Preparation of redox fibers containing hydroxy‐alkyl amino groups and their adsorptive properties toward Au(III)

Three kinds of redox fibers (fibers II, III, and IV) are prepared by amination of the reactive chloromethylated poly(vinyl acetate) grafting polystyrene‐divinylbenzene fiber (fiber I) with diethanolamine, ethanolamine, or triethanolamine. The N‐content of the fibers is 2.26, 2.71, and 1.86 mmol g⁻¹, respectively. Results of static adsorption experiments show that the adsorption amount of fibers II, III, and IV toward Au(III) reaches 550 mg g⁻¹, 620 mg g⁻¹, and 409 mg g⁻¹, respectively, between pH 2.0 and pH 3.0. Some adsorbed Au(III) can be reduced to Au(0). The reduction percentage of Au(III) adsorbed by fiber II increases with rising pH value of the solution and can be as high as 87% at pH 5.0. The amount of Au(III) adsorbed by fiber II increases with solution temperature, but decreases with ionic strength of the solution. The adsorption amount of fibers II and III toward Au(III) is less in ethanol or in acetacetate medium than in water. Kinetic adsorption data indicates that 50 min is needed for fiber II to adsorb half of its saturate adsorption amount of Au(III). It was proved by elemental analysis, infrared spectroscopy, nuclear magnetic resonance, and electron spectroscopy for chemical analysis determinations that the carbon atoms connecting with the hydroxy groups near the nitrogen atoms were easily oxidized into carbonyl ones during redox adsorption reaction of fibers II, III, and IV with Au(III). Some grains of gold adsorbed on fiber II were discovered under scanning electron microscopy. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 47–54, 1999     

Green and efficient synthesis of an adsorbent fiber by preirradiation‐induced grafting of PDMAEMA and its Au(III) adsorption and reduction performance

N ,N ‐Dimethylamino ethyl methacrylate (DMAEMA) is covalently bonded on a commercial polyethylene‐coated polypropylene skin‐core structure fiber (PE/PP) in aqueous and MeOH/H₂O solutions by a one‐step green reaction using radiation‐induced graft polymerization. The effects of the absorbed dose and solvent system on grafting yield are investigated, while the chemical and physical properties of the functionalized fiber are also evaluated. The fiber with a D_g of 51.6% exhibited good adsorption capacity of Au(III) ions over a large range of concentrations (from 10 to 2.5 g L^?1) in both batch and flow‐through adsorption tests. The highest capacity of Au was 949.3 mg g^?1. After elution, the adsorbents can be reused without any further regeneration for at least five adsorption‐desorption cycles. Additionally, the fibers show high selectivity for Au(III). The distribution coefficient of Au(III) is 10⁴ to 10⁵ times higher than that for Cu(II), Fe(III), Ni(II), and Pb(II) even at 100 times lower Au(III) concentration compared to the co‐existing metal ion concentration. This study provides an effective and novel approach for gold recovery from aqueous solutions. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44955.     

Selective Competitive Biosorption of Au(III) and Cu(II) in Binary Systems by Magnetospirillum gryphiswaldense

The biosorption of Au(III) and Cu(II) ions in both single and binary systems by Magnetospirillum gryphiswaldense (MSR-1) was investigated. For comparison with the selective reinforced competitive biosorption process in a binary system, the experimental research first explored the biosorption of Au(III) and Cu(II) in a single system under various conditions. The biomass exhibited the highest single Au(III) and Cu(II) ion adsorption yields at room temperature (25°C), pH values of 2.5 and 5.0, respectively, and a biomass concentration of 10 g · L^?1 (3.83 g · L^?1, dry basis). The experimental data from the single component system for the two metallic ions fitted well to a Langmuir isotherm and a pseudo second-order kinetic models. In the Au(III)-Cu(II) binary system, the coexistence of Cu(II) cations promoted the adsorption of Au(III) within a certain range of ratios. A new sigmoidal Cu(II) biosorption isotherm was determined specifically to reveal the Cu(II) adsorption behavior in this case.     

