Determination of active palladium species in ZSM-5 zeolite for selective reduction of nitric oxide with methane

The active site in ZSM-5 zeolite-supported palladium, which shows the catalytic activity for NO reduction with methane as a reducing agent, has been investigated qualitatively and quantitatively by means of NO chemisorption and NaCl titration, comparing with PdO supported on silica. Palladium species in 0.4 wt.% Pd loaded H-ZSM-5 can adsorb NO equimolarly after calcination at 773 K, and almost all the NO was desorbed at around 673 K, while the palladium species on PdO/SiO₂ hardly adsorbed NO. The palladium species in Pd(0.4)/H-ZSM-5 are ion-exchangeable with Na⁺ in NaCl solution, indicating that they exist in a cationic state of an isolated Pd²⁺. This method for quantitative analysis of the isolated Pd²⁺ cations is named as ‘NaCl titration’. The amount of the isolated Pd²⁺ cationic species increased with increasing palladium content on Pd/H-ZSM-5, and PdO co-existed above 1 wt.%. The amount of the isolated Pd²⁺ cation was unchanged after the reaction of NO₂–CH₄, NO₂–CH₄–O₂, or CH₄–O₂ at 673 K, while the adsorbed amount of NO per the Pd²⁺ as determined by NO-TPD decreased after the NO₂–CH₄–O₂ reaction. It was found by NaCl titration that the catalytic activity of Pd/H-ZSM-5 for NO₂–CH₄–O₂ reaction increased with increasing amount of the isolated Pd²⁺ cationic species up to 0.7 wt.%, while the increase in the amount of PdO led to decrease in selectivity towards NO₂ reduction. The palladium species that are active and selective for NO reduction with CH₄ will be proposed.     

The effect of oxygen concentration on the reduction of NO with propylene over CuO/γ-Al2O3

The effect of oxygen concentration on the pulse and steady-state selective catalytic reduction (SCR) of NO with C₃H₆ over CuO/γ-Al₂O₃ has been studied by infrared spectroscopy (IR) coupled with mass spectroscopy studies. IR studies revealed that the pulse SCR occurred via (i) the oxidation of Cu⁰/Cu⁺ to Cu²⁺ by NO and O₂, (ii) the co-adsorption of NO/NO₂/O₂ to produce Cu²⁺(NO₃⁻)₂, and (iii) the reaction of Cu²⁺(NO₃⁻)₂ with C₃H₆ to produce N₂, CO₂, and H₂O. Increasing the O₂/NO ratio from 25.0 to 83.4 promotes the formation of NO₂ from gas phase oxidation of NO, resulting in a reactant mixture of NO/NO₂/O₂. This reactant mixture allows the formation of Cu²⁺(NO₃⁻)₂ and its reaction with the C₃H₆ to occur at a higher rate with a higher selectivity toward N₂ than the low O₂/NO flow. Both the high and low O₂/NO steady-state SCR reactions follow the same pathway, proceeding via adsorbed C₃H₇---NO₂, C₃H₇---ONO, CH₃COO⁻, Cu⁰---CN, and Cu⁺---NCO intermediates toward N₂, CO₂, and H₂O products. High O₂ concentration in the high O₂/NO SCR accelerates both the formation and destruction of adsorbates, resulting in their intensities similar to the low O₂/NO SCR at 523–698 K. High O₂ concentration in the reactant mixture resulted in a higher rate of destruction of the intermediates than low O₂ concentration at temperatures above 723 K.     

The bifunctional reaction pathway and dual kinetic regimes in NOx SCR by methane over cobalt mordenite catalysts

