Preparation and characterization of high‐performance poly(ether ether ketone) fibers with improved spinnability based on thermotropic liquid crystalline poly(aryl ether ketone) copolymer

High‐performance poly(ether ether ketone) (PEEK) fibers were prepared by melt‐spinning in the presence of thermotropic liquid crystalline poly(aryl ether ketone) copolymer (FPAEKLCP). The rheological and mechanical properties, birefringence, orientation, and crystallization of the resulting PEEK/FPAEKLCP fibers were characterized by using a melt flow indexer, capillary rheometer, single fiber electronic tensile strength tester, polarized light microscopy (PLM), and wide‐angle X‐ray diffraction (WAXD), respectively. The results indicate that the melt viscosity of PEEK significantly reduced by introducing FPAEKLCP, followed by the improvements in the spinnability and the quality of as‐spun fibers. The tensile properties of PEEK/FPAEKLCP fibers mainly depend on the content of FPAEKLCP, drawing temperature, drawing ratio, and annealing processes. Moreover, the tensile strength and modulus of PEEK/FPAEKLCP fibers are obviously higher than those of neat PEEK fibers under the same processing conditions. This should be attributed to an enhancement in the orientation and crystallization of PEEK compounded with FPAEKLCP. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1406‐1414, 2013     

Properties and crystallization kinetics of poly(ether ether ketone)‐co‐poly(ether ether ketone ketone) block copolymers

A series of block copolymers composed of poly(ether ether ketone) (PEEK) and poly(ether ether ketone ketone) (PEEKK) components were prepared from their corresponding oligomers via a nucleophlilic aromatic substitution reaction. Various properties of the copolymers were investigated with differential scanning calorimetry (DSC) and a tensile testing machine. The results show that the copolymers exhibited no phase separation and that the relationship between the glass‐transition temperature (T_g) and the compositions of the copolymers approximately followed the formula T_g = T_g1X₁ + T_g2X₂, where T_g1 and T_g2 are the glass‐transition‐temperature values of PEEK and PEEKK, respectively, and X₁ and X₂ are the corresponding molar fractions of the PEEK and PEEKK segments in the copolymers, respectively. These copolymers showed good tensile properties. The crystallization kinetics of the copolymers were studied. The Avrami equation was used to describe the isothermal crystallization process. The nonisothermal crystallization was described by modified Avrami analysis by Jeziorny and by a combination of the Avrami and Ozawa equations. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1652–1658, 2005     

Influence of the addition of lubricant on the properties of poly(ether ether ketone) fibers

A high‐temperature lubricant genioplast pellets (GPPS) was used in order to improve the processing behavior of poly(ether ether ketone) (PEEK) resin and high‐performance PEEK fibers were produced by melt‐spinning. The rheological properties of spinning material, morphology, mechanical, and thermal properties of PEEK fibers were characterized by using a polymer capillary rheometer, scanning electron microscopy, single fiber electronic tensile strength tester, wide‐angle X‐ray diffraction and thermal gravimetric analyzer, respectively. The results indicated that the introduction of lubricant GPPS decreased the melting viscosity of PEEK resin and improved spinnability of PEEK resin without sacrificing its thermal properties. The filaments are cylindrical with smooth surface and uniform diameter. The optimized content of GPPS was determined to be 1.0 wt% by balancing the decreased torque and changes of the mechanical properties. The strength and modulus of PEEK fibers were 420 MPa and 3.6 GPa, respectively. This should be due to the improvement in spinnability, followed by the enhancements in the orientation and crystallization of PEEK fibers in the process of drawing and annealing. POLYM. ENG. SCI., 53:2254–2260, 2013. © 2013 Society of Plastics Engineers     

Effect of thermotropic liquid crystalline poly(ether ketone)arylates on the processibility and properties of poly(ether ether ketone)s fibers

A series of composite fibers based on poly(ether ether ketone)s (PEEK) and a thermotropic liquid crystalline poly(ether ketone)arylates (PEKAR) have been prepared by melt spinning. The structure, compatibility, and properties of these composite fibers were investigated in detail by rheological measurements, differential scanning calorimetry, thermogravimetric analysis, wide‐angle X‐ray diffraction, scanning electron microscopy, orientation degree test, and mechanical properties test. The results showed that the addition of PEKAR could reduce the apparent melt viscosity of the blends obviously, which is beneficial in improving the processibility of PEEK at a relatively low temperature. After adding 1 wt % PEKAR to PEEK, the tensile strength of the post‐treatment fiber improved by 8.8%, whereas the crystallinity of the as‐spun fiber increased from 21.76% to 31.51%, and the orientation degree also increased with the addition of PEKAR. The result of morphology research suggested that PEKAR had a good compatibility with PEEK resin. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40595.     

