Polymer electrolyte membranes prepared by EB‐crosslinking of sulfonated poly(ether ether ketone) with 1,4‐butanediol

Crosslinked sulfonated poly(ether ether ketone) (SPEEK) membranes were prepared through the electron beam (EB)‐irradiation crosslinking of SPEEK/1,4‐butanediol under various irradiation conditions and used as a proton exchange membrane (PEM) for fuel cell applications. The crosslinked membranes were characterized by gel fraction, a universal testing machine (UTM), dynamic mechanical analysis (DMA), and small‐angle X‐ray scattering (SAXS). The gel fraction of the crosslinked membranes was used to estimate the degree of crosslinking, and the gel fraction was found to be increased with an increase of the crosslinker content and EB‐absorbed dose. The UTM results indicate that a brittle EB‐crosslinked membrane becomes more flexible with an increase in the crosslinker content. The DMA results show that the EB‐crosslinked membranes have well‐developed ionic aggregation regions and the cluster T_g of membranes decrease with an increase in the 1,4‐butanediol crosslinker content. The SAXS results show that the Bragg and persistence distance of crosslinked membranes increase with an increase in the crosslinker content. The proton conductivities of the EB‐crosslinked membranes were more than 9 × 10^?2 S/cm. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41760.     

Imidazole/(HPO3)3‐doped sulfonated poly (ether ether ketone) composite membrane for fuel cells

A novel gel of imidazole/(HPO₃)₃ was synthesized and incorporated into sulfonated poly (ether ether ketone) (SPEEK) to fabricate composite proton exchange membranes. The composite membranes were characterized by alternating current impedance (AC), thermogravimetry (TG), differential scanning calorimetry (DSC), X‐ray diffraction (XRD), scanning electron microscope (SEM) and mechanical property test. Based on the electrochemical performance investigation, the proton conductivity of the membrane is intimately correlated with the temperature and the mass ratio of imidazole/(HPO₃)₃ in the composite. The SPEEK/imidazole/(HPO₃)₃?4 composite membrane (with 44.4 wt % of imidazole/(HPO₃)₃) has the optimized performance at 135°C. Mover, the strength of the composite membranes is almost comparable to that of Nafion membrane. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41946.     

Effect of phosphotungstic acid blending on properties of sulfonated poly(ether ether ketone)–poly(ethylene glycol) crosslinked membranes

This study shows the effect of phosphotungstic acid (PWA) blended into a sulfonated poly(ether ether ketone) (SPEEK) and poly(ethylene glycol) (PEG) crosslinked membrane on the membrane's electrochemical and mechanical properties. The PWA weight percentage was varied from 0 to 50%. All of the membranes were equilibrated with water at room temperature (27 °C) and elevated temperature (60 °C), and their properties were investigated. A scanning electron microscope with energy dispersive X‐ray was used to ascertain the tungsten concentration remaining in the membrane after water treatment. A systematic decrease in tungsten concentration was seen with the increase in the initial PWA percentage. The membrane blended with 10% PWA showed the best properties, having the highest conductivity (0.11 S cm^?1), mechanical strength, and chemical stability. Membranes with 10% PWA and without PWA were studied in a H₂/O₂ fuel cell. The membrane blended with 10% PWA gave 33% more power density than the membrane without PWA. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46667.     

Montmorillonite‐reinforced sulfonated poly(phthalazinone ether sulfone ketone) nanocomposite proton exchange membranes for direct methanol fuel cells

To produce a composite membrane with high conductivity and low permeability, SPPESK with a degree of sulfonation of 101% was carefully selected for the preparation of montmorillonite (MMT)‐reinforced SPPESK using solution intercalation. The fundamental characteristics such as water uptake, swelling ratio, proton conductivity, methanol permeability, and mechanical properties of the composite membranes were studied. Water uptake is improved when organic MMT (OMMT) loading increase. The composite membranes with CTAB‐MMT loading of 4–0.5% show 0.143–0.150 S cm^?1 proton conductivity at 80°C, which approaches the value of Nafion112. In addition, methanol permeability was decreased to 6.29 × 10^?8 cm² s^?1 by the addition of 6 wt % OMMT. As a result, the SPPESK‐MMT composite membrane is a good candidate for use in direct methanol fuel cells. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39852.     

