Few‐layer‐graphene/polycarbonate nanocomposites as dielectric and conducting material

An attempt is taken to develop a flexible and light weight polycarbonate‐based nanocomposite system which could be successfully used as a dielectric material below percolation and as conducting material beyond percolation. The nanocomposite system has been prepared by solution mixing method in which few layer graphene was incorporated as conductive filler. X‐ray diffractometry, Raman spectroscopy, transmission electron microscopy, scanning electron microscopy techniques were employed for characterization studies. The dielectric constant and conductivity were evaluated using precision impedance analyzer. Percolation threshold has been observed to occur at 3.5 wt % of few layer graphene. Dielectric constant of the nanocomposite system, in the smearing region, has been found to increase from ～3.3 (without filler) to ～70 (at 5 wt % FLG) with a dissipation factor of 0.07. The conductivity of the system was increased from 10^?9 S/cm without FLG to 10^?2 S/cm with 7 wt % of few layer graphene. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42443.     

Low dielectric and high thermal conductivity epoxy nanocomposites filled with NH2‐POSS/n‐BN hybrid fillers

Hybrid fillers of mono‐amine polyhedral oligomeric silsesquioxane/nanosized boron nitride (NH₂‐POSS/n‐BN) were performed to fabricate NH₂‐POSS/n‐BN/epoxy nanocomposites. Results revealed that the dielectric constant and dielectric loss values were decreased with the increasing addition of NH₂‐POSS obviously, but increased with the increasing addition of BN fillers. For a given loading of NH₂‐POSS (5 wt %), the thermal conductivities of NH₂‐POSS/n‐BN/epoxy nanocomposites were improved with the increasing addition of n‐BN fillers, and the thermal conductivity of the nanocomposites was 1.28 W/mK with 20 wt % n‐BN fillers. Meantime, the thermal stability of the NH₂‐POSS/n‐BN/epoxy nanocomposites was also increased with the increasing addition of n‐BN fillers. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41951.     

Thermo‐rheological properties and miscibility of linear low‐density polyethylene‐silsesquioxane nanocomposites

The influence of octakis(n‐hexadecyldimethylsiloxy)octasilsesquioxane (hdPOSS) on rheological and thermal properties of linear low‐density polyethylene was investigated. Rheological evaluations realized by two different measuring techniques (rotational and extensional rheometry) allowed to obtain a wide range of information concerning an influence of silsesquioxanes on rheological properties of polymeric matrix. The studies were complemented with Differential Scanning Calorimetry measurements. In order to evaluate the miscibility of thermoplastic matrix and hybrid organic‐inorganic nanosized filler, rheological investigations, Dynamic Mechanical Thermal Analysis and Scanning Electron Microscopy were applied. Simultaneously, based on the rheological and thermal investigations, the mechanism of interactions between polymeric matrix and silsesquioxanes was considered. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42825.     

Preparation and properties of dopamine reduced graphene oxide and its composites of epoxy

To improve the thermal and mechanical properties and further to expand its applications of epoxy in electronic packaging, reduced graphene oxide/epoxy composites have been successfully prepared, in which dopamine (DA) was used as reducing agent and modifier for graphene oxide (GO) to avoid the environmentally harmful reducing agents and address the problem of aggregation of graphene in composites. Further studies revealed that DA could effectively eliminate the labile oxygen functionality of GO and generate polydopamine functionalized graphene oxide (PDA‐GO) because DA would be oxidated and undergo the rearrangement and intermolecular cross‐linking reaction to produce polydopamine (PDA), which would improve the interfacial adhesion between GO and epoxy, and further be beneficial for the homogenous dispersion of GO in epoxy matrix. The effect of PDA‐GO on the thermal and mechanical properties of PDA‐GO/epoxy composites was also investigated, and the incorporation of PDA‐GO could increase the thermal conductivity, storage modulus, glass transition (T_g), and dielectric constant of epoxy. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39754.     

In situ polymerization of bio‐based thermosetting polyurethane/graphene oxide nanocomposites

Novel bio‐based polyurethane/graphene oxide (GO) nanocomposites have been successfully synthesized from biorenewable epoxidized soybean‐castor oil fatty acid‐based polyols with considerable improvement in mechanical and thermal properties. The GO was synthesized via a modified pressurized oxidation method, and was investigated using Raman spectra, AFM and XPS, respectively. The toughening mechanism of GO in the bio‐based polyurethane matrix was explored. The elongation at break and toughness of polyurethane were increased by 1.3 and 0.8 times with incorporation of 0.4 wt % GO, respectively. However, insignificant changes in both mechanical strength and modulus were observed by adding GO. The results from thermal analysis indicated that the GO acts as new secondary soft segments in the polyurethane which lead to a considerable decrease in the glass transition temperature and crosslink density. The SEM morphology of the fracture surface after tensile testing showed a considerable aggregation of graphene oxide at concentrations above 0.4 wt %. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41751.     

