Radiation synthesis and characterization of styrene/acrylic acid/organophilic montmorillonite hybrid nanocomposite for sorption of dyes from aqueous solutions

Organophilic montmorillonite (OMMT) was synthesized by cationic exchange reaction of Na⁺‐MMT and vinyl benzyl triethyl ammonium chloride (VBTAC) as a reactive organic modifier in an aqueous solution. A series of styrene (St)/acrylic acid (AA)/OMMT nanocomposite hydrogel containing different wt% of OMMT was synthesized through in situ polymerization using γ‐ray. The samples were characterized using Fourier transform infrared (FTIR), X‐ray powder diffraction (XRD), and transmission electron microscope (TEM), whereas thermal stability was examined by thermogravimetric analysis (TGA). The adsorption capacity and rate for both Acid Green B (anionic) and Maxilon C.I. Basic (cationic) dye including adsorption kinetics and isotherm were investigated at 30°C. TEM measurements showed spherical nanosized particles of average diameter 30–40 nm and XRD suggested the formation of exfoliated nanocomposite. TGA measurements showed that the addition of OMMT did not enhance the thermal stability where the onset temperature of the degradation for all samples was around 125°C. The effect of some important parameters on dye adsorption such as solution pH, initial dye concentration, and contact time was investigated. The equilibrium data obtained in batch experiments were correlated to Langmuir and Freundlich isotherm equations. Results showed that the adsorption of Acid Green B fitted well to the Langmuir model while the adsorption pattern of Maxilon C.I. Basic followed the Freundlich isotherm, which suggests heterogeneity of the adsorption sites on the nanocomposite. POLYM. COMPOS., 35:2353–2364, 2014. © 2014 Society of Plastics Engineers     

Application of response surface methodology for modeling of reactive dye removal from solution using starch‐montmorillonite/polyaniline nanocomposite

In this study, starch‐montmorillonite/polyaniline (St‐MMT/PANI) nanocomposite was synthesized by chemical oxidative polymerization of aniline in the presence of St‐MMT nanocomposite dispersion. The prepared ternary nanocomposite was characterized using FTIR, XRD, and SEM techniques. Adsorption properties of the nanocomposite were investigated for removal of reactive blue (RB 194) as a model reactive dye from aqueous solution. Response surface methodology was employed for the modeling of adsorption capacity of the nanocomposite. A second‐order empirical relationship between adsorption capacity and independent variables (initial dye concentration, amount of the nanocomposite, and pH of the solution) was obtained. Pareto analysis for identification of the factors effect on the system revealed that initial dye concentration was the most effective parameter. The adsorption capacity value of reactive dye on St‐MMT/PANI nanocomposite was 91.74 mg g^?1. Further investigations indicated that the adsorption experimental data were well fitted to the Langmuir isotherm and pseudo‐second‐order kinetic model. POLYM. ENG. SCI., 54:1595–1607, 2014. © 2013 Society of Plastics Engineers     

Synthesis of magnetic citric‐acid‐functionalized graphene oxide and its application in the removal of methylene blue from contaminated water

A magnetic nanocomposite of citric‐acid‐functionalized graphene oxide was prepared by an easy method. First, citric acid (CA) was covalently attached to acyl‐chloride‐functionalized graphene oxide (GO). Then, Fe₃O₄ magnetic nanoparticles (MNPs) were chemically deposited onto the resulting adsorbent. CA, as a good stabilizer for MNPs, was covalently attached to the GO; thus MNPs were adsorbed much more strongly to this framework and subsequent leaching decreased and less agglomeration occurred. The attachment of CA onto GO and the formation of the hybrid were confirmed by Fourier transform infrared spectroscopy, scanning electron microscopy, X‐ray diffraction spectrometry and transmission electron microscopy. The specific saturation magnetization of the magnetic CA‐grafted GO (GO‐CA‐Fe₃O₄) was 57.8 emu g^?1 and the average size of the nanoparticles was found to be 25 nm by transmission electron microscopy. The magnetic nanocomposite was employed as an adsorbent of methylene blue from contaminated water. The adsorption tests demonstrated that it took only 30 min to attain equilibrium. The adsorption capacity in the concentration range studied was 112 mg g^?1. The GO‐CA‐Fe₃O₄ nanocomposite was easily manipulated in an external magnetic field which eases the separation and leads to the removal of dyes. Thus the prepared nanocomposite has great potential in removing organic dyes. © 2014 Society of Chemical Industry     