Sulfonated graphene oxide‐doped proton conductive membranes based on polymer blends of highly sulfonated poly(ether ether ketone) and sulfonated polybenzimidazole

Simultaneously improving the proton conductivity and mechanical properties of a polymer electrolyte membrane is a considerable challenge in commercializing proton exchange membrane fuel cells. In response, we prepared a new series of miscible polymer blends and thus the corresponding crosslinked membranes based on highly sulfonated poly(ether ether ketone) and sulfonated polybenzimidazole. The blended membranes showed more compact structures, due to the acid‐base interactions between the two constituents, and improved mechanical and morphological properties. Further efforts by doping sulfonated graphene oxide (s‐GO) forming composite membranes led to not only significantly elevated proton conductivity and electrochemical performance, but also better mechanical properties. Notably, the composite membrane with the filler content of 15 wt % exhibited a proton conductivity of 0.217 S cm^?1 at 80 °C, and its maximum power density tested by the H₂/air single PEMFC cell at room temperature reached 171 mW cm^?2, almost two and half folds compared with that of the native membrane. As a result, these polymeric membranes provided new options as proton exchange membranes for fuel‐cell applications. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46547.     

Synthesis and characterization of a new type of sulfonated poly(ether ether ketone ketone)s for proton exchange membranes

A novel series of sulfonated poly(ether ether ketone ketone)s (SPEEKKs) were prepared by aromatic nucleophilic polycondensation with different ratios of 1,3‐bis(3‐sodium sulfonate‐4‐fluorobenzoyl)benzene to 1,3‐bis(4‐fluorobenzoyl)benzene. ¹H‐NMR spectroscopy was used to confirm the degrees of sulfonation (DS) of the polymers. Thermal stabilities of the SPEEKKs in acid form were characterized by thermogravimetric analysis (TGA), which showed that SPEEKKs were excellently thermally stable at high temperatures. SPEEKK polymers can be easily cast into tough membranes. Both of proton conductivity and methanol diffusion coefficient have been tested in this article. Other properties of the SPEEKK membranes were investigated in detail. The results show that the SPEEKK membranes are promising in proton exchange membrane fuel cells (PEMFCs) application. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Highly selective sulfonated poly(vinylidene fluoride‐co‐hexafluoropropylene)/poly(ether sulfone) blend proton exchange membranes for direct methanol fuel cells

Proton exchange membranes (PEMs) based on blends of poly(ether sulfone) (PES) and sulfonated poly(vinylidene fluoride‐co‐hexafluoropropylene) (sPVdF‐co‐HFP) were prepared successfully. Fabricated blend membranes showed favorable PEM characteristics such as reduced methanol permeability, high selectivity, and improved mechanical integrity. Additionally, these membranes afford comparable proton conductivity, good oxidative stability, moderate ion exchange capacity, and reasonable water uptake. To appraise PEM performance, blend membranes were characterized using techniques such as Fourier transform infrared spectroscopy, AC impedance spectroscopy; atomic force microscopy, and thermogravimetry. Addition of hydrophobic PES confines the swelling of the PEM and increases the ultimate tensile strength of the membrane. Proton conductivities of the blend membranes are about 10^?3 S cm^?1. Methanol permeability of 1.22 × 10^?7cm² s^?1 exhibited by the sPVdF‐co‐HFP/PES10 blend membrane is much lower than that of Nafion‐117. AFM studies divulged that the sPVdF‐co‐HFP/PES blend membranes have nodule like structure, which confirms the presence of hydrophilic domain. The observed results demonstrated that the sPVdF‐co‐HFP/PES blend membranes have promise for possible usage as a PEM in direct methanol fuel cells. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43907.     

