Synthesis and absorbency of a superabsorbent from sodium starch sulfate‐g‐polyacrylonitrile

A sodium starch sulfate–based superabsorbent was synthesized to improve water and saline absorbencies. A sodium starch sulfate with high degree of substitution was synthesized by the reaction of starch gelatinized with dimethyl acetamide (DMAc)/lithium chloride (LiCl) and a dimethyl formamide–sulfur trioxide (DMF–SO₃) complex. The sodium starch sulfate was then graft‐polymerized with acrylonitrile and the nitrile groups of the sodium starch sulfate‐g‐polyacrylonitrile were converted to a mixture of hydrophilic carboxamide and carboxylate groups by alkaline hydrolysis. The hydrolyzed sodium starch sulfate‐g‐polyacrylonitrile copolymer exhibited improved water and saline absorbencies compared with that of existing starch‐based superabsorbents, resulting from the presence of sulfate groups. The maximum water and saline absorbencies of the sodium starch sulfate–based superabsorbent were 1510 and 126.4 g/g, respectively. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1423–1430, 2001     

Stereocomplex formation between poly(L‐lactic acid) and poly(D‐lactic acid) with disproportionately low and high molecular weights from the melt

Poly(L ‐lactic acid) (PLLA) and poly(D ‐lactic acid) (PDLA) with very different weight‐average molecular weights (M_w) of 4.0 × 10³ and 7.0 × 10⁵ g mol^?1 (M_w(PDLA)/M_w(PLLA) = 175) were blended at different PDLA weight ratios (X_D = PDLA weight/blend weight) and their crystallization from the melt was investigated. The presence of low molecular weight PLLA facilitated the stereocomplexation and thereby lowered the cold crystallization temperature (T_cc) for non‐isothermal crystallization during heating and elevated the radial growth rate of spherulites (G) for isothermal crystallization, irrespective of X_D. The orientation of lamellae in the spherulites was higher for the neat PLLA, PDLA and an equimolar blend than for the non‐equimolar blends. It was found that the orientation of lamellae in the blends was maintained by the stereocomplex (SC) crystallites. Although the G values are expected to decrease with an increase in X_D or the content of high‐molecular‐weight PDLA with lower chain mobility compared with that of low‐molecular‐weight PLLA, G was highest at X_D = 0.5 where the maximum amount of SC crystallites was formed and the G values were very similar for X_D = 0.4 and X_D = 0.6 with the same enantiomeric excess. This means that the effect of SC crystallites overwhelmed that of chain mobility. The nucleating mechanisms of SC crystallites were identical for X_D = 0.1–0.5 in the T_c range 130–180 °C. Copyright © 2011 Society of Chemical Industry     

EDTA and pH‐sensitive crosslinking polymerization of acrylic acid, 2‐acrylamidoglycolic acid,and 2‐acrylamide‐2‐methyl‐1‐propanesulfonic acid

Network formation was monitored by shear storage modulus (G′) during free radical crosslinking polymerization to investigate the effects of pH and ethylenediaminetetraacetic acid (EDTA; a complex agent). Three types of acrylic monomers, acrylic acid (AAc), 2‐acrylamidoglycolic acid (AmGc), and 2‐acrylamido‐2‐methyl propanesulfonic acid (AmPS), were polymerized in the presence of a crosslinking agent. The ratio of crosslinking agent (methylene bis‐acrylamide; MBAAm) to monomer was varied as: 0.583 × 10^?3, 1.169 × 10^?3, 1.753 × 10^?3, and 2.338 × 10^?3. G′ of the hydrogel in crosslinking polymerizations of AAc and AmPS was effectively increased by addition of EDTA, which was not the case for the crosslinking polymerization of AmGc. The order of magnitude of G′ differed based on the acidity of monomer. The maximum values of G′ in crosslinking polymerizations of AAc, AmGc, and AmPS were ～20,000 Pa, 6000 Pa, and 400 Pa, respectively. G′ varied linearly with the molecular weight between crosslinks (M_wc). pH and EDTA‐complex affected the rate of intramolecular propagation during crosslinking polymerization. Our results indicated that G′ was primarily affected by the following factors in the order: (1) acidity of monomer, (2) M_wc, and (3) physical interactions induced by pH and EDTA. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41026.     