Preparation and properties of poly(ether ether ketone) composites reinforced by modified wollastonite grafting with silaneterminated poly(ether ether ketone) oligomers

Silane-terminated poly(ether ether ketone) oligomers were synthesized and grafted onto wollastonite (W) particles. The prepared grafted-wollastonite particles (g-W) were then incorporated into PEEK matrix via melt processing. Properties of the PEEK composites were investigated using differential scanning calorimetry (DSC), universal tester and rheometer. The researchers found the mechanical properties of the PEEK/g-W composites were markedly enhanced, complex viscosity of the PEEK/g-W composites increased, and both the peak crystallization temperature (T _c ) and crystalline fraction (χ _c ) of the PEEK composites with g-W were significant higher compared with those of the PEEK composites with W. It is our belief that these results are due to the strong interaction between the grafted-wollastonite particles and the PEEK matrix.     

Isothermal crystallization behavior of nano-alumina particles-filled poly(ether ether ketone) composites

The isothermal crystallization behavior of nano-alumina particle-filled poly(ether ether ketone) (PEEK) composites has been investigated using differential scanning calorimeter. The results show that all the neat PEEK and nano-alumina-filled PEEK composites exhibit the double-melting behavior under isothermal crystallization. The peak crystallization times (τ_p) for all the neat PEEK and PEEK/aluminum oxide (Al₂O₃) composites increase with increasing crystallization temperature. Moreover, the crystallinity of the PEEK/Al₂O₃ composite with 7.5 wt % nano-filler content reached the maximum value of 44.8% at 290°C, higher than that of the neat PEEK polymer. From the lower value in τ_p and higher value in X_c for the PEEK/Al₂O₃ composites, the inclusion of the nano-alumina into the PEEK matrix favored the occurrence of heterogeneous nucleation. The Avrami exponents n of all the neat PEEK and PEEK/Al₂O₃ composites ranged from 2 to 3, and the n values for PEEK/Al₂O₃ composites were slightly higher than that of the neat PEEK polymer, indicating that the inclusion of the nano-filler made the crystallization mechanism more complex. However, the growth rate of crystallization was lowered as the nano- filler was introduced, and the decrease in growth rate reduced the grain size of the PEEK spherulites because of the lowering of molecule mobility during isothermal crystallization. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Study of tensile properties of multiwalled carbon nanotube/polyether ether ketone polymer composites at the nanoscale

This study demonstrates the microscale and nanoscale mechanical properties of a multiwalled carbon nanotubes/polyether ether ketone (MWCNTs/PEEK) composite utilizing a novel in situ testing method. Nanoscale testing specimens of a composite of PEEK thin film dispersed with 6.5 wt% MWCNTs were successfully prepared using focused ion beam (FIB) and investigated by a tensile testing device accommodated inside a field emission scanning electron microscope. The average tensile strength of the nanocomposite was measured to be 388.66 MPa. The average Young's modulus measured at 6.52 GPa demonstrated a 23% increase compared to that of the bulk specimen, suggesting a size‐dependent mechanism that limits the plastic deformation of the microscale specimens possibly due to the limited defects distribution and motion constraint of the polymer chain in the small specimen and the amorphous regions of the PEEK matrix. POLYM. ENG. SCI., 59:1209–1214 2019. © 2019 Society of Plastics Engineers     

Effect of the addition of silane coupling agents on the properties of wollastonite‐reinforced poly(ether ether ketone) composites