Effect of thermal crosslinking on the properties of sulfonated poly(phenylene sulfone)s as proton conductive membranes

The synthesis and characterization of crosslinked aromatic polymer membranes with high ion exchange capacity (IEC) values are reported. Through aromatic nucleophilic substitution polycondensation and the subsequent sulfonation reaction, the highly sulfonated polymers SPPSU‐2S and SPPSU‐4S with high molecular weight (M_n = 138–145 kDa, M_w = 200–279 kDa) and well‐defined structures were synthesized. By solution casting and thermal annealing treatment, flexible crosslinked membranes with high solvent insolubility were obtained. The membranes exhibited mechanical and chemical stability as confirmed by dynamic mechanical analysis (DMA) and conductivity measurement. The crosslinked SPPSU‐4S membrane with IEC = 3.20 meq/g showed the highest proton conductivity of 0.163 S/cm at 120 °C, 90% RH, and improved thermal stability compared with its precursor (uncrosslinked) membrane. The results show that simple annealing method could improve significantly membranes properties of highly sulfonated aromatic polymers. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44218.     

Proton exchange membrane based on crosslinked sulfonated polyphosphazene containing pendent perfluorosulfonic acid groups with sulfonated poly(ether ether ketone)

A series of crosslinked membranes based on new sulfonated polyphosphazene bearing pendent perfluorosulfonic acid groups (PMFP‐g‐PS) and sulfonated poly (ether ether ketone) were prepared and evaluated as proton exchange membranes for direct methanol fuel cells (DMFCs). The structure of PMFP‐g‐PS was characterized by Fourier transform infrared spectroscopy, ¹H and ¹⁹F NMR spectra. In comparison with the pristine PMFP‐g‐PS membrane, the crosslinked membranes showed improved water uptakes and proton conductivities. The methanol permeability values of the membranes were in the range of 1.32 × 10^?7 to 3.85 × 10^?7 cm²/s, which were lower than Nafion 117 (12.1 × 10^?7 cm²/s). The selectivity of all the membranes was much higher compared with Nafion 117. Furthermore, transmission electron microscopy observation revealed that clear phase‐separated structures were well dispersed and connected to each other in the membranes. These membranes displayed high water uptakes and low swelling ratios, high proton conductivities, low methanol permeability values, good thermal, and oxidative stabilities. The results indicate that these membranes are potential candidate proton exchange membrane materials for DMFCs. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43492.     

A new sulfonated poly(ether sulfone) hybrid with low humidity dependence for high‐temperature proton exchange membrane fuel cell applications

A new sulfonated poly(ether sulfone) (PES) hybrid with low humidity dependence was prepared based on a new synthesized PES and Udel as a commercial PES. The PES was synthesized based on a pyridine containing diol which is able to change between pyridine and pyridinium salt forms during the cell performance (acidic condition) and facilitate proton transfer. The presence of nitrogen group increases inter and intramolecular interactions in the membrane and enhance proton hopping mechanism. Thermogravimetrical analysis of PES hybrid shows good thermal stability. Proton conductivity measurements were evaluated on a fuel cell test station, showing that the membrane has better performance under lower humidity (relative humidity = 60%) compare to the fully hydrated condition (relative humidity = 100%). The results reveal that proton transfer might be mainly accomplished through proton hopping mechanism at higher temperatures. The membrane also shows significant proton conductivity at 120 °C (about 6.6 mS cm^?1 at RH = 30%). © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45342.     

Novel imidazole‐grafted hybrid anion exchange membranes based on poly(2,6‐dimethyl‐1,4‐phenylene oxide) for fuel cell applications

Novel organic–inorganic hybrid membranes, based on poly(2,6‐dimethyl‐1,4‐phenylene oxide), have been prepared through 1,2‐dimethylimidazole functional groups and double crosslinking agents including 3‐glycidyloxypropyltrimethoxysilane and tetraethyl orthosilicate by sol–gel process for the purpose of improving the conductivity and alkaline resistance. The structure of membranes was characterized using Fourier‐transform infrared spectra, ¹H NMR, and X‐ray diffraction. The physico‐chemical properties of all membranes were shown in ion exchange capacity, water uptake, stability, and conductivity. Membranes with OH^– conductivity up to 0.022 at 25 °C and 0.036 S cm^?1 at 80 °C. Promisingly, the chemical stability of the resulting membranes remains unchanged after storage in 2 mol dm^?3 KOH at 25 °C over at least 10 days. The tensile strength can be higher than 30 MPa, and the elongation at break (Eb) is in the range 6.68–10.84%. Hence, this hybrid membrane can be potentially applied in alkaline fuel cells. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46034.     

