Mechanical properties and nonisothermal crystallization of polyamide 6/carbon fiber composites toughened by maleated elastomers

Polyamide 6/carbon fiber (PA6/CF) composites toughened with maleated elastomers were prepared by melt blending using twin‐screw extruder followed by injection molding. Three kinds of maleated elastomers, maleic anhydride (MAH)‐grafted ethylene‐vinyl acetate copolymer (EVA‐g‐MAH), MAH‐grafted ethylene‐propylene‐diene terpolymer (EPDM‐g‐MAH), and MAH‐grafted hydrogenated styrene‐butadiene‐styrene (SEBS‐g‐MAH), were used to toughen the PA6/CF composites. The mechanical properties, morphology, nonisothermal crystallization, and subsequent melting behavior of PA6 hybrid composites were investigated. Mechanical tests indicated that incorporation of elastomers improved the impact properties of CF‐reinforced PA composites accompanied with loss of tensile strength and modulus. It was observed from scanning electron microscope photographs that modification with maleated elastomers improved the interfacial adhesion between the CFs and PA6 matrix. Nonisothermal crystallization behavior showed that three kinds of elastomers had negative effect on crystallization and retarded crystallization of PA6. Kissinger's analysis illustrated that addition of CF slightly increased the crystallization activation energy of PA6, whereas incorporation of elastomers reversed it compared with pure PA6. Furthermore, a slight decrease in crystallinity and melting peak of the composites after incorporation of elastomers was observed compared with pure PA6. Polarizing optical microscope results showed that the transcrystallinity phenomenon seemed to be also affected when the matrix was added by the elastomers. POLYM. COMPOS., 35:2170–2179, 2014. © 2014 Society of Plastics Engineers     

Electrical conductivity and percolation threshold of hybrid carbon/polymer composites

The electrical conductivity and percolation threshold of single and hybrid carbon filled composites are experimentally investigated. Polystyrene, carbon fiber (CF) and carbon black (CB) at three CF/CB ratios of 1.67, 3.33, 6.67 were compounded in a twin screw extruder micro‐compounder and compression molded into sheets. The through‐plane and in‐plane electrical conductivity of the composites are measured by 2 and 4 probe techniques. The percolation threshold of the single filler and hybrid composites are determined from the experimental results using a percolation model. The hybrid composites have a higher value of electrical conductivity and lower percolation threshold than the single CF filler composite except for the CF/CB ratio of 6.67. The percolation threshold for the cases of single filler and hybrid composites are modeled. The hard core / soft shell model is used and it is assumed that the percolation in a particle filled system depends on the ratio of tunneling distance to particle diameter. This ratio is determined by modeling single filler composites using the experimental data and kept constant in the modeling of the hybrid system. Finite size scaling is used to determine the percolation threshold for the infinite size hybrid system containing (nanosize) particles and micron size fibers for three CF/CB ratios. The simulation results show that the percolations of hybrid composites have the same trends observed in the experimental results. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41744.     

Grafting polyamide 6 onto multi‐walled carbon nanotubes using microwave irradiation

Chemical reactions under microwave irradiation can be very efficient, with a significant shortening of reaction time. Few studies have reported the use of microwaves to functionalize carbon nanotubes. In the work reported, a new method of formulating functionalized multi‐walled carbon nanotubes (MWNTs) was developed by covalent grafting of polyamide 6 (PA6) chains onto the carbon nanotubes assisted by microwave irradiation. PA6 chains were grafted onto acidified MWNTs through condensation reaction between the carboxylic groups of the MWNTs and the terminal amine groups of PA6 using microwave radiation heating. The functionalized carbon nanotubes (MWNT‐g‐PA6) were characterized systematically using infrared and Raman spectroscopy, transmission electron microscopy (TEM) and thermogravimetric analysis (TGA). TEM showed that the surface of the MWNTs was covered with a layer of PA6. TGA results indicated that the MWNT‐g‐PA6 contained about 47 wt% of polymer. A novel, convenient and efficient functionalization approach is reported, involving covalently grafting PA6 chains onto MWNTs assisted by microwave irradiation. Copyright © 2010 Society of Chemical Industry     

