Oxidation of cobalt based Fischer–Tropsch catalysts as a deactivation mechanism

The oxidation of supported cobalt based slurry bed Fischer–Tropsch catalysts by means of water was studied. Water is one of the Fischer–Tropsch reaction products and can probably cause oxidation and deactivation of a reduced cobalt catalyst. Model experiments using Mössbauer emission spectroscopy and thermogravimetry as well as realistic Fischer–Tropsch synthesis runs were performed. It was demonstrated that Mössbauer emission spectroscopy can successfully be applied to the investigation of high cobalt loading Fischer–Tropsch catalysts. Strong indications were found that oxidation of reduced cobalt catalysts occurs under realistic Fischer–Tropsch conditions. Mössbauer emission spectroscopy and thermogravimetry results showed that the oxidation depends on the P_H2/P_H2O ratio, and that oxidation proceeds to less than complete extents under certain conditions. The formation of both reducible and less reducible cobalt oxide species was observed, and the relative ratio between these species depends on the severity of the oxidation conditions.     

Optimization of the pretreatment procedure in the design of cobalt silica supported Fischer–Tropsch catalysts

The effect of cobalt precursor, catalyst pretreatment and promotion with ruthenium and rhenium on the formation of cobalt metal nanoparticles and catalytic performance of supported Fischer–Tropsch (FT) catalysts was studied using a combination of techniques (DSC–TGA, UV–vis spectroscopy, XPS, XRD, EXAFS–XANES, in situ magnetization measurements, propene chemisorption and catalytic measurements). The cobalt promoted and unpromoted catalysts were prepared by aqueous co-impregnation using cobalt nitrate or acetate, ruthenium nitrosyl nitrate or perrhenic acid. In both unpromoted and Ru and Re-promoted cobalt catalysts after impregnation and drying, cobalt is present mainly in octahedrally coordinated complexes. The repartition of cobalt species between Co₃O₄ and cobalt silicate depends essentially on the exothermicity of precursor decomposition. Cobalt nitrate precursor, with an endothermic decomposition, favors Co₃O₄ crystallites. Lower temperature of cobalt nitrate decomposition and catalyst calcination generally leads to higher dispersion of supported cobalt oxide. Cobalt acetate precursor, with an exothermic decomposition, favors cobalt silicate. By optimizing the conditions of cobalt acetate decomposition, the fraction of cobalt silicate can be decreased favoring a more reducible Co₃O₄ phase. For the catalysts prepared from cobalt nitrate, promotion with ruthenium increases the cobalt dispersion, while maintaining high reducibility. For the catalyst prepared via low temperature decomposition of cobalt acetate, addition of ruthenium increases the fraction of Co₃O₄ crystalline phase and decreases the concentration of barely reducible cobalt silicate. The Fischer–Tropsch reaction rates over unpromoted and promoted cobalt catalysts were found to be primarily a function of the number of cobalt metal sites, which are generated by the reduction of Co₃O₄ crystallites.     

Comparison of preparation methods for carbon nanotubes supported iron Fischer–Tropsch catalysts

Carbon nanotubes supported iron catalysts were prepared by incipient wetness, deposition/precipitation using K₂CO₃, and deposition/precipitation using urea. The incipient wetness method and the deposition/precipitation technique using urea yielded highly dispersed Fe³⁺ on the carbon nanotubes support. The deposition/precipitation technique using K₂CO₃ also yielded larger Fe₂O₃-crystallites. After reduction the three catalysts had similar metal surface areas. Nevertheless, the activity of these catalysts in the Fischer–Tropsch synthesis differed significantly with the catalyst prepared by incipient wetness being the most active one. It is speculated that the differences in the performance of the catalysts might be attributed to the different crystallite size distributions, which would result in a variation in the amount of the different phases present in the catalyst under reaction conditions. The selectivity in the Fischer–Tropsch synthesis over the three catalysts seems to be independent of the method of preparation.     