Synthesis and properties of sulfonated poly(phosphazene)‐graft‐poly(styrene‐co‐N‐benzylmaleimide) copolymers via atom transfer radical polymerization for proton exchange membrane

A series of sulfonated poly(phosphazene)‐graft‐poly(styrene‐co‐N‐benzylmaleimide) (PP‐g‐PSN) copolymers were prepared via atom transfer radical polymerization (ATRP), followed by regioselective sulfonation which occurred preferentially at the poly(styrene‐co‐N‐benzylmaleimide) sites. The structures of these copolymers were confirmed by Fourier transform infrared (FTIR) spectroscopy, ¹H‐NMR, and ³¹P‐NMR, respectively. The resulting sulfonated PP‐g‐PSN membranes showed high water uptakes (WUs), low water swelling ratios (SWs), low methanol permeability coefficients, and proper proton conductivities. In comparison with non‐grafting sulfonated poly(bis(phenoxy)phosphazene) (SPBPP) membrane previously reported, the present membranes displayed higher proton conductivity, significantly improved the thermal and oxidative stabilities. Transmission electron microscopy (TEM) observation showed clear phase‐separated structures resulting from the difference in polarity between the hydrophobic polyphosphazene backbone and hydrophilic sulfonated poly(styrene‐co‐N‐benzylmaleimide) side chains, indicating effective ionic pathway in these membranes. The results showed that these materials were promising candidate materials for proton exchange membrane (PEM) in direct methanol fuel cell (DMFC) applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42251.     

Preparation of novel semihomogeneous cation‐permeable membranes from blends of sulfonated poly(phenylene sulfide) and sulfonated phenolphthalein poly(ether ether ketone)

A series of semihomogeneous cation‐exchange membranes were prepared with binary blend systems, such as sulfonated phenolphthalein poly(ether ether ketone) (SPEEK‐C)/sulfonated poly(phenylene sulfide) (SPPS), or ternary blend systems, such as phenolphthalein poly(ether ether ketone) (PEEK‐C)/SPEEK‐C/SPPS, by solution blending and phase inversion, in which PEEK‐C and SPEEK‐C acted as binders and SPPS powder acted as a polyelectrolyte. Compared with homogeneous and heterogeneous membranes, the prepared semihomogeneous membranes had good electrochemical properties and mechanical strength as well as good dimensional stability. The fundamental properties of the membranes, such as the ion‐exchange capacity, water content, electrical resistance, transport number, diffusion coefficient of the electrolytes, and streaming potential, were largely dependent on both the loading of the SPPS resin and the sulfonation degree of PEEK‐C. Through the adjustment of these two important parameters, a series of semihomogeneous membranes with the desired conductivity and selectivity and the proper water content for different industrial purposes, such as electrodialysis, diffusional dialysis, and proton exchange, were achieved. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1478–1485, 2004     

Partial crosslinking method for poly(2,6‐dimethyl‐1,4‐phenylene oxide)–poly(vinyl alcohol) membranes to obtain optimized stability and permeability

A partial crosslinking method was developed to modify hydrophilic membranes. The membrane was sandwiched between two porous plates to protect part of the areas, then immersed into a crosslinking solution such as glutaraldehyde, and finally, set free from the plates. The protected and unprotected areas were alternatively distributed to form a heterogeneous membrane. The unprotected areas were crosslinked to enhance the membrane stability, whereas the protected areas retained their original permeability. Three types of hydrophilic base membranes were selected and prepared from poly(2,6‐dimethyl‐1,4‐phenylene oxide) and poly(vinyl alcohol). The base membranes were partially crosslinked (5.56% of the direct area with enlarged areas) to investigate their stability and diffusion dialysis (DD) performances. The partially crosslinked membranes had remarkably reduced water uptake and swelling degrees compared with the base membranes (72.4–250.4 vs 178.2%–544.4% and 94.0%–408.0% vs. 163.8%–814.8%). Meanwhile, the membranes still retained high DD performances for separating HCl–FeCl₂ or NaOH–NaAlO₂ solutions. The dialysis coefficients of HCl and NaOH were much higher than those of the fully crosslinked membranes (0.0209 vs. 0.0109 m/h and 0.0059–0.0085 vs. 0.0017–0.0022 m/h). Hence, partial crosslinking was effective in optimizing the membrane hydrophilicity and permeability. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45305.     