The pathway for selective reduction of NO_x by methane over Co mordenite cataysts has been studied by comparing the rates of the individual reactions (NO oxidation, CH₄ oxidation, NO₂ reduction) with that of the combined reaction (NO + O₂ + CH₄). Co⁽⁺²⁾ was exchanged into H-MOR and Na-MOR to give catalysts with different metal loading and number of support protons. Additionally, exchanged Co⁽⁺²⁾ ions were precipitated with NaOH to produce dispersed cobalt oxide on Na-MOR. The NO oxidation rate is the same for ion exchanged Co⁽⁺²⁾ ions in H-MOR and Na-MOR, but the rate of Co⁽⁺²⁾ ions is much lower than that of cobalt oxide. NO oxidation equilibrium is obtained only for those catalysts with high metal loading, cobalt oxide or run at low GHSV. Under the conditions of selective catalytic reduction, methane oxidation by O₂ is low for all catalysts. The turnover frequency of Co on Na-MOR, however, is higher than that on H-MOR. The rate of NO₂ reduction to N₂ is directly proportional to the number of support acid sites and independent of the amount of Co. Comparison of the rates and selectivities for the individual reactions with the combined reaction of NO + O₂ + CH₄ indicates that there are two types of catalysts. For the first, the NO oxidation is in equilibrium and the rate determining step is reduction of NO₂. For these catalysts, the rate (and selectivity) for formation of N₂ is identical from NO + O₂ + CH₄ and NO₂ + CH₄. These catalysts have high metal loading and few acid sites. Nevertheless, the rate of N₂ formation increases with increasing number of protons. For the second type of catalyst, NO oxidation is not in equilibrium and is the rate limiting step. For these catalysts the rate of N₂ formation increases with increasing metal loading. Neither catalyst type, however, is optimized for the maximum formation of N₂. By using a mixture of catalysts, one with high NO oxidation activity and one with a large number of Brønsted acid sites, the rate of N₂ is greater than the weighted sum of the individual catalysts. The current results support the proposal that the pathway for selective catalytic reduction is bifunctional where metal sites affect NO oxidation, while support protons catalyze the formation of N₂.     

NO decomposition and reduction by CH4 over Sr/La2O3

Both NO decomposition and NO reduction by CH₄ over 4%Sr/La₂O₃ in the absence and presence of O₂ were examined between 773 and 973 K, and N₂O decomposition was also studied. The presence of CH₄ greatly increased the conversion of NO to N₂ and this activity was further enhanced by co-fed O₂. For example, at 773 K and 15 Torr NO the specific activities of NO decomposition, reduction by CH₄ in the absence of O₂, and reduction with 1% O₂ in the feed were 8.3·10⁻⁴, 4.6·10⁻³, and 1.3·10⁻² μmol N₂/s m², respectively. This oxygen-enhanced activity for NO reduction is attributed to the formation of methyl (and/or methylene) species on the oxide surface. NO decomposition on this catalyst occurred with an activation energy of 28 kcal/mol and the reaction order at 923 K with respect to NO was 1.1. The rate of N₂ formation by decomposition was inhibited by O₂ in the feed even though the reaction order in NO remained the same. The rate of NO reduction by CH₄ continuously increased with temperature to 973 K with no bend-over in either the absence or the presence of O₂ with equal activation energies of 26 kcal/mol. The addition of O₂ increased the reaction order in CH₄ at 923 K from 0.19 to 0.87, while it decreased the reaction order in NO from 0.73 to 0.55. The reaction order in O₂ was 0.26 up to 0.5% O₂ during which time the CH₄ concentration was not decreased significantly. N₂O decomposition occurs rapidly on this catalyst with a specific activity of 1.6·10⁻⁴ μmol N₂/s m² at 623 K and 1220 ppm N₂O and an activation energy of 24 kcal/mol. The addition of CH₄ inhibits this decomposition reaction. Finally, the use of either CO or H₂ as the reductant (no O₂) produced specific activities at 773 K that were almost 5 times greater than that with CH₄ and gave activation energies of 21–26 kcal/mol, thus demonstrating the potential of using CO/H₂ to reduce NO to N₂ over these REO catalysts.     

Preparation of supported Pt-M catalysts (M = Mo and W) from anion-exchanged hydrotalcites and their catalytic activity for low temperature NO-H2-O2 reaction

The NO-H₂-O₂ reaction was studied over supported bimetallic catalysts, Pt-Mo and Pt-W, which were prepared by coexchange of hydrotalcite-like Mg-Al double layered hydroxides by Pt(NO₂)₄²⁻, MoO₄²⁻, and/or WO₄²⁻ and subsequent heating at 600 °C in H₂. The Pt–Mo interaction could obviously be seen when the catalyst after reduction treatment was exposed to a mixture of NO and H₂ in the absence of O₂. The Pt-HT catalyst showed the almost complete NO conversion at 70 °C, whereas the Pt-Mo-HT showed a negligible conversion. Upon exposure to O₂, however, Pt-Mo-HT exhibited the NO conversion at the lowest temperature of ≥30 °C, compared to ≥60 °C required for Pt-HT. EXAFS/XANES, XPS and IR results suggested that the role of Mo is very sensitive to the oxidation state, i.e., oxidized Mo species residing in Pt particles are postulated to retard the oxidative adsorption of NO as NO₃ and promote the catalytic conversion of NO to N₂O at low temperatures.     

