Crystal phase transition dependence of the energy storage performance of poly(vinylidene fluoride) and poly(vinylidene fluoride‐hexafluoropropene) copolymers

Large‐scale mechanical stretching has been performed to modify the crystal phase structures of the pristine poly(vinylidene fluoride) (PVDF) and its copolymer poly(vinylidene fluoride‐hexafluoropropylene) [P(VDF‐HFP)] with various molar contents HFP in an attempt to improve their energy storage performances. It is found that the physical stretched PVDF and P(VDF‐HFP) 95.5/4.5 mol % films have a phase transition from the nopolar α‐phase to highly polar β‐phase, which is different from the P(VDF‐HFP) films with relative high HFP molar contents (α to γ phases). The following results show that the phase transition in these PVDF‐based polymers has a significant effect on their dielectric and energy storage performances. On account of the reformation of the crystalline property and elimination of the impurity defects, an ultra‐high breakdown electric field of ∼900 MV/m has been obtained in all the stretched samples. Consequently, the higher discharged energy densities of 27.1 and 27.7 J/cm³ are calculated from the D–E loops of the β‐PVDF and β‐P(VDF‐HFP) 95.5/4.5 mol % films, respectively. Regarding their excellent discharging energy density of ∼10 J/cm³ under 600 MV/m for thousands of times, the stretched PVDF and its copolymer P(VDF‐HFP)s are promising candidates for high power capacitors applications. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46306.     

Dielectric and conducting behavior of pyrene functionalized PANI/P(VDF‐co‐HFP) blend

Herein, we present the dielectric and electrical conductivity properties of the partially miscible polymer blend prepared using pyrene functionalized polyaniline (pf‐PANI) and poly(vinylidene fluoride‐co‐hexafluoro propylene) (PVDF‐co‐HFP). The blend mostly retains the fluorescent nature of pf‐PANI as well as can be moldable and possesses good damping property. The dielectric properties have been investigated as a function of temperature at three different frequencies and the plausible origin of polarization responsible for dielectric behavior in this blend has been identified. The experimental results of dielectric measurements are compared with theoretical models and discussed. The surface morphology of the samples has been examined with a scanning electron microscope. The electrical conductivity has also been studied as a function of temperature and explained in terms of hopping of charge carriers/interconnected networks. The combined dielectric and conductivity results together with scanning electron microscope micrographs, reveal that there is hindrance to achieve percolation threshold even after pf‐PANI addition of 57 vol % and subsequent thermal treatment. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44077.     

Lewis acid–base property of P(VDF‐co‐HFP) measured by inverse gas chromatography

Poly (vinylidene fluoride‐co‐hexafluoropropylene) P(VDF‐co‐HFP) is an excellent material for polymer electrolytes of lithium ion battery. To enhance the lithium ion transference number, some metal oxides were often embedded into P(VDF‐co‐HFP). The promising mechanism for the increase in lithium ionic conductivity was Lewis acid‐base theory. In this experiment, the Lewis acid–base properties of P(VDF‐co‐HFP) were measured by inverse gas chromatography (IGC). The Lewis acid constant K_a of P(VDF‐co‐HFP) is 0.254, and the base constant K_b is 1.199. Compared with other polymers characterized by IGC, P(VDF‐co‐HFP) is the strongest Lewis basic polymers. Except aluminum ion, lithium ion is the strongest Lewis acidic ion according to their η value of Lewis acids. Therefore, a strong Lewis acid–base interaction will exist between lithium ion and P(VDF‐co‐HFP). This will restrict the transference of lithium ion in P(VDF‐co‐HFP). To enhance the lithium ion transference by blending other metal ions into P(VDF‐co‐HFP), it is suggested that the preferential ions should be Al³⁺, Mg²⁺, Na⁺, and Ca²⁺ because these metal ions have relative large η values. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Grafting of 4‐Hydroxybenzenesulfonic Acid onto Commercially Available Poly(VDF‐co‐HFP) Copolymers for the Preparation of Membranes

The grafting of a phenate bearing sulfonate group in solution onto commercially available poly(VDF‐co‐HFP) copolymers, where VDF and HFP stand for vinylidene fluoride and hexafluoropropene, respectively, is presented. This reaction leads to novel fluoropolymers, bearing aryl sulfonic acid side functions, which are fuel cell membrane precursors. A mechanism similar to the grafting of bisphenol onto VDF‐containing copolymers is discussed. First, the sulfonate phenate is modified to give the didecyldimethylammonium bromide sulfonate phenate salt, in order to promote the substitution onto a fluorine atom in VDF unit adjacent to one HFP unit onto a fluorine atom in the copolymer. The substitution of this salt onto the fluorinated copolymer yields low molar percentages of grafted phenate, ranging from 1.8 to 5.1 mol‐%, whereas it reaches values up to 13 mol‐% grafting when the NH₂‐CH₂‐CH₂‐S‐CH₂‐CH₂‐C₆H₄‐SO₃Na amine is used as the grafting agent. NMR characterization is used to monitor the grafting process. The electrochemical properties of the resulting phenate grafted‐poly(VDF‐co‐HFP) copolymer are studied. The theoretical ion exchange capacities are half that of Nafion®. The proton conductivities are also lower than that of Nafion®, although one conductivity measurement reached a value of 5.1 mS cm^–1, showing a non‐negligible conductivity. The water uptake is lower than these noted for a sulfonated amine‐grafted copolymer, and is of the same order as that for Nafion®. Finally, it is shown that these novel materials start to decompose above 200 °C, showing a similar thermostability as that of an amino‐containing aryl sulfonate‐grafted poly(VDF‐co‐HFP) copolymer.     

