Dynamic mechanical properties of semi‐interpenetrating polymer network‐based on nitrile rubber and poly(methyl methacrylate‐co‐butyl acrylate)

In this article, semi‐interpenetrating polymer network (Semi‐IPNs) based on nitrile rubber (NBR) and poly(methyl methacrylate‐co‐butyl acrylate) (P(MMA‐BA)) were synthesized. The structure and damping properties of the prepared Semi‐IPNs blends were characterized and by fourier transform infrared spectrum (FTIR), dynamic mechanical analysis (DMA), scanning electron microscopy (SEM), thermogravimetric analysis (TGA/DTG), and tensile mechanical properties. The results showed that interpenetrating network based on P(MMA‐BA) and NBR was successfully obtained, which showed the improved thermal stability compared to NBR/P(MMA‐BA)‐based two‐roll mill blends. Furthermore, Semi‐IPNs showed significantly better the dynamic mechanical properties than that of the two‐roll mill system. With the increasing feed ratio of BA and MMA during the preparation of Semi‐IPNs, the loss peak position for P(MMA‐BA) in NBR/PMMA IPNs shifted to a lower temperature from 20°C to ?17°C, and when NBR in Semi‐IPNs was accounted for 40 wt %, the dynamic mechanical thermal analysis showed that much more advanced damping material with wider temperature range (?30°C < T < 80°C) as tan δ > 0.45 can be achieved. Therefore, it was expected as a promising way to obtain the excellent damping materials with good oil‐resisted properties according the Semi‐IPNs system. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40217.     

Synthesis and characterization of paraffin/TiO2‐P(MMA‐co‐BA) phase change material microcapsules for thermal energy storage

Microcapsules based on a phase changing paraffin core and modified titanium dioxide–poly(methyl methacrylate‐co‐butyl acrylate) [P(MMA‐co‐BA)] hybrid shell were prepared via a Pickering emulsion method in this study. The microcapsules exhibit an irregularly spherical morphology with the size range of 3–24 µm. The addition of BA can enhance the toughness of the brittle polymer poly(methyl methacrylate) and improve the thermal reliability of the phase change microcapsules. The ratio of BA/MMA is in the range of 0.09–0.14, and the ratio of the monomer/paraffin is varied from 0.45 to 0.60. These microcapsules exhibit a well‐defined morphology and good thermal stability. The actual core content of the microcapsules reaches 36.09%, with an encapsulation efficiency of 73.07%. Furthermore, the prepared microcapsules present the high thermal reliability for latent‐heat storage and release after 2000 thermal cycles. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46447.     

Morphologies and dynamic mechanical properties of core‐shell emulsifier‐free latexes and their copolymers for P(BA/MMA)/P(MMA/BA) and P(BA/MMA)/PSt systems in the presence of AHPS

Different poly(methyl methacrylate/n‐butyl acrylate)/poly(n‐butyl acrylate/methyl methacrylate) [P(BA/MMA)/P(MMA/BA)] and poly(n‐butyl acrylate/methyl methacrylate)/polystyrene [P(BA/MMA)/PSt] core‐shell structured latexes were prepared by emulsifier‐free emulsion polymerization in the presence of hydrophilic monomer 3‐allyloxy‐2‐hydroxyl‐propanesulfonic salt (AHPS). The particle morphologies of the final latexes and dynamic mechanical properties of the copolymers from final latexes were investigated in detail. With the addition of AHPS, a latex of stable and high‐solid content (60 wt %) was prepared. The diameters of the latex particles are ～0.26 μm for the P(BA/MMA)/P(MMA/BA) system and 0.22–0.24 μm for the P(BA/MMA)/PSt system. All copolymers from the final latexes are two‐phase structure polymers, shown as two glass transition temperatures (T_gs) on dynamic mechanical analysis spectra. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3078–3084, 2002     

Influence of compositions and polymerization processes on morphologies,molar mass distributions,and phase structures of n‐Butyl acrylate–methyl methacrylate copolymers