Novel magnetic nanoparticles for the hydrolysis of starch with Bacillus licheniformis α‐amylase

Novel magnetic nanoparticles with an average size of 350–400 nm with N‐methacryloyl‐(L )‐phenylalanine (MAPA) as a hydrophobic monomer were prepared by the surfactant‐free emulsion polymerization of 2‐hydroxyethyl methacrylate, MAPA, and magnetite in an aqueous dispersion medium. MAPA was synthesized from methacryloyl chloride and L ‐phenylalanine methyl ester. The specific surface area of the nonporous magnetic nanoparticles was found to be 580 m²/g. Magnetic poly[2‐hydroxyethyl methacrylate–N‐methacryloyl‐(L )‐phenylalanine] nanoparticles were characterized by Fourier transform infrared spectroscopy, electron spin resonance, atomic force microscopy, and transmission electron microscopy. Elemental analysis of MAPA for nitrogen was estimated as 4.3 × 10^?3 mmol/g of nanoparticles. Then, magnetic nano‐poly[2‐hydroxyethyl methacrylate–N‐methacryloyl‐(L )‐phenylalanine] nanoparticles were used in the adsorption of Bacillus licheniformis α‐amylase in a batch system. With an optimized adsorption protocol, a very high loading of 705 mg of enzyme/g nanoparticles was obtained. The adsorption phenomena appeared to follow a typical Langmuir isotherm. The inverse of enzyme affinity for free amylase (181.82 mg/mL) was higher than that for immobilized enzyme (81.97 mg/mL). Storage stability was found to increase with adsorption. It was observed that the enzyme could be repeatedly adsorbed and desorbed without a significant loss in the adsorption amount or enzyme activity. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Magnetic and K+-cross-linked kappa-carrageenan nanocomposite beads and adsorption of crystal violet

Biopolymer-based magnetic beads, composed of kappa-carrageenan (κ-Car) and Fe₃O₄ nanoparticles, were synthesized. The magnetic beads were prepared through in situ precipitation of Fe²⁺/Fe³⁺ ions in the presence of carrageenan and subsequently treating with K⁺ solution. The structure of magnetic kappa-carrageenan beads (mκ-Carb) was characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), vibrating sample magnetometer, and thermal gravimetric analysis techniques. According to SEM micrographs, an undulant and coarse structure with cubic-shaped sections was obtained when the magnetic nanoparticles were incorporated in composition of beads. The TEM image confirmed the formation of magnetic nanoparticles with an average size of 3–7 nm. The synthesized beads were examined as adsorbent to remove crystal violet dye from aqueous solutions. It was found that due to coarse surface, the rate of dye adsorption on magnetic beads can be improved slightly. The experimental adsorption kinetics was analyzed according to pseudo-first-order and pseudo-second-order kinetic models and the adsorption kinetics followed well the pseudo-second-order model. Isotherm adsorption data of dye on beads were modeled according to Langmuir and Freundlich isotherm models. The results revealed that the experimental data have the best fit to Langmuir isotherm model, and maximum adsorption capacity of beads for dye obtained was 84.7 mg/g. The influence of pH on the variation of adsorption capacity of beads for crystal violet was not considerable. The thermodynamic parameters indicated that the adsorption of CV dye on beads is spontaneous.     