Structural changes and activation treatment in a Co/SiO2 catalyst for Fischer–Tropsch synthesis

We examined the effect of the activation process on the structural and morphological characteristics of a cobalt-based catalyst for Fischer–Tropsch synthesis. A 10 wt.% Co/SiO₂ catalyst prepared by wet impregnation was separately activated under H₂, CO or a H₂/CO mixture. The structural changes during activation from 298 to 773 K were studied by in situ X-ray diffraction. Catalysts were examined by SEM, TEM, XPS and in situ DRIFT-MS. The H₂/CO activation produced redispersion of cobalt particles and simultaneous carbon nanostructures formation. The catalyst showed the highest performance in the Fischer–Tropsch synthesis after the H₂/CO activation.     

Application of in situ Mössbauer spectroscopy to investigate the effect of precipitating agents on precipitated iron Fischer–Tropsch catalysts

The type of the precipitating agent used during the preparation of a precipitated iron-based Fischer–Tropsch (FT) catalyst affects the catalyst pore structure, crystallite size, phase composition and catalytic behavior. Catalysts prepared by using precipitating agents, that contain carbonate ions, have pores that are larger than those of catalysts prepared using precipitating agents that contain hydroxides. Precipitation at pH>8, using aqueous NH₃ solution as a precipitating agent, results in the formation of large crystallites of FeOOH, which are not observed when Na₂CO₃ and K₂CO₃ are used. Higher % CO conversion during FT synthesis was observed with the catalyst prepared by using aqueous NH₃ solution. However, this is correlated with a low selectivity for the formation of olefins. For all catalysts, in situ Mössbauer spectra recorded during FT synthesis show that the % CO conversion increases with the formation of iron carbides, viz. ′-Fe_2.2C and χ-Fe_2.5C.     

Silica supported cobalt Fischer–Tropsch catalysts: effect of pore diameter of support

The influence of the effect of average pore diameter of silica support on the physical and chemical properties of supported cobalt catalysts and their performance in the Fischer–Tropsch synthesis was investigated. Silicas with different mean pore diameter (20, 40, 60, 100 and 150 Å) were impregnated with cobalt nitrate to produce catalysts containing 20 wt.% cobalt. The metal crystallite size and degree of reduction was found to increase with increasing pore diameter of the support for supports with an average pore diameter larger or equal to 40 Å, and hence the dispersion decreased. In impregnated catalysts, the metal crystallites seems to appear in clusters on the support. With increasing average pore diameter, the size of these clusters increases. In the Fischer–Tropsch synthesis, the 100 Å supported catalyst proved to be the most active and selective catalyst for hydrocarbon formation. The C₅₊ and methane selectivity passed through a maximum and minimum at the 100 Å supported catalyst, respectively, which can be explained quantitatively using the reactant transport model proposed by Iglesia et al.     

CO and CO2 hydrogenation study on supported cobalt Fischer–Tropsch synthesis catalysts

The conversion of CO/H₂, CO₂/H₂ and (CO+CO₂)/H₂ mixtures using cobalt catalysts under typical Fischer–Tropsch synthesis conditions has been carried out. The results show that in the presence of CO, CO₂ hydrogenation is slow. For the cases of only CO or only CO₂ hydrogenation, similar catalytic activities were obtained but the selectivities were very different. For CO hydrogenation, normal Fischer–Tropsch synthesis product distributions were observed with an of about 0.80; in contrast, the CO₂ hydrogenation products contained about 70% or more of methane. Thus, CO₂ and CO hydrogenation appears to follow different reaction pathways. The catalyst deactivates more rapidly for the conversion of CO than for CO₂ even though the H₂O/H₂ ratio is at least two times larger for the conversion of CO₂. Since the catalyst ages more slowly in the presence of the higher H₂O/H₂ conditions, it is concluded that water alone does not account for the deactivation and that there is a deactivation pathway that involves the assistance of CO.     

