退火温度对ZnS/PS薄膜的晶体结构和光电性质的影响

用脉冲激光沉积法(PLD)在多孔硅(PS)衬底上生长ZnS薄膜,分别在300℃、400℃和500℃下真空退火。用X射线衍射(XRD)和扫描电子显微镜(SEM)研究了退火对ZnS薄膜的晶体结构和表面形貌的影响,并测量了ZnS/PS复合体系的光致发光(PL)谱和异质结的I-V特性曲线。研究表明,ZnS薄膜仅在28.5°附近存在着(111)方向的高度取向生长,由此判断薄膜是单晶立方结构的-βZnS。随着退火温度的升高,-βZnS的(111)衍射峰强度逐渐增大,且ZnS薄膜表面变得更加均匀致密,说明高温退火可以有效地促进晶粒的结合并改善结晶质量。ZnS/PS复合体系的PL谱中,随着退火温度升高,ZnS薄膜的自激活发光强度增大,而PS的发光强度减小,说明退火处理更有利于ZnS薄膜的发光。根据三基色叠加的原理,ZnS的蓝、绿光与PS的红光相叠加,ZnS/PS体系可以发射出较强的白光。但过高的退火温度会影响整个ZnS/PS体系的白光发射。ZnS/PS异质结的I-V特性曲线呈现出整流特性,且随着退火温度的升高其正向电流增加。     

ZnS薄膜生长温度对ZnS/PS体系结构和发光的影响

用电化学阳极氧化法制备了一定孔隙率的多孔硅(PS,Porous Silicon)样品,然后以PS为衬底用脉冲激光沉积(PLD)的方法在100℃、200℃和300℃下生长ZnS薄膜.X射线衍射(XRD)结果表明,样品都在28.5°附近有一个较强的衍射峰,对应于β-ZnS(111)晶向,说明薄膜沿该方向择优取向生长,但由于衬底PS粗糙的表面结构,衍射峰的半高全宽(FWHM)较大.随着ZnS薄膜生长温度的升高,薄膜的衍射峰强度逐渐增强.扫描电子显微镜(SEM)像显示,随着薄膜生长温度的升高,构成薄膜的纳米晶粒生长变大.室温下的光致发光(PL)谱表明,随着薄膜生长温度的升高,ZnS的发光强度增强而PS的发光强度减弱,把ZnS的蓝绿光与PS的红光叠加,在可见光区450～700 nm形成了一个较宽的光致发光谱带,呈现较强的白光发射.     

多孔硅的孔隙对硫化锌/多孔硅光电性质的影响

为了研究衬底多孔硅(PS)的孔隙对硫化锌/多孔硅(ZnS/PS)复合体系的光学性能和电学性质的影响,采用脉冲激光沉积方法在不同孔隙度的PS衬底上沉积了硫化锌薄膜。利用X射线衍射仪、扫描电子显微镜、荧光分光光度计和Ⅰ-Ⅴ特性曲线分别研究了PS衬底上ZnS薄膜的晶体结构、表面形貌和ZnS/PS复合体系的光学和电学性质。结果表明,沉积的ZnS薄膜呈立方相晶体结构,沿β-ZnS(111)晶向择优取向生长。随着衬底PS孔隙的增多,ZnS薄膜衍射峰的强度减小,且薄膜表面出现一些空洞和裂缝;在ZnS/PS复合体系的光致发光谱中,PS的发光相对于未沉积ZnS薄膜的PS有所蓝移,随着PS孔隙的增多,该蓝移量增大,而且在光谱中间550nm左右出现了一个新的绿光发射,归因于ZnS的缺陷中心发光。ZnS的蓝、绿光与PS的红光相叠加,整个ZnS/PS复合体系呈现出较强的白光发射。ZnS/PS异质结的Ⅰ-Ⅴ特性曲线呈现出与普通二极管相似的整流特性,在正向偏置下,电流密度较大,电压降较低;在反向偏置下,电流密度接近于0。随着衬底PS孔隙的增多,正向电流增大。该项研究结果为固态白光发射器件的实现奠定了基础。     

ZnS/PS复合体系的光致发光特性研究

通过电化学阳极氧化法制备了多孔硅（porous Si,PS）样品,然后用脉冲激光沉积的方法在其上沉积ZnS薄膜,并测量了ZnS/PS复合体系的光致发光谱,结果表明,在不同的激发波长（340nm,360nm,390nm）下,ZnS/PS复合体系的光致发光谱不同,ZnS和PS发光的相对（蓝/红）积分强度比值也不同;ZnS薄膜的生长温度不同（100℃,250℃,350℃）时,ZnS/PS复合体系的发光不同,随着生长温度的升高,复合体系的发光谱中,ZnS的发光增强而PS的发光减弱;衬底PS的制备电流密度不同（3mA/cm2,9mA/cm2,11mA/cm2）时,ZnS/PS复合体系的发光也有着不同的特点,在适当的PS制备电流密度条件下,把ZnS的发光与PS的发光叠加,得到了可见光区较宽的光致发光谱带（450nm～700nm）,呈现较强的白光发射。     