Structure characterization and adsorption properties of tetraethylenepentamine ion exchange fiber

A novel tetraethylenepentamine ion exchange fiber (TAIEF) was prepared using polypropylene grafted styrene (PP‐g‐ST) fiber as raw material. The chemical structure of TAIEF was characterized using infrared spectrum (IR) method. TAIEF had good appearance and shape after reaction in SEM images, the TGA curves revealed that both PP‐g‐ST fiber and acetyl PP‐g‐ST fiber had good thermal stability below 250 °C, and the weight loss rate of TAIEF is 9% from 50 °C to 200 °C obtained by TGA. TAIEF adsorption capacity to Fe(III) is larger than that of In(III) in the pH value 1.00 to 3.00, while the pH value is at 2.50 to 3.00, TAIEF adsorption capacity to Fe(II) and Zn(II) are smaller than that of In(III). The selective adsorption ability to Fe(III) is higher than In(III), and the selective absorptivity to In(III) is better than Fe(II) and Zn(II). The mechanism was explained of TAIEF favorable selective adsorption to In(III) and Fe(III) ions in mixed solutions. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44513.     

Synthesis and application of ion‐imprinted resin based on modified melamine–thiourea for selective removal of Hg(II)

A novel Hg(II) ion‐imprinted resin based on thiourea‐modified melamine was manufactured for selective elimination of Hg²⁺ from aqueous solutions. The polymerizable thiourea–melamine ligand together with its Hg(II) complex were extensively investigated using elemental analysis, Fourier transform infrared (FTIR) and ¹H NMR spectroscopies. The Hg(II) complex was used in a condensation polymerization in the presence of formaldehyde crosslinker and then the Hg(II) ions were leached out from the crosslinked polymeric network to finally leave the ion‐imprinted Hg‐PMTF resin. Both ion‐imprinted Hg‐PMTF and non‐imprinted resins were examined utilizing scanning electron microscopy and FTIR spectroscopy. The potential of the prepared resin for selective separation of Hg(II) ions from aqueous solutions was then evaluated by performing a series of batch experiments. Hg‐PMTF displayed an obvious rapid removal of Hg(II) ions with a pseudo‐second‐order kinetic pattern. In addition, the Langmuir adsorption isotherm model exhibited the best fit with the experimental data with comparatively high maximum adsorption capacity (360.5 mg g^?1). © 2015 Society of Chemical Industry     

Surface molecularly imprinted polymer prepared by reverse atom transfer radical polymerization for selective adsorption indole

The preparation of indole molecularly imprinted polymers (indole‐MIPs) using 4‐vinylpyridine as functional monomer, silica gel as matrix were used to adsorb indole from fuel oil specifically. The reverse atom transfer radical polymerization (RATRP) technology was introduced to prepare the surface molecularly imprinted polymers, and the precipitation polymerization was adopted in the preparation process. The obtained indole‐MIPs were characterized by nitrogen adsorption, Fourier transform infrared spectrometry and scanning electron microscopy. The results show that indole‐MIPs were provided with the larger surface areas and more pores. The adsorption capacity of indole‐MIPs was 31.80 mg g^?1 at 298 K, and the adsorption equilibrium was reached in a short time. The adsorption process was spontaneous by thermodynamic analysis, and an appropriate decrease in temperature could enhance the adsorption capacity. The adsorption process obeyed pseudo‐second‐order kinetic model by kinetics analysis. The isotherm analysis results show that both Langmuir and Sips equations were suitable to experimental data. The selective adsorption and reusable performance of indole‐MIPs were favorable. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40473.     