The target of the research is to examine influence of a polymerization process and monomer ratio on structures and compositions of phases in an emulsion copolymerization of n‐butyl acrylate (BA) and methyl methacrylate (MMA). Emulsion copolymerizations are performed using three different BA/MMA weight ratios (60%/40%, 50%/50%, and 40%/60%) and two different processes, statistical batch and seeded emulsion polymerizations. Phase structures, monomer compositions, and morphological stabilities of copolymers are investigated by differential scanning calorimetry, ¹H‐NMR, and scanning electron microscopy. Gel permeation chromatography is used to follow the changes in the molar mass distribution during syntheses. The gel content and backbiting level of end products are measured by extraction and ¹³C‐NMR, respectively. Copolymerizations give products with a bimodal molar mass distribution and three or two separate phases having different BA/MMA compositions. The morphological stability of particles decreases with the increasing BA fraction in the feed. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41467.     

Effect of the MMA content on the emulsion polymerization process and adhesive properties of poly(BA‐co‐MMA‐co‐AA) latexes

In the past work, the shear resistance of pure poly(n‐butyl acrylate) was low, even incorporation of inorganic filler, silica in the composition. It is well‐known that the copolymerization of n‐butyl acrylate (BA) with methyl methacrylate (MMA) will increase the glass transition temperature, and enhance the shear resistance of acrylic polymers. In the current work, the preparation of a series of acrylic water‐borne pressure‐sensitive adhesives (PSAs) with the controlled composition and structure for the copolymerization of BA and acrylic acid (AA) with different MMA contents, poly(BA‐co‐MMA‐co‐AA) was reported and its effects on adhesive properties of the latices were investigated. The latices of poly(BA‐co‐MMA‐co‐AA) were prepared at a solid content of 50% by two‐stage sequential emulsion polymerization, and this process consisted of a batch seed stage giving a particle diameter of 111 nm, which was then grown by the semicontinuous addition of monomers to final diameter of 303 nm. Dynamic light scattering (DLS) was used to monitor the particle diameters and proved that no new nucleation occurred during the growth stage. Copolymerization of BA with MMA raised the glass transition temperature (T_g) of the soft acrylic polymers, and had the effect of improving shear resistance, while the loop tack and peel adhesion kept relatively high. The relationship between pressure‐sensitive properties and molecular parameters, such as gel content and molecular weight, was evaluated. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and evaluation of fluorosilicone‐modified starch for protection of historic stone

Starch is sensitive to moisture and is weak to durability in the protection application to ancient relics. Therefore, two fluorosilicone‐modified starches are firstly prepared and evaluated for the protection of historic stones. The fluoro‐silicone copolymer grafted starch of P(VTMS/12FMA)‐g‐starch is synthesized by grafting copolymer of vinyltrimethoxysilane (VTMS) and dodecafluoroheptyl methacrylate (12FMA) onto starch. While the fluoro‐silicone starch latex of VTMS‐starch@P(MMA/BA/3FMA) is obtained by emulsion polymerization of VTMS primarily grafted‐starch (VTMS‐starch) with methyl methacrylate (MMA), butyl acrylate (BA) and 2,2,2‐trifluoroethyl methacrylate (3FMA). The grafting fluorosilicone copolymer onto starch improves obviously their hydrophobic and thermal properties. Comparatively, VTMS‐starch@P(MMA/BA/3FMA) film performs higher water contact angle (107°) and thermal stability (350–430°C) than p(VTMS/12FMA)‐g‐starch film (72°, 250–420°C) due to the migration of fluorine‐containing group onto the surface of film during the film formation. Therefore, VTMS‐starch@P(MMA/BA/3FMA) shows much better protective performance in water‐resistance, and salt/freeze‐thaw resistance for stone samples. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41650.     