Photocatalytic oxidation of CO with various oxidants by Mo oxide species highly dispersed on SiO2 at 293 K

The photocatalytic oxidation of CO into CO₂ with oxidants such as NO, N₂O and O₂ proceeded efficiently on a Mo/SiO₂ with high Mo dispersion under UV light irradiation. It was found that the reaction rate greatly depended on the kind and concentration of the oxidant. Photoluminescence investigations reveal the close relationship between the reaction rate and the relative concentration of the photo-excited Mo⁶⁺-oxide species, i.e. charge transfer–excited–triplet state (Mo⁵⁺–O⁻)^*, under steady-state reaction conditions. Moreover, the photocatalytic oxidation of CO with O₂ in excess H₂ was carried out to test suitability for applications to supplying pure H₂. This reaction was seen to proceed efficiently on Mo/SiO₂ with a high CO conversion of 100% and CO selectivity of 99% after 180 min under UV light irradiation, showing higher photocatalytic performance than TiO₂ (P-25) photocatalyst. UV–vis, XAFS, photoluminescence and FT-IR investigations revealed that the high reactivity of the charge transfer–excited–triplet state (Mo⁵⁺–O⁻)^*, with CO as well as the high reactivity of the photoreduced Mo-oxide species (Mo⁴⁺-species) with O₂ to produce the original Mo-oxide species (Mo⁶⁺O²⁻), played a crucial role in the reactions.     

NO removal by CH4 on Co-NaX-CO and Ag-NaX catalysts in a dual-bed system

NO removal using CH₄ as a reductant in a dual-bed system has been investigated with Co-NaX and Ag-NaX catalysts, which were prepared by Co²⁺-, Ag⁺-ion exchange into zeolite NaX, respectively, and activation for 5 h at 500 °C. The experimental result has been compared with that of a Co-NaX-CO catalyst, additionally pre-treated under CO flow for the Co-NaX catalyst. The cobalt crystal structure of a Co-NaX-CO catalyst is Co₃O₄, which promotes NO oxidation to NO₂ by excess O₂ at a low temperature (523 K). The mechanical mixture of Co-NaX-CO and Ag-NaX catalysts shows a synergy effect on NO reduction to N₂ by CH₄ in the presence of excess O₂ and H₂O, but the NO reduction decreases quickly as time passes. However, the NO reduction to N₂ in a deNO bed at 523 K and a deNO₂ bed at 423 K, which are relatively lower than the reaction temperatures for common SCR systems, still remained at 67% even in a H₂O 10% gas mixture after 160 min.     

Investigation of CO oxidation and NO reduction on three-way monolith catalysts with transient response techniques

The kinetics of CO oxidation and NO reduction reactions over alumina and alumina-ceria supported Pt, Rh and bimetallic Pt/Rh catalysts coated on metallic monoliths were investigated using the step response technique at atmospheric pressure and at temperatures 30–350°C. The feed step change experiments from an inert flow to a flow of a reagent (O₂, CO, NO and H₂) showed that the ceria promoted catalysts had higher adsorption capacities, higher reaction rates and promoting effects by preventing the inhibitory effects of reactants, than the alumina supported noble metal catalysts. The effect of ceria was explained with adsorbate spillover from the noble metal sites to ceria. The step change experiments CO/O₂ and O₂/CO also revealed the enhancing effect of ceria. The step change experiments NO/H₂ and H₂/NO gave nitrogen as a main reduction product and N₂O as a by-product. Preadsorption of NO on the catalyst surface decreased the catalyst activity in the reduction of NO with H₂. The CO oxidation transients were modeled with a mechanism which consistent of CO and O₂ adsorption and a surface reaction step. The NO reduction experiments with H₂ revealed the role of N₂O as a surface intermediate in the formation of N₂. The formation of NN bonding was assumed to take place prior to, partly prior to or totally following to the NO bond breakage. High NO coverage favors N₂O formation. Pt was shown to be more efficient than Rh for NO reduction by H₂.     