Cassava starch‐graft‐polymethacrylamide copolymers as flocculants and textile sizing agents

Cassava starch‐graft‐polymethacrylamide (PMAM) copolymers were synthesized by a free‐radical‐initiated polymerization reaction, and the products were tested for their efficiency as flocculants and textile sizing agents. The highest percentages of grafting and monomer conversion were 79.9 and 78.0%, respectively. The grafted starches were characterized by Fourier transform infrared spectroscopy, X‐ray diffraction analysis, scanning electron microscopy, differential scanning calorimetry, and thermogravimetric analysis. The average molecular weight of PMAM chains in the grafted starches ranged from 15.9 to 30.8 × 10⁵ g/mol. The grafted starches exhibited a higher peak viscosity and paste stability in comparison to the native starch (NS). Dynamic mechanical analysis showed that grafting provided fairly shear‐stable hydrogels, and the highest storage modulus obtained was 17,900 Pa compared to 1879 Pa for NS. The flocculation studies demonstrated the superiority of starch‐g‐PMAM over cassava starch and PMAM as an efficient flocculant. The tensile strength of cotton yarns sized with the starch‐grafted copolymer was significantly higher (104 MPa) compared to that sized with NS (34 MPa). © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39810.     

Synthesis and biological activity of medium range molecular weight polymers containing exo‐3,6‐epoxy‐1,2,3,6‐tetrahydrophthalimidocaproic acid

A new monomer, exo‐3,6‐epoxy‐1,2,3,6‐tetrahydrophthalimidocaproic acid (ETCA), was prepared by reaction of maleimidocaproic acid and furan. The homopolymer of ETCA and its copolymers with acrylic acid (AA) or with vinyl acetate (VAc) were obtained by photopolymerizations using 2,2‐dimethoxy‐2‐phenylacetophenone as an initiator at 25 °C. The synthesized ETCA and its polymers were identified by FTIR, ¹H NMR and ¹³C NMR spectroscopies. The apparent average molecular weights and polydispersity indices determined by gel permeation chromatography (GPC) were as follows: M_n = 9600 g mol^?1, M_w = 9800 g mol^?1, M_w/M_n = 1.1 for poly(ETCA); M_n = 14 300 g mol^?1, M_w = 16 200 g mol^?1, M_w/M_n = 1.2 for poly(ETCA‐co‐AA); M_n = 17 900 g mol^?1, M_w = 18 300 g mol^?1, M_w/M_n = 1.1 for poly(ETCA‐co‐VAc). The in vitro cytotoxicity of the synthesized compounds against mouse mammary carcinoma and human histiocytic lymphoma cancer cell lines decreased in the following order: 5‐fluorouracil (5‐FU) ≥ ETCA > polymers. The in vivo antitumour activity of the polymers against Balb/C mice bearing sarcoma 180 tumour cells was greater than that of 5‐FU at all doses tested. © 2001 Society of Chemical Industry     

Degradation and biodegradation of polyethylene with pro‐oxidant aditives under compost conditions establishing relationships between physicochemical and rheological parameters

In the present work, an analysis is carried out to provide a relationship between the Molecular Weight (M_w) of degraded LDPE films (containing Mn stearate as pro oxidant (MnSt‐LDPE) and changes in viscosity, elongation at break (EB %) and carbonyl index (CI) occurring during thermal degradation in the thermophilic phase of the compost process. The thermal treatment comprised various temperatures (50°C, 60°C, and 70°C) and exposure times, and was characterized through a so‐called Energy‐Time Factor (the product of thermal energy and exposure time). Changes in viscosity, EB %, and CI were correlated to this factor. A modified Mark‐Houwink equation was used to relate the zero shear‐rate viscosity and M_w of the degraded LDPE films. Results indicate that the EB %, M_w and viscosity decrease simultaneously with an increase in the CI as the Energy‐Time Factor augments, allowing the assessment of the variation of these properties with M_w. Calculations of the percentage abiotic degradation (%D) of LDPE films indicate that a M_w of 6 kg mol^?1 corresponds to a maximum abiotic degradation degree of 91.85%, which is henceforth susceptible to biodegradation. The film treated with Energy‐Time Factor of 2.79E+09 J s mol^?1 reached a 74% of biodegradation in 90 days (average time of the composting process). Results exhibit clearly the correlation between abiotic and biotic degradation. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42721.     