Synthesis of Octa(maleimidophenyl) silsesquioxane–SiO2/TiO2 Hybrid Nanocomposites: Adsorption Behavior for the Removal of an Organic Methylene Blue Dye and Antimicrobial Activity against Pathogens

In this study, a sol–gel process was used to prepare hybrid nanocomposite consisting of octa(maleimidophenyl) silsesquioxane-silica/titania (maleimide–POSS (polyhedral oligomeric silsesquioxanes)–SiO₂/TiO₂) to use in methylene blue (MB) adsorption and as an antibacterial agent. The structure, surface, and morphological characteristics were confirmed through Fourier transform infrared spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and transmission electron microscopy. The optical and thermal stabilities were studied by conducting UV–visible and thermogravimetric analysis–differential scanning electron calorimetry analysis. The experimental results showed a maximum dye adsorption capacity of 92% achieved using 0.5?g of hybrid nanocomposite after 2.5?h at pH 9. We also investigated the effect that the adsorbent dosage, pH, and contact time had on the removal efficiency of the MB dye in aqueous solution. The recycling experiment showed a good adsorption capacity of the MB dye, even after five repeated cycles. Furthermore, the hybrid nanocomposite was tested against pathogenic bacteria, such as Bacillus cereus, Lactobacillus, Escherichia coli, and Pseudomonas aeruginosa. The nanocomposite was observed to be highly sensitive to E. coli, B. cereus, and P. aeruginosa, as confirmed by the size of the zone inhibition.     

Coconut (Cocos nucifera) Shell Based Activated Carbon for the Removal of Malachite Green Dye from Aqueous Solutions

The adsorption of malachite green (MG) dye using coconut shell based activated carbon (CSAC) was investigated. Operational factors such as the effect of pH, initial dye concentration, adsorbent dosage, contact time, and solution temperature on the adsorption process were studied. Solution pH strongly affected the chemistry of both the dye molecule and CSAC in solution. Optimum dye removal was obtained at pH ≥ 8.0. Equilibrium was reached in 120 minutes contact time. The Langmuir, Freundlich, and Dubinin–Radushkevich (D-R) isotherm models were used to evaluate the adsorption data. The adsorption data fitted the Langmuir model most with maximum adsorption monolayer coverage of 214.63 mg/g. Pseudo-first-order, pseudo second-order, and intraparticle diffusion models were also used to fit the experimental data. Kinetic parameters, rate constants, equilibrium sorption capacities, and related correlation coefficients, for each model were calculated and discussed. Thermodynamic parameters such as ΔG⁰, ΔH⁰, and ΔS⁰ were evaluated and it was found that the sorption process was feasible, spontaneous, and exothermic in nature. The mean free energy obtained from D-R isotherm suggests that the adsorption process follows physiosorption mechanism. The results showed that coconut shells could be employed as a low-cost precursor in activated carbon preparation for the removal of MG dye from wastewaters.     

Analysis of variations in porosity of metal crosslinked collagen matrix

The fundamental knowledge of the porous nature of crosslinked collagen matrix such as tanned leather is an aid to design appropriate chemicals for leather making. It would also help to target a particular area of matrix to improve its uniformity and other functional properties. The purpose of this study is to analyze the variations in pore sizes of chromium crosslinked collagen matrix, chrome tanned leather, from different animal species and different areas of the same species. In this study, chrome tanned leather from goat and sheep were investigated for surface area, pore size, and distribution. Thermoporometry results show that average pore radius of goat leather is around 2–30 nm and that of sheep is 2–20 nm. Nitrogen adsorption result shows that average surface area of goat (8.24 m²/g) leather is higher than sheep (6.73 m²/g), but the average pore diameter of goat (289 nm) is smaller than sheep (385 nm) leather. It has been found that more numbers of smaller pores are present in goat than sheep leather and all the leather samples including goat and sheep obeyed type‐III adsorption isotherm. Capillary flow porometry analysis gives the smallest, largest, and mean‐flow‐diameter of through‐pores. The average size of largest throat pore diameter of sheep (1313 nm) is smaller than that of goat (1385 nm) leather. In general, the pore volume distribution of sheep leather is higher than that of goat leather. Morphological analysis using scanning electron microscopy shows that pore mouth of goat is deeper than that of sheep. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40835.     