Rheology and morphology of polypropylene in situ grafted and blended with methyl methacrylate/n‐buthylacrylate copolymer

The rheology and morphology of polypropylene (PP) modified by grafting and blending with vinyl monomers were studied in this work. The PP powder was impregnated by mixture of methyl methacrylate (MMA)/n‐buthylacrylate (n‐BA) and copolymerized with azobisisobutyronitrile (AIBN) initiator. The simultaneous grafting and blending of PP with MMA‐co‐n‐BA copolymers were performed in a corotating, 40 L/D, twin‐screw extruder in the presence of dicumyl peroxide. The Fourier transform infrared spectroscopy (FTIR) and Scanning Electron Microscopy (SEM) were used to verify the grafting level and dispersion state of MMA/n‐BA copolymer on PP matrix, respectively, and their rheological properties were studied. It is observed that MMA/n‐BA copolymer is finely dispersed in the PP matrix. In this way, PP can be grafted, blended, and simultaneously compatibilized with polar copolymers, as is seen in SEM images. The results showed that by increasing acrylate monomers grafting on to PP increased. The same trend was observed for AIBN initiator. The gel content of samples with 25% monomers showed an increased from 0.7% to 3.5% by increasing AIBN from 0.2% to 0.4%. The grafting reaction took place with chain scission of PP molecules and also cross‐linking reactions. The optimum grafting of 7.3% with lowest chain scission and cross‐linking were obtained for samples containing 15 wt% monomer and 0.3% AIBN initiator. J. VINYL ADDIT. TECHNOL., 21:290–298, 2015. © 2014 Society of Plastics Engineers     

Microfluidic assembly of uniform fluorescent microbeads from quantum‐dot‐loaded fluorine‐containing microemulsion

We report a facile strategy for fabricating fluorescent quantum dot (QD)‐loaded microbeads by means of microfluidic technology. First, a functional fluorine‐containing microemulsion was synthesized with poly[(2‐(N‐ethylperfluorobutanesulfonamido)ethyl acrylate)‐co‐(methyl methacrylate)‐co‐(butyl acrylate)] (poly(FBMA‐co‐MMA‐co‐BA)) as the core and glycidyl methacrylate (GMA) as the shell via differential microemulsion polymerization. Then, CdTe QDs capped with N‐acetyl‐l ‐cysteine (NAC) were assembled into the poly(FBMA‐co‐MMA‐co‐BA‐co‐GMA) microemulsion particles through the reaction of the epoxy group on the shell of the microemulsion and the carboxyl group of the NAC ligand capped on the QDs. Finally, fluorescent microbeads were fabricated using the CdTe QD‐loaded fluorine‐containing microemulsion as the discontinuous phase and methylsilicone oil as the continuous phase by means of a simple microfluidic device. By changing flow rate of methylsilicone oil and hybrid microemulsion system, fluorescent microbeads with adjustable sizes ranging from 290 to 420 µm were achieved. The morphology and fluorescent properties of the microbeads were thoroughly investigated using optical microscopy and fluorescence microscopy. Results showed that the fluorescent microbeads exhibited uniform size distribution and excellent fluorescence performance. © 2014 Society of Chemical Industry     

In situ preparation and properties of high‐solid‐content and low‐viscosity poly(methyl methacrylate/n‐butyl acrylate/acrylic acid)/poly(styrene/acrylic acid) composite latexes

With monodispersed poly(methyl methacrylate/n‐butyl acrylate/acrylic acid) [P(MMA/BA/AA)] seeded latex with a particle size of 485 nm and a solid content of 50 wt % as a medium, a series of stable P(MMA/BA/AA)/poly(styrene/acrylic acid) composite latexes with a high solid content (70 wt %) and low viscosities (500–1000 mPa · s when the shear rate was 21 s^?1) was prepared in situ via simple two‐step semicontinuous monomer adding technology. The coagulum ratio of polymerization was about 0.05 wt %. The particle size distribution of such latexes was bimodal, in which the large particle was about 589 nm and the small one was about 80 nm. The latexes combined good mechanical properties with good film‐forming properties. Differential scanning calorimetry showed that the corresponding latex film had a two‐phase structure. The morphology of the latex film was characterized with atomic force microscopy and scanning electron microscopy. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1815–1825, 2007     

