Relationship between curing activation energy and free formaldehyde content in urea-formaldehyde resins

This study investigated the effect on the curing behavior, activation energy (E _a) of the curing reaction, crystalline structure, crosslinking, and free formaldehyde content of the addition of the following scavengers in urea-formaldehyde (UF) resins: medium density fiber board flour, rice husk flour, silica powder, and tannin powder. The scavenger content was 3 and 7?wt% of the UF resin solid content. The curing behavior of UF resins was monitored by differential scanning calorimetry, thermogravimetric analysis, and X-ray crystallography. The curing E _a was correlated to the free formaldehyde content of the scavenger containing UF resins. The thermal stability of the UF resins increased but the curing E _a decreased with increasing scavenger content. After curing, the crystallinity of the UF resins decreased in the presence of scavengers. The unreacted free formaldehyde content was reduced in the tannin powder containing UF resins. The degree of crosslinking affects the formaldehyde emission from wood panels bonded with UF resin. This is especially true for wood panels in service for long periods of time and exposed to high humidity conditions. Once the free formaldehyde which influences considerably the emission has disappeared, the presence of the –CH₂– groups then becomes important. Hence, an increased resin crosslinking indicates a higher concentration of –CH₂– groups present, which may hydrolyze and emit formaldehyde slowly over time.     

Urea formaldehyde resin with low formaldehyde content modified by phenol formaldehyde intermediates and properties of its bamboo particleboards

Phenol formaldehyde reaction solution (PFS) was used to synthesize urea–formaldehyde resins (PFSUF resins) with low formaldehyde content. In addition, the prepared PFSUF resins were used as adhesives to bond bamboo particleboards. Mechanical properties, fracture morphology, water absorption ratio, and dimensional stability of bamboo particleboards have been studied by tensile tests, SEM tests, water absorption analysis, and swelling ratio analysis, respectively. The results demonstrate that the main ingredient of PFS is phenol formaldehyde intermediate 2,4,6‐trimethylolphenate and proper amount of PFS can be used to reduce the formaldehyde content of UF resins effectively. The results also show that bamboo particleboards bonded with PFSUF resins exhibit better mechanical properties, water resistance, and dimensional stability than that bonded with pure UF resin. However, the results of TG and mechanical properties analysis exhibit that alternative curing agents to ammonium chloride should be studied to improve the curing properties of the PFSUF resins with low formaldehyde content. Taken together, this work provides a method of preparing environment‐friendly PFSUF resins with low phenol and low formaldehyde content and the prepared resins have potential application in wood industry. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42280.     

Effects of formaldehyde to urea mole ratio on thermal curing behavior of urea–formaldehyde resin and properties of particleboard

As a part of abating the formaldehyde emission (FE) of urea–formaldehyde (UF) resin, this study was conducted to investigate the effects of formaldehyde to urea (F/U) mole ratio on thermal curing behavior of UF resins and properties of PB bonded with them. UF resins synthesized at different F/U mole ratios (i.e., 1.6, 1.4, 1.2, and 1.0) were used for the manufacture of PB. Thermal curing behavior of these UF resins was characterized using differential scanning calorimetry (DSC). As the F/U mole ratio decreases, the gel time, onset and peak temperatures, and heat of reaction (ΔH) increased, while the activation energy (E_a) and rate constant (k) were decreased. The amount of free formaldehyde of UF resin and FE of PB prepared decreased in parallel with decreasing the F/U mole ratio. The internal bond strength, thickness swelling, and water absorption of PB was slightly deteriorated with decreasing the F/U mole ratio of UF resins used. These results indicated that as the F/U mole ratio decreased, the FE of PB was greatly reduced at the expense of the reactivity of UF resin and slight deterioration of performance of PB prepared. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1787–1792, 2006     