Crosslinking assisted fabrication of ultrafine poly(vinyl alcohol)/functionalized graphene electrospun nanofibers for crystal violet adsorption

This article reports the fabrication of water‐stable electrospun mats made from water‐soluble poly(vinyl alcohol) and comprising ultrafine nanofibers for a high surface area to volume ratio as required for the adsorption of crystal violet. Acid‐catalyzed crosslinking is uniquely demonstrated as a facile strategy to improve water stability and, just as importantly, fine‐tune the nanofiber size of the electrospun mats. Amine‐functionalized graphene nanoplatelets are incorporated as an adsorption performance enhancer instead of the more widely reported graphene oxide. The functionalized graphene also facilitates fabrication of the composite electrospun mats by direct mixing of the water‐dispersible graphene with the aqueous polymer solution. The enhanced adsorption performance of the polymer nanocomposite mats is explained in detail at the molecular level, while the adsorption mechanism is supported by adsorption isotherm and related kinetic data. Moreover, the adsorbent mats can be removed from the water after use with the mat integrity still maintained. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46318.     

ZnO nanoparticles dispersed poly(aniline‐co‐o‐anthranilic acid) composites: Photocatalytic reduction of Cr(VI) and Ni(II)

In this report, poly(aniline‐co‐anthranilic acid)/zinc oxide (poly(ANI‐co‐ANA)/ZnO) nanocomposites were prepared by in‐situ chemical oxidative polymerization. Transmission electron microscopy (TEM), X‐ray diffraction, Fourier transform infrared spectroscopy, and ultraviolet–visible spectroscopy measurements were used to characterize the resulting pure copolymer and nanocomposite. TEM analysis showed that the nanoparticles with a mean diameter of 15–25 nm were dispersed in the copolymer matrix. Thermogravimetric analysis indicated that the nanocomposite had a higher decomposition temperature than the pure copolymer. The conductivity measurements showed the resulting nanocomposite possessed higher conductivity as compared to the pure copolymer. Photocatalytic removal of Cr(VI) and Ni(II) from aqueous solution using as‐synthesized nanocomposite under UV‐light irradiation was studied. The reduction patterns of Cr(VI) and Ni(II) were better fitted to first‐order kinetic model. The nanocomposite was also applied as a photocatalyst for the degradation of methylene blue dye. The result revealed substantial degradation of the dye (∼82%) under UV‐light illumination. POLYM. COMPOS., 35:839–846, 2014. © 2013 Society of Plastics Engineers     

Microwave-assisted green synthesis of hybrid nanocomposite: removal of Malachite green from waste water

Gum xanthan/psyllium-based nanocomposite was prepared by microwave-assisted synthetic method for the removal of toxic Malachite green (MG) dye from aqueous solutions. The nanocomposite was prepared by in situ incorporation of the K₂Zn₃[Fe(CN)₆]·9H₂O nanoparticles into the semi-IPN matrix in the presence of ammonium persulphate and glutaraldehyde as initiator-crosslinker system. Liquid uptake efficacy of the hybrid superabsorbent was enhanced through the optimization of different reaction conditions, including APS = 0.027 mol L^?1; glutaraldehyde = 0.053 × 10^?3 mol L^?1; solvent = 8.0 mL; acrylic acid = 10.928 mol L^?1; pH 7.0; reaction time = 60 s and microwave power = 100 % and its thermal behavior was evaluated using TGA-DTG-DTA technique. Candidate nanocomposite was characterized by FTIR, SEM, XRD and UV–visible spectroscopic methods. Various optimized parameters for the efficient removal (83 %) of the Malachite green were adsorbent dose of 800 mg, 14 mg L^?1 initial dye concentration and contact time of 28 h. Further, Langmuir and Freundlich adsorption isotherms showed good applicability in adsorption process of MG onto the nanocomposite with maximum adsorption efficiency of 3.21 mg g^?1. However, for Freundlich isotherm, R ² was around 0.9947 and value of 1/n was less than 1 for the synthesized nanocomposite which indicated that the Freundlich isotherm was more favorable than Langmuir isotherm model along with its usability for wide range of dye concentrations. The nanocomposite was found to be a potential product for dye removal from waste water and could prove to be a boon for textile sector.     