A methanesulfonic acid/sulfuric acid‐based route for easily‐controllable chloromethylation of poly(ether ether ketone)

A mixed methanesulfonic acid/sulfuric acid solvent based chlromethylation of poly(ether ether ketone) (PEEK) is described. Methanesulfonic acid is the solvent, sulfuric acid is the catalyst, and chloromethyl octyl ether (CMOE) is the chloromethylating reagent. ¹H‐NMR spectra confirmed the successful synthesis of chloromethylated PEEK (CMPEEK). The effects of polymer concentration, catalyst/polymer ratio, and reaction temperature on the rate of PEEK chloromethylation were investigated. In order to minimize crosslinking, the PEEK concentration must be kept very low (< 2%). The reaction rate increases with increased catalyst/polymer ratio and reaction temperature. The activation energy of PEEK chloromethylation is 30.9 kJ mol^?1. The extent of reaction for the new route is more easily controllable as compared with the previous sulfuric acid based route. The reaction rate constant at 25°C for the new route is 1.29 h^?1 which is lower than that for chloromethylation by concentrated sulfuric acid at ?10°C (rate constant 1.88 h^?1). As a result, the degree of chloromethylation of CMPEEK can be easily controlled at room temperature using this mixed solvent. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41404.     

Behavior of sulfonated poly(ether ether ketone) in ethanol–water systems

The behavior of sulfonated poly(ether ether ketone) (sPEEK) membranes in ethanol–water systems was studied for possible application in direct ethanol fuel cells (DEFCs). Polymer membranes with different degrees of sulfonation were tested by means of uptake, swelling, and ethanol transport with dynamic measurements (liquid–liquid and liquid–gas systems). Ethanol permeability was determined in an liquid–liquid diffusion cell. For membranes with an ion‐exchange capacity (IEC) between 1.15 and 1.75 mmol/g, the ethanol permeability varied between 5 × 10^?8 and 1 × 10^?6 cm²/s, being dependent on the measuring temperature. Ethanol and water transport in liquid–gas systems was tested with pervaporation as a function of IEC and temperature. Higher IEC accounted for higher fluxes and lower water/ethanol selectivity. The temperature had a large effect on the fluxes, but the selectivity remained constant. Furthermore, the membranes were characterized with proton conductivity measurements. The proton diffusion coefficient was calculated, and a transition in the proton transfer mechanism was found at a water number of 12. Membranes with high IEC (>1.6 mmol/g) exhibited larger proton diffusion coefficients in ethanol–water systems than in water systems. The membrane with the lowest IEC exhibited the best proton transport to ethanol permeability selectivity. The use of sPEEK membranes in DEFC systems depends on possible modifications to stabilize the membranes in the higher conductive region rather than on modifications to increase the proton conductivity in the stable region. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synergistic effect of aluminium phosphate and tungstophosphoric acid on the physicochemical properties of sulfonated poly ether ether ketone nanocomposite membrane

This study explores the synergistic effect of aluminium phosphate (ALP) nanoparticles and tungstophosphoric acid (TPA) on the physicochemical properties of sulfonated poly ether ether ketone (SPEEK) nanocomposite membranes. SPEEK/TPA/ALP nanocomposite containing optimum TPA (10 wt %) and varying ALP content (3–10 wt %) are fabricated to investigate the effect of ALP nanoparticles on membrane properties. Experimental results reveal that nanocomposite membrane containing 3 wt % ALP nanoparticles and 10 wt % TPA exhibits 3.3 and 18.8 times higher proton conductivity compared to 10 wt % TPA filled SPEEK composite membrane and reference SPEEK membrane. ALP nanoparticles help in retaining water within the membranes and thus 59.4% reduction in water desorption rate is achieved compared to SPEEK/TPA membrane. The leaching of TPA is reduced by 34.5% which helps in retaining membrane properties. Membranes are thermally stable up to 200°C. Microstructure of the composite films is investigated by scanning electron microscope. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42952.     