Hydrolytic stability of cured urea‐formaldehyde resins modified by additives

Urea‐formaldehyde (UF) resins are prone to hydrolysis that results in low‐moisture resistance and subsequent formaldehyde emission from UF resin‐bonded wood panels. This study was conducted to investigate hydrolytic stability of modified UF resins as a way of lowering the formaldehyde emission of cured UF resin. Neat UF resins with three different formaldehyde/urea (F/U) mole ratios (1.4, 1.2, and 1.0) were modified, after resin synthesis, by adding four additives such as sodium hydrosulfite, sodium bisulfite, acrylamide, and polymeric 4,4′‐diphenylmethane diisocyanate (pMDI). All additives were added to UF resins with three different F/U mole ratios before curing the resin. The hydrolytic stability of UF resins was determined by measuring the mass loss and liberated formaldehyde concentration of cured and modified UF resins after acid hydrolysis. Modified UF resins of lower F/U mole ratios of 1.0 and 1.2 showed better hydrolytic stability than the one of higher F/U mole ratio of 1.4, except the modified UF resins with pMDI. The hydrolytic stability of modified UF resins by sulfur compounds (sodium bisulfate and sodium hydrosulfite) decreased with an increase in their level. However, both acrylamide and pMDI were much more effective than two sulfur compounds in terms of hydrolytic stability of modified UF resins. These results indicated that modified UF resin of the F/U mole ratio of 1.2 by adding acrylamide was the most effective in improving the hydrolytic stability of UF resin. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Study of glycidyl ether as a new kind of modifier for urea‐formaldehyde wood adhesives

In this work, the multiepoxy functional glycidyl ether (GE) modified urea‐formaldehyde (UF) resins were synthesized via a traditional alkaline‐acid process under low formaldehyde/urea (F/U) molar ratio. The synthesized resins were characterized by ¹³C magnetic resonance spectroscopy (¹³C‐NMR), indicating that GE can effectively react with UF resins via the ring‐opening reaction of epoxy groups. Moreover, the residual epoxy groups of GE could also participate in the curing reaction of UF resins, which was verified by Fourier transform infrared spectroscopy. The storage stability of GE‐modified UF resins and the thermal degradation behavior of the synthesized resins were evaluated by using optical microrheology and thermogravimetric analysis, respectively. Meanwhile, the synthesized resins were further employed to prepare the plywood with the veneers glued. For the modification on bonding strength and formaldehyde emission of the plywood, the influences of addition method, type, and amount of GE were systematically investigated. The performance of UF adhesives were remarkably improved by the modification of GE around 20–30% (weight percentage of total urea) in the acidic condensation stage during the resin synthesis. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Curing of low level melamine‐modified urea‐formaldehyde particleboard binder resins studied with dynamic mechanical analysis (DMA)

Effects of resin formulation, catalyst, and curing temperature were studied for particleboard binder‐type urea‐formaldehyde (UF) and 6 ～ 12% melamine‐modified urea‐melamine‐formaldehyde (UMF) resins using the dynamic mechanical analysis method at 125 ～ 160°C. In general, the UF and UMF resins gelled and, after a relatively long low modulus period, rapidly vitrified. The gel times shortened as the catalyst level and resin mix time increased. The cure slope of the vitrification stage decreased as the catalyst mix time increased, perhaps because of the deleterious effects of polymer advancements incurred before curing. For UMF resins, the higher extent of polymerization effected for UF base resin in resin synthesis increased the cure slope of vitrification. The cure times taken to reach the vitrification were longer for UMF resins than UF resins and increased with increased melamine levels. The thermal stability and rigidity of cured UMF resins were higher than those of UF resins and also higher for resins with higher melamine levels, to indicate the possibility of bonding particleboard with improved bond strength and lower formaldehyde emission. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 377–389, 2005     

Differential scanning calorimetry of urea–formaldehyde adhesive resins,synthesized under different pH conditions