Investigation of α‐iron oxide‐coated polymeric nanocomposites capacity for efficient heavy metal removal from aqueous solution

In the present study, PS@α‐Fe₂O₃ nanocomposites were prepared by chemical microemulsion polymerization approach and the ability of magnetic beads to remove Cu(II) ions from aqueous solutions in a batch media was investigated. Various physico‐chemical parameters such as pH, initial metal ion concentration, temperature, and equilibrium contact time were also studied. Adsorption mechanism of Cu²⁺ ions onto magnetic polymeric adsorbents has been investigated using Langmuir, Freundlich, Sips and Redlich–Petersen isotherms. The results demonstrated that the PS@α‐Fe₂O₃ nanocomposite is an effective adsorbent for Cu²⁺ ions removal. The Sips adsorption isotherm model (R² > 0.99) was more in consistence with the adsorption isotherm data of Cu(II) ions compared to other models and the maximum adsorbed amount of copper was 34.25 mg/g. The adsorption kinetics well fitted to a pseudo second‐order kinetic model. The thermodynamic parameters (ΔH°, ΔS°, and ΔG°) were calculated from the temperature dependent sorption isotherms, and the results suggested that copper adsorption was a spontaneous and exothermic process. POLYM. ENG. SCI., 55:2735–2742, 2015. © 2015 Society of Plastics Engineers     

Recycling of reactive dye using semi‐interpenetrating polymer network from sodium alginate and isopropyl acrylamide

A sequence of semi‐interpenetrating polymer network (semi‐IPN) were synthesized by free radical photo copolymerizing acrylic acid and isopropyl acrylamide (NIPAAm) in aqueous sodium alginate (NaAlg). Their structures (FT‐IR), thermal stability (TG/DTG), morphology (SEM), mechanical properties, reactive blue 4 (RB 4) dye adsorption (624 mg/g) and its dying characteristics, reusability of dye and adsorbent were evaluated. TG thermograms of semi‐IPN in air revealed zero order kinetics for initial step thermal degradation with an activation energy of 68.68 kJ/mol. Dye adsorption showed best fit for Langmuir adsorption isotherm and the kinetics followed pseudo‐second‐order model. The water and dye diffusion kinetics followed non‐Fickian mechanism. The changes in thermodynamic parameters namely Gibbs free energy (ΔG°), entropy (ΔS°) and enthalpy (ΔH°) indicated that the adsorption was spontaneous and exothermic process for RB 4/semi‐IPN system. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40968.     

Polyurethane–attapulgite porous material: Preparation,characterization, and application for dye adsorption

A series of polyurethane–attapulgite porous (HATT/PU) materials were prepared from polyether polyol (NJ‐330), toluene diisocyanate (TDI), acid activated attapulgite (HATT), sodium bicarbonate as foaming agent, dibutylbis (lauroyloxy) tin (DBLT) as catalyst and silicon oil as stabilizer by foaming technique. The materials were characterized by FTIR, XRD and SEM. The polyurethane–attapulgite porous material as adsorbent was applied to malachite green (MG) dye wastewater treatment. Effects of attapulgite content, time, temperature, pH, and adsorbent dosage have been studied. The experimental results show that the maximum adsorption efficiency occurred at an attapulgite content of 6.0%, a time of 2.5 h, a temperature of 35°C, a pH >5 and a HATT/PU dosage of 40 mg/mL. Equilibrium isotherms for the adsorption of the dye have been measured experimentally. Results were analyzed by the Freundlich and Langmuir equation and the characteristics parameters for each adsorption isotherm were determined: Gibb's free energy (ΔG°), change in enthalpy (ΔH°) and change in entropy (ΔS°) have been calculated. The results indicated that the adsorption process was spontaneously an endothermic reaction and kinetically proceeded according to the pseudo‐second‐order model. The experimental results suggest that the prepared polyurethane–attapulgite porous materials have potential application for the wastewater treatment containing MG dye. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

The adsorption behaviors of the multiple stimulus‐responsive poly(ethylene glycol)‐based hydrogels for removal of RhB dye