Preparation of high‐molecular‐weight poly(L‐lactic acid)‐based polymers through direct condensation polymerization in bulk state

Poly(L ‐lactic acid‐co‐succinic acid‐co‐1,4‐butanediol) (PLASB) was synthesized by a direct condensation copolymerization of L ‐lactic acid, succinic acid (SA), and 1,4‐butanediol (BD) in bulk state using titanium(IV) butoxide (TNBT) as a catalyst. Weight average molecular weight (M_w) of PLASB increased from 3.5 × 10⁴ to 2.1 × 10⁵ as the content of SA and BD went up from 0.01 to 0.5 mol/100 mol of L ‐lactic acid (LA). PLASB having M_w in the range from 1.8 × 10⁵ to 2.1 × 10⁵ showed tensile properties comparable to those of commercially available poly(L ‐lactic acid) (PLLA). In sharp contrast, homopolymerization of LA in bulk state produced PLLA with M_w as low as 4.1 × 10⁴, and it was too brittle to prepare specimens for the tensile tests. M_w of PLASB synthesized by using titanium(IV)‐2‐ethyl(hexoxide), indium acetate, indium hydroxide, antimony acetate, antimony trioxide, dibutyl tin oxide, and stannous‐2‐ethyl 1‐hexanoate was compared with that of PLASB obtained by TNBT. Ethylene glycol oligomers with different chain length were added to LA/SA in place of BD to investigate effect of chain length of ethylene glycol oligomers on the M_w of the resulting copolymers. Biodegradability of PLASB was analyzed by using the modified Sturm test. Toxicity of PLASB was evaluated by counting viable cell number of mouse fibroblast cells that had been in contact with PLASB discs. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 466–472, 2006     

Hydrogels from dextran and soybean oil by UV photo‐polymerization

In this work, hydrogels were synthesized by UV photo‐polymerization of hydrophilic dextran functionalized with acrylate groups (Dex‐A) and hydrophobic acrylate epoxidized soybean oil (AESO). The acrylation of dextran was accomplished by reacting dextran (M_w 70,000 g mol^?1) with acryloyl chloride and pyridine. The Dex‐A was characterized by Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance (NMR). Five rigid hydrogels were prepared using the weight ratios of Dex‐A and AESO as 10/90, 20/80, 30/70, 40/60, and 50/50. The hydrogels were characterized by FTIR, thermal gravimetric analyses (TGA) and scanning electronic microscopy (SEM). The experimental results demonstrated that the swelling and release profiles of the Dex‐A/AESO hydrogels can be tailored by varying the ratio of Dex‐A and AESO thus varying the balance of hydrophilicity and hydrophobicity of the network structures and the crosslinking density. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41446.     

The swelling behaviors and network parameters of cationic starch‐g‐acrylic acid/poly(dimethyldiallylammonium chloride) semi‐interpenetrating polymer networks hydrogels

Amphiphilic semi‐interpenetrating polymer networks (semi‐IPN) hydrogels were prepared by a sequential‐IPN method by acrylic acid graft copolymerization into cationic starch in mild aqueous media of poly(dimethyldiallylammonium chloride). Some main factors were investigated to evaluate the swelling of hydrogels, and the network parameters M_c were given accordingly to elaborate the interaction between polymers. The chemical structure of the resulting hydrogel was confirmed using Fourier transform infrared spectroscopy. The cationic starch‐based semi‐IPN hydrogels achieved a high swelling capacity of 1070 g/g in deionized water and 94 g/g in 0.9 wt % NaCl solution, respectively) and high compressive stress in a high water content. Besides, a different pH‐dependent behavior was found for this semi‐IPN hydrogel. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Trimethylsilyl‐substituted triazole‐based ligand for copper‐mediated single‐electron transfer living radical polymerization of methyl methacrylate