Synthesis and properties of conducting polypyrrole,polyalkylanilines, and composites of polypyrrole and poly(2‐ethylaniline)

Conducting polymers of alkylanilines, pyrrole, and their conducting composites were synthesized by oxidation polymerization. The oxidants used were KIO₃ and FeCl₃ for the polyalkylanilines and polypyrrole (PPy), respectively. Among the polyalkylanilines synthesized with KIO₃ salt, the highest conductivity was obtained with poly(2‐ethylaniline) (P2EAn) with a value of 4.10 × 10^?5 S/cm. The highest yield was obtained with poly(N‐methylaniline) with a value of 87%. We prepared the conducting composites (PPy/P2EAn and P2EAn/PPy) by changing synthesis order of P2EAn and PPy. The electrically conducting polymers were characterized by IR spectroscopy, ultraviolet–visible spectroscopy, thermogravimetric analysis, and X‐ray diffraction spectroscopy. From the results, we determined that the properties of the composites were dependent on the synthesis order of the polymers. The thermal degradation temperature of PPy was observed to be higher than that of the other polymers and composites. We determined from X‐ray results that the structures of the homopolymers and composites had amorphous regions (88–95%) and crystal regions (5–12%). From the Gouy balance magnetic measurements, we found that the polymers and composites were bipolaron conducting mechanisms. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 241–249, 2006     

Enhanced mechanical and thermal properties of biodegradable poly(butylene succinate‐co‐adipate)/graphene oxide nanocomposites via in situ polymerization

Poly(butylene succinate‐co‐butylene adipate) (PBSA)/graphene oxide (GO) nanocomposites were synthesized via in situ polymerization for the first time. Atomic force microscopy demonstrated the achievement of a single layer of GO, and transmission electron microscopy proved the homogeneous distribution of GO in the PBSA matrix. Fourier transform infrared spectroscopy results showed the successful grafting of PBSA chains onto GO. With the incorporation of 1 wt % GO, the tensile strength and flexural modulus of the PBSA were enhanced by 50 and 27%, respectively. The thermal properties characterized by differential scanning calorimetry and thermogravimetric analysis showed increases in the melting temperatures, crystallization temperatures, and thermal stability. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4075–4080, 2013     

Microwave absorption properties of double‐layer nanocomposites based on polypyrrole/natural rubber

Thin flexible double‐layer microwave absorbers have been fabricated based on polypyrrole (PP)/natural rubber (NR) nanocomposites and their reflection loss characteristics were studied in the range of 8–18 GHz. The PP‐NR matrix was prepared from PP and NR in the ratio of 15:85. The polymers used in this work not only serve as the matrix but also improve the microwave absorption properties. The first layer or impedance matching layer which is comprised of graphite, Fe₃O₄, and TiO₂ nanoparticles in PP‐NR transmits the electromagnetic (EM) wave without reflection. The second layer which is made up of PP‐NR filled with Fe₃O₄ disperses the EM wave energy. The design of a double‐layer nanocomposite is a method to match the wave impedance, enhance wave absorption ability, and broaden the absorption frequencies. In order to achieve high absorption properties, the EM parameters such as permittivity, permeability, and thickness were controlled precisely according to quarter‐wave plate. The morphology, absorption properties, scattering parameters, thermal and wetting characteristics of double‐layer nanocomposites were investigated. The minimum reflection loss (R_L) was ?32 dB at 12.1 GHz and the absorbing bandwidth in which the R_L < ?10 dB was 9 GHz for optimum specimen with 2 mm thickness. For this specimen, the contact angle was equal to 118.7° with water as the liquid. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46565.     