Catalytic reduction of N2O over steam-activated FeZSM-5 zeolite: Comparison of CH4, CO, and their mixtures as reductants with or without excess O2

The catalytic reduction of N₂O by CH₄, CO, and their mixtures has been comparatively investigated over steam-activated FeZSM-5 zeolite. The influence of the molar feed ratio between N₂O and the reducing agents, the gas-hourly space velocity, and the presence of O₂ on the catalytic performance were studied in the temperature range of 475–850 K. The CH₄ is more efficient than CO for N₂O reduction, achieving the same degree of conversion at significantly lower temperatures. The apparent activation energy for N₂O reduction by CH₄ was very similar to that of direct N₂O decomposition (140 kJ mol⁻¹), being much lower for the N₂O reduction by CO (60 kJ mol⁻¹). This suggests that the reactions have a markedly different mechanism. Addition of CO using equimolar mixtures in the ternary N₂O + CH₄ + CO system did not affect the N₂O conversion with respect to the binary N₂O + CH₄ system, indicating that CO does not interfere in the low-temperature reduction of N₂O by CH₄. In the ternary system, CO contributed to N₂O reduction when methane was the limiting reactant. The conversion and selectivity of the reactions of N₂O with CH₄, CO, and their mixtures were not altered upon adding excess O₂ in the feed.     

Conversion of N2O to N2 on TiO2(1 1 0)

In this study, we examine the interaction of N₂O with TiO₂(1 1 0) in an effort to better understand the conversion of NO_x species to N₂ over TiO₂-based catalysts. The TiO₂(1 1 0) surface was chosen as a model system because this material is commonly used as a support and because oxygen vacancies on this surface are perhaps the best available models for the role of electronic defects in catalysis. Annealing TiO₂(1 1 0) in vacuum at high temperature (above about 800 K) generates oxygen vacancy sites that are associated with reduced surface cations (Ti³⁺ sites) and that are easily quantified using temperature programmed desorption (TPD) of water. Using TPD, X-ray photoelectron spectroscopy (XPS) and electron energy loss spectroscopy (EELS), we found that the majority of N₂O molecules adsorbed at 90 K on TiO₂(1 1 0) are weakly held and desorb from the surface at 130 K. However, a small fraction of the N₂O molecules exposed to TiO₂(1 1 0) at 90 K decompose to N₂ via one of two channels, both of which are vacancy-mediated. One channel occurs at 90 K, and results in N₂ ejection from the surface and vacancy oxidation. We propose that this channel involves N₂O molecules bound at vacancies with the O-end of the molecule in the vacancy. The second channel results from an adsorbed state of N₂O that decomposes at 170 K to liberate N₂ in the gas phase and deposit oxygen adatoms at non-defect Ti⁴⁺ sites. The presence of these O adatoms is clearly evident in subsequent water TPD measurements. We propose that this channel involves N₂O molecules that are bound at vacancies with the N-end of the molecule in the vacancy, which permits the O-end of the molecule to interact with an adjacent Ti⁴⁺ site. The partitioning between these two channels is roughly 1:1 for adsorption at 90 K, but neither is observed to occur for moderate N₂O exposures at temperatures above 200 K. EELS data indicate that vacancies readily transfer charge to N₂O at 90 K, and this charge transfer facilitates N₂O decomposition. Based on these results, it appears that the decomposition of N₂O to N₂ requires trapping of the molecule at vacancies and that the lifetime of the N₂O–vacancy interaction may be key to the conversion of N₂O to N₂.     