Synthesis and characterization of a surface imprinting silica gel polymer functionalized with phosphonic acid groups for selective adsorption of Fe(III) from aqueous solution

A Fe(III) ion‐imprinted silica gel polymer functionalized with phosphonic acid groups (IIP‐PA/SiO₂) was prepared with surface imprinting technique by using Fe(III) ion as template ion, grafted silica gel as support, and vinylphosphonic acid as functional monomer. The polymer was characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, transmission electron microscopy, Brunauer–Emmett–Teller, and thermogravimetric analysis. The synthesized imprinted silica gel polymer was used as a sorbent for Fe(III) adsorption. The adsorption properties, such as the effect of solution pH, adsorption kinetic, adsorption isotherm, adsorption selectivity as well as the regeneration of sorbent were studied. The results showd that the prepared sorbent (IIP‐PA/SiO₂) had a short adsorption equilibrium time (12 min) and high adsorption capacity (29.92 mg g^?1) for Fe(III) at the optimal pH of 2.0. The selectivity coefficients of the sorbent for Fe(III) in presence of Cr(III), M_n (II), and Zn(II) were 51.76, 27.86, and 207. 76, respectively. Moreover, the adsorption capacity of the prepared sorbent did not decrease significantly after six repeated use. Thus, the prepared ion‐imprinted silica gel polymer was a promising candidate sorbent for the selective adsorption of Fe(III) from aqueous solutions. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45165.     

Surface modification of rubber (Hevea brasiliensis) leaves for the adsorption of copper ions: kinetic,thermodynamic and binding mechanisms

BACKGROUND: This research describes the adsorption of copper ions from aqueous solutions following the modification of rubber (Hevea brasiliensis) leaves with formaldehyde solution. The main objectives of this research were to identify the binding mechanisms of copper ions on the chemically modified rubber leaves by spectroscopic techniques and to investigate the effects of several important physicochemical parameters such as pH, copper concentration, contact time, adsorbent dose and temperature on copper removal. RESULTS: Based on a kinetic study, the pseudo‐second‐order model was found to fit the experimental results well, while the Boyd kinetic model indicated that the rate‐determining step was due to film diffusion. Adsorption isotherms were modelled by the Langmuir and Freundlich isotherm equations, with the former providing a better fit for the data. Based on the Langmuir model, the maximum adsorption capacities of Cu(II) ions at 300, 310 and 320 K were 8.36, 8.61 and 8.71 mg g^?1, respectively. Thermodynamic parameters such as the Gibbs free energy (ΔG°), enthalpy (ΔH°) and entropy changes (ΔS°) were calculated. The adsorption process was spontaneous as the values of ΔG° were negative, and endothermic as higher adsorption capacities were recorded at higher temperatures. More than 80% of copper ions bound on the adsorbent were able to be desorbed using 0.02 mol L^?1 HCl, HNO₃ and EDTA solutions. Besides ion exchange, surface complexation could also play a major role in copper binding. CONCLUSION: Due to its relative abundance and satisfactory adsorption capacity, the modified rubber leaves can be considered as a good low‐cost adsorbent for removing copper ions from dilute aqueous solutions. Copyright © 2008 Society of Chemical Industry     

Polymer‐grafted banana (Musa paradisiaca) stalk as an adsorbent for the removal of lead(II) and cadmium(II) ions from aqueous solutions: kinetic and equilibrium studies

This study examined the effectiveness of a new adsorbent prepared from banana (Musa paradisiaca) stalk, one of the abundantly available lignocellulosic agrowastes, in removing Pb(II) and Cd(II) ions from aqueous solutions. The adsorbent (PGBS‐COOH) having a carboxylate functional group at its chain end was synthesized by graft copolymerization of acrylamide on to banana stalk, followed by functionalization. Batch adsorption experiments were carried out as a function of solution pH, ionic strength, contact time, metal concentration, adsorbent dose and temperature. A pH range of 5.5–8.0 was found to be effective for the maximum removal for both Pb(II) and Cd(II). Metal uptake was found to decrease with increase in ionic strength due to the expansion of the diffuse double layer and, more importantly, the formation of some chloro complexes (since NaCl was used in the adjustment of ionic strength), which do not appear to be adsorbed to the same extent as cations [M²⁺ and M(OH)⁺]. The kinetic studies showed that an equilibrium time of 3 h was needed for the adsorption of Pb(II) and Cd(II) on PGBS‐COOH and adsorption processes followed a pseudo‐second‐order equation. The Langmuir isotherm model fitted the experimental equilibrium data well. The maximum sorption capacity for Pb(II) and Cd(II) ions was 185.34 and 65.88 mg g^?1, respectively, at 30 °C. The thermodynamic parameters such as changes in free energy (ΔG°), enthalpy (ΔH°) and entropy (ΔS°) were derived to predict the nature of adsorption. The isosteric heat of adsorption was found to be independent of surface coverage. Adsorption experiments were also conducted using a commercial cation exchanger, Ceralite IRC‐50, for comparison. Synthetic wastewater samples were treated with the adsorbent to demonstrate its efficiency in removing Pb(II) and Cd(II) ions from industrial wastewaters. Acid regeneration was tried for several cycles with a view to recovering the sorbed metal ions and also restoring the sorbent to its original state. Copyright © 2005 Society of Chemical Industry     