The wollastonite was grafted with different silane coupling agents, which could improve interface adhesion. Wollastonite and modified wollastonite‐reinforced poly(ether ether ketone) (PEEK) composites were prepared by melt blending. The mechanical properties, rheology behavior, and thermal properties of the composites were investigated. The modified wollastonite‐reinforced PEEK composites exhibited better mechanical properties than the unmodified wollastonite‐reinforced PEEK composites based on good interfacial adhesion. The composites had lower activation volume and complex shear viscosity. Furthermore, the modified wollastonite‐reinforced PEEK composites had higher crystallization peak temperature (T_c) and crystalline fraction (χ_c) compared with the unmodified wollastonite‐reinforced PEEK composites. This study shows that the traditional silane coupling agents could effectively improve the performance of PEEK composites. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Structural and mechanical characterization of poly(ether ether ketone) (PEEK) and sulfonated PEEK films: Effects of thermal history,sulfonation, and preparation conditions

In this work, virgin and sulfonated poly(ether ether ketone) films (PEEK and SPEEK, respectively) have been studied by dynamic mechanical analysis, modulated differential scanning calorimetry, wide‐angle X‐ray diffraction, birefringence, and optical microscopy. The properties of the unmodified polymer have been addressed to assess the original morphological characteristics and the changes induced by sulfonation. In general, the introduction of ionic groups in the polymer backbone alters dramatically the intrinsic properties of the parent material. The particular thermomechanical response exhibited by PEEK and SPEEK samples, characterized by a hysteresis loop, can be explained by the reversible and irreversible relaxation–orientation of the microstructure, even in the sub‐T_g region. The results showed that the preparation conditions largely determine the nonequilibrium morphological features of both compression‐molded PEEK films and solvent‐cast SPEEK membranes. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 756–774, 2006     

Preparation of honeycomb films from nitryl poly(ether ether ketone)s via water‐droplet templating

The fabrication of honeycomb‐patterned films from nitryl poly(ether ether ketone)s (PEEK‐NO₂) in a high‐humidity atmosphere was reported in this article. PEEK‐NO₂ was prepared through acid (nitric acid and sulfuric acid) nitration from poly(ether ether ketone)s (PEEK). The obtained polymer, which was characterized by Fourier transform infrared (FT‐IR), X‐ray diffraction (XRD), and differential scanning calorimetry (DSC) showed excellent solubility and thermal stability. Some influence factors on the pattern formation and the fabrication of the porous structure, such as the solution concentration, the solvent, and the atmosphere humidity, were investigated. The results showed that with the increase of the solution concentration, the aperture of the film diminished gradually; the lower the solvents´ boiling point were, the smaller the films´ apertures were and the more regular the pores´ arrange; only under high‐humidity circumstances could obvious and ordered honeycomb films be formed. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Hybrid fiber fabric composites from poly ether ether ketone and glass fiber

Poly ether ether ketone (PEEK) polymer was extruded into filaments and cowoven into unidirectional hybrid fabric with glass as reinforcement fiber. The hybrid fabrics were then converted into laminates and their properties with special reference to crystallization behavior has been studied. The composite laminates have been evaluated for mechanical properties, such as tensile strength, interlaminar shear strength (ILSS), and flexural strength. The thermal behavior of the composite laminates were analyzed using differential scanning calorimeter, thermogravimetric analyzer, dynamic mechanical analyzer (DMA), and thermomechanical analyzer (TMA). The exposure of the fabricated composite laminates to high temperature (400 and 500°C) using radiant heat source resulted in an improvement in the crystallanity. The morphological behavior and PEEK resin distribution in the composite laminates were confirmed using scanning electron microscope (SEM) and nondestructive testing (NDT). Although DMA results showed a loss in modulus above glass transition temperature (T_g), a fair retention in properties was noticed up to 300°C. The ability of the composite laminates to undergo positive thermal expansion as confirmed through TMA suggests the potential application of glass–PEEK composites in aerospace sector. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci 117:1446–1459, 2010     

Synthesis and properties of novel copolymers of poly(ether ketone diphenyl ketone ether ketone ketone) and poly(ether amide ether amide ether ketone ketone)