Performance and characterization of Ru/Al2O3 and Ru/SiO2 catalysts modified with Mn for Fischer–Tropsch synthesis

Mn effect and characterization on γ-Al₂O₃-, -Al₂O₃- and SiO₂-supported Ru catalysts were investigated for Fischer–Tropsch synthesis under pressurized conditions. In the slurry phase Fischer–Tropsch reaction, γ-Al₂O₃ catalysts showed higher performance on CO conversion and C₅⁺ selectivity than -Al₂O₃ and SiO₂ catalysts. Moreover, Ru/Mn/γ-Al₂O₃ exhibited high resistance to catalyst deactivation and other catalysts were deactivated during the reaction. From characterization results on XRD, TPR, TEM, XPS and pore distribution, Ru particles were clearly observed over the catalysts, and γ-Al₂O₃ catalysts showed a moderate pore and particle size such as 8 nm, where -Al₂O₃ and SiO₂ showed highly dispersed ruthenium particles. The addition of Mn to γ-Al₂O₃ enhanced the removal of chloride from RuCl₃, which can lead to the formation of metallic Ru with moderate particle size, which would be an active site for Fischer–Tropsch reaction. Concomitantly, manganese chloride is formed. These schemes can be assigned to the stable nature of Ru/Mn/γ-Al₂O₃ catalyst.     

Fischer–Tropsch synthesis over Co–SiO2 catalysts prepared by the sol–gel method

Fischer–Tropsch synthesis was carried out in slurry phase over uniformly dispersed Co–SiO₂ catalysts prepared by the sol–gel method. When 0.01–1 wt.% of noble metals were added to the Co–SiO₂ catalysts, a high and stable catalytic activity was obtained over 60 h of the reaction at 503 K and 1 MPa. The addition of noble metals increased the reducibility of surface Co on the catalysts, without changing the particle size of Co metal significantly. High dispersion of metallic Co species stabilized on SiO₂ was responsible for stable activity. The uniform pore size of the catalysts was enlarged by varying the preparation conditions and by adding organic compounds such as N,N-dimethylformamide and formamide. Increased pore size resulted in decrease in CO conversion and selectivity for CO₂, a byproduct, and an increase in the olefin/paraffin ratio of the products. By modifying the surface of wide pore silica with Co–SiO₂ prepared by the sol–gel method, a bimodal pore structured catalyst was prepared. The bimodal catalyst showed high catalytic performance with reducing the amount of the expensive sol–gel Co–SiO₂.     

Fischer–Tropsch synthesis. Conversion of alcohols over iron oxide and iron carbide catalysts

Both iron oxide (Fe₂O₃) and iron carbide catalysts are active for the dehydration of tertiary alcohols; the oxide catalyst is not reduced nor is the bulk carbide oxidized by the steam generated during the dehydration reaction. Secondary alcohols are selectively converted to ketones plus hydrogen by both the iron oxide and carbide catalyst. Fe₂O₃ is reduced to Fe₃O₄ during the conversion of secondary alcohols. Both iron carbide and oxide catalysts dehydrogenate a primary alcohol (C_n) to an aldehyde which undergoes a secondary ketonization reaction to produce a symmetrical ketone with 2n−1 carbons. These results plus those of our earlier ¹⁴C-tracer studies suggest that dehydration of alcohols to produce olefins makes a minor, if any, contribution during Fischer–Tropsch synthesis with an iron catalyst at low and intermediate pressure conditions.     

Transient studies of the elementary steps of Fischer–Tropsch synthesis

The pulse transient method has been used to study the kinetics of several key steps of Fischer–Tropsch (FT) synthesis over cobalt supported catalysts. These elementary steps involve chemisorption of hydrogen and propene, and chemisorption and hydrogenation of carbon monoxide. It is found that at the conditions of Fischer–Tropsch synthesis, hydrogen chemisorption is reversible and quasi-equilibrated, while carbon monoxide adsorption is generally irreversible. Chemisorption of propene on cobalt metal sites results in its rapid autohydrogenation to propane and simultaneous formation of C_xH_y surface species.

The transient response curves produced during hydrogenation of carbon monoxide pulses in a flow of hydrogen have been analyzed using the modified Kobayashi model, which involves irreversible chemisorption and dissociation of carbon monoxide, quasi-equilibrated adsorption of hydrogen and reversible adsorption of water. The kinetic analysis suggests that oxygen-containing species are probably the most abundant surface intermediates. Desorption of water from the catalysts seems to be much slower than hydrogenation of surface carbon species.     