Removal of Orange II by Phosphonium-modified Algerian Bentonites

An Algerian montmorillonite was modified with two organic surfactants, methyltriphenyl phosphonium bromide and n-hexyltriphenyl phosphonium bromide. The solids obtained were used as adsorbents to remove Orange II, an anionic dye from aqueous solutions. Batch experiments were conducted to study the effects of temperature (20–60°C), initial concentration of adsorbate (50–150 mg L^?1) and pH of solution 6.5 on dye adsorption. Due to their organophilic nature, exchanged montmorillonites were able to adsorb Orange II at a very high level. Adsorption of Orange II for B-NHTPB and B-MTPB at different pH show that the adsorption capacity clearly decreases with an increase in pH of the initial solution from 2 to 8, this decrease being dramatic for pH > 8. This may be due to hydrophobic interactions of the organic dye with both phosphonium molecules and the remaining non-covered portion of siloxane surface. The kinetics of the adsorption was discussed on the basis of three kinetic models, i.e., the pseudo-first-order, the pseudo-second-order, and the intraparticle diffusion models. Equilibrium is reached after 30 min and 60 min for B-MTPB and B-NHTPB, respectively; the pseudo-second-order kinetic model described very well the adsorption of Orange II on modified bentonites. The non-linear Langmuir model provided the best correlation of experimental data, maximum adsorption of Orange II is 53.78 mg g^?1 for B-NHTPB and 33.79 mg g^?1 for B-MTPB. The thermodynamic parameters, such as free energy of adsorption (ΔG°), enthalpy change (ΔH°), and entropy change (ΔS°) were also determined and evaluated. From thermodynamic studies, it was deduced that the adsorption was spontaneous and exothermic.     

Silica gel‐based adsorbents prepared via homogeneous and heterogeneous routes: adsorption properties and recycling as heterogeneous catalysts

Silica gel‐based adsorbents were prepared via homogeneous and heterogeneous routes using two silane coupling reagents, 3‐glycidoxypropyltrimethoxysilane and γ ‐chloropropyltrimethoxysilane. Characterization results showed that amino contents of the adsorbents prepared via the homogeneous route were higher than those of the adsorbents prepared via the heterogeneous route for both silane coupling reagents. The adsorption capabilities of the resulting four types of adsorbents for Hg(II), Cu(II), Au(III), Ni(II), Pb(II) and Ag(I) ions were compared. Good adsorption capability for Au(III) was observed for the new adsorbents and the maximum static saturated adsorption capacities for Au(III) could reach 0.67 mmol g^?1. Due to the formation of Au(0) particles in the adsorption process, which hampered the reusability of the spent adsorbents, alternative recycling of the spent adsorbents after Au(III) adsorption was sought. The spent adsorbents were treated with NaBH₄ and used as catalysts in the reduction of 4‐nitrophenol to 4‐aminophenol. After three catalytic cycles at 298 K, the k values indicated minimal decrease of catalytic activity. © 2017 Society of Chemical Industry     