The purpose of this study was to investigate the effects of reaction pH conditions on thermal behavior of urea–formaldehyde (UF) resins, for the possible reduction of formaldehyde emission of particleboard bonded with them. Thermal curing properties of UF resins, synthesized at three different reaction pH conditions, such as alkaline (pH 7.5), weak acid (pH 4.5), and strong acid (pH 1.0), were characterized with multiheating rate method of differential scanning calorimetry. As heating rate increased, the onset and peak temperatures increased for all three UF resins. By contrast, the heat of reaction (ΔH) was not much changed with increasing heating rates. The activation energy (E_a) increased as the reaction pH decreased from alkaline to strong acid condition. The formaldehyde emission of particleboard was the lowest for the UF resins prepared under strong acid, whereas it showed the poorest bond strength. These results indicated that thermal curing behavior was related to chemical species, affecting the formaldehyde emission, while the poor bond strength was believed to be related to the molecular mobility of the resin used. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 422–427, 2006     

Melamine‐bridged alkyl resorcinol modified urea–formaldehyde resin for bonding hardwood plywood

A powdery product was obtained by the reaction of methylolated melamine with alkyl resorcinols to form melamine‐bridged alkyl resorcinols (MARs). The effects of the addition of this powder on the bonding strength and formaldehyde emission of urea–formaldehyde (UF) resins were investigated. Three types of UF resins with a formaldehyde/urea molar ratio of 1.3 synthesized by condensation at pH 1.0 (UF‐1.0), pH 4.5 (UF‐4.5), and pH 5.0 (UF‐5.0) were fabricated. The addition of MAR to UF‐4.5 and UF‐5.0 for bonding hardwood plywood enhanced the bonding strength and reduced formaldehyde emission. For UF‐1.0, the addition of MAR adversely affected the bonding strength. However, the UF‐1.0 resin yielded the lowest formaldehyde emission of all of the UF resins in the study. The effects of the MAR addition were related to the molecular structures of the UF resins. UF‐1.0 contained a large amount of free urea, a considerable number of urons, and a highly methylene‐linked, ring‐structured higher molecular weight fraction and had a smaller number of methylol groups. Therefore, the addition of MAR was considered to cause a shortage of the methylol groups, which in turn, led to incomplete resin curing. In contrast to UF‐1.0, UF‐5.0 contained a smaller amount of free urea and a linearly structured higher molecular weight fraction and had a larger number of methylol groups. In this case, MAR was considered to effectively react with the methylol groups to develop a three‐dimensional crosslinked polymer network to enhance the bonding strength and suppress the generation of free formaldehyde to reduce formaldehyde emission. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Influence of nanoclay on urea‐formaldehyde resins for wood adhesives and its model

The addition of small percentages of Na⁺‐montmorillonite (NaMMT) nanoclay appears to improve considerably the performance of thermosetting urea‐formaldehyde (UF) resins used as adhesives for plywood and for wood particleboard. X‐ray diffraction (XRD) studies indicated that NaMMT loses the periodic atomic structure when mixed in small proportions in the acid‐curing environment characteristic of the curing of UF resins. This can be interpreted as becoming exfoliated under such conditions. The partly crystalline structure of the ordered zones of the UF resins is maintained but at a slightly lower level. Differential scanning calorimetry (DSC) indicated that NaMMT has an accelerating effect on the curing of the UF resin. It also appears to lead to a more controlled rate of crosslinking implying a more regular hardened network. The influence of NaMMT addition was particularly noted in plywood by the increase in water resistance of the UF‐bonded panel. In the case of wood particleboard even the dry internal bond strength of the panel, a direct indication of the performance of the resin, improved with small additions of NaMMT. A hypothesis and model of the reasons why such improvement to the performance of UF resins by addition of nanoclay should occur has been presented. This is based on the application of percolation theory to the networking capability of the clay nanoplatelets. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

脲醛树脂化学构造与胶接性能、甲醛释放量及固化特性关系的研究

采用3种典型的脲醛(UF)树脂合成方法合成UF树脂,并对合成UF树脂的性能、化学构造、胶接性能、甲醛释放量及其固化历程进行了研究。揭示了UF树脂化学构造与合成方法、胶接性能、固化特性及甲醛释放量之间的相关关系,证明UF树脂的胶接性能、固化历程、甲醛释放量与UF树脂的化学构造直接相关,尤其是树脂中羟甲基含量与结合方式、亚甲基的构造对树脂性能影响最大。     