New monomers, 4,4′‐bis(4‐phenoxybenzoyl)diphenyl (BPOBDP) and N,N′‐bis(4‐phenoxybenzoyl)?4,4′‐diaminodiphenyl ether (BPBDAE), were conveniently synthesized via simple synthetic procedures from readily available materials. Novel copolymers of poly(ether ketone diphenyl ketone ether ketone ketone) (PEKDKEKK) and poly(ether amide ether amide ether ketone ketone) (PEAEAEKK) were synthesized by electrophilic Friedel‐Crafts solution copolycondensation of isophthaloyl chloride (IPC) with a mixture of BPOBDP and BPBDAE, over a wide range of BPOBDP/BPBDAE molar ratios, in the presence of anhydrous AlCl₃ and N‐methylpyrrolidone (NMP) in 1,2‐dichloroethane (DCE). The copolymers obtained were characterized by different physico‐chemical techniques. The copolymers with 10–40 mol% BPBDAE are semicrystalline and had remarkably increased T_gs over commercially available PEEK and PEKK due to the incorporation of amide and diphenyl linkages in the main chains. The copolymers IV and V with 30–40 mol% BPBDAE had not only high T_gs of 185–188°C, but also moderate T_ms of 326–330°C, having good potential for the melt processing. The copolymers IV and V had tensile strengths of 101.7–102.3 MPa, Young's moduli of 2.19–2.42 GPa, and elongations at break of 13.2–16.6% and exhibited high thermal stability and excellent resistance to organic solvents. POLYM. ENG. SCI., 54:1757–1764, 2014. © 2013 Society of Plastics Engineers     

The absorption behavior and crystallization of poly(aryl ether ketone) films

The absorption and subsequent desorption behaviors of amorphous polymer films of PEEK poly(ether ether ketone), PEEKK poly(ether ether ketone ketone), and PEKK poly(ether ketone ketone) in solvent of 1,2-dichloroethane (C₂H₄Cl₂) are investigated and compared. The equilibrium absorption weight (M_∞) of these polymers is related to their molecular ketone content or molecular chain rigidity and also to the experimental conditions. Especially, at a certain temperature, the molecular chains in the solvent can be polarized, which leads to producing greater M_∞ for polymer films; for example, at 60°C, M_∞ = 46% for PEEK and M_∞ = 65% for PEKK. The pseudodiffusion coefficients for PEEK, PEEKK, and PEKK all surpass the 6.0 × 10⁻¹² m² s⁻¹. The polymer's molecular polarization has been proved in concentrated sulfur acid. Results also show that amorphous resin's films become white and creeped in dichloroethane, which is more serious when metaphenyl links are introduced into PEEKK or PEKK molecular main chains. The residual solvent of 1% or so often exists in the films, even though a long desorption time (over 100 h) has been proceeded. Absorption has induced crystallization of amorphous polymer films, but this crystallization process is slightly different from that of the films crystallized from both the glassy state and the melting state in the solvent, which makes the amorphous interlayers grow progressively and more condensely; thus, the crystallized films will have higher T_g's than these crystallized under annealing condition. The morphology results have shown that the solvent-crystallized films are less toughened than the amorphous ones because of the intermediate layer between the induced crystallized area and the amorphous area in the core. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67:2065–2075, 1998     

Radiation-induced graft polymerization of functional monomer into poly(ether ether ketone) film and structure-property analysis of the grafted membrane

Radiation-induced graft polymerization of sulfo-containing styrene derivatives into crystalline poly(ether ether ketone) (PEEK) substrates was carried out to prepare thermally and mechanically stable polymer electrolyte membranes based on an aromatic hydrocarbon polymer, so-called “super-engineering plastics”. Graft polymerization of the sulfo-containing styrene, ethyl 4-styrenesulfonate (E4S) into a high crystalline PEEK substrate (degree of crystallinity: 32%) hardly progressed, whereas graft polymerization into a low crystalline PEEK substrate (degree of crystallinity: 11%) gradually progressed, achieving a grafting degree of more than 50% after 72 h. Oxygen radicals appeared in the ESR spectra of irradiated PEEK films, indicating that graft polymerization initiates from the phenoxy radicals generated by scission of PEEK main chains and proceeds so as to yield block type grafts. The PEEK-based polymer electrolyte membrane (PEM) converted by aqueous hydrolysis of grafted films exhibited mechanical strength (100 MPa), being 88% of the original PEEK substrates. These mechanical properties of PEEK-based PEM are much higher than those of graft-type fluorinated PEM reported previously and almost three times higher than that of Nafion (35 MPa). Wide- and small-angle X-ray scattering (WAXS and SAXS) indicated that the graft polymerization was accompanied with recrystallization of the amorphous phase of PEEK substrate, the well known solvent-induced recrystallization of amorphous PEEK solids, to form a weak lamellar structure with 8 nm spacing. Complementary SAXS and small-angle neutron scattering (SANS) observations clearly showed that the graft-type PEEK membranes possessed ion channel domains with the average distance of 13 nm, being larger than that of Nafion. Furthermore, there was a micro-structure in the ion channels with the average distance of 1.8 nm.     