Preparation and characterization of a foam regulator with ultra‐high molecular weight

Multistage emulsion polymerization was used to prepare ultra‐high molecular weight foam regulator of low cost, with methyl methacrylate (MMA), butyl acrylate (BA), styrene (St) as main raw materials. Ubbelohde viscometer, dynamic light scattering, infrared and raman spectra, TEM, DSC, TGA, and GPC were all used to characterize constituent and structure, morphology, and molecular weight. As a result, when the ratio of soft monomer (BA) and hard monomer (St + MMA) is 1:3, MMA:St = 4:1, potassium persulfate (KPS): 0.15%, sodium hydrogen sulfite (SHS): 0.05%, azodiisobutyronitrile (AIBN): 0.15%, divinyl benzene (DVB): 0.3%, the final product terpolymer has obvious core‐shell structure and ultra‐high molecular weight (M_w = 1,400,000). This kind of foam regulator showed improvements in the melt strength, prevention of bubble coalescence and reduction on cost when compared with the traditional. Finally, the coefficients of poly (methyl methacrylate‐butyl acrylate‐styrene) terpolymer's Mark‐Houwink equation were calculated with tetrahydrofuran (THF) solvent at 25 °C. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44479.     

Synthesis and performance characteristics of a water‐based polyacrylate microemulsion for UHMWPE fiber adhesive coating

The water‐based polyacrylate microemulsion for ultrahigh molecular weight polyethylene (UHMWPE) fibers adhesive coating was synthesized by the emulsion polymerization of methyl methacrylate (MMA), butyl acrylate (BA), acrylic acid (AA), and hydroxyethyl acrylate (HEA) in the presence of a composite of sodium lauryl sulfate (SLS), OP‐10, and n‐octyl alcohol (NOA) as the emulsifier. The effects of the mass fraction of emulsifier and the reaction time on the properties of emulsion and its membrane were investigated. When m(BA) : m(MMA) : m(AA) : m(HEA) was 50 : 50 : 3 : 10 (wt ratio) and the mass fraction of emulsifier was 13 wt % and the reaction time was 3 h at 80°C, the latex particle diameter was 30 nm tested by transmission electron microscope (TEM). The Fourier transform infrared (FTIR) spectrometer and differential scanning calorimeter (DSC) were used to characterize the chemical structure and the glass transition temperature (T_g) of microemulsion membrane. The application results showed that this microemulsion was an ideal adhesive coating for UHMWPE fibers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Transparent poly(methyl methacrylate‐co‐butyl acrylate) nanofibers

Nanofibers of n‐Butyl Acrylate/Methyl Methacrylate copolymer [P(BA‐co‐MMA)] were produced by electrospinning in this study. P(BA‐co‐MMA) was synthesized by emulsion polymerization. The structural and thermal properties of copolymers and electrospun P(BA‐co‐MMA) nanofibers were analyzed using Fourier transform infrared spectroscopy–Attenuated total reflectance (FTIR–ATR), Nuclear magnetic spectroscopy (NMR), and Differential scanning calorimetry (DSC). FTIR–ATR spectra and NMR spectrum revealed that BA and MMA had effectively participated in polymerization. The morphology of the resulting nanofibers was investigated by scanning electron microscopy, indicating that the diameters of P(BA‐co‐MMA) nanofibers were strongly dependent on the polymer solution dielectric constant, and concentration of solution and flow rate. Homogeneous electrospun P(BA‐co‐MMA) fibers as small as 390 ± 30 nm were successfully produced. The dielectric properties of polymer solution strongly affected the diameter and morphology of electrospun polymer fibers. The bending instability of the electrospinning jet increased with higher dielectric constant. The charges inside the polymer jet tended to repel each other so as to stretch and reduce the diameter of the polymer fibers by the presence of high dielectric environment of the solvent. The extent to which the choice of solvent affects the nanofiber characteristics were well illustrated in the electrospinning of [P(BA‐co‐MMA)] from solvents and mixed solvents. Nanofiber mats showed relatively high hydrophobicity with intrinsic water contact angle up to 120°. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4264–4272, 2013     