The tripodal ‘click’ compound tris(4‐trimethylsilylmethyl‐1,2,3‐triazolylmethyl)amine (TTTA) was prepared and investigated as a ligand for copper‐catalysed single‐electron transfer living radical polymerization of methyl methacrylate (MMA). Bulk polymerizations catalysed by Cu⁰/CuBr₂/TTTA with a molar ratio of [MMA]₀/[ethyl‐2‐bromoisobutyrate]₀/[CuBr₂]₀/[TTTA]₀ = 200:2:1:1 and a 1.0 × 1.0 cm² Cu⁰ sheet were fast and well controlled (76% conversion with M_w/M_n = 1.19 after 3.5 h). Greater amounts of added air generally gave slower polymerizations although M_w/M_n remained low (<1.3) even when the polymerization was carried out under aerobic conditions. Decreasing initial concentrations of the Cu⁰/CuBr₂/TTTA catalyst system or polymerization temperatures also resulted in slower polymerizations and yielded polymers with broader dispersity. Kinetic studies in the temperature range 40–90 °C revealed an apparent activation energy of 22.6 kJ mol^?1. © 2014 Society of Chemical Industry     

Effect of reaction conditions on grafting ratio and properties of starch nanocrystals‐g‐polystyrene

Starch nanocrystals‐g‐polystyrene (StN‐g‐PS) was synthesized by free radical emulsion copolymerization of starch nanocrystals with styrene. The effect of polymerization conditions on grafting efficiency (GE) and grafting ratio (GR) were investigated. It was found that during graft copolymerization procedure both GE and GR increase with increasing monomer concentration and reaction time. As a result the high GE and high GR can be achieved. The good linear fit of the GR with A_St/A_OH (the absorption strength ratio of aromatic ring peaks and hydroxyl group peaks) confirmed that during graft copolymerization, FTIR spectra can be used as a simple method for determining GR. X‐ray diffraction showed that the crystallinity of StN‐g‐PS decreased slightly with increasing GR. Grafted polystyrene side chains can improve the interface compatibility of starch nanocrystals with the hydrophobic polymer matrix. The mechanical properties of StN‐g‐PS/rubber nanocomposites can be obviously enhanced. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40571.     

Microbiocidal activity of chitosan‐N‐2‐hydroxypropyl trimethyl ammonium chloride

Chitosan‐N‐2‐hydroxypropyl trimethyl ammonium chloride (QTS) was prepared by reaction of chitosan with glycidyl trimethylammonium chloride, which was characterized by FTIR. QTS with different molecular weights (M_w 41.55 × 10⁴, 9.02 × 10⁴, 3.57 × 10⁴, and 0.17 × 10⁴) showed biocidal activity on Staphylococcua aureus, Bacillus subtilis, Staphylococcua epidermidis, and Candida albicans. QTS with high molecular weight had high biocidal activity on the gram‐positive bacteria, and the biocidal effect of QTS decreased with decreasing molecular weight from 9.02 × 10⁴ to 0.17 × 10⁴. QTS with M_w 41.55 × 10⁴ exhibits slightly lower biocidal activity on Candida albicans than other QTS samples. However, no remarkable biocidal activity of QTS was found on gram‐negative bacteria Escherichia coli and Pseudomonas aeruginosa at the concentration up to 10 g L^?1. Existence of cationic surfactant, amphoteric surfactant, nonionic surfactant, Ca²⁺ and Mg²⁺ had no remarkable effect on microbiocidal activity of these QTS samples. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3851–3856, 2007     

Free radical scavenging activity of cellulase‐treated chitosan

Partially N‐acetylated chitosan was hydrolyzed by the cheap, commercially available, and efficient cellulase. The products, with different molecular weight, were comparatively investigated by GPC, FT‐IR, XRD, and NMR. The results show that the decrease of molecular weight led to transformation of crystal structure and increase of water‐solubility, but the chemical structures of residues were not modified. Superoxide anion radical and hydroxyl radical quenching assay were used for the evaluation of free radical scavenging activity of cellulase‐treated chitosan in vitro. Low molecular weight chitosan (LMWC3, M_w 1.7 × 10³) exhibited high scavenging activity against free radical. It scavenged 79.3% superoxide radical at 0.1 mg mL^?1. At 2.0 mg mL^?1, scavenging percentage of initial chitiosan, LMWC1 (M_w 27.3 × 10³), LMWC2 (M_w 5.9 × 10³), and LMWC3 (M_w 1.7 × 10³) against hydroxyl radical was 14.3%, 33.1%, 47.4%, and 65.9%, respectively. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