Synthesis of multi‐block copolymer and its compatibilization to the blends of poly(ether ether ketone) with thermotropic liquid crystalline polymer

A multiblock copolymer (BCP) containing amorphous poly(aryl ether ketone) (PAEK) and thermotropic liquid crystalline polymer (TLCP) segments was synthesized. The chemical structure and properties of BCP were characterized by fourier‐transform infrared spectrometer (FTIR), differential scanning calorimeter (DSC), gel permeation chromatograms (GPC), thermogravimetry analysis, polar light microscope (PLM), and solubility test respectively. BCP can dissolve in chloroform because of soluble PAEK block bonded with TLCP block, which was insoluble. The peak of the original PAEK oligomer was no more present in the GPC traces of the block copolymer. These facts indicated that polymer synthesized should be copolymers of the two components rather than blends. A single T_g at 138.1°C and broad melting endotherm at 315.7°C can be observed. The liquid crystalline texture of BCP showed uniformity in the view after heat treated for 10 min above its T_m under PLM. Ternary blends of poly(ether ether ketone) (PEEK)/TLCP/BCP were prepared by extrusion and characterized by DSC. DSC results showed that the crystallization temperature of PEEK phase in the blends shifted higher with the addition of TLCP. Wide angle X‐ray diffraction investigations indicated that the crystalline structure of PEEK was not disturbed by blending or compatibilizing. Scanning electron microscope and mechanical tests confirmed the compatibilizing effect of BCP. Reduction in dispersed phase TLCP size was observed when 2 phr by weight of compatibilizer was added to the blend. Measurement of the tensile properties showed increased elongation as well as improved modulus and strength to some extent. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Effect of annealing and orientation on microstructures and mechanical properties of polylactic acid

Two types of polylactic acid (PLA) films (one amorphous and one semi‐crystalline) were produced by sheet extrusion. Talc was used as a nucleation agent for the semi‐crystalline PLA. The films were annealed above their T_g or were uniaxially orientated in two ways: (1) via a drawing system in front of the extruder and die or (2) via a three‐roller stretching system. The slower crystallization rate and lower melting stress of the PLA resulted in amorphous film using the drawing system. Annealing above T_g increased crystallinity and polymer chain relaxation, which resulted in increases in both strength and toughness. Stretching above T_g also produced simultaneous crystallization and chain relaxation, which resulted in increases in both modulus and toughness. Both modulus and tensile strength in the stretching direction were higher than in the crosswise direction. Talc acted not only as a rigid filler to reinforce the PLA, but also as a nucleation agent for the PLA, especially during annealing. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

聚醚醚酮薄膜的性能研究

采用挤出流延法制备了一系列聚醚醚酮（PEEK）薄膜，通过拉力机、差示扫描量热仪、紫外分光光度计、透光率雾度仪等对PEEK薄膜的基本性质、光学性能、力学性能进行了研究。结果表明，PEEK薄膜的透光率随结晶度的升高而降低；拉伸速率对拉伸强度、断裂伸长率的影响不大，拉伸速率快，屈服强度明显提高；拉伸强度随流延辊速度的增加而提高；双向拉伸的方法可使薄膜拉伸强度达到203 MPa；增加薄膜厚度、提高结晶度的方法可以提高薄膜的抗紫外性能。     

Synthesis and properties of novel copolymers of poly(ether ketone ether ketone ketone) and poly(ether ketone ketone ether ketone ketone) containing 1,4‐naphthylene moieties