Dynamic mechanical analysis of urea formaldehyde resin modified by ammonium pentaborate as wood adhesive

Urea formaldehyde (UF) resins with varied molar ratio of formaldehyde (F) to urea (U), modified by ammonium pentaborate (APB) at different loading level, was analyzed by dynamic mechanical analysis (DMA) and evaluated via bonding properties of its glued plywood. The result indicated that a higher loading of APB made a slower gelling and improved the ΔE′ (the difference of storage modulus) of UF resin with F/U molar ratio of 1.8. Hexamethylenetetramine, generated from the ammonium ion in APB and formaldehyde in UF resin and characterized by the covalent bond connections, was considered as the main reason to improve the rigidity of the cured UF resin system. The bond strength result confirmed the DMA analysis that the addition of APB improved bonding performance of UF resin with higher F/U molar ratio such as 1.8. A specific recommendation loading level of APB was made to modify UF resins, of which 6.0 to 8.0% APB should be used to modify UF resin with F/U molar ratio of 1.8, then 6% and 4% loading level of APB to UF resin with F/U molar ratio of 1.50 and 1.25, respectively. Finally, APB was n'ot suggested to modify UF resin at F/U molar ratio less than 1.20. POLYM. COMPOS., 37:2404–2410, 2016. © 2015 Society of Plastics Engineers     

13C‐NMR, 13C‐13C gCOSY,and ESI‐MS characterization of ether‐bridged condensation products in N,N′‐dimethylurea‐formaldehyde systems

The reaction of urea with formaldehyde is the basis for the production of urea‐formaldehyde (UF) resins which are widely applied in the wood industry. The presence of ether‐bridged condensation products in the UF resin reaction system is an open question in the literature. It is addressed in the present work. The N,N′‐dimethylurea‐formaldehyde model system was studied since it is chemically similar to the UF resin reaction system but allows for a simple elucidation of all reaction products. It was analyzed by ¹³C‐NMR spectroscopy and ESI‐MS. In corresponding NMR and MS spectra, peaks due to methoxymethylenebis(dimethyl)urea and its hemiformal were observed. ¹³C‐¹³C gCOSY analysis was conducted using labeled ¹³C‐formaldehyde. The correlation spectra showed evidence for an ether‐bridged compound and mass spectra exhibited peaks agreeing with labeled methoxymethylenebis(dimethyl)urea and its hemiformal. Methoxymethylenebis(dimethyl)urea was characterized in N,N′‐dimethylurea‐formaldehyde systems in acidic and slightly basic media. As urea is very similar to N,N′‐dimethylurea, the results of this work strengthen the assumption that ether‐bridged condensation products are likely to form in UF resins. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Thermoplastic modification of urea–formaldehyde wood adhesives to improve moisture resistance

Urea–formaldehyde (UF) resins are prone to hydrolytic degradation, which limits their use to indoor applications. This study examined the modification of UF resin with various thermoplastics as a means to increase the moisture resistance of the adhesive. UF adhesives were modified in situ with various hydrophobic and hydrophilic thermoplastic formulations, using either polar or nonpolar initiators. Unmodified and modified UF resins were characterized in terms of viscosity, pH, and gel time in their prepolymer suspension state. Cured solid UF resin plaques were prepared to isolate moisture sorption effects of the cured UF resin from that of the wood component in composites, which dominates their moisture uptake. Relative crosslink density and moisture sorption tests were run on cured UF resin plaques. Results indicated that viscosity increased after modification in most cases, with higher viscosities resulting from formulations using an acidic (polar) initiator. In all cases, activation energies of the curing reactions of thermoplastic‐modified UF suspensions were lower than the unmodified UF. High relative crosslink density compared to the unmodified UF was found for one sample, which correlated well with lower overall moisture sorption. Higher relative crosslink density of cured UF resin plaques appeared to be an indicator of lower moisture uptake. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4222–4229, 2006     