多孔Si/纳米ZnS复合材料发光的研究

利用脉冲激光沉积(PLD)分别在Si片和多孔Si衬底上沉积了ZnS薄膜,考察衬底对ZnS薄膜结构和发光性能的影响。X射线衍射(XRD)和扫描电镜(SEM)测量表明,两种衬底上制备的ZnS薄膜均沿立方相结构β-ZnS(111)晶向择优取向生长。多孔Si衬底上生长的ZnS薄膜表面有很多凹坑,而Si衬底上生长的ZnS薄膜表面相对比较平整。光致发光(PL)谱显示,ZnS薄膜沉积后,多孔Si的发光峰强度减小且峰位发生蓝移。根据ZnS薄膜具有较高透射率的特点,把透射出ZnS的多孔Si的橙红光和ZnS的发光叠加,多孔Si/ZnS纳米薄膜复合体系在可见光区有很强的PL现象。     

ZnS/PS复合体系的制备和性能表征

以电化学阳极氧化法制备的多孔硅（PS）为衬底,用脉冲激光沉积方法分别在200和300℃下制备了ZnS薄膜,得到ZnS/PS复合体系。利用X射线衍射仪（XRD）、扫描电子显微镜（SEM）、荧光分光光度计分别对ZnS/PS复合体系的晶体结构、形貌和光致发光（PL）特性进行了研究。XRD结果表明,制备的ZnS薄膜呈立方相晶体结构,沿β-ZnS（111）晶向择优取向生长,生长温度较高的样品的XRD衍射峰强度较大。SEM图像显示,生长温度较高的ZnS薄膜表面较致密平整。室温下的PL谱表明,沉积ZnS薄膜后,PS的发光峰发生蓝移。较高的生长温度下,ZnS的自激活发光强度较大,而PS的红光强度较低且峰位红移。根据三基色叠加的原理,ZnS的蓝绿光与PS的红光叠加在一起,ZnS/PS复合体系呈现出较强的白光发射,为固态白光发射器件的实现开辟了一条新的捷径。     

硫化锌/多孔硅体系和氧化锌/多孔硅体系的光学和电学特性比较

用脉冲激光沉积法在相同孔隙率的多孔硅(Porous Silicon, PS)衬底上生长了ZnS薄膜和ZnO薄膜,在室温下对ZnS/PS和ZnO/PS的光学和电学性质进行了比较.结果发现,ZnS/PS和ZnO/PS在可见光区450～700 nm都有一个较宽的光致发光谱带,呈现较强的白光发射,但ZnS/PS体系的白光发射性能要优于ZnO/PS体系的发光性能.从二者的I-V特性曲线来看,ZnS/PS异质结呈现出与普通二极管相似的整流特性,而ZnO/PS异质结的整流特性与普通二极管不同,其反向电流不饱和.     

持效疏水二氧化硅增透膜的制备和研究

为了制备结晶质量好的Cu掺杂ZnO薄膜,研究其结构和光学性质,采用脉冲激光沉积方法,在Si衬底上选择不同的衬底温度来制备薄膜.实验成功制得了结晶质量较好的Cu掺杂ZnO薄膜.利用X射线衍射仪、扫描电子显微镜和荧光分光光度计对样品进行了测量和分析.所制备的样品均表现出高度的c轴择优取向,衬底温度为300℃时,薄膜表面形貌均匀致密;在样品的光致发光谱中,发现样品除了在380nm附近出现紫外发光峰外,在460nm附近出现了蓝光发光峰,真正意义上实现了ZnO薄膜的蓝光发射.结果表明,衬底温度对其晶体质量有较大影响.     

不同衬底上氧化锌薄膜的金属有机化学气相沉积方法生长

氧化锌薄膜通过金属有机化学气相沉积方法生长在康宁玻璃与α-蓝宝石衬底上,研究了有关薄膜的生长质量与发光特性.通过X光衍射方法测试研究发现,不仅在以α-蓝宝石为衬底的样品中,同时,在以玻璃为衬底的样品中都发现了氧化锌(0 0 2)方向生长的尖峰,表明生长在两种衬底上的样品都是高度的C向生长.对两种样品的荧光谱研究发现,两者的紫外峰位于374 nm附近,在以α-蓝宝石为衬底的样品中,有深能级发射,但在以玻璃为衬底的样品中没有发现,表明在玻璃衬底上我们生长出了高质量的氧化锌薄膜.通过原子力显微镜,对生长在两种衬底上薄膜的表面形貌做了观察,其晶粒的大小与表面粗糙度有一定的差别,表明二者都是以柱状形式生长的.     

