观察了FHA的形貌. 结果表明: 氟替代会导致晶格参数和键能的变化, 随着合成温度或原料中氟浓度的升高, FHA 晶粒尺寸和长径比增大; 相组成主要受pH值控制, 考虑到OH^–和F ^–对羟基空位的竞争, 高pH值不利于氟替代.     

氧化铈空心球可控合成及其对Pt基催化剂电催化性能的影响

采用水热合成法, 以碳球为模板, 改变焙烧升温速率, 控制影响铈物种的扩散、渗透及碳球结构的收缩率, 制备了单、双壳层CeO₂空心球。通过微波辅助乙二醇还原氯铂酸法制备了Pt-CeO₂/RGO催化剂, 研究了CeO₂空心球的添加对Pt基催化剂电催化性能的影响。利用X射线衍射仪(XRD)、比表面积及孔径分析仪(BET)、扫描电镜(SEM)和电子能谱(EDAX)、透射电镜(TEM)、X射线光电子能谱(XPS)对CeO₂及催化剂的微观结构进行了表征, 利用电化学工作站对催化剂进行电化学性能测试。结果表明: 单、双壳层CeO₂空心球的比表面积为124.44 m²/g、140.95 m²/g, 孔容为0.014427 cm³/(g·nm)、0.018605 cm³/(g·nm), 孔径分布在2~4 nm范围内。催化剂中的CeO₂保持原有的球状形貌, Pt纳米粒子主要分布在CeO₂附近; 当RGO∶CeO₂=1∶2时, 添加了双壳层CeO₂空心球的Pt-CeO₂/RGO催化剂的电催化性能最优, 电化学活性表面积为94.27 m²/g, 对乙醇氧化的峰电流密度值为613.54 A/g, 1000 s的稳态电流密度值为135.45 A/g。     

Crystal structure, thermal expansion and electrical conductivity of Nd0.7Sr0.3Fe1−xCoxO3 (0≤x≤0.8)

The crystal structure, thermal expansion and electrical conductivity of the solid solution Nd_0.7Sr_0.3Fe_1−xCo_xO₃ for 0≤x≤0.8 were investigated. All compositions had the GdFeO₃-type orthorhombic perovskite structure. The lattice parameters were determined at room temperature by X-ray powder diffraction (XRPD). The pseudo-cubic lattice constant decreased continuously with x. The average linear thermal expansion coefficient (TEC) in the temperature range from 573 to 973 K was found to increase with x. The thermal expansion curves for all values of x displayed rapid increase in slope at high temperatures. The electrical conductivity increased with x for the entire temperature range of measurement. The calculated activation energy values indicate that electrical conduction takes place primarily by the small polaron hopping mechanism. The charge compensation for the divalent ion on the A-site is provided by the formation of Fe⁴⁺ ions on the B-site (in preference to Co⁴⁺ ions) and vacancies on the oxygen sublattice for low values of x. The large increase in the conductivity with x in the range from 0.6 to 0.8 is attributed to the substitution of Fe⁴⁺ ions by Co⁴⁺ ions. The Fe site has a lower small polaron site energy than Co and hence behaves like a carrier trap, thereby drastically reducing the conductivity. The non-linear behaviour in the dependence of log σT with reciprocal temperature can be attributed to the generation of additional charge carriers with increasing temperature by the charge disproportionation of Co³⁺ ions.     

Preparation and characterization of morph-genetic aluminum nitride/carbon composites from filter paper

Morph-genetic aluminum nitride/carbon composites with cablelike structure were prepared from filter paper template through the surface sol-gel process and carbothermal nitridation reaction. The resulting materials have a hierarchical structure originating from the morphology of cellulose paper. The aluminum nitride/carbon composites have the core-shell microstructure, the core is graphitic carbon, and the shell is aluminum nitride nanocoating formed by carbothermal nitridation reduction of alumina with the interfacial carbon in nitrogen atmosphere. Scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, and transmission electron microscope were employed to characterize the structural morphology and phase compositions of the final products.     

Synthesis and photochromic properties of EDTA-induced MoO3 powder

In this study, the photochromic MoO₃ powder with novel morphology has been synthesized via hydrothermal method, using ethylene diamine tetraacetice acid (EDTA) as organic inducing agent. The influence of EDTA on the morphology, structure and photochromic properties of MoO₃ powder has been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), as well as ultraviolet and visible spectroscopy (UV-vis) and color difference meter. When the molar ratio of EDTA/Mo⁶⁺ is 0.05:1, the EDTA-induced MoO₃ powder is found to have 3D flower-like morphologies and excellent photochromic properties. Furthermore, the possible growth mechanism of the flower-like structure and the photochromic mechanism of MoO₃ powder are also discussed in detail.     

MgCo_(2)O_(4)海胆状电极材料的制备及其电化学性能EI北大核心CSCD

采用水热法制得一种尖晶石型MgCo_(2)O_(4)海胆状电极材料,并通过X射线衍射(XRD)、X射线光电子能谱分析(XPS)、扫描电镜(SEM)、透射电镜(TEM)以及电化学工作站对产物进行了表征和电化学性能测试。通过改变所制备材料的水热反应时间,制备出团簇结构、分布较均匀以及密集度较高的MgCo_(2)O_(4)海胆状形貌。结果表明,当水热反应时间为6 h时所获得的MgCo_(2)O_(4)电极材料结构较为完善、尺寸较为均匀、电化学性能较为优异,而且在电流密度为1 mA/cm^(2)情况下,面积比电容高达6.75 F/cm^(2)。另外,对该MgCo_(2)O_(4)海胆状材料在20 mA/cm^(2)的电流密度下循环1000周次后,面积比电容保持为原来的88.4%,表现出良好的循环性能。     

Crystal growth and spectral properties of pure and Co-doped Mg3B2O6 crystal

Novel pure and cobalt-doped magnesium borate crystals (Mg₃B₂O₆) have been grown successfully by the Czochralski technique for the first time. Crystal growth, X-ray powder diffraction (XRD) analysis, absorption spectrum, fluorescence spectrum as well as fluorescence decay curve of Co²⁺:Mg₃B₂O₆ (MBO) were described. From the absorption peaks for the octahedral Co²⁺ ions, the crystal-field parameter Dq and the Racah parameter B were estimated to be 943.3 cm⁻¹ and 821.6 cm⁻¹, respectively. The fluorescence lifetime of the transition ⁴T₁(⁴P) → ⁴T₂ centered at 717 nm was measured to be 9.68 ms.