Preparation and properties of UV‐curable fluorinated polyurethane acrylates

A series of UV‐curable polyurethane acrylates (PUA0, FPUA3, FPUA6, FPUA 9 FPUA12, FPUA15, where the numbers indicate the wt % of perfluoroalkyl acrylate), were prepared from a reactive oligomer [4,4 ?‐dicyclohexymethanediisocyanate(H12MDI)/ poly(tetramethylene glycol)(PTMG)/2‐hydroxyethyl methacrylate (HEMA): 2/1/2 molar ratio, prepolymer:40 wt %] and diluents [methyl methacrylate (MMA, 20 wt %)/ isobornyl acrylate (IBOA, 40–25 wt %)/heptadecafluorodecyl methacrylate (PFA, 0–15 wt), total diluents: 60 wt %]. This study examined the effect of PFA/IBOA weight ratio on the properties of the UV‐curable polyurethane acrylates for antifouling coating materials. The as‐prepared UV‐curable coating material containing a 15 wt % PFA content in diluents (MMA/IBOA/PFA) form a heterogeneous mixture, indicating that a PFA content of approximately 15 wt % was beyond the limit of the dilution capacity of diluents for the oligomer. In the wavelength range of 400–800 nm, the UV‐cured PUA0 film sample was quite transparent (transmittance%: near 100%). On the other hand, the transmittance% of the FPUA film sample decreased markedly with increasing PFA content. XPS showed that the film‐air surface of the UV‐cured polyurethane acrylate film had a higher fluorine content than the film‐glass dish interface. As the PFA content increased from 0 to 12 wt %, the surface tension of the UV‐cured urethane acrylates decreased from 26.8 to 15.6 mN/m, whereas the water/methylene iodide contact angles of the film–air surface increased from 90.1/63.6° to 120.9/87.1°. These results suggest that the UV‐curable polyurethane acrylates containing a PFA content up to 12 wt % have strong potential as fouling‐release coating materials. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40603.     

Mechanical properties and surface morphology of photodegraded polyoxymethylene modified by a core–shell acrylate elastomer with UV stabilization

In order to improve the photostability of polyoxymethylene (POM), a core‐shell acrylate elastomer with UV stabilization, i.e. poly[(methyl methacrylate)‐(butyl acrylate)‐2‐hydroxy‐4‐(3‐methacryloxy‐2‐hydroxypropoxy)benzophenone] (core‐shell poly(MMA‐BA‐BPMA)), was added into the POM matrix using a melt‐mixing method. The effect of the modification with core‐shell poly(MMA‐BA‐BPMA) on POM was compared with that of poly(MMA‐ co ‐BA‐ co ‐BPMA) copolymer. Scanning electron microscopy, metallographic microscopy, Fourier transform infrared spectroscopy, differential scanning calorimetry, X‐ray diffraction and X‐ray photoelectron spectroscopy were employed to characterize POM blends before and after UV irradiation, and the mechanical properties of the POM blends were investigated. The results showed that core‐shell poly(MMA‐BA‐BPMA) improved well the compatibility with and toughness of the POM matrix, and its light‐stable functional groups could increase the UV resistance of POM blends. During UV aging, the impact strength and elongation at break of POM/core‐shell poly(MMA‐BA‐BPMA) blends were retained, the growth rate of surface cracks of POM was inhibited effectively by core‐shell poly(MMA‐BA‐BPMA) and the degree of photo‐oxidation of POM blend surfaces was improved to a certain extent. Compared with poly(MMA‐ co ‐BA‐ co ‐BPMA), core‐shell poly(MMA‐BA‐BPMA) had a better UV stabilization effect on the POM matrix. Our results indicate that the core‐shell acrylate elastomer with toughening and UV stabilization functions can significantly improve the long‐term UV stability of POM. Copyright © 2012 Society of Chemical Industry     

Synthesis of Bis(1H, 1H, 2H, 2H‐perfluoro‐octyl)methylenesuccinate copolymers and their application on cotton fabrics