Styrene‐butadiene‐styrene copolymer compatibilized interfacial modified multiwalled carbon nanotubes with mechanical and piezoresistive properties

In this study, styrene‐butadiene‐styrene tri‐block copolymer/multiwalled carbon nanotubes (SBS/MWNTs) were prepared by means of a solution blending method. To enhance the compatibility between SBS and MWNTs, the SBS grafted MWNTs (SBS‐g‐MWNTs) were used to replace MWNTs. The MWNTs were chemically hydroxylated by the dissolved KOH solution with ethanol as solvent and then reacted with 3‐Aminopropyltriethoxysilane (APTES) to functionalize them with amino groups (MWNT‐NH₂). The SBS‐g‐MWNTs were finally obtained by the reaction of MWNT‐NH₂ and maleic anhydride grafted SBS (MAH‐g‐SBS). The SBS‐g‐MWNTs were characterized by X‐ray photoelectron spectroscopy (XPS), Fourier transform‐infrared spectroscopy (FT‐IR), transmission electron microscopy (TEM), scanning electron microscope (SEM), and thermogravimetric analysis (TGA). The results showed that the SBS molecules were homogeneously bonded onto the surface of the MWNTs, leading to an improvement of the mechanical and electrical properties of SBS/SBS‐g‐MWNTs composites due to the excellent interfacial adhesion and dispersion of SBS‐g‐MWNTs in SBS. A series of continuous tests were carried out to explore the electrical‐mechanical properties of the SBS/SBS‐g‐MWNTs composites. We found out that, near the percolation threshold, the well‐dispersed SBS/SBS‐g‐MWNTs composites showed good piezoresistive characteristics and small mechanical destructions for the development of little deformation under vertical pressure. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42945.     

Improving dispersion of multiwalled carbon nanotubes in polyamide 6 composites through amino‐functionalization

The focus of this study is to investigate the state of dispersion of different treated multiwalled carbon nanotubes (MWNTs) in polyamide 6 (PA6). The MWNTs used in composites were grafted by 1,6‐hexamethylenediamine (HMD) via acid‐thionyl chloride to improve their compatibility with PA6 matrix. A microstructure transformation of MWNTs is found during the treatment process. Acidification makes the MWNTs compact and grafting HMD promotes the compact structure loose again. The MWNTs after different treatment were used to fabricate MWNTs/PA6 composites through melt blending. The dispersion of different MWNTs in PA6 was observed by a combination of scanning electron microscopy, optical microscopy, and transmission electron microscopy. The results show that the amino‐functionalized MWNTs are dispersed more homogeneously in PA6 than the purified MWNTs, and the poorest dispersion is achieved for acid treated MWNTs. It is indicated that the loose structure and functionalized surface of MWNTs benefit the dispersion of MWNTs in PA6. In addition, the amino‐functionalization of MWNTs improves the compatibility between the MWNTs and PA6, resulting in stronger interfacial adhesion. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Electrical and thermal properties of silicone rubber composites filled with Cu-coated carbon fibres and functional carbon nanotubes

ABSTRACT

The thermal and electrical conductivities of SR composites containing Cu-CFs and f-MWNTs were studied. The Cu-CFs and f-MWNTs were prepared by chemical deposition and the coupling method, respectively. Both the fillers were characterised by FT-IR, XRD and SEM and the results showed that the Cu layers were deposited on the surface of the CFs and the MWNTs were successfully modified. In addition, the results of thermal and electrical conductivities for SR composites showed that the hybrid fillers system exhibited a better enhancement on thermal and electrical conductivities for SR composites than the single filler system. The maximum thermal conductivity and the least volume resistivity of SR/Cu-CFs/f-MWNTs composites could reach 3.86?W (m?K)^?1 and 3.5?×?10³?Ω?cm, respectively. Based on the experimental results, we recognised the improvement of intrinsical thermal and electrical conductivities of CFs and the good dispersion of MWNTs contributed to the formation of densified 3D conducting networks. Thus, the hybrid fillers system could synergistically enhance the thermal and electrical conductivities of SR composites. We believe, this study could provide an effective way for the design of high conductive polymer composites.     