Effect of Na-addition on catalytic activity of Pt-ZSM-5 for low-temperature NO–H2–O2 reactions

The effect of additives on Pt-ZSM-5 catalysts was studied for the selective NO reduction by H₂ in the presence of excess O₂ (NO–H₂–O₂ reaction) at 100 °C. The reaction of NO in a stream of 0.08% NO, 0.28% H₂, 10% O₂, and He balance yielded N₂ with less than 10% selectivity, which could not be increased by changing Pt loading or H₂ concentration in the gas feed. Co-impregnation of NaHCO₃ and Pt onto ZSM-5 decreased the BET surface area and the Pt dispersion. Nevertheless, the Na-loaded catalyst (Na-Pt-ZSM-5) exhibited the higher NO_x conversion (>90%) and the N₂ selectivity (ca. 50%). Such a high catalytic activity even at high Na loadings (≥10 wt.%) is completely contrast to other Na-added Pt catalyst systems reported so far. Further improvement of N₂ selectivity was attained by the post-impregnation of NaHCO₃ onto Pt-ZSM-5. In situ DRIFT measurements suggested that the addition of Na promotes the adsorption of NO as NO₂⁻-type species, which would play a role of an intermediate to yield N₂. The introduction of Lewis base to the acidic supports including ZSM-5 would be applied to the catalyst design for selective NO–H₂–O₂ reaction at low temperatures.     

In situ FTIR characterization of the adsorption of CO and its reaction with NO on Pd-based FCC low NOx combustion promoters

The adsorption of CO and its reaction with NO in the 400–600 °C temperature range on Ceⁿ⁺/Na⁺/γ-Al₂O₃ and Pdⁿ⁺/Ceⁿ⁺/Na⁺/γ-Al₂O₃ type materials used commercially as FCC additives were monitored by FTIR spectroscopy. Exposure of both types of samples to CO leads to the formation of carboxylates and carbonates. The concentration of these species was higher in samples containing Pd, indicating that palladium catalyzes their formation. The Pdⁿ⁺ cations initially present in these samples undergo partial reduction to form metallic Pd in the presence of CO even at room temperature. More complete reduction of Pd, along with some aggregation, was observed after exposure to CO at elevated temperatures. Exposure of both types of samples to NO/CO mixtures in the 400–600 °C temperature range leads to the formation of surface isocyanate species. Both Na⁺ and Ceⁿ⁺ promote the formation of such NCO species. However, surface isocyanate species were formed with substantially higher rates in the presence of palladium. The formation of the isocyanate species strongly correlates with changes observed in the ν_OH region, indicating that hydroxyls actively participate in the surface chemistry involved and are capable of protonating the NCO species. The isocyanates are also reactive towards O₂ and NO yielding CO₂ and N₂. These results suggest that isocyanates are possibly involved as intermediates in the CO–NO reaction over the materials examined.     

Zeolite-mediated removal of NOx by NH3 from exhaust streams at low temperatures

NH₃ stored on zeolites in the form of NH₄⁺ ions easily reacts with NO to N₂ in the presence of O₂ at temperatures <373 K under dry conditions. Wet conditions require a modification of the catalyst system. It is shown that MnO₂ deposited on the external surface of zeolite Y by precipitation considerably enhances the NO_x conversion by zeolite fixed NH₄⁺ ions in the presence of water at 400–430 K. Particle-size analysis, temperature-programmed reduction, textural characterization, chemical analysis, ESR and XRD gave a subtle picture of the MnO₂ phase structure. The MnO₂ is a non-stoichiometric, amorphous phase that contains minor amounts of Mn²⁺ ions. It loses O₂ upon inert heating up to 873 K, but does not crystallize or sinter. The phase is reducible by H₂ in two stages via intermediate formation of Mn₃O₄. The manufacture of extrudates preserving stored NH₄⁺ ions for NO_x reduction is described. It was found that MnO₂ can oxidize NO by bulk oxygen. This enables the reduction of NO to N₂ by the zeolitic NH₄⁺ ions without gas-phase oxygen for limited time periods. The composite catalyst retains storage capacity for both, oxygen and NH₄⁺ ions despite the presence of moisture and allows short-term reduction of NO without gaseous O₂ or additional reductants. The catalyst is likewise suitable for steady-state DeNO_x operation at higher space velocities if gaseous NH₃ is permanently supplied.     

The role of lanthana loading on the catalytic properties of Pd/Al2O3-La2O3 in the NO reduction with H2

The role of La₂O₃ loading in Pd/Al₂O₃-La₂O₃ prepared by sol–gel on the catalytic properties in the NO reduction with H₂ was studied. The catalysts were characterized by N₂ physisorption, temperature-programmed reduction, differential thermal analysis, temperature-programmed oxidation and temperature-programmed desorption of NO.