Electroconductive performance of polypyrrole/graphene nanocomposites synthesized through in situ emulsion polymerization

The present study demonstrates a modified in situ emulsion polymerization (EP) approach convenient for the formation of polypyrrole/graphene (PPy/GN) nanocomposites with harnessed conductivities. A series of PPy/GN nanocomposites were prepared by loading different weight percent (wt %) of GN during in situ EP of pyrrole monomer. The polymerization was carried out in the presence of dodecyl benzene sulfonic acid, which acts as an emulsifier and protonating agent. The microstructures of the nanocomposites were studied by scanning electron microscopy, transmission electron microscopy, X‐ray diffraction, Fourier transform infrared, X‐ray photoelectron spectroscopy, UV–vis spectroscopy, Raman spectroscopy, photoluminescence spectroscopy and thermogravimetric analyses. The electrical conductivities of the nanocomposite pellets pressed at different applied pressures were determined using four probe analyzer. The electrical conductivities of the nanocomposites were considerably enhanced as compared to those of the individual PPy samples pressed at the same pressures. An enhanced conductivity of 717.06 S m^?1 was observed in the sample with 5 wt % GN loading and applied pressure of 8 tons. The results of the present study signify that the addition of GN in the PPy polymer harnesses both electrical and thermal properties of the polymer. Thus, PPy/GN nanocomposites with superior properties for various semiconductor applications can be obtained through direct loading of GN during the polymerization process. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41800.     

Synthesis and electrochemical properties of graphene oxide/nanosulfur/polypyrrole ternary nanocomposite hydrogel for supercapacitors

A method for synthesizing Graphene oxide (GO)/nano‐sulfur/polypyrrole (PPy) ternary nanocomposite hydrogel is depicted. The higher surface area of GO, PPy porous structure and their excellent conductivity are utilized, and the GO hydrogel can be made easily. The products are characterized by field‐emission scanning electron microscopy (FESEM), X‐ray diffraction (XRD), Fourier transform infrared (FTIR) spectra, and electrochemical workstation. The results demonstrated that GO/nano‐S/PPy ternary nanocomposite hydrogel is successfully synthesized. The electrochemical properties are investigated by cyclic voltammetry, galvanostatic charge/discharge measurements, and cycling life in a three‐electrode system in 1M Li₂SO₄ electrolyte solution. The GO/nano‐S/PPy ternary nanocomposite hydrogel exhibit a high specific capacitance of 892.5 F g^?1 at scan rates of 5 mV s^?1 and the capacitance retain about 81.2% (594.8 F g^?1) of initial capacitance (732.5 F g^?1) after 500 cycles at a current density of 1 A g^?1. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40814.     

Capacitance properties of graphite oxide/poly(3,4‐ethylene dioxythiophene) composites

Poly(3,4‐ethylene dioxythiophene) (PEDOT) and graphite oxide (GO)/PEDOT composites (GPTs) doped with poly(sodium styrene sulfate) (PSS) were synthesized by in situ polymerization in aqueous media. The electrochemical capacitance performances of GO, PEDOT–PSS, and GPTs as electrode materials were investigated. The GPTs had a higher specific capacitance of 108 F/g than either composite constituent (11 F/g for GO and 87 F/g for PEDOT–PSS); this was attributable to its high electrical conductivity and the layer‐within/on‐layer composite structure. Such an increase demonstrated that the synergistic combination of GO and PEDOT–PSS had advantages over the sum of the individual components. On the basis of cycle‐life tests, the capacitance retention of about 78% for the GPTs compared with that of 66% for PEDOT–PSS after 1200 cycles suggested a high cycle stability of the GPTs and its potential as an electrode material for supercapacitor applications. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Electrochemical behavior of a Nafion‐membrane‐based solid‐state supercapacitor with a graphene oxide—multiwalled carbon nanotube—polypyrrole nanocomposite

In this study, we sprayed a graphene oxide–multiwalled carbon nanotube (GM) suspension in isopropyl alcohol–water onto a Nafion membrane. The electrodeposition of polypyrrole (PPy) was carried out on Nafion to complete the fabrication of a solid‐state symmetric supercapacitor. Nafion 117 membranes are used as electrolyte separators in the preparation of supercapacitors. The characterization of the symmetric supercapacitor was done by X‐ray diffraction, field emission scanning electron microscopy, and transmission electron microscopy. The electrochemical properties of the symmetric solid‐state supercapacitor were investigated by cyclic voltammetry, galvanostatic charge–discharge, and electrochemical impedance spectroscopy techniques in 1M lithium chloride. A specific capacitance of 90.4 mF/cm² (258.3 F/g¹) was obtained for the supercapacitor at a scan rate of 10 mV s^?1. Maximum energy and power densities of 10 W h/kg and 6031 W/kg were obtained for the fabricated supercapacitor. In such a symmetric configuration, the highly interconnection networks of GM–PPy provided good structure for the supercapacitor electrode, and the good interaction between PPy and GM provided fast electron‐ and charge‐transportation paths so that a high capacitance was achieved. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44926.     

