Mechanical and thermal properties of biphenyldiol formaldehyde resin/gallic acid epoxy composites enhanced by graphene oxide

In this study, the gallic acid‐based epoxy resin (GA‐ER) and alkali‐catalysed biphenyl‐4,4′‐diol formaldehyde resin (BPFR) are synthesized. Glass fibre‐reinforced GA‐ER/BPFR composites are prepared. Graphene oxide (GO) is used to improve the mechanical and thermal properties of GA‐ER/BPFR composites. Dynamic mechanical properties and thermal, mechanical, and electrical properties of the composites with different GO content are characterized. The results demonstrate that GO can enhance the mechanical and thermal properties of the composites. The glass transition temperature, T_g, of the BPFR/GA‐ER/GO composites is 20.7°C higher than the pure resin system, and the 5% weight loss temperature, T_d5, is enhanced approximately 56.6°C. When the BPFR: GA‐ER mass ratio is at 4 : 6 and GO content is 1.0–1.2 wt %, the tensile and impact strengths of composites are 60.97 MPa and 32.08 kJ/m² higher than the pure resin composites, respectively. BPFR/GA‐ER composites have better mechanical properties, and can replace common BPA epoxy resins in the fabrication of composites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42637.     

Mechanical properties of graphene nanoplatelet/epoxy composites

Because of their high‐specific stiffness, carbon‐filled epoxy composites can be used in structural components in fixed‐wing aircraft. Graphene nanoplatelets (GNPs) are short stacks of individual layers of graphite that are a newly developed, lower cost material that often increases the composite tensile modulus. In this work, researchers fabricated neat epoxy (EPON 862 with Curing Agent W) and 1–6 wt % GNP in epoxy composites. The cure cycle used for this aerospace epoxy resin was 2 h at 121°C followed by 2 h at 177°C. These materials were tested for tensile properties using typical macroscopic measurements. Nanoindentation was also used to determine modulus and creep compliance. These macroscopic results showed that the tensile modulus increased from 2.72 GPa for the neat epoxy to 3.36 GPa for 6 wt % (3.7 vol %) GNP in epoxy composite. The modulus results from nanoindentation followed this same trend. For loadings from 10 to 45 mN, the creep compliance for the neat epoxy and GNP/epoxy composites was similar. The GNP aspect ratio in the composite samples was confirmed to be similar to that of the as‐received material by using the percolation threshold measured from electrical resistivity measurements. Using this GNP aspect ratio, the two‐dimensional randomly oriented filler Halpin–Tsai model adjusted for platelet filler shape predicts the tensile modulus well for the GNP/epoxy composites. Per the authors' knowledge, mechanical properties and modeling for this GNP/epoxy system have never been reported in the open literature. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Mechanical and thermal transmission properties of carbon nanofiber‐dispersed carbon/phenolic multiscale composites

The present article reports the development and characterization of carbon nanofiber (CNF)‐incorporated carbon/phenolic multiscale composites. Vapor‐grown CNFs were dispersed homogeneously in to phenolic resin using an effective dispersion route, and carbon fabrics were subsequently impregnated with the CNF‐dispersed resin to develop carbon fiber/CNF/phenolic resin multiscale composites. Mechanical and thermal transmission properties of multiscale composites were characterized. Elastic modulus and thermal conductivity of neat carbon/phenolic and multiscale composites were predicted and compared with the experimental results. It was observed that incorporation of only 1.5 wt % CNF resulted in 10% improvement in Young's modulus, 12% increase in tensile strength, and 36% increase in thermal conductivity of carbon/phenolic composites. Fracture surface of composite samples revealed the formation of stronger fiber/matrix interface in case of multiscale composites than neat carbon/phenolic composites. Enhancement of above properties through CNF addition has been explained, and the difference between the predicted values and experimental results has been discussed. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Solvothermally reduced graphene oxide/polyimide composites: Structures and thermal and mechanical properties

Solvothermally reduced graphene oxide (SRGO)/polyimide (PI) composites were prepared by in situ polymerization. The structures and components were carefully investigated by X-ray diffraction. Thermal properties were measured by thermogravimetry and dynamic thermomechanical analysis. Mechanical properties were carefully evaluated by tensile testing and scanning electron microscopy. The SRGO/PI composites exhibit extremely high tensile strength and elastic modulus, which is 30% higher than that of pure PI film. Meanwhile, the thermal stability of SRGO/PI composites also displays an obvious enhancement. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47164.     