ZnS/PS复合体系的白光发射

用电化学方法制备了一定孔隙率的多孔硅(PS)样品,然后用脉冲激光沉积(PLD)法以多孔硅为衬底生长一层ZnS薄膜.ZnS的带隙较宽,对可见光是透明的,用适当波长的光激发,PS发射的橙红光可以透过ZnS薄膜,与ZnS的蓝绿光相叠加,得到了可见光区较宽的光致发光带,呈现较强的白光发射.用X射线衍射仪(XRD)和扫描电子显微镜(SEM)表征了ZnS薄膜的结构性质.结果表明,沉积的ZnS薄膜结晶质量较差,薄膜表面起伏不平,这是由于衬底PS的表面不平整所致.     

聚对苯撑苯并双(口恶)唑发光及其器件制备

采用光谱技术,研究了聚对苯撑苯并双(口恶)唑(PBO)溶液的光敏发光特性,并用相对法估算出溶液发光效率在50%范围.结合光谱技术、半导体电学和电化学等研究手段,具体研究了以PBO为发光层的单层电致发光器件,研究结果显示,电致发光与薄膜的光致发光有具有相同的发光中心,峰值位于510 nm左右.同时发现,由于存制备过程中不同处理条件使得不同厚度薄膜残留的掺杂物质浓度不同,从而引起薄膜的导电性的不同.使得器件的阈值场强随PBO厚度的减小而逐渐增加.     

系统级封装新型埋入式电源滤波结构的研究

在高密度小尺寸的系统级封装(SiP)中,对供电系统的完整性要求越来越高,多芯片共用一个电源网路所产生的电压抖动除了会影响到芯片的正常工作,还会通过供电网路干扰到临近电路和其他敏感电路,导致芯片误动作,以及信号完整性和其他电磁干扰问题.这种电压抖动所占频带相当宽,几百MHz到几个GHz的中频电源噪声普通方法很难去除.结合埋入式电容和电源分割方法的特点,提出一种新型高性能埋入式电源低通滤波结构直接替代电源/地平面.研究表明,在0.65～4GHz的频带内隔离深度可达-40～75 dB,电源阻抗均在0.25ohm以下,实现了宽频高隔离度的高性能滤波作用.分别用电磁场和广义传输线两种仿真器模拟,高频等效电路模型分析这种低通滤波器的工作原理以及结构对隔离性能的影响,并进行了实验验证.     

Emerging interconnects: a state-of-the-art review and emerging solutions

Aluminium was a primary material for interconnection in integrated circuits (ICs) since their inception. Later, copper was introduced as interconnect material which has better metallic conductivity and resistance to electromigration. As the aggressive technology scaling continues, the copper resistivity increased because of size effects, which causes increase in delay, power dissipation and electromigration. The need to reduce the resistor-capacitor??????? delay, dynamic power utilisation and the crosstalk commotion is as of now the fundamental main impetus behind the presentation of new materials. The purpose of this paper is to do a survey of interconnect material used in IC from introduction of ICs to till date. This paper studies and reviews new materials available for interconnect application which are optical interconnects, carbon nanotube (CNT), graphene nanoribbons (GNRs) and silicon nanowires which are alternatives to copper. While doing a survey of interconnect material, it is found that multiwalled CNTs, multilayer GNR and mixed CNT bundles are promising candidates and are ultimate choice that can strongly address the problems faced by copper but on integration basis copper would last for coming years.     

Arsenic deposition as a precursor layer on silicon (211) and (311) surfaces

We investigate the properties of arsenic (As) covered Si(211) and Si(311) surfaces by analyzing data from x-ray photoelectron spectroscopy (XPS) and low-energy electron diffraction (LEED) images. We then create a model using total surface energy calculations. It was found that both Si(211) and Si(311) had 0.68±0.08 surface As coverage. Si(211) had 0.28±0.04 Te coverage and Si(311) had 0.24±0.04 Te coverage. The Si(211) surface replaces the terrace and trench Si atoms with As for a lower surface energy, while the Si edge atoms form dimers. The Si(311) surface replaces all terrace atoms and adsorbs an As dimer every other edge site. These configurations imply an improvement in the mean migration path from the bare silicon surface by allowing the impinging atoms for the next epitaxial layer, tellurium (Te), to bind at every other pair of edge atoms, and not the step terrace sites. This would ensure a nonpolar, B-face growth.     