Fischer–Tropsch synthesis on monolithic catalysts of different materials

Monolithic structures made of cordierite, γ-Al₂O₃ and steel have been prepared as catalysts and tested for Fischer–Tropsch activity. The monoliths made of cordierite and steel were washcoated with a 20 wt.% Co–1 wt.% Re/γ-Al₂O₃ Fischer–Tropsch catalyst whereas the γ-Al₂O₃ monoliths were made by direct impregnation with an aqueous solution of the Co and Re salts resulting in a loading of 12 wt.% Co and 0.5 wt.% Re. The activity and selectivity of the different monoliths were compared with the corresponding powder catalysts.

Higher washcoat loadings resulted in decreased C₅₊ selectivity and olefin/paraffin ratios due to increased transport limitations. The impregnated γ-Al₂O₃ monoliths also showed similar C₅₊ selectivities as powder catalysts of small particle size (38–53 μm). Lower activities were observed with the steel monoliths probably due to experimental problems.     

Fischer–Tropsch synthesis over Re-promoted Co supported on Al2O3, SiO2 and TiO2: Effect of water

The activity and selectivity of rhenium promoted cobalt Fischer–Tropsch catalysts supported on Al₂O₃, TiO₂ and SiO₂ have been studied in a fixed-bed reactor at 483 K and 20 bar. Exposure of the catalysts to water added to the feed deactivates the Al₂O₃ supported catalyst, while the activity of the TiO₂ and SiO₂ supported catalysts increased. However, at high concentrations of water both the SiO₂ and TiO₂ supported catalyst deactivated. Common for all catalysts was an increase in C₅₊ selectivity and a decrease in the CH₄ selectivity by increasing the water partial pressure. The catalysts have been characterized by scanning transmission electron microscope (STEM), BET, H₂ chemisorption and X-ray diffraction (XRD).     

Comparative study of iron-based Fischer–Tropsch synthesis catalyst promoted with potassium or sodium

FeCu/SiO₂ catalysts, in which K or Na promoter is incorporated respectively, are prepared by a combination method of continuous co-precipitation and spray drying technology. The catalysts were characterized by temperature-programmed desorption and Mössbauer spectroscopy. The Fischer–Tropsch synthesis (FTS) performance of the catalysts was studied in a continuously stirred tank slurry reactor. The basicity of the K-promoted catalyst is enhanced, as demonstrated by CO₂-TPD results. MES results show that sodium can weaken the dispersion of α-Fe₂O₃ phase; either potassium or sodium can promote carburization of the catalyst, while the effect of sodium is weaker. FTS results indicate that the addition of K or Na can improve the catalyst activity, and shift the product distribution to heavy hydrocarbons to the different extent.     

Cobalt species in promoted cobalt alumina-supported Fischer–Tropsch catalysts

The structure of cobalt species at different stages of the genesis of monometallic and Pt-promoted cobalt alumina-supported Fischer–Tropsch catalysts was studied using X-ray diffraction, UV–visible spectroscopy, in situ X-ray absorption, in situ magnetic method, X-ray photoelectron spectroscopy, and DSC–TGA thermal analysis. The catalysts were prepared by incipient wetness impregnation using solutions of cobalt nitrate and dihydrogen hexachloroplatinate. Both variation of catalyst calcination temperature between 473 and 773 K and promotion with 0.1 wt% of Pt had no significant affect on the size of supported Co₃O₄ crystallites. The size of cobalt oxide particles in the calcined catalysts seems to be influenced primarily by the pore diameter of the support. Cobalt reducibility was relatively low in monometallic cobalt alumina-supported catalysts and decreased as a function of catalyst calcination temperature. The effect was probably due to the formation of mixed surface compounds between Co₃O₄ and Al₂O₃ at higher calcination temperatures, which hinder cobalt reduction. Promotion with platinum spectacularly increased the rate of cobalt reduction; the promotion seemed to reduce the activation energy of the formation of cobalt metallic phases. Analysis of the magnetization data suggests that the presence of Pt led to the reduction of smaller cobalt oxide particles, which could not be reduced at the same conditions in the cobalt monometallic catalysts. Promotion of cobalt alumina-supported catalysts with small amounts of Pt resulted in a significant increase in Fischer–Tropsch cobalt time yield. The efficient control of cobalt reducibility through catalyst calcination and promotion seems to be one of the key issues in the design of efficient cobalt alumina-supported Fischer–Tropsch catalysts.     