Probing the reinforcing mechanism of graphene and graphene oxide in natural rubber

Natural rubber (NR) containing graphene (GE) and graphene oxide (GO) were prepared by latex mixing. The in situ chemically reduction process in the latex was used to realize the conversion of GO to GE. A noticeable enhancement in tensile strength was achieved for both GO and GE filled NR systems, but GE has a better reinforcing effect than GO. The strain‐induced crystallization was evaluated by synchrotron wide‐angle X‐ray diffraction. Increased crystallinity and special strain amplification effects were observed with the addition of GE. The incorporation of GE produces a faster strain‐induced crystallization rate and a higher crystallinity compared to GO. The entanglement‐bound tube model was used to characterize the chain network structure of composites. It was found that the contribution of entanglement to the conformational constraint increases and the network molecular parameters changes with the addition of GE and GO, while GE has a more evident effect than GO. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Magnetically aligning multilayer graphene to enhance thermal conductivity of silicone rubber composites

The increasing demand for packaging materials calls for new technologies to achieve excellent thermal conductivity of polymer composites with low content of thermal conductive filler. This article prepared a kind of magnetically functionalized multilayer graphene (Fe₃O₄@MG) via electrostatic interactions, which efficiently enhanced the thermal conductivity of silicone rubber (SR) composites by the alignment of Fe₃O₄@MG in an external magnetic field. The morphology and structure of the Fe₃O₄@MG together with the thermal conductivity of corresponding Fe₃O₄@MG/SR composites were systematically investigated by SEM, TEM, XRD, elemental mapping, and thermal conductivity tester. The obtained results showed that Fe₃O₄@MG was induced to form chain-like bundles in silicone rubber matrix under the applied magnetic field, which enhanced the MG–MG interaction, and formed effective thermal pathways in the alignment direction. Furthermore, as coating mass ratio of Fe₃O₄@MG increased, the thermal conductivity of randomly oriented Fe₃O₄@MG/silicone rubber composites (R-Fe₃O₄@MG/SR) decreased gradually, whereas the through-plane thermal conductivity of vertically aligned Fe₃O₄@MG/silicone rubber composites (V-Fe₃O₄@MG/SR) increased even filled with same contents of thermal conductive filler. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47951.     

Epoxy/p‐phenylenediamine functionalized graphene oxide composites and evaluation of their fracture toughness and tensile properties

In an attempt to enhance the mechanical properties of epoxy/graphene‐based composites, the interface was engineered through the functionalization of graphene oxide (GO) sheets with p‐phenylenediamine; this resulted in p‐phenylenediamine functionalized graphene oxide (GO–pPDA). The morphology and chemical structure of the GO–pPDA sheets were studied by spectroscopic methods, thermal analysis, X‐ray diffraction, and transmission electron microscopy. The characterization results show the successful covalent functionalization of GO sheets through the formation of amide bonds. In addition, p‐phenylenediamine were polymerized on graphene sheets to form crystalline nanospheres; this resulted in a GO/poly(p‐phenylenediamine) hybrid. The mechanical properties of the epoxy/GO–pPDA composite were assessed. Although the Young's modulus showed improvement, more significant improvements were observed in the strength, fracture strain, and plane‐strain fracture toughness. These improvements were attributed to the unique microstructure and strong interface between GO–pPDA and the epoxy matrix. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43821.     

Preparation of functional reduced graphene oxide and its influence on the properties of polyimide composites

Homogeneous dispersion and strong filler–matrix interfacial interactions were vital factors for graphene for enhancing the properties of polymer composites. To improve the dispersion of graphene in the polymer matrix and enhance the interfacial interactions, graphene oxide (GO), as an important precursor of graphene, was functionalized with amine‐terminated poly(ethylene glycol) (PEG–NH₂) to prepare GO–poly(ethylene glycol) (PEG). Then, GO–PEG was further reduced to prepare modified reduced graphene oxide (rGO)–PEG with N₂H₄·H₂O. The success of the modification was confirmed by Fourier transform infrared spectroscopy, thermogravimetric analysis, and Raman spectroscopy. Different loadings of rGO–PEG were introduced into polyimide (PI) to produce composites via in situ polymerization and a thermal reduction process. The modification of PEG–NH₂ on the surface of rGO inhibited its reaggregation and improved the filler–matrix interfacial interactions. The properties of the composites were enhanced by the incorporation of rGO–PEG. With the addition of 1.0 wt % rGO–PEG, the tensile strength of PI increased by 81.5%, and the electrical conductivity increased by eight orders of magnitude. This significant improvement was attributed to the homogeneous dispersion of rGO–PEG and its strong filler–matrix interfacial interactions. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45119.     

