无水乙醇对双层油酸包覆结构中物理吸附层的影响

研究了无水乙醇洗涤次数对油酸包覆的Fe3O4磁性纳米颗粒表面包覆结构的影响。采用FT-IR和TGA联合表征了油酸包覆的Fe3O4磁性纳米颗粒经过无水乙醇洗涤前后表面包覆结构的变化,采用TEM观察了油酸包覆后Fe3O4磁性纳米颗粒的形貌。实验结果表明经过无水乙醇5次洗涤后,油酸包覆的Fe3O4磁性颗粒为双层包覆结构;经过无水乙醇20次洗涤后,无水乙醇将双层油酸包覆结构中的物理吸附层洗掉,造成双层油酸包覆的Fe3O4磁性颗粒演变为单层包覆结构。     

新型氨基化磁性树状分子纳米颗粒的制备与表征

采用化学共沉淀法,以FeC13.6H2O和FeSO4·7H2O为原料制备磁性Fe3O4纳米颗粒,采用3-氨丙基三乙氧基硅烷(APTES)、丙烯酸丁酯(BA)和无水乙二胺(EDA)对其进行修饰,制备了三代表面氨基化的磁性Fe3O4树状分子纳米颗粒,并对其进行结构表征与性能测试.结果表明:树状分子逐代修饰在磁性颗粒表面,氨基含量逐代增加,分别为0.41、0.69和0.87mmol/g; Fe3O4纳米颗粒平均尺寸在12nm左右,修饰后的三代磁性纳米颗粒的粒径逐代增加,分别为14、27和40nm左右;三代产品仍具备较高的饱和磁化强度,展现出了典型的超顺磁性.这种氨基功能化的磁性纳米粒子在细胞分选、固定化酶和靶向药物等诸多领域有着巨大应用潜力.     

SnO2/Fe3O4磁性光催化微纳米材料的制备与性能研究

以磁性纳米颗粒Fe3O4为核,SnCl4.5H2O、氨水、无水乙醇为原料,采用液相共沉淀法在Fe3O4表面包覆一层SnO2光催化剂。采用X射线衍射仪(XRD)及扫描电镜(SEM)分析了其成分和表面形貌。结果显示:Fe3O4纳米颗粒在实验过程中发生了团聚,尺寸增大;当Fe3O4与SnCl4.5H2O物质的量比为(1∶2)～(1∶4)时,SnO2能被较好地包覆在Fe3O4表面,形成核-壳结构的SnO2/Fe3O4复合光催化材料;600℃热处理能够形成结晶性良好的SnO2晶体,但此时Fe3O4转变为Fe2O3,失去了磁性。     

酸碱度对纳米Fe_3O_4磁性流体性能的影响

采用化学共沉淀法制备纳米Fe3O4磁性颗粒,并用油酸钠对其进行包覆改性,以煤油为基液制备出煤油基Fe3O4磁流体。对比分析了pH值=5和10.5条件下油酸钠包覆的Fe3O4磁性颗粒的性能差异,得出油酸钠在pH值=5时可以更好地包覆在Fe3O4磁性颗粒表面,其饱和磁化强度为58.0A·m2/kg,在此基础上制备出的磁流体的饱和磁化强度为20.2A·m2/kg,并且Fe3O4磁性颗粒分散较均匀。而油酸钠在pH值=10.5时包覆的Fe3O4磁性颗粒,其饱和磁化强度虽然高一些(67.8A·m2/kg),但制备出的磁流体稳定性较差,出现较为明显的沉降现象。     

巯基表面修饰磁性复合纳米粒子用于重金属离子去除的研究

采用化学共沉淀法合成磁性Fe3O4纳米粒子,并且利用正硅酸乙酯（TEOS）的水解和凝聚作用在Fe3O4纳米粒子表面沉积包覆一层SiO2,合成核壳式的Fe3O4@SiO2复合纳米粒子。以Fe3O4@SiO2纳米粒子为基体,将（3-巯基丙基）三乙氧基硅烷嫁接到纳米粒子表面,制备出巯基功能化的纳米材料,将其应用于对重金属离子...     

磁性聚苯乙烯微球的制备与表征

采用化学共沉淀法制备了Fe3O4纳米颗粒,以PEG-4000为表面活性剂进行表面修饰,制备了分散性良好的纳米Fe3O4磁流体.磁流体存在时,采用分散聚合法,以苯乙烯为单体制备了磁性高分子微球.TEM研究表明,Fe3O4纳米颗粒的平均粒径约为10nm,分散聚合所制备的磁性聚苯乙烯微球的平均粒径约为80nm;VSM研究表明,合成的Fe3O4纳米颗粒及磁性聚苯乙烯微球具有超顺磁性;FT-IR研究表明,Fe3O4纳米颗粒很好地包覆于聚苯乙烯中;XRD结果表明,分散聚合前后,Fe3O4纳米颗粒的晶体结构没有发生变化.     