Bis(1H, 1H, 2H, 2H‐perfluoro‐octyl)methylenesuccinate (FOM)/ethyl acrylate (EA)/methyl methacrylate (MMA) copolymer (FOME) latexes, FOM/butyl acrylate (BA)/MMA copolymer (FOMB) latexes, and FOM/octyl acrylate (OA)/MMA copolymer (FOMO) latexes were synthesized by continuous emulsion polymerization. Solution polymerization was also carried out to prepare FOMB. The influences of fluorine content and curing conditions on the surface properties of polymer films were discussed. The water and oil repellency of cotton fabrics treated with the FOM copolymers was better than that of conventional poly(fluoroalkyl acrylate)s containing the same fluorinated chain. The polymer films or the treated fabrics were characterized by Fourier transform infrared, scanning electron microscope, atomic force microscopy, thermogravimetric analysis, x‐ray photoelectron spectrometry, and wide angle x‐ray diffraction. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci, 2013     

Synthesis of phosphorus‐containing flame‐retardant antistatic copolymers and their applications in polypropylene

By adjusting the molar ratios of antistatic monomer of octyl phenol ethylene oxide acrylate (denoted as AS), rigid monomer of methyl methacrylate (denoted as MMA), and flame‐retardant monomer of 2‐(phosphoryloxymethyl oxyethylene) acrylate (denoted as FR), a series of flame‐retardant antistatic copolymers poly (octyl phenol ethylene oxide acrylate‐co‐methyl methacrylate‐co‐phosphoryloxymethyl oxyethylene acrylate) (donated as AMF) were synthesized through radical polymerization. Among the obtained copolymers, two copolymers, AMF162 (the feed molar ratio of AS, MMA, and FR as 1 : 6 : 2) and AMF1104 (the feed molar ratio of AS, MMA, and FR as 1 : 10 : 4) with different concentrations were added into polypropylene (PP) to prepare PP‐AMF162 and PP‐AMF1104 series of composites. The thermal stability, limiting oxygen index, the antistatic property, and mechanical properties of PP composites were tested and analyzed. PP‐AMF162 series composites have excellent antistatic effect. When the AMF162 content was equal to or <15 wt %, the impact strength of PP‐AMF162 composites was higher than that of pure PP. The results indicated that copolymer AMF162 was a suitable flame‐retardant and antistatic additive for PP. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41677.     

BA‐MMA‐POMA copolymer latexes prepared by using HMPS polymerizable emulsifier

BA‐MMA‐POMA copolymer latex was successfully prepared by soap‐free emulsion polymerization of 2‐(perfluoro‐(1,1‐bisisopropyl)‐2‐propenyl)oxyethyl methacrylate(POMA) with butyl acrylate(BA), methyl methacrylate (MMA) initiated by K₂S₂O₈ in the water. POMA was synthesized from the intermediate perfluoro nonene and 2‐hydroxyethyl methacrylate as the staring reactants. The structure of BA‐MMA‐POMA copolymer latex was investigated by Fourier transform infrared (FTIR). The characteristics of the film such as hydrophobicity and glass transition temperature were characterized with the contact angle and differential scanning calorimetry respectively. The influences of the amount of the fluorinated monomer and the initiator on the soap‐free emulsion polymerization and performance of the latex were studied. In addition, comparison with the latex prepared by the conventional emulsifier SDBS is investigated. Results show that the hydrophobicity and glass transition temperature (T_g) of the latex are increased when the fluorinated monomer is introduced to copolymerize with other monomers. The hydrophobicity can be improved further with heating. Compared with the latices prepared by using SDBS emulsifier, the latices prepared by using HMPS emulsifier have larger particle size, higher surface tension. However, the difference of their T_g is extremely minute. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Vi‐PDMS incorporated with protein‐based coatings designed for permeability‐enhanced applications