High thermal conductive m‐xylylenediamine functionalized multiwall carbon nanotubes/epoxy resin composites

In this study, multiwall carbon nanotubes (MWNTs) functionalized by m‐xylylenediamine is used as thermal conductive fillers to improve their dispersibility in epoxy resin and the thermal conductivity of the MWNTs/bisphenol‐A glycidol ether epoxy resin composites. Functionalization with amine groups of MWNTs is achieved after such steps as carboxylation, acylation and amidation. The thermal conductivity, impact strength, flexural strength, and fracture surfaces of MWNTs/epoxy composites are investigated with different MWNTs. The results show that m‐xylylenediamine is successfully grafted onto the surface of the MWNTs and the mass fraction of the organic molecules grafted onto MWNTs is about 20 wt %. The thermal conductivity of MWNTs/epoxy composites is further enhanced to 1.236 W/mK with 2 wt % m‐MWNTs. When the content of m‐MWNTs is 1.5 wt %, the impact strength and flexural strength of the composites are 25.85 KJ/m², 128.1 MPa, respectively. Scanning electron microscope (SEM) results show that the fracture pattern of composites is changed from brittle fracture to ductile fracture. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41255.     

Conductive network formation and electrical properties of poly(vinylidene fluoride)/multiwalled carbon nanotube composites: Percolation and dynamic percolation

Conductive network formation and its dynamic process for multiwalled carbon nanotubes (MWNTs) and carboxyl‐tethered MWNT (MWNT‐COOH) filled poly(vinylidene fluoride)(PVDF) systems were investigated. Based on real‐time tracing the variation of electrical resistivity of systems with isothermal treatment time, the conductive network formation was evaluated. It was found that the conductive network formation was temperature and time dependent. The percolation time, characterized at a certain annealing time where the electrical resistivity started to decrease drastically, decreased with the increase of the filler concentration or the annealing temperature. However, the values of the percolation time and the activation energy of conductive network formation for the PVDF/MWNT‐COOH system were higher than those of the PVDF/MWNT system, indicating that the interaction between MWNTs and PVDF molecules played an important role in the conductive network formation of the composites. Furthermore, a modified thermodynamic percolation model was proposed to predict the percolation time of PVDF/MWNT composites. It was found that the calculated results fit the experimental data very well. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation and properties of multi‐walled carbon nanotubes/carbon fiber/epoxy composites

Multi‐walled carbon nanotubes/carbon fiber (MWCNTs/CF) hybrid fillers are employed to prepare MWCNTs/CF/epoxy composites. Results reveal that a great improvement of the thermal conductivities of the epoxy composites with the addition of MWCNTs/CF hybrid fillers, and the thermal conductivity of the MWCNTs/CF/epoxy composites is 1.426 W/mK with 8 vol% treated MWCNTs/CF hybrid fillers (5 vol% MWCNTs + 3 vol% CF). Both the flexural and impact strength of the MWCNTs/CF/epoxy composites are increased firstly, but decreased with the excessive addition of MWCNTs. The flexural and impact strength of the MWCNTs/epoxy composites are optimal with 2 vol% MWCNTs. For a given MWCNTs/CF hybrid fillers loading, the surface treatment of MWCNTs/CF hybrid fillers can further increase the thermal conductivities and mechanical properties of the MWCNTs/CF/epoxy composites. POLYM. COMPOS., 35:2150–2153, 2014. © 2014 Society of Plastics Engineers     

Conductive polymer tape containing highly oriented carbon nanofillers

The effect of the orientation of carbon fillers with different aspect ratios on the resistivity and morphology of conductive polymer composites (CPCs) based on polypropylene was investigated in this study. Multiwall carbon nanotubes (MWNTs) and carbon black (CB) were used as conductive fillers. The CPCs were made by melt compounding, hot pressing, and solid‐state drawing. The alignment of the filler was observed after solid‐state drawing. The resistivity of the composites increased with the draw ratio at relatively low carbon filler loadings (<20 wt %), whereas it remained unchanged at a high filler loading (20 wt % CB). Orientation‐promoted anisotropy of the conductive network was observed in both the morphology and resistivity. MWNTs were found to be better at maintaining a percolating network under large deformations than CB because of their larger aspect ratio and their entangled network structure. The experimentally obtained resistivity was analyzed with percolation theory, and this indicated that the initial three‐dimensional conductive network was deformed into a two‐dimensional network after solid‐state drawing for the composites containing CB. The three‐dimensional network was found in isotropic CPCs containing MWNTs with the same analysis. Theoretical analysis using excluded volume theory was in good agreement with results obtained experimentally. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation and properties of epoxy/BN highly thermal conductive composites reinforced with SiC whisker