DNA adsorption on poly(N,N‐dimethylacrylamide)‐grafted chitosan hydrogels

In this study, poly(N,N‐dimethylacrylamide) grafted chitosan (PDMAAm‐g‐CT) hydrogels were prepared for deoxyribonucleic acid (DNA) adsorption. Instead of directly grafting the N,N‐dimethylacrylamide (DMAAm) monomer onto the chitosan (CT) chains, poly(N,N‐dimethylacrylamide) with carboxylic acid end group (PDMAAm‐COOH) was firstly synthesized by free‐radical polymerization using mercaptoacetic acid (MAAc) as the chain‐transfer agent and then grafted onto the CT having amino groups. The synthesis of PDMAAm‐COOH and its grafting onto the CT chains were confirmed by attenuated total reflectance Fourier transform infrared (ATR‐FTIR) spectroscopy. From gel permeation chromatography measurements, the number‐average molecular weight (M _n) and polydispersity index of PDMAAm‐COOH were found as 2400 g/mol and 2.3, respectively. The PDMAAm‐g‐CT hydrogels were utilized as the adsorbents in DNA adsorption experiments conducted at +4°C in a trisEDTA solution of pH 7.4. The hydrogels produced with higher PDMAAm‐COOH content exhibited higher DNA adsorption capacity. The DNA adsorption capacity up to 4620 μg DNA/g dry gel could be achieved with the PDMAAm‐g‐CT hydrogels prepared in 80.0 wt % PDMAAm‐COOH feed concentration. This value is approximately seven times higher than that of CT alone. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis of star‐shaped poly(ϵ‐caprolactone) by samarium‐based tetrafunctional initiator and its dilute‐solution properties

An in situ–generated tetrafunctional samarium enolate from the reduction of 1,1,1,1‐tetra(2‐bromoisobutyryloxymethyl)methane with divalent samarium complexes [Sm(PPh₂)₂ and SmI₂] in tetrahydrofuran has proven to initiate the ring‐opening polymerization of ?‐caprolactone (CL) giving star‐shaped aliphatic polyesters. The polymerization proceeded with quantitative conversions at room temperature in 2 h and exhibited good controllability of the molecular weight of polymer. The resulting four‐armed poly(?‐caprolactone) (PCL) was fractionated, and the dilute‐solution properties of the fractions were studied in tetrahydrofuran and toluene at 30°C. The Mark–Houwink relations for these solvents were [η] = 2.73 × 10^?2M_w^0.74 and [η] = 1.97 × 10^?2M_w^0.75, respectively. In addition, the unperturbed dimensions of the star‐shaped PCL systems were also evaluated, and a significant solvent effect was observed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 175–182, 2006     

Synthesis and biological activity of phthalimide‐based polymers containing 5‐fluorouracil

The attachment of anticancer agents to polymers is a promising approach towards reducing the toxic side‐effects and retaining the potent antitumour activity of these agents. A new tetrahydrophthalimido monomer containing 5‐fluorouracil (ETPFU) and its homopolymer and copolymers with acrylic acid (AA) and with vinyl acetate (VAc) have been synthesized and spectroscopically characterized. The ETPFU contents in poly(ETPFU‐co‐AA) and poly(ETPFU‐co‐VAc) obtained by elemental analysis were 21 mol% and 20 mol%, respectively. The average molecular weights of the polymers determined by gel permeation chromatography were as follows: M_n = 8900 g mol^?1, M_w = 13 300 g mol^?1, M_w/M_n = 1.5 for poly(ETPFU); M_n = 13 500 g mol^?1, M_w = 16 600 g mol^?1, M_w/M_n = 1.2 for poly(ETPFU‐co‐AA); M_n = 8300 g mol^?1, M_w = 11 600 g mol^?1, M_w/M_n = 1.4 poly(ETPFU‐co‐VAc). The in vitro cytotoxicity of the compounds against FM3A and U937 cancer cell lines increased in the following order: ETPFU > 5‐FU > poly(ETPFU) > poly(ETPFU‐co‐AA) > poly(ETPFU‐co‐VAc). The in vivo antitumour activities of all the polymers in Balb/C mice bearing the sarcoma 180 tumour cell line were greater than those of 5‐FU and monomer at the highest dose (800 mg kg^?1). © 2002 Society of Chemical Industry     