Branched poly(biphenylene-co-sulfone)ether ion exchange membranes containing perfluorocyclobutane groups for fuel cell applications

A series of branched poly(biphenylene-co-sulfone) ion exchange membranes containing perfluorocyclobutane groups were prepared for fuel cells. Two bifunctional trifluorovinyloxy-terminated monomers (sulfonable 4,4′-bis(trifluorovinyloxy)biphenyl and insulfonable 4,4′-sulfonyl-bis(trifluorovinyloxy)biphenyl) and a trifunctional trifluorovinyloxy-terminated branching agent (1,1,1-tris(4′-trifluorovinyloxyphenyl)ethane) were synthesized and terpolymerized via thermal [2π + 2π] cyclodimerization to obtain partially fluorinated and branched polymers containing 0–5 mol% of the branching agent. They were then postsulfonated by chlorosulfonic acid at room temperature, cast as membranes, and characterized to evaluate their electrochemical properties for fuel cell applications. As the branching agent content was increased, their polydispersity values highly increased, indicating they became highly branched. It was confirmed that higher branching agent content also increased the ion exchange capacity, water uptake, and proton conductivity of the branched ion exchange membranes containing perfluorocyclobutane groups. This indicates that their electrochemical properties can be easily controlled by the degree of branching. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48373.     

Hydrophilic TiO2 decorated carbon nanotubes/sulfonated poly(ether ether ketone) composite proton exchange membranes for fuel cells

Sulfonated poly(ether ether ketone) (SPEEK) is currently considered to be one of the most potential candidates of commercial perfluorinated sulfonic acid proton exchange membranes. To balance the proton conductivity and mechanical properties of SPEEK, nano TiO₂ coated carbon nanotubes (TiO₂@CNTs) were prepared using a benzyl alcohol-assisted sol-gel method and then used as a new nanofiller to modify SPEEK to prepare SPEEK/TiO₂@CNTs composite membranes. The thick insulated TiO₂ coating layer can effectively avoid the risk of electronic short-circuiting formed by CNTs, while the hydrophilicity of TiO₂ can also reduce the polar difference between CNTs and SPEEK matrix, thus promoting the homogeneous dispersion of CNTs in the composites. As a result, the composite membranes demonstrated simultaneously improved strength and proton conductivity. Incorporating 5 wt% of TiO₂@CNTs exhibited 31% growth in mechanical strength when compared with pure SPEEK. Moreover, the maximum conductivity was 0.104 S cm⁻¹ (80°C) for the composite membrane with 5 wt% of TiO₂@CNTs, which was nearly twice as high as that of SPEEK membrane (0.052 S cm⁻¹).     

Novel polymer electrolyte membranes based on semi‐interpenetrating blends of poly(vinyl alcohol) and sulfonated poly(ether ether ketone)

In this work, the properties of novel ionic polymer blends of crosslinked and sulfonated poly(vinyl alcohol) (PVA) and sulfonated poly(ether ether ketone) (SPEEK) are investigated. Crosslinking and sulfonation of PVA were carried out using sulfosuccinic acid (SSA) in the presence of dispersed SPEEK to obtain semi‐interpenetrating network blends. PVA–SSA/SPEEK blend membranes of different compositions were studied for their ion‐exchange capacity, proton conductivity, water uptake, and thermal and mechanical properties. The hydrated blend membranes show good proton conductivities in the range of 10^?3 to 10^?2 S/cm. When compared with pure component membranes, the PVA–SSA/SPEEK blend membranes also exhibit improvement in tensile strength, tensile modulus, and delay in the onset of thermal and chemical degradation. Semi‐interpenetrating nature of the blends is established from morphology and dynamic mechanical analysis. Morphology of the membranes was studied using scanning electron microscopy after selective chemical treatment. The dynamic mechanical properties of the membranes are examined to understand the miscibility characteristics of the blends. The relative proportions of PVA and SPEEK and the degree of crosslinking of PVA–SSA are important factors in determining the optimum properties for the blend. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013