A simple method is reported to increase the thermal conductivity and improve the poor mechanical properties caused by high filler loadings of epoxy composites, simultaneously. Epoxy composites were prepared with micro‐boron nitride (BN) and silicon carbon whisker (SiCw) chemically treated by 3‐aminopropyltriethoxysilane (KH550) and 3‐glycidyloxypropyltrimethoxysilane (KH560), respectively. Effects of surface modification of BN particles on the thermal conductivity and flexural strength of epoxy/BN composites were investigated. About 3% SiCw particles grafted with KH560 were incorporated into composites with BN grafted with KH550, which led to about 13.8–17.8% increase of the flexural strength as well as a marginal improvement of the thermal conductivity of composites, and they possessed good dielectric properties. In addition, dynamic mechanical analysis results showed that the storage modulus of composites increased significantly with the addition of fillers, while the glass transition temperature exhibited a slight decrease. POLYM. COMPOS., 37:2611–2621, 2016. © 2015 Society of Plastics Engineers     

Incorporation of 4‐aminobenzene functionalized multi‐walled carbon nanotubes in polyaniline for application in formic acid electrooxidation

Incorporation of carbon nanotubes (CNTs) in conducting polymer can lead to new composites with enhanced electrical and mechanical properties. However, the development of such composites has been hampered by the inability to disperse CNTs in polymer matrix due to the lack of chemical compatibility between polymers and CNTs. Covalent sidewall functionalization of carbon nanotube provides a feasible route to incorporate carbon nanotube in polymer. In this work, 4‐aminobenzene groups were grafted onto the surface of multi‐walled carbon nanotube (MWNT) via C? C covalent bond. Polyaniline (PANI)/MWNT composites were fabricated by electrochemical polymerization of aniline containing well‐dissolved functionalized MWNTs. The obtained composites can be used as catalyst supports for electrooxidation of formic acid. Cyclic voltammogram results show that platinum particles deposited in PANI/MWNT composite films exhibit higher electrocatalytic activity and better long‐term stability towards formic acid oxidation than that deposited in pure PANI films. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Isothermal crystallization kinetics and melting behavior of multiwalled carbon nanotubes/polyamide‐6 composites

Pristine and functionalized multiwalled carbon nanotubes (MWNTs) were used to fabricate polyamide 6 (PA6) composites through melt blending. The functionalized MWNTs were obtained by grafting 1,6‐hexamethylenediamine (HMD) onto the pristine MWNTs to improve their compatibility with PA6 matrix. The effect of MWNTs on the isothermal crystallization and melting behavior of PA6 was investigated by differential scanning calorimetry (DSC) and X‐ray diffraction (XRD). The Avrami and Lauritzen–Hoffmann equations are used to describe the isothermal crystallization kinetics. The values of the Avrami exponent found for neat PA6, the pristine MWNTs/PA6 and functionalized MWNTs/PA6 composite samples are about 4.0, 1.7, and 2.3, respectively. The activation energies are determined by the Arrhenius method, which is lower for the composites, ?320.52 KJ/mol for pristine MWNTs/PA6 and ?293.83 KJ/mol for functionalized MWNTs/PA6, than that for the neat PA6 (?284.71 KJ/mol). The following melting behavior reveals that all the isothermally crystallized samples exhibit triple melting endotherms at lower crystallization temperature and double melting endotherms at higher crystallization temperature. The multiple melting endotherms are mainly caused by the recrystallization of PA6 during heating. The resulting equilibrium melting temperature is lower for the composites than for neat PA6. In addition, polarizing microscopy (PLM) and small angle light scanning (SALS) were used to study the spherulite morphology. The results show that the MWNTs reduce the spherulite radius of PA6. This reduction is more significant for pristine MWNTs. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Properties of ultrahigh‐molecular‐weight polyethylene nanocomposite films containing different functionalized multiwalled carbon nanotubes