A new monomer, 1,4‐bis(4‐phenoxybenzoyl)naphthalene (BPOBN), was conveniently synthesized via a simple synthetic procedure from readily available materials. A series of novel copolymers of poly(ether ketone ether ketone ketone) and poly(ether ketone ketone ether ketone ketone) containing 1,4‐naphthylene moieties were prepared by the Friedel‐Crafts acylation solution copolycondensation of terephthaloyl chloride (TPC) with a mixture of BPOBN and 4,4′‐diphenoxybenzophenone (DPOBPN), over a wide range of BPOBN/DPOBPN molar ratios, in the presence of anhydrous AlCl₃ and N‐methylpyrrolidone in 1,2‐dichloroethane. The copolymers with 10–40% BPOBN are semicrystalline and had remarkably increased T_gs over the conventional PEEK and PEKK due to the incorporation of 1,4‐naphthylene moieties in the main chains. The copolymers with 30–40 mol% BPOBN had not only high T_gs of 176–177°C, but also moderate T_ms of 332–338°C, which are suitable for the melt processing. These polymers had tensile strengths of 101.5–104.7 MPa, Young's moduli of 2.49–2.65 GPa, and elongations at break of 13.3–15.7% and exhibited high thermal stability and excellent resistance to organic solvents. POLYM. ENG. SCI., 56:566–572, 2016. © 2016 Society of Plastics Engineers     

Preparation and radiation shielding properties of Gd2O3/PEEK composites

Gd₂O₃/PEEK (poly ether ether ketone) composites were prepared on a twin‐screw extruder by the incorporation of Gd₂O₃ as a shield against X‐ray to PEEK matrix. The influence of Gd₂O₃ addition and surface treatment of the particles with sulfonated PEEK (SPEEK) on the morphology, thermal and mechanical properties of the composites was investigated by SEM, DSC, TGA and tensile tests respectively. DSC results showed that both the crystallization temperature (T_c) and melting temperature (T_m) of the composites decreased compared with pure PEEK at random filler content, which suggested that Gd₂O₃ hindered the process of PEEK nucleation. The tensile modulus of the composites increased with addition of Gd₂O₃ and the strain to break decreased. But the tensile modulus and strength of modified series were always higher than that of unmodified ones at the same filler content. The X‐ray shielding properties of composites apparently improved with the increment of the Gd₂O₃. The X‐ray transmittance (A) of 45% S₄GPEEK reduced greatly by about three to eight times compared with PEEKs in all energy range measured. POLYM. COMPOS., 36:651–659, 2015. © 2014 Society of Plastics Engineers     

Synthesis and characterization of poly(ether amide ether ketone)/poly(ether ketone ketone) copolymers

A new monomer, N,N′‐bis(4‐phenoxybenzoyl)‐m‐phenylenediamine (BPPD), was prepared by condensation of m‐phenylenediamine with 4‐phenoxybenzoyl chloride in N,N‐dimethylacetamide (DMAc). A series of novel poly(ether amide ether ketone) (PEAEK)/poly(ether ketone ketone) (PEKK) copolymers were synthesized by the electrophilic Friedel‐Crafts solution copolycondensation of terephthaloyl chloride (TPC) with a mixture of diphenyl ether (DPE) and BPPD, over a wide range of DPE/BPPD molar ratios, in the presence of anhydrous AlCl₃ and N‐methylpyrrolidone (NMP) in 1,2‐dichloroethane (DCE). The influence of reaction conditions on the preparation of copolymers was examined. The copolymers obtained were characterized by different physicochemical techniques. The copolymers with 10–25 mol % BPPD were semicrystalline and had remarkably increased T_gs over commercially available PEEK and PEKK due to the incorporation of amide linkages in the main chains. The copolymers III and IV with 20–25 mol % BPPD had not only high T_gs of 184–188°C, but also moderate T_ms of 323–344°C, having good potential for the melt processing. The copolymers III and IV had tensile strengths of 103.7–105.3 MPa, Young's moduli of 3.04–3.11 GPa, and elongations at break of 8–9% and exhibited outstanding thermal stability and good resistance to organic solvents. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011