Effects of substitution for carbon black with graphene oxide or graphene on the morphology and performance of natural rubber/carbon black composites

In this study, nanosheets including graphene oxide (GO) and reduced graphene oxide (rGO), were incorporated into natural rubber (NR), to study the effects of substituting GO or rGO for carbon black (CB) on the structure and performance of NR/CB composites. The morphological observations revealed the dispersion of CB was improved by partially substituting nanosheets for CB. The improvements in static and dynamic mechanical properties were achieved at small substitution content of GO or rGO nanosheets. With substitution of rGO nanosheets, significant improvement in flex cracking resistance was achieved. NR/CB/rGO (NRG) composites has a much lower heat build‐up value compared with NR/CB/GO (NG) composites at a high load of nanosheets. However, both GO and rGO tended to aggregate at a high concentration, which led to the poor efficiency on enhancing the dynamic properties, or even deteriorate the performance of rubber composites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41832.     

Influence of the coupling agent and graphene oxide on the thermal and mechanical behavior of tea dust–polypropylene composites

In this study, the effects of a coupling agent and additive on the physicomechanical (morphological, mechanical, thermal, and swelling) properties of tea dust (TD)–polypropylene (PP) composites were studied. TD–PP composites were prepared with untreated tea dust (UTD) and tetraethylsilane (TES)‐treated TD or silanated tea dust (STD) particles at ratios of 0:100, 10:90, 20:80, 30:70, and 40:60 w/w. Initially, TD particles were grafted by TES as a coupling agent, and these STD particles were then modified with graphene oxide (GO) as an additive to study their effects on the STD–PP composites; these were compared to the STD–PP and UTD–PP composites in accordance with a study of improvements in the mechanical properties. All of the TD–PP composites were analyzed with Fourier transform infrared spectroscopy, scanning electron microscopy, and mechanical, thermal, and physical tests. The thermal and mechanical properties of both the STD–PP and GO‐modified STD–PP composites were found to be improved as compared to those of the UTD–PP composites. So, the recycling of a large amount of TD as a waste material could be useful in the preparation of TD–PP composites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42927.     

Epoxy–graphite oxide nanocomposites: Mechanical properties

Graphite oxide (GO) produced by Hummers method was added to epoxy for strengthening purpose. Generally the E‐modulus was increased due to the GO addition; however, depending on the treatment of the GO an increase or decrease was observed for the glass transition temperature. The change in glass transition was a result of changes in the curing behavior. Addition of GO initially increased the curing speed; however, the final curing degree was lower and was dependent on the type of GO added. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43591.     

Poly(2‐hydroxyethyl acrylate) hydrogels reinforced with graphene oxide: Remarkable improvement of water diffusion and mechanical properties

A series of hybrid hydrogels of poly(2‐hydroxyethyl acrylate), PHEA, and graphene oxide, G? O, with G? O content up to 2 wt % has been prepared by in situ polymerization. Because PHEA has been used as biomaterial in various applications, has a side chain with the hydroxyl functional group and its mechanical properties are poor, it is a good candidate for reinforcement with G? O. Fourier transform (infrared) spectroscopy, atomic force microscopy, differential scanning calorimetry, the thermal, mechanical, and water sorption properties of neat PHEA and PHEA/G? O composites have been studied in order to elucidate the dispersion and interaction between both components. An increase in the water diffusion coefficient and dramatic changes in its mechanical properties are the most remarkable results. Thus, at a nanofiller load of 2 wt %, the novel materials present an increased diffusion coefficient higher than 380% and the elastic modulus is enhanced by more than 650% in dry state and by more than 100% in swollen state, both compared to neat PHEA. These results have been attributed to the excellent interaction between the matrix, PHEA, and the reinforcement, G? O, and could open the door to new applications in the field of biomaterials with higher structural requisites. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46158.     