In this article, the multiple stimulus‐responsive organic/inorganic hybrid hydrogels by combining poly(2‐(2‐methoxyethoxy) ethyl methacrylate‐co‐oligo (ethylene glycol) methacrylate‐co‐acrylic acid) (PMOA) hydrogel with magnetic attapulgite/Fe₃O₄ (AT‐Fe₃O₄) nanoparticles were applied to the removal of Rhodamine B (RhB) dye from wastewater. The adsorption of RhB by the hydrogels was carried out under different external environmental, such as pH, temperature and magnetic‐field. The results showed that the hydrogels still possessed temperature, pH and magnetic‐field sensitivity during the adsorption process, which indicated that the adsorption could be controlled by the hydrogels responsive. The dye adsorption had a significant increment at 30°C and the removal of RhB could reach to over 95%. Besides, the low pH values were also favorable for the RhB adsorption, the removal was over 90% at pH = 4.56. Kinetic studies showed that the pseudo‐second order kinetic model well fitted the experimental data. The rate constant of adsorption was 0.0379 g/mg min. Langmuir and Freundlich isotherm models were applied to the equilibrium adsorption for describing the interaction between sorbent and adsorbate. The maximum K_L and K_F were 2.23 (L/g) and 0.87 (mg/g) at 30°C, respectively. Under the external magnetic‐field, the adsorption rate significantly increased within 250 min and the hydrogels could be separated easily from wastewater. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42244.     

Adsorption isotherms,kinetic, and desorption studies on removal of toxic metal ions from aqueous solutions by polymeric adsorbent

Adsorption of Cd(II), Co(II), and Ni(II) on aminopyridine modified poly(styrene‐alt‐maleic anhydride) crosslinked by 1,2‐diaminoethane as an ion exchange resin has been investigated in aqueous solution. Adsorption behavior of these metal ions on the resin was studied by varying the parameters such as pH (2–6), adsorbent dose (0–4.0 g/L), contact time (0–240 min), and metal ions concentration (20–300 mg/L). Adsorption percentage was increased by increasing each of these parameters. The isotherm models such as: Langmuir, Freundlich, Temkin, and Dubinin–Radushkevich were used to describe adsorption equilibrium. The results showed that the best fit was achieved with the Langmuir isotherm equation, yielding maximum adsorption capacities of 81.30, 49.02, and 76.92 mg/g for Cd(II), Co(II), and Ni(II), respectively. The pseudo‐first‐order, pseudo‐second‐order, and intra‐particle diffusion kinetics equations were used for modeling of adsorption data and it was shown that pseudo‐second‐order kinetic equation could best describe the adsorption kinetics. The intra‐particle diffusion study revealed that external diffusion might be involved in this case. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41642.     

Lead(II)‐ion removal by ethylenediaminetetraacetic acid ligand functionalized magnetic chitosan–aluminum oxide–iron oxide nanoadsorbents and microadsorbents: Equilibrium,kinetics, and thermodynamics

Novel nanosized and microsized chitosan–Al₂O₃–Fe₃O₄ (CANF and CAMF, respectively) adsorbents were functionalized with ethylenediaminetetraacetic acid (EDTA) ligands and applied to the removal of Pb(II) ions. The prepared adsorbents were characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, and Brunauer–Emmett–Teller analysis, and their adsorption potentials were investigated with Pb(II) as a target metal under various experimental conditions. Our results show that the EDTA functionalization of CANF and CAMF increased their adsorption capacities about 31.5 and 38 times, respectively. The optimum dosage obtained was 1.0 g/L for both EDTA‐functionalized adsorbents, and the maximum adsorption took place at pH = 5.3. The kinetic results revealed that the adsorption obeyed the pseudo‐second‐order model and that the pore diffusion process played a key role in the adsorption kinetics. Also, the results of equilibrium isotherms indicate the good fit of the experimental data by the Langmuir isotherm model under the studied concentration and temperature ranges, and the adsorptions of Pb(II) ions from aqueous solution followed the monolayer coverage of the adsorbents. The maximum Pb(II)‐ion adsorption capacities of EDTA–CANF and EDTA–CAMF were 160 and 157 mg/g, respectively. These metal‐loaded adsorbents could be readily recovered from aqueous solution by magnetic separation and reused. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44360.     