光子晶体微腔发光二极管

光子晶体微腔因其具有增强自发辐射、定向输出和单模工作的能力而受到广泛关注。介绍了光子晶体微腔发光二极管的基本原理、设计、特性、制作及其典型器件。     

Comparative study of maximum power point tracking techniques for hybrid renewable energy system

The power generation demand is increasing day-by-day throughout the world, therefore, the use of hybrid systems becomes a significant solution. The hybrid renewable energy system (HRES) is used for delivering power in various regions in order to overcome intermittence of wind and solar resources. Because of increasing environmental problems, for example, greenhouse gas emission and energy cost have interested novel research into substitute methods in favour of electrical power generation. Maximum Power Point Tracking (MPPT) control method is a vast deal of novel research used for enhancing the efficiency of HRES. The authors have revealed that the hybrid techniques i.e. Global MPPT, fuzzy-neuro systems, Adaptive Neuro-Fuzzy Inference System (ANFIS), Perturbed and Observe (P&O) + Adaptive Neural Network (ANN) etc. can provide best results as compared to other MPPT control methods. This paper offering a state of art review of MPPT control techniques for HRES.     

用于单光子TOF测量的时间-幅度变换器

基于新型共源共栅电流源的积分方法,设计了一种用于单光子飞行时间(TOF)测量的时间-幅度变换器(TAC)。该方法有效简化了TAC电路结构,减小了TAC占用面积,显著提高了TOF的满量程范围(FSR)。采用0.18 μm标准CMOS工艺设计。集成TAC的单光子探测器像素单元的填充因子可达到26.8%。后仿真结果表明,该TAC在120 ns的FSR内具有230 ps的定时分辨率,微分非线性(DNL)低于0.05 LSB,积分非线性(INL)低于1.1 LSB。蒙特卡洛仿真表明,512个TAC像素间的不均匀性低于0.5 %。该TAC非常适用于高密度时间相关的单光子计数(TCSPC)探测器阵列。     

超宽带脉冲信号的光学生成方法研究

近年来超宽带(UWB)通信技术迅猛发展,在测量、雷达技术、民用和军事无线通信中有着重要的应用,UWB-over-fiber技术已经成为目前研究的热点,其中就包括UWB脉冲信号的产生方法。区别于传统的电子学方法,光子学产生方法不受电子瓶颈制约,可以实现很高的带宽,并且具有抗电磁干扰、重量轻、结构紧凑的优点。通过对比国内外本领域研究成果,讨论及总结了以下三种原理的UWB脉冲信号的光学生成方法:1)相位调制-强度调制转换(PM-IM);2)半导体光放大器(SOA)的非线性效应;3)频谱塑形和色散所致频域-时域映射,然后对各种方案进行了对比分析。     

Joint estimation of TOA and DOA in IR-UWB system using a successive propagator method

Impulse radio ultra-wideband (IR-UWB) ranging and positioning require accurate estimation of time-of-arrival (TOA) and direction-of-arrival (DOA). With receiver of two antennas, both of the TOA and DOA parameters can be estimated via two-dimensional (2D) propagator method (PM), in which the 2D spectral peak searching, however, renders much higher computational complexity. This paper proposes a successive PM algorithm for joint TOA and DOA estimation in IR-UWB system to avoid 2D spectral peak searching. The proposed algorithm firstly gets the initial TOA estimates in the two antennas from the propagation matrix, then utilises successively one-dimensional (1D) local searches to achieve the estimation of TOAs in the two antennas, and finally obtains the DOA estimates via the difference in the TOAs between the two antennas. The proposed algorithm, which only requires 1D local searches, can avoid the high computational cost in 2D-PM algorithm. Furthermore, the proposed algorithm can obtain automatically paired parameters and has better joint TOA and DOA estimation performance than conventional PM algorithm, estimation of signal parameters via rotational invariance techniques algorithm and matrix pencil algorithm. Meanwhile, it has very close parameter estimation to that of 2D-PM algorithm. We have also derived the mean square error of TOA and DOA estimation of the proposed algorithm and the Cramer-Rao bound of TOA and DOA estimation in this paper. The simulation results verify the usefulness of the proposed algorithm.     

多孔硅发光机制的分析

从量子力学的基本理论出发讨论了量子限制效应，推导出多孔硅有效禁带宽度增量并用量子限制效应和表面态及其物质在发光中作用的理论解释了ＰＳ光致发光的实验现象。