Thermal and electrical conductivity of melt mixed polycarbonate hybrid composites co‐filled with multi‐walled carbon nanotubes and graphene nanoplatelets

In this work, we present thermoplastic nanocomposites of polycarbonate (PC) matrix with hybrid nanofillers system formed by a melt‐mixing approach. Various concentrations of multi‐walled carbon nanotubes (MWCNT) and graphene nanoplatelets (GnP) were mixed in to PC and the melt was homogenized. The nanocomposites were compression molded and characterized by different techniques. Torque dependence on the nanofiller composition increased with the presence of carbon nanotubes. The synergy of carbon nanotubes and GnP showed exponential increase of thermal conductivity, which was compared to logarithmic increase for nanocomposite with no MWCNT. Decrease of Shore A hardness at elevated loads present for all investigated nanocomposites was correlated with the expected low homogeneity caused by a low shear during melt‐mixing. Mathematical model was used to calculate elastic modulus from Shore A tests results. Vicat softening temperature (VST) showed opposite pattern for hybrid nanocomposites and for PC‐MWCNT increasing in the latter case. Electrical conductivity boost was explained by the collective effect of high nanofiller loads and synergy of MWCNT and GnP. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42536.     

Improving thermal conductivity and shear strength of carbon nanotubes/epoxy composites via thiol‐ene click reaction

This study investigates the effect of the thiol‐ene click reaction on thermal conductivity and shear strength of the epoxy composites reinforced by various silane‐functionalized hybrids of sulfhydryl‐grafted multi‐walled carbon nanotubes (SH‐MWCNTs) and vinyl‐grafted MWCNTs (CC‐MWCNTs). The results of Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, thermal gravimetric analysis (TGA), and transmission electron microscopy (TEM) show that the sulfhydryl groups and vinyl groups are successfully grafted onto the surface of MWCNTs, after treatment of MWCNT with triethoxyvinylsilane and 3‐mercaptopropyltrimethoxysilane, respectively. Scanning electron microscopy (SEM), HotDisk thermal constant analyzer (HotDisk), optical microscope, and differential scanning calorimetry (DSC) are used to characterize the resultant composites. It is demonstrated that the hybrid of 75 wt % SH‐MWCNTs and 25 wt % CC‐MWCNTs has better dispersion and stability in epoxy matrix, and shows a stronger synergistic effect in improving the thermal conductivity of epoxy composite via the thiol‐ene click reaction with 2,2′‐azobis(2‐methylpropionitrile) as thermal initiator. Furthermore, the tensile shear strength results of MWCNT/epoxy composites and the optical microscopy photographs of shear failure section indicate that the composite with the hybrid MWCNTs has higher shear strength than that with raw MWCNTs. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44579.     

Hybridizing MWCNT with nano metal oxides and TiO2 in epoxy composites: Influence on mechanical and thermal performances

In this study, the effects of multi‐walled carbon nanotubes (MWCNT), and its hybrids with iron oxide (Fe₂O₃) and copper oxide (CuO) nanoparticles on mechanical characteristics and thermal properties of epoxy binder was evaluated. Furthermore, simultaneous effects of using MWCNT with TiO₂ as pigment and CaCO₃ as filler for epoxy composites were determined. To investigate effects of nano‐ and micro‐particles on epoxy matrix, the samples were evaluated by TGA and DTA. It was found that the hybrid of MWCNT with nano metal oxides caused considerable increment in the tensile and flexural properties of epoxy samples in comparison to the single MWCNT containing samples at the same filler contents. Significant improvement in the thermal conductivity of epoxy samples was obtained by using TiO₂ pigment along with MWCNT. The TiO₂ pigment also caused considerable improvement in mechanical properties of the epoxy matrix and the MWCNT containing nanocomposite. The best mechanical and thermal properties of epoxy nanocomposites were obtained at 1.5 wt % of MWCNT and 7 wt % of TiO₂ that it should be attributed to particle network forming of the particles which cause better nano/micro dispersion and properties. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43834.     

Preparation and properties of octadecylamine modified graphene oxide/styrene‐butadiene rubber composites through an improved melt compounding method

Octadecylamine modified graphene oxide/styrene‐butadiene rubber (GO‐ODA/SBR) composites are prepared by a novel and environmental‐friendly method called “Improved melt compounding”. A GO‐ODA/ethanol paste mixture is prepared firstly, and then blended with SBR by melt compounding. GO‐ODA sheets are uniformly dispersed in SBR as confirmed by scanning electron microscope, transmission electron microscopy, and X‐ray diffraction. The interfacial interaction between GO‐ODA and SBR is weaker than that between GO and SBR, which is proved by equilibrium swelling test and dynamic mechanical analysis. GO‐ODA/SBR show more pronounced “Payne effect” than GO/SBR composites, indicating enhanced filler networks resulted from the modification of GO with ODA. GO‐ODA/SBR composite has higher tensile strength and elongation at break than SBR and GO/SBR composite. The tensile strength and elongation at break for the composite with 5 parts GO‐ODA per hundred parts of rubber increase by 208% and 172% versus neat SBR, respectively. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42907.     