Europium‐containing cholesteric liquid crystalline polymers in the side chain

Europium‐containing cholesteric liquid crystalline polymers were graft copolymerized using poly(methylhydrogeno)siloxane, cholesteryl 4‐(allyloxy)benzoate (M₁), cholesteryl acrylate (M₂), and a europium complexes monomer (M₃). The chemical structures of the monomers were characterized by Fourier transform infrared and ¹H‐nuclear magnetic resonance. The mesomorphic properties and phase behavior were investigated by differential scanning calorimetry, thermo gravimetric analysis, polarizing optical microscopy, and X‐ray diffraction. With an increase of europium complexes units in the polymers, the glass transition temperature (T_g) did not change significantly; the isotropic temperature (T_i) and mesophase temperature range (ΔT) decreased. All polymers showed typical cholesteric Grandjean textures, which was confirmed by X‐ray diffraction. The temperatures at which 5% weight loss occurred (T_d) were greater than 300°C for the polymers. The introduction of europium complexes units did not change the liquid crystalline state of polymer systems; on the contrary, the polymers were enabled with the significant luminescent properties. With Eu³⁺ ion contents ranging between 0 and 1.5 mol %, luminescent intensity of polymers gradually increased and luminescent lifetimes were longer than 0.45 ms for the polymers. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40866.     

Dynamic light‐scattering characterization of the molecular weight distribution of unfractionated polyimide

Using a developed laser light‐scattering (LLS) procedure, we accomplished the characterization of an unfractionated polyimide (UPI) in CHCl₃ at 25°C. The Laplace inversion of precisely measured intensity–intensity time correlation function from dynamic LLS leads us first to an estimate of the characteristic line‐width distribution G(Γ), and then to the translational diffusion coefficient distribution G(D). By using a previously established calibration of D (cm²/s) = 3.53 × 10^?4 M^?0.579, we were able to convert G(D) into a molecular weight distribution. The weight‐average molecular weight M_w, calculated from the molecular weight distribution, agrees well with that directly measured in static LLS. Our results indicate that both the calibration and LLS procedure used in this study are ready to be applied as a routine method for the characterization of the molecular weight distribution of polyimide. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1670–1674, 2001     

Swelling characteristics and in vitro drug release study with pH‐ and thermally sensitive hydrogels based on modified chitosan

The grafting of a poly(ethylene glycol) diacrylate macromer onto a chitosan backbone was carried out with different macromer concentrations. The grafting was achieved by (NH₄)₂Ce(NO₃)₆‐induced free‐radical poly merization. Biodegradable, pH‐ and thermally responsive hydrogels of poly(ethylene glycol)‐g‐chitosan crosslinked with a lower amount of glutaraldehyde were prepared for controlled drug release studies. Both the graft copolymers and the hydrogels were characterized with Fourier transform infrared, elemental analysis, and scanning electron microscopy. The obtained hydrogels were subjected to equilibrium swelling studies at different temperatures (25, 37, and 45°C) in buffer solutions of pHs 2.1 and 7.4 (similar to those of gastric and intestinal fluids, respectively). 5‐Fluorouracil was entrapped in these hydrogels, and equilibrium swelling studies were carried out for the drug‐entrapped gels at pHs 2.1 and 7.4 and 37°C. The in vitro release profile of the drug was established at 37°C and pHs 2.1 and 7.4. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 977–985, 2006     

Synthesis and chain extension of poly(L‐lactic acid‐co‐succinic acid‐co‐1,4‐butene diol)

L ‐Lactic acid (LA) was copolymerized with succinic acid (SA) and 1,4‐butenediol (1,4‐BED) in bulk state with titanium(IV) butoxide as a catalyst to produce poly(LA‐co‐SA‐co‐1,4‐BED) (PLASBED). Poly(L ‐lactic acid) (PLLA) homopolymer obtained from a direct condensation polymerization of LA had weight average molecular weight (M_w) less than 4.1 × 10⁴ and was too brittle to prepare specimens for the tensile test. Addition of SA and 1,4‐BED to LA produced PLASB with M_w as high as 1.4 × 10⁵ and exhibited tensile properties comparable to a commercially available high‐molecular‐weight PLLA. Chain extension by intermolecular linking reaction through the unsaturated 1,4‐BED units in PLASBED with benzoyl peroxide further increased the molecular weight and made PLASBED more ductile and flexible to show elongation at break as high as 450%. Biodegradability of PLASBED measured by the modified Sturm test was nearly independent of the 1,4‐BED content. Gel formation during the chain extension did not exert any significant influence on the biodegradability either. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1116–1121, 2005