核-壳型罗丹明6G磁性分子印迹固相萃取材料的合成与表征

采用化学共沉淀法制备Fe3O4磁性纳米粒子,以3-氨丙基三乙氧基硅烷(APTES)对其表面进行氨基硅烷化改性,形成Fe3O4@SiO2-NH2纳米粒子。以其作为磁性核,采用表面印迹技术,以罗丹明6G为模板,丙烯酰胺(AM)为功能单体,三羟甲基丙烷三甲基丙烯酸酯(TRIM)为交联剂,在Fe3O4@SiO2-NH2表面形成罗丹明6G分子印迹聚合膜,制备了核-壳型罗丹明6G磁性分子印迹聚合物(Fe3O4@MIPs),对合成条件进行了优化。分别采用红外光谱(FT-IR)、场发射扫描电镜(FESEM)、振动样品磁强分析(VSM)和热重分析(TGA)等仪器分析手段,对Fe3O4@MIPs的结构进行表征。结果表明,所制备的核-壳型磁性分子印迹聚合物具有高吸附容量及显著选择性;在外加磁场作用下Fe3O4@MIPs可快速与样品基质分离,大大提高了实验效率。Fe3O4@MIPs作为一种新型固相萃取材料,可以从样品中选择性分离和富集违规添加的罗丹明6G,可应用于食品的安全检测。     

白蛋白包覆纳米Fe3O4磁性粒子的制备与表征

目的：制备用于肿瘤靶向治疗的纳米级Fe3O4磁性粒子。方法：采用液相共沉淀法制备纳米Fe3O4颗粒,通过高温固化法使得白蛋白固化包覆磁性Fe3O4磁性粒子。结果：X-Ray衍射分析表明制得的纳米Fe3O4为反尖晶石结构,晶粒平均粒径为17．9nm;白蛋白包覆的磁性纳米粒子的平均粒径为341nm。结论：纳米Fe3O4及其白蛋白包覆的磁性粒孚可用作药物的载体,适用于肿瘤靶向治疗的进一步研究。     

原位生长法制备Fe3O4/TiO2纳米磁性复合体及其表征

采用原位生长法,以钛氧有机化合物为前驱物低温液相在磁性Fe3O4的表面直接形成纳米TiO2,制得Fe3O4/TiO2纳米磁性复合体,利用XRD、SEM、DLS、XPS和PPMS(磁性材料综合物性测量系统)对样品的结构和性能进行表征,并讨论Ti-O-Fe键的形成机理。结果表明:Fe3O4表面被锐钛型的TiO2包覆,且包覆效果良好。该磁性复合体颗粒分布均匀,平均粒径为59nm,饱和磁化强度为3.2emu/g,矫顽力为21Oe。     

Fe3O4@Au@Ag复合纳米材料的制备及SERS研究

用化学共沉淀法制备Fe3O4,用静电吸附法制备Fe3O4@Au复合磁性纳米材料,用种子生长法制备出Fe3O4@Au@Ag复合磁性纳米材料。利用紫外一可见吸收光谱研究复合磁性纳米颗粒的光谱特性,以结晶紫为探针分子检测磁性纳米颗粒的表面增强拉曼散射光谱。实验结果表明：复合磁性纳米颗粒既具有磁性又具有贵金属光谱特性;复合磁性纳米颗粒能很好地改善Fe3O4磁性纳米颗粒的表面增强拉曼散射活性。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from     

CNAS Passes APLAC's PTP Review

正The review group of Asia Pacific Laboratory Accreditation Cooperation(APLAC)carried out a 4-day peer review of the proficiency testing provider(PTP)for China National Accreditation Service for Conformity Assessment(CNAS)from July 28 to 31,2014.CNAS passed the PTP review with excellent performance.Two senior peer reviewers of APLAC made a comprehensive,rigorous and detailed review of CNAS’s PTP accreditation activities,and made the on-spot inspection of the review groups in Shanghai and Shenzhen respectively.     

新闻(英文)

正China and Greece Sign the Standardization Cooperation Agreement Witnessed by Chinese Premier Li Keqiang and Greek Prime Minister Antonis Samaras,AQSIQ Minister Zhi Shuping and ELOT Chairman and Executive Director Angelos Tolkas signed the SAC-ELOT Standardization Cooperation Agreement.The Agreement is one of the critical cooperation documents signed during Li Keqiang’s visit in Greece,encouraging China and Greece to