Removal of acidic dye from aqueous solutions using poly(DMAEMA–AMPS–HEMA) terpolymer/MMT nanocomposite hydrogels

In this study, poly(DMAEMA–AMPS–HEMA) terpolymer/montmorillonite nanocomposite hydrogels were prepared by in situ polymerization technique using 2-(N,N-dimethylamino)ethyl methacrylate (DMAEMA), 2-acrylamido-2-methlypropane sulfonic acid (AMPS), 2-hydroxyethyl methacrylate (HEMA) monomers in clay suspension media. N,N-methylenebisacrylamide (NMBA) was used as crosslinker and potassium persulfate/potassium bisulfide were used as initiator and accelerator pair. The water absorption capacities and acidic dye (indigo carmine) adsorption properties of the nanocomposite hydrogels were investigated. Adsorption properties of the hydrogels were investigated at different conditions such as different initial dye concentration and contact time. The concentrations of the dyes were determined using UV/Vis Spectrophotometer at wavelength 610 nm. Langmuir and Freundlich isotherm models were used to describe adsorption data and the results clarified that these models were the best-fit for the adsorption of indigo carmine.     

Adsorption of platinum(IV) from an aqueous solution with magnetic cellulose functionalized with thiol and amine as a nano‐active adsorbent

In this study, magnetic cellulose was prepared and then functionalized by the grafting of glycidyl methacrylate and reaction with thiourea/amine [to produce grafted magnetic cellulose with thiol/amine (GMC–N/S)]. Thus, GMC–N/S as a nano‐active adsorbent was investigated for the adsorption of Pt(IV) in a batch system. A response surface methodology was used to study the effects of four independent variables [Pt(IV) concentration, temperature, pH of the solution, and adsorbent dose] and to optimize the process conditions for the maximum adsorption of platinum(IV) from aqueous solutions by GMC–N/S. A high coefficient of determination (R² = 98.46) implied the adsorption of Pt(IV) onto the adsorbent in a valid manner, and only 1.54% of the total variable was not explained by the model. The equilibrium adsorption data were fitted to the Langmuir isotherm. The maximum monolayer adsorption capacity of the adsorbent (GMC–N/S) for Pt(IV) was determined to be 40.48 mg/g. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45361.     

Removal of textile dyes from single and ternary solutions using poly(acrylamide‐co‐N‐methylacrylamide) grafted katira gum hydrogel

A novel hydrogel poly(acrylamide‐co‐poly‐N‐methylacrylamide) grafted katira gum (KG) was synthesized via free radical copolymerization using a mixture of acrylamide and N‐methylacrylamide in presence of N,N′‐methylene‐bis‐acrylamide as a crosslinking agent. A series of hydrogels (KG‐1 to KG‐6) were prepared by varying amount of acrylamide and N‐methylacryamide. Poly‐acrylamide‐g‐katira gum (PAM‐g‐KG) and poly‐N‐methylacrylamide‐g‐katira gum (PNMA‐g‐KG) hydrogels were also prepared using same crosslinking agent. Swelling characteristics of all the prepared hydrogels in water were evaluated and the hydrogel with best swelling property (KG‐6) was identified. The hydrogel KG‐6 was characterized by FTIR, X‐ray diffractometer, and scanning electron microscopy and was used for the adsorption of textile dyes namely methylene blue (MB), malachite green (MG), and congo red (CR) from single and ternary solutions. Adsorption dynamics, kinetics, isotherm, and thermodynamics of all the prepared hydrogels were studied in the ternary dye solutions. The sorption kinetics data were fitted well to pseudo‐second order and the equilibrium adsorption data were found to follow Freundlich isotherm model. The thermodynamics studies showed that the adsorption process was spontaneous and exothermic in nature. The preferential dye adsorption by the hydrogel was followed in the order MB > MG > CR. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45958.