Rheological,thermal, and mechanical properties of P (3HB‐co‐4HB) and P (3HB‐co‐4HB)/EVA blends

Poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) [P(3HB‐co‐4HB)] fiber and P(3HB‐co‐4HB)/EVA fiber were obtained by single screw extrusion machine. The rheology of P(3HB‐co‐4HB) and P(3HB‐co‐4HB)/EVA blends was characterized by capillary rheometer, and the chemical groups of the blends were characterized with Fourier transform infrared spectroscopy (FT‐IR). The crystallization behavior and thermal, mechanical and elastic properties of the fibers were measured by differential scanning calorimeter (DSC), thermogravimetric analyzer (TGA) and single fiber strength tester, respectively. Besides, the moisture regain and drying shrinkage rates of the fibers were tested. These results showed that P(3HB‐co‐4HB)/EVA blends have better flowability, crystallinity, and thermal stability than P(3HB‐co‐4HB) fiber. The fracture strength of the P(3HB‐co‐4HB)/EVA fiber decreases with increasing the EVA content, but the elongation at break shows the contrary tendency. The rebound resilience ratio of P(3HB‐co‐4HB)/EVA fiber reaches 100%. Both moisture regain and drying shrinkage increase first and then decrease with increasing the EVA content. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41206.     

Electrical and thermal phenomena in low-density polyethylene/carbon black composites near the percolation threshold

Low-density polyethylene (LDPE)/carbon black (CB) composites were fabricated via melt-compounding technique. The percolation threshold was found to be around 20 wt % CB, and an electrical network formed by conductive CB was proven by scanning electron microscopy investigation. Dielectric responses depicted an interfacial relaxation peak at 20 wt % CB content. LDPE/CB composites showed an electric field-dependent conductivity as and a hysteresis behavior around the percolation threshold region. The CB particles with high thermal conductivity increased the heat conductance of the LDPE/CB20 up to 56%. The dynamic mechanical analysis of the LDPE/CB composites exhibited a noticeable contribution of CB throughout the composites, increasing the storage and loss modulus. The physical interactions between CB particles in the filler network enhanced the thermal degradation of the LDPE/CB25 composite for more than 76°C. The maximum breakdown strength of the LDPE/CB composites appeared with an approximately 10% improvement for LDPE/CB5 than pure LDPE. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47043.     

Chemical synthesis,characterization, and direct‐current conductivity studies of polypyrrole/γ‐Fe2O3 composites

The in situ polymerization of pyrrole was carried out in the presence of γ‐Fe₂O₃ to synthesize polypyrrole/γ‐Fe₂O₃ composites by a chemical oxidation method. The polypyrrole/γ‐Fe₂O₃ composites were synthesized with various compositions, including 10, 20, 30, 40, and 50 wt % γ‐Fe₂O₃ in pyrrole. The polypyrrole/γ‐Fe₂O₃ composites were characterized with X‐ray diffractometry and infrared spectroscopy. The surface morphology of these composites was studied with scanning electron microscopy. The direct‐current conductivity was studied from 40 to 200°C. The dimensions of the γ‐Fe₂O₃ particles in the matrix had a greater influence on the conductivity values. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2797–2801, 2007     

Electrical ac and dc behavior of epoxy nanocomposites containing graphene oxide

This article deals with the investigation of electrical properties of epoxy‐based nanocomposites containing graphene oxide nanofillers dispersed in the polymer matrix through two‐phase extraction. Broadband dielectric spectroscopy and dc electrical conductivity as a function of electric field have been evaluated in specimens containing up to 0.5 wt % of nanofiller. Nanocomposites containing pristine graphene oxide do not show significant changes of electrical properties. On the contrary, the same materials after a proper thermal treatment at 135°C, able to provoke the in situ reduction of graphene oxide, exhibit higher permittivity and electrical conductivity, without showing large decrease of breakdown voltage. Moreover, a nonlinear behavior of the electrical conductivity is observed in the range of electric fields investigated, i.e. 2–30 kV mm^?1. A new relaxation phenomenon with a very low temperature dependence is also evidenced at high frequency in reduced graphene oxide composites, likely associated to induced polarization of electrically conductive nanoparticles. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41923.     