C-tracer study of the Fischer–Tropsch synthesis: another interpretation

The ¹³C-tracer results from the introduction of ¹³C₂H₄ into syngas prior to conversion with a rhodium catalyst have been used to support a surface vinyl mechanism for Fischer–Tropsch synthesis. The results were first interpreted by a mechanism that involved a decrease in ¹³C species on the surface as the carbon number increased. This model is shown to be incorrect. Considering only the ¹³C-labeled products, the data are consistent with earlier tracer studies showing that the added ¹³C₂H₄ initiates chains.     

Fe–Co based metal/spinel to produce light olefins from syngas

New metal/oxide (Co–Fe) catalysts (with no reduction or thermal pre-treatment) are efficient to produce light hydrocarbons with a low selectivity in CO₂ by the Fischer–Tropsch synthesis. The low selectivity in CO₂ is due to the occurrence of the CO₂/H₂ reaction. These materials are stable under reaction conditions, and only few carbides are formed during the Fischer–Tropsch reaction. X-ray analyses indicate that the most degraded phase is the (Co–Fe) alloy phase in CO/H₂ reaction and the spinel phase in the CO₂/H₂ reaction. It was demonstrated that these composites do not behave as the simple sum of a spinel phase and a (Co–Fe) alloy but have their own properties.     

Fischer–Tropsch synthesis using monolithic catalysts

Square channel cordierite monoliths have been loaded with alumina washcoat layers of various thicknesses (20–110 μm) and loaded with rhenium and cobalt resulting in a 0.1 wt.% Re/17 wt.% Co/Al₂O₃ catalyst. These monolithic catalysts have been tested in the Fischer–Tropsch synthesis in a temperature window (180–225 °C) under synthesis gas compositions ranging from stoichiometrically excess carbon monoxide to excess hydrogen (H₂/CO = 1–3). The results include data on the activity and selectivity of CoRe/Al₂O₃ monolithic catalysts for FTS under these process conditions. Washcoat layers thicker than about 50 μm appear to lead to internal diffusion limitations. Thinner washcoat layers yield, depending on the conditions, to larger amounts of -olefins than alkanes for chain lengths below 10 carbon atoms. ASF and non-ASF chain length distributions are obtained for thin washcoats, whereby the chain growth probability increases from 0.83 to 0.93. Under certain conditions the amounts of alkanes even increase with chain length. These experimental results with different diffusion lengths have been used to analyze the effects of secondary reactions on FTS selectivity.     

Fischer–Tropsch synthesis on monolithic catalysts with oil circulation

Monolithic catalysts made of cordierite and γ-Al₂O₃ have been prepared and tested for the Fischer–Tropsch (FT) synthesis. When operated without oil circulation, washcoated cordierite monoliths have previously been shown to be as active and selective as the corresponding powder catalyst provided that the monoliths have low washcoat loadings. Two-phase operation, i.e. with oil/product circulation during reaction, resulted in improved heat removal and temperature control, in lower apparent activity and faster deactivation, but the C₅₊ selectivity was equal to or even better than without oil circulation. The lower apparent activities obtained with oil circulation seem to be a combination of catalyst deactivation and flow-related problems in the present experimental set-up.     

Novel utilization of MCM-22 molecular sieves as supports of cobalt catalysts in the Fischer–Tropsch synthesis

Cobalt catalysts (2–10 wt% Co) supported on silica-rich MCM-22 zeolites have been prepared by impregnation with aqueous Co(NO₃)₂ solutions. The catalysts are characterized by X-ray fluorescence (XRF), X-ray diffraction (XRD), nitrogen adsorption, solid state nuclear magnetic resonance (NMR), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). The catalytic properties for the Fischer–Tropsch synthesis (FTS) at 280 °C, 12.5 bar and H₂/CO = 2 are evaluated. The catalysts supported on MCM-22 exhibit the highest selectivity to long-chain (C₅₊) hydrocarbons when MCM-22 supports are synthesized with the appropriate Si/Al ratio.