Recycling of reactive dye using semi‐interpenetrating polymer network from sodium alginate and isopropyl acrylamide

A sequence of semi‐interpenetrating polymer network (semi‐IPN) were synthesized by free radical photo copolymerizing acrylic acid and isopropyl acrylamide (NIPAAm) in aqueous sodium alginate (NaAlg). Their structures (FT‐IR), thermal stability (TG/DTG), morphology (SEM), mechanical properties, reactive blue 4 (RB 4) dye adsorption (624 mg/g) and its dying characteristics, reusability of dye and adsorbent were evaluated. TG thermograms of semi‐IPN in air revealed zero order kinetics for initial step thermal degradation with an activation energy of 68.68 kJ/mol. Dye adsorption showed best fit for Langmuir adsorption isotherm and the kinetics followed pseudo‐second‐order model. The water and dye diffusion kinetics followed non‐Fickian mechanism. The changes in thermodynamic parameters namely Gibbs free energy (ΔG°), entropy (ΔS°) and enthalpy (ΔH°) indicated that the adsorption was spontaneous and exothermic process for RB 4/semi‐IPN system. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40968.     

Influence of synthesis conditions on the production of molecularly imprinted polymers for the selective recovery of isovaleric acid from anaerobic effluents

Two molecularly imprinted polymers (MIPs) – poly(methacrylic acid‐co‐TRIM) (TRIM, trimethylolpropanetrimethacrylate) and poly(acylamide‐co‐TRIM) – were synthesized in different solvents for the selective recovery of isovaleric acid (template) generated during the anaerobic digestion process. The chemical and structural characterizations of the synthetic adsorbent were carried out by Fourier transform infrared spectroscopy, TGA and porosimetry through N₂ adsorption–desorption isotherms. The selective and adsorptive performances of the imprinted polymers were evaluated by kinetic, isothermal, thermodynamic and selectivity studies and by adsorbent reuse experiments. The poly(methacrylic acid‐co‐TRIM) synthesized with dimethyl sulfoxide:chloroform presented higher selectivity and adsorption capacity for isovaleric acid in the presence of six volatile fatty acids. The kinetic results were well adjusted to the pseudo‐nth order and intraparticle diffusion models, leading to k values of 10^?4 and 6 × 10^?5 for the best synthesis of MIPs and not‐imprinted polymers, respectively. Moreover, the Sips model best described the adsorption isotherm and generated a maximum adsorption capacity of ca 209 mg g^?1 (at 25 °C). Cycles of MIP use–desorption–reuse indicated that the selective adsorbent performed better than commercial adsorbents, losing less than 3% of adsorption capacity after three cycles. © 2018 Society of Chemical Industry     

Optimization and analysis of nickel adsorption on microwave irradiated rice husk using response surface methodology (RSM)

BACKGROUND: The removal of heavy metals using adsorption techniques with low cost biosorbents is being extensively investigated. The improved adsorption is essentially due to the pores present in the adsorbent. One way of improving the porosity of the material is by irradiation of the precursor using microwaves. In the present study, the adsorption characteristics of nickel onto microwave‐irradiated rice husks were studied and the process variables were optimized through response surface methodology (RSM). RESULT: The adsorption of nickel onto microwave‐irradiated rice husk (MIRH) was found to be better than that of the raw rice husk (RRH). The kinetics of the adsorption of Ni(II) from aqueous solution onto MIRH was found to follow a pseudo‐second‐order model. Thermodynamic parameters such as standard Gibbs free energy (ΔG°), standard enthalpy (ΔH°), and standard entropy (ΔS°) were also evaluated. The thermodynamics of Ni(II) adsorption onto MIRH indicates that it is spontaneous and endothermic in nature. The response surface methodology (RSM) was employed to optimize the design parameters for the present process. CONCLUSION: Microwave‐irradiated rice husk was found to be a suitable adsorbent for the removal of nickel(II) ions from aqueous solutions. The adsorption capacity of the rice husk was found to be 1.17 mg g^?1. The optimized parameters for the current process were found as follows: adsorbent loading 2.8 g (100 mL)^?1; Initial adsorbate concentration 6 mg L^?1; adsorption time 210 min.; and adsorption temperature 35 °C. Copyright © 2008 Society of Chemical Industry     