The physicochemical properties of Pd catalysts as well as the catalytic activity and selectivity are modified by La₂O₃ inclusion. The selectivity depends on the NO/H₂ molar ratio (GHSV = 72,000 h⁻¹) and the extent of interaction between Pd and La₂O₃. At NO/H₂ = 0.5, the catalysts show high N₂ selectivity (60–75%) at temperatures lower than 250 °C. For NO/H₂ = 1, the N₂ selectivity is almost 100% mainly for high temperatures, and even in the presence of 10% H₂O vapor. The high N₂ selectivity indicates a high capability of the catalysts to dissociate NO upon adsorption. This property is attributed to the creation of new adsorption sites through the formation of a surface PdO_x phase interacting with La₂O₃. The formation of this phase is favored by the spreading of PdO promoted by La₂O₃. DTA shows that the phase transformation takes place at temperatures of 280–350 °C, while TPO indicates that this phase transformation is related to the oxidation process of PdO: in the case of Pd/Al₂O₃ the O₂ uptake is consistent with the oxidation of PdO to PdO₂, and when La₂O₃ is present the O₂ uptake exceeds that amount (1.5 times). La₂O₃ in Pd catalysts promotes also the oxidation of Pd and dissociative adsorption of NO mainly at low temperatures (<250 °C) favoring the formation of N₂.     

Abatement of CO from relatively simple and complex mixtures: II. Oxidation on Pd-Cu/C catalysts

A low-temperature abatement of carbon monoxide from mixtures as complicated as smoke was considered. Catalytic oxidation and chemisorption of CO on activated carbon-supported Pd and Cu catalysts were investigated. Heterogenized Wacker-type catalysts and the product of catalyst degradation, a dispersed Pd-Cu catalyst, were prepared and found to be promising for the smoke applications. Deactivation of the catalyst was found to be caused by the catalyst dehydration process, which appeared to be reversible. A heat treatment in a CO+O₂ reaction gas flow resulted in the conversion of a Wacker-type transition metal complex catalyst to Pd⁰ atoms or small clusters. This new system composed a very active chemisorbent of CO and a relatively stable oxidation catalyst at elevated temperatures. This immediately prepared catalyst showed 70% removal of CO from smoke. The elements of the mechanisms of CO oxidation were studied under the gas-flow and gas-pulse conditions.     

On the mechanism of model diesel soot-O2 reaction catalysed by Pt-containing La-doped CeO2: A TAP study with isotopic O2

Pt supported on CeO₂ and 10 wt.% La³⁺-doped CeO₂ catalysts have been prepared, characterised and tested for soot oxidation by O₂ in TGA. The reaction mechanism has been studied in a TAP reactor with labelled O₂. Isotopic oxygen exchange between molecular O₂ and ‘O’ on the support/catalyst was observed and soot oxidation is being carried out by lattice oxygen. TAP studies further show that Pt improves O₂ adsorption and, therefore, 5 wt.% Pt-containing catalysts are more active for soot oxidation than the counterpart supports. In addition, CeO₂ doping by La³⁺ leads to an improved support, since La³⁺ stabilises the structure of CeO₂ when calcined at high temperature (1000 °C) and minimises sintering. In addition, La³⁺ improves the Ce⁴⁺/Ce³⁺ reduction as deduced from H₂-TPR experiments and favours oxygen mobility into the lattice. A synergetic effect of Pt and La³⁺ is observed, Pt-containing La³⁺-doped CeO₂ being the most active catalyst for soot oxidation by O₂ among the samples studied.     

Contribution to the mechanism of NO reduction by CO over Pt/NaX zeolite

The reaction of NO + CO was studied over Pt/NaX prepared by the decomposition of [Pt(NH₃)₄]²⁺. The decomposition was carried out via calcination followed by reduction, by vacuum decomposition, and by decomposition in hydrogen, by ways which are known to lead to the formation of Pt clusters of different sizes and location. The NO reduction by CO was studied under static conditions for longer (20–30 min) and shorter (100 s) time intervals, and the reaction was followed by temperature programmed decomposition (TPD) of species adsorbed during the preceding isothermal reactions. The effect of various NO/CO ratios and of added oxygen was examined. The reactions of N₂O + CO were compared with those of NO + CO. The increasing size of Pt clusters enhances the reduction of NO by CO, but it is complicated at lower reaction temperatures (below 230°C) by the poisoning of active Pt centres, especially by adsorbed CO. Smaller Pt clusters exhibit higher preference towards NO adsorption from NO + CO mixtures than the larger Pt clusters. The incomplete reduction of NO to N₂O proceeds under our experimental conditions below 230°C, and is accompanied by the formation of adsorbed species. N₂O formation is enhanced by the increased NO/CO ratio and by the addition of oxygen. The reduction of nitrous oxide occurs much slower than that of nitric oxide, and therefore N₂O could play a role only as a surface intermediate in the CO + NO reaction.     