We compared the thermomechanical properties, morphologies, gas permeabilities, and electrical conductivities of ultrahigh‐molecular‐weight polyethylene (UHMWPE) nanocomposite films containing two types of functionalized multiwalled carbon nanotubes (functionalized MWNTs). Both 2‐hydroxyethyl triphenyl phosphonium‐MWNT (Ph3P‐MWNT) and 1,1,1,3,3,3‐hexafluoro‐2‐phenyl‐2‐propanol‐MWNT (CF3‐MWNT) were used as reinforcing fillers in the fabrication of UHMWPE hybrid films. UHMWPE nanocomposites with various functionalized MWNT contents were solution‐cast to produce the films. The thermomechanical properties and morphologies of the UHMWPE hybrid films were then characterized using differential scanning calorimetry, thermogravimetric analysis, electron microscopy, and mechanical tensile analysis. Transmission electron microscopy studies showed that some of the MWNT particles were dispersed homogeneously within the polymer matrix (on the nanoscale), whereas others were agglomerated. We also found that the addition of only a small amount of functionalized MWNTs was sufficient to improve the thermomechanical properties and the gas barrier of the UHMWPE hybrid films. Even, those hybrid films with low functionalized MWNT contents (i.e., <1 wt%) were found to exhibit much better thermomechanical properties than the pure UHMWPE films. On the other hand, the values of the electrical conductivity remained constant, regardless of the amount of functionalized MWNTs. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Electrical conductivity and thermal properties of acrylonitrile‐butadiene‐styrene filled with multiwall carbon nanotubes

Composites of Acrylonitrile‐butadiene‐styrene (ABS) and multiwall carbon nanotubes (MWNTs) have been prepared via solution‐blending. The electrical conductivity of these composites is analyzed. The MWNT‐filled ABS shows percolation point of the electrical conductivity at low filler loadings (1–2 wt%). The micro‐structure of the composites is also analyzed by scanning electron microscopy showing that the nanotubes are dispersed quite homogeneously in the polymer‐matrix. The thermogravimetric analysis is used to study the thermal degradation of ABS/MWNTs composites in nitrogen. MWNTs tend to destabilize the ABS matrix in the 220–450°C degradation regions but improve the thermal stability in the 425–850°C regions. With further addition of MWNTs, the features of the destabilization in the 220–450°C degradation region did not change much but in the 425–850°C degradation process, the MWNTs reinforced stabilization and the quality of the char residue of amorphous carbon deposition was improved. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Functionalizing carbon nanotubes by grafting cyclotriphosphazene derivative to improve both mechanical strength and flame retardancy

An intumescent flame‐retardant, hex(4‐carboxylphenoxy) cyclotriphosphazene (HCPCP) was synthesized and covalently grafted on to the surface of multiwalled carbon nanotubes (MWNTs) to obtain MWNT‐HCPCP. MWNT/epoxy resin (EP) and MWNT‐HCPCP/ EP nanocomposites were prepared via thermal curing. Transmission electron microscopy results showed that a core–shell structure with MWNTs as the hard core and HCPCP as the soft shell were formed after HCPCP (10 wt%) were attached to the MWNTs. The results of flammability tests showed an increased limited oxygen index value for MWNT‐HCPCP/EP nanocomposites. The mechanical properties including tensile strength and elongation were both dramatically improved due to the better dispersion of MWNT‐HCPCP in the EP matrix. The grafting of HCPCP can improve both the dispersion of nanotubes in polymer matrix and flame retardancy of the nanocomposites. POLYM. COMPOS., 35:2187–2193, 2014. © 2014 Society of Plastics Engineers     

Improvement of thermo-electrical properties of polymer composites filled with multiwall carbon nanotubes decorated carbon fillers

To enhance the thermo-electrical properties of liquid silicone rubber (LSR) in applications, the carbon fibres (CFs) modified by multiwall carbon nanotubes (MWCNT) on the surfaces were used as the fillers. The MWCNT-modified CFs (MPCFs) were analysed by Fourier transform infrared spectra, thermogravimetric analysis, scanning electron micrograph and energy dispersive X-ray spectroscopy. It was found that MWCNT were successfully adsorbed onto the surface of CFs. The MPCFs functioned as conductive fillers in LSR for thermal and electrical conductivity application and exhibited significant enhancement. The effects of MPCFs loading on thermal conductivity and volume resistivity of LSR composites were investigated in detail. Results of this work revealed that the MPCFs/LSR composites possessed a thermal conductivity of 0.73?W?m^?1?K^?1 with 14?vol.-% filler loading, approximately 3.48-fold higher than that of pure LSR substrate. And with the increase of MPCFs loading, the least volume resistivity of MPCFs/LSR composites is 10?Ω?cm. Besides, compared with that of neat LSR, the tensile strength of MPCFs/LSR composites increased 0.913?MPa.     