Development of PU‐TZnO solid‐phase extractor for selective detection of mercury in complex matrices

In this study, a new effective solid‐phase extractor (PU‐TZnO 3) was developed for a selective extraction and determination of mercury using inductively coupled plasma optical emission spectrometry. The selectivity of PUA (PU‐TZnO 0.5, PU‐TZnO 1, PU‐TZnO 3, or PU‐TZnO 5) was investigated toward several metal ions, including Au(III), Cd(II), Co(II), Cu(II), Hg(II), Pb(II), Pd(II), and Zn(II). Based on selectivity and pH studies, Hg(II) was the most quantitatively adsorbed on PU‐TZNO 3 phase at pH 2, indicating that PU‐TZnO 3 is more selective for Hg(II) as compared to other metal ions. Based on the adsorption isotherm analysis, the maximum adsorption capacity of PU‐TZnO 3 phase for Hg(II) was found to be 99.68 mg g⁻¹, following the Langmuir adsorption isotherm model. Further kinetic models suggested pseudo second‐order kinetic model for adsorption of Hg(II) on the PU‐TZnO 3. In addition, results of thermodynamic investigation demonstrated that a general spontaneous process is favorable for adsorption mechanism of Hg(II) on PU‐TZnO 3. POLYM. COMPOS., 38:2106–2112, 2017. © 2015 Society of Plastics Engineers     

Adsorption kinetics and isotherms of a pesticide on polyester fibers by carrier finishing

The effective management and control of mosquitoes in human living environments are crucial to minimize vector‐borne diseases in homes. Pesticides, such as pyrethroids, are considered powerful tools in the control of mosquitoes and are intended to be incorporated into textiles. The adsorptive behavior of the pesticide ZX‐1 [the main component is 1,1,1‐trichloro‐2,2‐bis(p‐chlorophenyl) ethane] in aqueous solution on polyesters fibers at different treatment times, temperatures, and concentrations are discussed in this article. The second‐order model was found to be the most suitable for describing the kinetic diffusion process, and the intraparticle diffusion was the rate‐controlling process. The Langmuir, Freundlich, and Dubinin–Radushkevich adsorption models were applied to these approaches. The results show that the Langmuir model appeared to fit the adsorption of ZX‐1 on the polyester fibers better than other adsorption models. In addition, thermodynamic parameters, such as the free energy of adsorption (ΔG⁰), enthalpy (ΔH⁰), and entropy, were calculated. Positive values of ΔH⁰ and ΔG⁰ indicated the endothermic and nonspontaneous nature of ZX‐1 adsorption on the polyester fibers. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation of grafted polytetrafluoroethylene fibers and adsorption of bilirubin

BACKGROUND: A successful hemoperfusion technique requires that the adsorbent for bilirubin should have a high specificity, adsorption capacity and adsorption rate, blood compatibility and no toxicity. Compared with polymer microbeads, polytetrafluoroethylene (PTFE) fibers have many advantages. The aim of the work reported here was to prepare a new polytetrafluoroethylene‐graft‐poly(glycidyl methacrylate)‐block‐polyethyleneimine (PTFE‐g‐PGMA‐b‐PEI) adsorbent for bilirubin based on PTFE fibers by the ⁶⁰Co radiation‐induced graft polymerization of GMA followed by the chemical modification of the epoxy groups on the PTFE‐g‐PGMA fibers with PEI. In addition, the adsorption properties of this novel adsorbent for bilirubin were examined. RESULTS: The highest content of amino groups obtained on the PTFE‐g‐PGMA‐b‐PEI fibers was 1.87 mmol g^?1. The maximum adsorption capacity of the grafted fibers was 9.6 mg g^?1 at pH = 6.5. Bilirubin adsorption on these fibers obeyed the Langmuir model. Also, these fibers possessed the ability to selectively adsorb bilirubin in the presence of bovine serum albumin. CONCLUSION: The PTFE‐g‐PGMA‐b‐PEI fibers have a high adsorption capacity for bilirubin and excellent adsorption properties. In addition, this new adsorbent is inexpensive, easy to prepare and has no toxicity. So the PTFE‐g‐PGMA‐b‐PEI fibers as a biomedical adsorbent are promising for the removal of bilirubin through the hemoperfusion technique. Copyright © 2009 Society of Chemical Industry     