Electrical properties of sorbitol‐doped poly(vinyl alcohol)–poly(acrylamide‐co‐acrylic acid) polymer membranes

Solid polymer membranes from poly(vinyl alcohol) (PVA) and poly(acrylamide‐co‐acrylic acid) (PAA) with varying doping ratios of sorbitol were prepared using the solution casting method. The films were examined with Fourier transform infrared spectroscopy, thermogravimetric analysis, differential scanning calorimetry, and AC impedance spectroscopy. The impedance measurements showed that the ionic conductivity of PVA–PAA polymer membrane can be controlled by controlled doping of sorbitol within the polymer blends. The PVA–PAA–sorbitol membranes were found to exhibit excellent thermal properties and were stable for a wide temperature range (398–563K), which creates a possibility of using them as suitable polymers for device applications. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Rheological behavior and thermal properties of poly(butyl acrylate‐co‐2‐ethylhexyl acrylate)‐grafted vinyl chloride resin

The rheological behavior and thermal properties of a poly(butyl acrylate‐co‐2‐ethylhexyl acrylate) [P(BA‐EHA)]‐grafted vinyl chloride (VC) composite resin [P(BA‐EHA)/poly(vinyl chloride) (PVC)] and its materials were investigated. The rheological behavior, thermal stability, and Vicat softening temperature (VST) of P(BA‐EHA)/PVC were measured with capillary rheometry, thermal analysis, and VST testing, respectively. The effects of the P(BA‐EHA) content and the polymerization temperature of grafted VC on the rheological behavior of the composite resin were examined. The weight loss of the composite resin and its extracted remainder via heating were analyzed. The influence of the content and crosslinking degree of P(BA‐EHA) and the polymerization temperature of the grafted VC on VST of the materials was determined. The results indicated the pseudoplastic‐flow nature of the composite resin. The flow property of the modified PVC resin was improved because of the incorporation of the acrylate polymer. The molecular weight of PVC greatly influenced the flow behavior and VST of the composite resin and its materials. The flowability of the composite resin markedly increased, and the VST of its materials decreased as the polymerization temperature of the grafted VC increased. The initial degradation temperature of the composite resin increased as the P(BA‐EHA) content increased. The VST of the samples was enhanced a little as the content of the crosslinking agent increased in P(BA‐EHA). As expected, the composite resin, with good impact resistance, had better heating stability and flowability than pure PVC, whereas the VST of the material decreased little with increasing P(BA‐EHA) content. Therefore, P(BA‐EHA)/PVC resins prepared by seeded emulsion polymerization have excellent potential for widespread applications. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 419–426, 2005     

Electrical conductivity and thermal properties of poly(m‐aminophenyl acetic acid) and its copolymers with aniline

Poly(m‐aminophenyl acetic acid) was synthesized under different conditions from the respective monomer, using ammonium persulfate as oxidizing agent in both the presence and the absence of CuCl₂ in HCl(aq). Moreover, the copolymers between aniline and m‐aminophenyl acetic acid were prepared at several feed mol ratios (f₁) of aniline. Copper was introduced by the Batch method in the homo‐ and copolymers of different compositions. The polymers were characterized by FTIR and UV‐vis spectroscopy, elemental analysis, thermal analysis, and electrical conductivity. The thermal stability and the content of copper increased as the content of aniline was increased in the copolymers. Moreover, the copolymers showed a high thermal stability; at 400°C a weight loss < 10% was observed. The electrical conductivity was increased with a higher content of aniline in the copolymers, achieving semiconduction values. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1484–1492, 2003     

Synthesis,chemical, and thermoelectric properties of n‐type π‐conjugated polymer composed of 1,2,4‐triazole and pyridine rings and its metal complexes

A soluble n‐type π‐conjugated polymer ( polymer 1 ) composed of a 1,2,4‐triazole ring substituted by a 4‐n‐octylphenyl subunit at the 4‐position of the 1,2,4‐triazole ring and pyridine‐2,5‐diyl rings was synthesized by Ni(cod)₂ (cod = 1,5‐cyclooctadiene) promoted dehalogenation polycondensation of 3,5‐bis(2‐bromopyridyl)‐4‐n‐octylphenyl‐1,2,4‐triazole ( monomer 1 ). A polymer complex ( polymer‐BiCl₃ ) was synthesized by the reaction of polymer 1 with BiCl₃. The UV–vis spectrum of polymer 1 exhibited an absorption maximum (λ_max value) at a longer wavelength than that exhibited by monomer 1 revealing that its π‐conjugation system was expanded along the polymer chain. Polymer 1 was electrochemically active in film, and the electrochemical reaction was accompanied with electrochromism. Thermoelectoric properties of polymer 1 and polymer‐BiCl₃ were investigated. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39928.