Functional polydimethylsiloxanes containing vinyl groups (Vi‐PDMS) were used for silicone‐based organic polymers in composites and adhesive formulations. Poly(butyl acrylate/methyl methacrylate/vinyl silicone oil)/casein–caprolactam [P(BA‐MMA‐Vi‐PDMS)/CA‐CPL] nanoparticles were prepared via emulsifier‐free polymerization. The well‐defined core–shell structure of P(BA‐MMA‐Vi‐PDMS)/CA‐CPL nanoparticles was verified by transmission electron microscopy. The results of scanning electron microscopy and contact angle measurements proved that the as‐obtained coatings exhibited porous and hydrophobic properties, which were helpful for superior water vapor permeability. By comparing the appearance of the coatings before and after adhesion analysis, the excellent adhesion strength was proved to be dominated by Vi‐PDMS. The relationship between interface morphology and properties of the resultant coatings was investigated in detail. The nucleation mechanism for this soap‐free emulsion synthesis was also proposed accordingly. These results could help in designing coatings with better surface properties and wider application. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46501.     

Preparation and properties of core–shell nanosilica/poly(methyl methacrylate–butyl acrylate–2,2,2‐trifluoroethyl methacrylate) latex

A core–shell nanosilica (nano‐SiO₂)/fluorinated acrylic copolymer latex, where nano‐SiO₂ served as the core and a copolymer of butyl acrylate, methyl methacrylate, and 2,2,2‐trifluoroethyl methacrylate (TFEMA) served as the shell, was synthesized in this study by seed emulsion polymerization. The compatibility between the core and shell was enhanced by the introduction of vinyl trimethoxysilane on the surface of nano‐SiO₂. The morphology and particle size of the nano‐SiO₂/poly(methyl methacrylate–butyl acrylate–2,2,2‐trifluoroethyl methacrylate) [P(MMA–BA–TFEMA)] core–shell latex were characterized by transmission electron microscopy. The properties and surface energy of films formed by the nano‐SiO₂/P(MMA–BA–TFEMA) latex were analyzed by Fourier transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analysis, scanning electron microscopy/energy‐dispersive X‐ray spectroscopy, and static contact angle measurement. The analyzed results indicate that the nano‐SiO₂/P(MMA–BA–TFEMA) latex presented uniform spherical core–shell particles about 45 nm in diameter. Favorable characteristics in the latex film and the lowest surface energy were obtained with 30 wt % TFEMA; this was due to the optimal migration of fluorine to the surface during film formation. The mechanical properties of the films were significantly improved by 1.0–1.5 wt % modified nano‐SiO₂. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Polyurethane‐acrylic hybrid emulsions with high acrylic/polyurethane ratios: Synthesis,characterization, and properties

Allyl polyoxyethylene ether (APEE) was used as coupling agent between polyurethane (PU) and acrylic polymer (AC) to synthesize stable waterborne polyurethane‐acrylic (PU‐AC) hybrid emulsions with high AC/PU weight ratio ranged from 45/55 to 70/30. The effect of the AC/PU weight ratio and the acrylate type including methyl methacrylate (MMA), butyl acrylate (BA) and mixture of them on the properties of the synthesized emulsions and resultant films were investigated. The research results showed that the colloidal particle of the emulsions behaved core‐shell structure, and the copolymers were not crosslinked. An increase in the AC/PU weight ratio led to an increase in the average particles size and the particle size distribution, but decrease in the viscosity of the emulsions. Meanwhile, the molecular weight distribution of the copolymers became wide, and the tensile stress, shore A hardness, storage modulus, glass transfer temperature, water resistance, and water contact angle of the resultant films increased, except that the films of PU‐BA were too soft to determine their mechanical properties. MMA and BA can provide the PU‐AC hybrid emulsions with very different properties, and which can be adjusted according to the special application. It was suggested that APEE can not only built up chemical bonds between PU and AC, but also increase the self‐emulsifying ability in the emulsion polymerization due to its hydrophilic ethylene oxide and carboxylic groups, resulting in that PU‐AC hybrid emulsions with high AC/PU ratio can be obtained by this method. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44488.