Silica and diatomite fillers modified fluorine rubber composites treated by silane‐coupling agents

The fluorine rubber nanocomposites were prepared by using the silane‐coupling agents treated silica and diatomite, in which 3‐amino propyltriethoxysilane (KH550), 3‐mercapto‐propyl trimethoxysilane (KH590), and bis‐(γ‐triethoxysilylpropyl)‐tetrasulfide (Si69) of the coupling agent were used as the filler modifiers to increase the compatibility between filler and fluorine rubber. The structure and morphology of the composites were investigated by Fourier transform infrared spectroscopy and scanning electron microscopy. The T_g and thermal stability of the composites were investigated by dynamic mechanical analysis and thermogravimetric analysis. The results showed that the best coupling agent was KH550 and 2 phr (parts per hundred rubber). The KH550‐modified compound filler was crosslinked with fluorine rubber, and the compatibility between filler and fluorine rubber was improved and further confirmed to improve the thermal properties of fluorine rubber with the KH550‐modified filler. J. VINYL ADDIT. TECHNOL., 26:55–61, 2020. © 2019 Society of Plastics Engineers     

Effects of sizing materials on the properties of carbon fiber‐reinforced polyamide 6,6 composites

This article aims to study the effect of the sizing materials type on the mechanical, thermal, and morphological properties of carbon fiber (CF)‐reinforced polyamide 6,6 (PA 6,6) composites. For this purpose, unsized CF and sized CFs were used. Thermogravimetric analysis was performed, and it has been found that certain amounts of polyurethane (PU) and PA sizing agents decompose during processing. The effects of sizing agent type on the mechanical and thermomechanical properties of all the composites were investigated using tensile, Izod impact strength test, and dynamic mechanical analysis. Tensile strength values of sized CF‐reinforced composites were higher than that of unsized CF‐reinforced composites. PA and polyurethane sized CF‐reinforced composites exhibited the highest impact strength values among the other sized CF‐reinforced composites. PU and PA sized CF‐reinforced composites denoted higher storage modulus and better interfacial adhesion values among the other sizing materials. Scanning electron microscope studies indicated that CFs which were sized with PU and PA have better interfacial bonding with PA 6,6 matrix among the sized CFs. All the results confirmed that PA and PU were suitable for CF's sizing materials to be used for PA 6,6 matrix. POLYM. COMPOS., 34:1583–1590, 2013. © 2013 Society of Plastics Engineers     

Fabrication of hybrid ladderlike polysilsesquioxane‐grafted multiwalled carbon nanotubes

Ladderlike polysilsesquioxanes (LPSs) containing chloromethylphenyl groups were synthesized from (p‐chloromethyl)phenyltrimethoxysilane under basic conditions. Functionalized multiwalled carbon nanotubes (MWNT–COOH) were prepared by the acid treatment of pristine multiwalled carbon nanotubes (MWNTs). MWNT–COOH was reacted with LPS to prepare LPS‐grafted MWNTs via ester linkages. The functionalization of MWNTs with LPS significantly altered the surface roughness of the MWNTs; there was a significant increase in the diameter of the MWNTs. The LPS‐grafted MWNTs had a 10–20 nm thickness along the outer walls according to the functionalization of the MWNTs with LPS. An advantage of the hybrid LPS‐grafted MWNTs was shown as improved thermal behavior. The composition, thermal properties, and surface morphology of the LPS‐grafted MWNTs were studied by Fourier transform infrared spectroscopy, thermogravimetric analysis, energy‐dispersive spectroscopy, scanning electron microscopy, atomic force microscopy, and transmission electron microscopy. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012