Preparation of chitosan–graphene nanosheet composites with enhanced electrochemical and mechanical properties

In this study, we proposed an alternative way to produce graphene nanosheet (GNS)/chitosan (CS) composites. Graphite‐intercalating compounds (GICs) were prepared by graphite and m‐chloroperbenzion acid (M‐CPBA) as starting materials. The GNS–CS composites were produced through the mixing of the GICs into CS and the removal of impurities in the final step. X‐ray diffraction, atomic force microscopy, and transmission and scanning electron microscopy analyses showed that graphite could be effectively exfoliated by an intercalating agent (M‐CPBA) and the GNSs were homogeneously dispersed into the CS matrix. Furthermore, we demonstrated that the electrochemical behavior and mechanical properties of the GNS–CS composites were significantly improved with a low level of GNSs in CS. The redox peak current increased 509%, and the modulus and hardness of the GNS–CS composites increased by 2.7 and 0.15 GPa, respectively, when the GNSs addition was 0.6 wt %. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45104.     

Mechanical properties of carbon fiber reinforced bisphenol A dicyanate ester composites modified with multiwalled carbon nanotubes

A novel electrophoretic deposition (EPD) method was employed for grafting multiwalled carbon nanotubes (MWCNTs) on carbon fibers, which, after impregnation with bisphenol A dicyanate ester (BADCy), synergistically reinforced BADCy matrix composites (CNT‐C/BADCy). The effect of MWCNT presence on the mechanical properties of the composites was investigated. Composite tensile strength increased by 45.2% for an EPD duration of 2 min, while flexural strength exhibited a decreasing trend with EPD duration. Optical microscopy revealed that the existence of MWCNTs enhanced the fiber‐matrix interface while a large number of CNTs were observed to have pulled‐out from the matrix, a finding which explained the observed tensile strength increase in terms of energy dissipation by the specific toughening mechanism. The flexural strength decrease of the composites with CNTs as compared to specimens without nanotubes was found linked to the increased stress concentration in the BADCy matrix due to tube presence which weakens the adhesion between carbon fabrics. In a word, carbon nanotubes will enhance the micro interface and weaken the macro interface of the composites. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45100.     

Effect of flake size on thermal properties of graphene oxide/poly(methyl methacrylate) composites prepared via in situ polymerization

The effect of graphene oxide (GO) flake size on thermal properties of GO/poly(methyl methacrylate) (GO/PMMA) composites prepared via in situ polymerization was investigated. Two styles of GO sheets were synthesized from different sizes of graphite powders by modified Hummers' method and GO/PMMA composites with GO of different sizes were prepared via in situ polymerization. Transmission electron microscopy verified that GO sheets produced from large graphite powders was obviously larger than that from small graphite powders. The similar number of layers and disorder degree of two types of GO sheets were proved by X‐ray diffraction and Raman, respectively. X‐ray diffraction and scanning electron microscopy results of GO/composites proved the homogenous dispersion of both two types of GO sheets in polymer matrix. Dynamic mechanical analysis and thermogravimetric analysis results showed that large GO sheets exhibit better improvement than small GO sheets in thermal properties of the composites. Compared with neat PMMA, the glass transition temperature and decomposition temperature of the composites with large GO sheets (0.20 wt %) were increased by 15.9 and 25.9 °C, respectively. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46290.     

Decoration of graphene oxide nanosheets with amino silane‐functionalized silica nanoparticles for enhancing thermal and mechanical properties of polypropylene nanocomposites

Graphene oxide nanosheets were decorated by amino‐silane modified silica nanoparticles. An electrostatic interaction between the negative charge of oxygen‐containing groups of graphene oxide and the positive charge of amino‐silane functional groups on the surface of silica nanoparticles plays a major role for the interfacial interaction of these two materials. The hybrid material was then used as a reinforcement in polypropylene (PP) composite. The increasing tensile strength at yield, tensile, and flexural modulus of the PP composite at a graphene oxide‐ amino‐silane silica loading content of 20 wt % are about 24.81, 55.52, and 30.35%, respectively, when compared with those of PP. It is believed that GO assists the dispersion of SiO₂ nanoparticles to the polymer matrix because of its unique structure having hydrophilicity due to its oxygen functional groups and hydrophobicity owing to its backbone graphitic carbon structure. This hybrid material may also be used as the reinforcement in other polyolefins. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44382.