Synthesis and characterization of polystyrene‐supported glucosamine resin and its adsorption behavior for Au(III)

A novel chelating resin, crosslinking polystyrene‐supported glucosamine (PS‐GA), was prepared and its structure was confirmed by FTIR, elemental analysis, and X‐ray photoelectron spectroscopy. The adsorption properties of PS‐GA for Au(III) were investigated. PS‐GA resin possessed excellent enriching property to Au(III) ions and adsorption proportion E% could reach to about 90 shortly after 3 h. The adsorption dynamics of Au(III) showed that the adsorption was controlled by liquid film diffusion and the apparent activation energy E_a was 12.91 kJ mol^?1. Both Langmuir model and Freundlich model could describe the isothermal process of Au(III), and ΔG, ΔH, ΔS values were calculated. The mechanism of adsorption for Au(III) was confirmed by FTIR, SEM, and XPS. The results showed that redox reaction occurred and both coordination and ion‐exchange existed simultaneously in the adsorption. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4581–4586, 2006     

Syntheses and characterization of polystyrene‐supported 2,5‐dimercapto‐1,3,4‐thiodiazole and its sorption behavior for Pd(II), Pt(IV), and Au(III)

A type of chelating resin crosslinking polystyrene‐supported 2,5‐dimercapto‐1,3,4‐thiodiazole (also called bismuththiol I, BMT), containing sulfur and nitrogen atoms, was prepared. The structure of PS‐BMT was confirmed by FTIR, elemental analysis, and X‐ray photoelectron spectroscopy (XPS). Adsorption of Pd(II), Pt(IV), and Au(III) was investigated. The capacity of PS‐BMT to adsorb Pd(II) and Pt(IV) was 0.190 and 0.033 mmol/g, respectively. The adsorption dynamics of Pd(II) showed that adsorption was controlled by liquid film diffusion and that the apparent activation energy, E_a, was 32.67 kJ/mol. The Langmuir model was better than the Freundlich model in describing the isothermal process of Pd(II), and the ΔG, ΔH, and ΔS values calculated were ?0.33 kJ/mol, 26.29 kJ/mol, and 87.95 J mol^?1 K^?1, respectively. The mechanisms of adsorption of Pd(II), Pt(IV), and Au(III) were confirmed by XPS. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 631–637, 2006     

Selective separation and concentration of Pd(II) from Fe(III), Co(II), Ni(II), and Cu(II) ions using thiourea‐formaldehyde resin

Thiourea‐formaldehyde (TUF), a well‐known chelating resin, has been synthesized and it was used in the adsorption, selective separation, and concentration of Pd(II) ions from Fe(III), Co(II) Ni(II), and Cu(II) base metal ions. The composition of the synthesized resin was determined by elemental analysis. The effect of initial acidity/pH and the adsorption capacity for Pd(II) ions were studied by batch technique. The adsorption and separation of Pd(II) were then examined by column technique. FTIR spectra and SEM/EDS analysis were also recorded before and after the adsorption of Pd(II). The optimum pH was found to be 4 for the adsorption. The adsorption data fitted well to the Langmuir isotherm. The maximum adsorption capacity of the TUF resin for Pd(II) ions was found to be 31.85 mg g⁻¹ (0.300 mmol g⁻¹). Chelating mechanism was effective in the adsorption. Pd(II) ions could be separated efficiently from Fe(III), Cu(II), Ni(II), and Co(II) ions using TUF resin. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011