Role of active oxygen transients in selective catalytic reduction of N2O with CH4 over Fe-zeolite catalysts

Sharp NO and O₂ desorption peaks, which were caused by the decomposition of nitro and nitrate species over Fe species, were observed in the range of 520–673 K in temperature-programmed desorption (TPD) from Fe-MFI after H₂ treatment at 773 K or high-temperature (HT) treatment at 1073 K followed by N₂O treatment. The amounts of O₂ and NO desorption were dependent on the pretreatment pressure of N₂O in the H₂ and N₂O treatment. The adsorbed species could be regenerated by the H₂ and N₂O treatment after TPD, and might be considered to be active oxygen species in selective catalytic reduction (SCR) of N₂O with CH₄. However, the reaction rate of CH₄ activation by the adsorbed species formed after the H₂ and N₂O or the HT and N₂O treatment was not so high as that of the CH₄ + N₂O reaction over the catalyst after O₂ treatment. The simultaneous presence of CH₄ and N₂O is essential for the high activity of the reaction, which suggests that nascent oxygen species formed by N₂O dissociation can activate CH₄ in the SCR of N₂O with CH₄.     

Rôles of catalytic oxidation in control of vehicle exhaust emissions

Catalytic oxidation was initially associated with the early development of catalysis and it subsequently became a part of many industrial processes, so it is not surprising it was used to remove hydrocarbons and CO when it became necessary to control these emissions from cars. Later NOx was reduced in a process involving reduction over a Pt/Rh catalyst followed by air injection in front of a Pt-based oxidation catalyst. If over-reduction of NO to NH₃ took place, or if H₂S was produced, it was important these undesirable species were converted to NOx and SOx in the catalytic oxidation stage. When exhaust gas composition could be kept stoichiometric hydrocarbons, CO and NOx were simultaneously converted over a single Pt/Rh three-way catalyst (TWC). With modern TWCs car tailpipe emissions can be exceptionally low. NO is not catalytically dissociated to O₂ and N₂ in the presence of O₂, it can only be reduced to N₂. Its control from lean-burn gasoline engines involves catalytic oxidation to NO₂ and thence nitrate that is stored and periodically reduced to N₂ by exhaust gas enrichment. This method is being modified for diesel engines. These engines produce soot, and filtration is being introduced to remove it. The exhaust temperature of heavy-duty diesels is sufficient (250–400 °C) for NO to be catalytically oxidised to NO₂ over an upstream platinum catalyst that smoothly oxidises soot in the filter. The exhaust gas temperature of passenger car diesels is too low for this to take place all of the time, so trapped soot is periodically burnt in O₂ above 550 °C. Catalytic oxidation of higher than normal amounts of hydrocarbon and CO over an upstream catalyst is used to give sufficient temperature for soot combustion with O₂ to take place.     

Fe2+/H2O2体系内各种自由基在氧化NO中的作用

Fe²⁺/H₂O₂体系可分解产生多种氧化性自由基, 主要包括O₂^-·、·OH和HO₂·。本文实验研究了O₂^-·、·OH及HO₂·在Fe²⁺/H₂O₂体系氧化NO气体过程中的作用。结果表明:在本实验条件下, O₂^-·对NO气体的氧化作用不明显;·OH及HO₂·是该体系氧化NO气体的主要活性物质, 其中·OH的氧化作用更大。加快自由基的生成速率可以增强Fe²⁺/H₂O₂体系对NO气体的氧化能力, 但O₂的生成速率同时加快。只有少量·OH及HO₂·参与NO的氧化, ·OH与HO₂·之间的快速反应是Fe²⁺/H₂O₂体系氧化NO过程中H₂O₂利用率低的主要原因。