Colloidal aggregation of aminoplastic polycondensation resins: Urea–formaldehyde versus melamine–formaldehyde and melamine–urea–formaldehyde resins

Colloidal particles formation followed by their clustering have been shown to be the normal way of ageing of aminoplastic resins, namely urea–formaldehyde (UF) resins, melamine–formaldehyde (MF) resins, and melamine–urea–formaldehyde (MUF) resins. Ageing or further advancement of the resin by other means such as longer condensation times causes whitening of the resin. This is a macroscopic indication of both the formation of colloidal particles and of their clustering. It eventually progresses to resins, which are mostly in colloidal, clustered state, followed much later on by a supercluster formation starting to involve the whole resin. The initial, filament‐like colloidal aggregates formed by UF resins have different appearance than the globular ones formed by MF resins. MUF resins present a short rod‐like appearance hybrid between the two. GPC has been shown to detect the existence of colloidal superaggregates in a UF resin, while smaller aggregates might not be detected at all. The star‐like structures visible in the colloidal globules of MF resins are likely to be light interference patterns of the early colloidal structures in the resins. These star‐like interference patterns become more complex with resin ageing or advancement due to the advancement of the resin to more complex aggregates, to eventually reach the stage in which filament‐like and rod‐like structures start to appear. The next step is formation of globular masses that are representative of the true start of physical gelation. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1406–1412, 2006     

Effect of microfibrillated cellulose addition on thermal properties of three grades of urea-formaldehyde resin

Three grades of liquid urea-formaldehyde (UF) resin with different formaldehyde emission levels such as super E0 (SE0), E0 and E1 were modified by adding different amounts of microfibrillated cellulose (5 wt% MFC and 95 wt% water) that had been isolated by mechanical disintegration of pulp fibers. Thermal properties of these UF resins were investigated to understand thermal curing and degradation behaviors of the modified UF resins, using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The DSC thermograms showed an exothermic curing reaction, and the curing peak temperature of modified UF resins heavily depended on the emission resin grade with an increasing order from E1, E0 to SE0. The addition of MFC suspension into the UF resins gradually increased curing peak temperature suggesting a decrease in the resin reactivity. TGA results showed three main thermal degradation temperatures for the modified UF resins except the SE0 UF resin, which had four degradation temperatures.     

Synthesis,structure, and characterization of glyoxal‐urea‐formaldehyde cocondensed resins

To decrease the formaldehyde emission of urea‐formaldehyde (UF) bonded products at source, monomethylol urea (MMU) was chosen to react with glyoxal (G), a nonvolatile and nontoxic aldehyde, to prepare a novel glyoxal‐urea‐formaldehyde (GUF) cocondensed resin. The GUF resins were synthesized with different MMU/G molar ratios, and the basic properties were tested. The GUF resins were characterized by ultraviolet‐visible spectroscopy, Fourier transform infrared spectroscopy, carbon‐13 nuclear magnetic resonance spectroscopy and matrix assisted laser desorption ionization time of flight mass spectrometry (MALDI‐TOF‐MS). The results show that the synthesized GUF resins remain stable for at least 10 days at ambient temperature. Conjugated structures, and large amounts of ? OH, ? NH? , C? N, and C?O groups with different levels of substitution exist in the GUF resin. There are two repeating motives in the MALDI‐TOF‐MS spectrum of the GUF resin, one of 175 ±1 Da and a second one of 161 ± 1 Da. Moreover, the peaks due to the dehydration condensation reaction of MMU also appear in the spectra. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41009.     

Alternative to latent catalysts for curing UF resins used in the production of low formaldehyde emission wood-based panels

This paper studies alternative catalysts to ammonium sulfate for curing urea-formaldehyde (UF) resins. When using a latent catalyst like ammonium sulfate, hexamine is formed as by-product of curing reaction. It is believed that hexamine hydrolysis may contribute to formaldehyde release during the life-time of wood-based panels produced with UF resins. Orthophosphoric acid, on the other hand, catalyzes resin cure without by-product formation and was compared to ammonium sulfate. The pot-life of adhesives with both catalysts was evaluated at 40 °C with a Brookfield rheometer. Mechanical resistance tests performed with ABES (Automated Bonding Evaluation System) showed that orthophosphoric acid effectively catalyzes UF resin cure. Particleboards were produced using both catalysts and the most important properties evaluated, according to European Standards: formaldehyde content, internal bond, moisture content, thickness swelling and density. Particleboards cured with orthophosphoric acid and stored under forceful conditions of humidity and temperature presented similar internal bond and lower formaldehyde content than those produced with ammonium sulfate.     

Effect of spent sulfite liquor on urea–formaldehyde resin performance

Combination of urea–formaldehyde (UF) resins with technical lignins has been often reported in the literature. However, the actual implications of this approach have not been effectively addressed yet. In this work, unmodified thick spent sulfite liquor (TSSL) and hydroxymethylated TSSL (TSSLH) were incorporated in a standard UF resin in different amounts (10 and 20%) and at different stages. When 10% of TSSLH was incorporated after the synthesis, the produced particleboards performed equivalently to when 90% of UF resin was used. In all other cases tested, combining UF resin with TSSL/TSSLH actually led to lower internal bond strengths. The results evidence that addition of TSSL or TSSLH does not have a beneficial effect on UF bonding performance. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47389.     

Effect of a novel environmentally friendly additive of polyaspartic acid on the properties of urea formaldehyde resins/montmorillonite

Polyaspartic acid (PASP) is a biodegradable green material with carboxyl groups ( COOH) and amido groups ( CO NH ). In the article, a novel urea-formaldehyde (UF) resin modified by PASP and Ca-montmorillonite (Ca-Mt) was prepared by the alkaline-acid-alkaline method. The synthesized materials were characterized by X-ray diffraction, Fourier transform-infrared spectroscopy, thermal analysis (TG-DTG), and scanning electron microscopy. The effects of viscosity, curing time, and free formaldehyde were investigated. The results showed that the layered structure of Ca-Mt was exfoliated and dispersed in the bulk of UF. The thermal stability of the modified UF was much better than that of pure UF resin. The percentage of free formaldehyde was declined from 26 to 18%. Meanwhile, the UF composites showed the short curing time and the optimum viscosity. Finally, a synthetic process of UF modified by PASP and Ca-Mt and a possible mechanism for immobilizing the free formaldehyde were suggested. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48038.     

Uron and uron–urea‐formaldehyde resins

The favored pH ranges for the formation of urons in urea‐formaldehyde (UF) resins preparation were determined, these being at pH's higher than 6 and lower than 4 at which the equilibrium urons ↔ N,N′‐dimethylol ureas are shifted in favor of the cyclic uron species. Shifting the pH slowly during the preparation from one favorable range to the other causes shift in the equilibrium and formation of a majority of methylol ureas species, whereas a rapid change in pH does not cause this to any great extent. UF resins in which uron constituted as much as 60% of the resin were prepared and the procedure to maximize the proportion of uron present at the end of the reaction is described. Uron was found to be present in these resins also as linked by methylene bridges to urea and other urons and also as methylol urons, the reactivity of the methylol group of this latter having been shown to be much lower than that of the same group in methylol ureas. Thermomechanical analysis (TMA) tests and tests on wood particleboard prepared with uron resins to which relatively small proportions of urea were added at the end of the reaction were capable of gelling and yielding bonds of considerable strength. Equally, mixing a uron‐rich resin with a low F/U molar ratio UF resin yielded resins of greater strength than a simple UF of corresponding molar ratio indicating that UF resins of lower formaldehyde emission with still acceptable strength could be prepared with these resins. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 277–289, 1999