Preparation and properties of alkaline anion exchange membrane with semi‐interpenetrating polymer networks based on poly(vinylidene fluoride‐co‐hexafluoropropylene)

Alkaline anion exchange membrane with semi‐interpenetrating polymer network (s‐IPN) was constituted based upon quaternized poly(butyl acrylate‐co‐vinylbenzyl chloride) (QPBV) and poly(vinylidene fluoride‐co‐hexafluoropropylene) [P(VDF‐HFP)]. The QPBV was synthesized via the free radical copolymerization, followed by quaternization with N‐methylimidazole. The s‐IPN system was constituted by melting blend of QPBV and P(VDF‐HFP), and then crosslinking of P(VDF‐HFP). Ion exchange capacity, water uptake, mechanical performance, and thermal stability of these membranes were characterized. TEM showed that alkaline anion exchange membrane exhibited s‐IPN morphology with microphase separation. The fabricated s‐IPN membrane exhibited hydroxide ion conductivity up to 15 mS cm^?1 at 25 °C and a maximum DMFC power density of 46.55 mW cm^?2 at a load current density of 98 mA cm^?2 at 30 °C. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45775.     

Preparation and performance study on P(St‐MMA)‐SiO2 doped P(VDF‐HFP) based composite polymer electrolyte

The organic–inorganic hybrid material poly(styrene‐methyl methacrylate)‐silica (P(St‐MMA )‐SiO₂) was successfully prepared by in situ polymerization confirmed by Fourier transform infrared spectroscopy and was employed to fabricate poly(vinylidene fluoride‐hexafluoropropylene) (P(VDF‐HFP )) based composite polymer electrolyte (CPE ) membrane. Desirable CPEs can be obtained by immersing the CPE membranes into 1.0 mol L^?1 LiPF₆‐EC /DMC /EMC (LiPF₆ ethylene carbonate + dimethyl carbonate + ethylmethyl carbonate) liquid electrolyte for about 0.5 h for activation. The corresponding physicochemical properties were characterized by SEM , XRD , electrochemical impedance spectroscopy and charge–discharge cycle testing measurements. The results indicate that the as‐prepared CPEs have excellent properties when the mass ratio of the hybrid P(St‐MMA )‐SiO ₂ particles to polymer matrix P(VDF‐HFP ) reaches 1:10, at which point the SEM analyses show that the as‐prepared P(St‐MMA )‐SiO ₂ particles are uniformly dispersed in the membrane and the CPE membrane presents a homogeneous surface with abundant interconnected micropores. The XRD results show that there may exist interaction forces between the P(St‐MMA )‐SiO ₂ particles and the polymer matrix, which can obviously decrease the crystallinity of the composite membrane. Moreover, the ionic conductivity at room temperature and the electrochemical working window of the CPE membrane can reach 3.146 mS cm^?1 and 4.7 V, respectively. The assembled LiCoO₂/CPE /Li coin cell with the CPE presents excellent charge–discharge and C ‐rate performance, which indicates that P(St‐MMA )‐SiO ₂ hybrid material is a promising additive for the P(VDF‐HFP ) based CPE of the lithium ion battery. © 2016 Society of Chemical Industry     

Electrochemical synthesis of poly(2‐iodoaniline) and poly(aniline‐co‐2‐iodoaniline) in acetonitrile

Poly(2‐iodoaniline) (PIANI) and poly(aniline‐co‐2‐iodoaniline) [P(An‐co‐2‐IAn)] were synthesized by electrochemical methods in acetonitrile solution containing tetrabutylammonium perchlorate (TBAP) and perchloric acid (HClO₄). The voltametry of the copolymer shows characteristics similar to those of conventional polyaniline (PANI), and it exhibits higher dry electrical conductivity than PIANI and lower than PANI. The observed decrease in the conductivity of the copolymer relative to PANI is attributed to the incorporation of the iodine moieties into the PANI chain. The structure and properties of these conducting films were characterized by FTIR and UV‐Vis spectroscopy and by an electrochemical method (cyclic voltametry). Conductivity values, FTIR and UV‐Vis spectra of the PIANI and copolymer were compared with those of PANI and the relative solubility of the PIANI and the copolymer powders was determined in various organic solvents. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1652–1658, 2003     

An EPR investigation of conductive polyaniline–poly(methyl methacrylate‐co‐acrylic acid) blends

A conductive blend of polyaniline (PANI) with sodium form poly(methyl methacrylate‐co‐acrylic acid) copolymer (PMMAA) was prepared by in situ dispersion polymerization. The PANI‐PMMAA blends were characterized with UV–vis, FTIR, and electron paramagnetic resonance (EPR) spectra. The effects of PANI and temperature on the electronic properties of the PANI‐PMMAA blends were studied with EPR technique. The PANI and temperature affect the intermolecular interaction between PANI and PMMAA and then determines the EPR parameters (A/B ratio, g factor, T₂, ΔH_pp, N_s, and lineshape). POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Enhancement of dielectric and energy density properties in the PVDF‐based copolymer/terpolymer blends

We investigated the high dielectric constant and energy storage density for the blends of P(VDF‐TrFE) copolymer and P(VDF‐TrFE‐CFE) terpolymer. The degradation of coercive field (E_c) and remnant polarization (P_r) of the copolymer under an electric field of 125 MV/m was observed and the copolymer changed into a typical relaxor ferroelectric with doping of terpolymer. The dielectric constant of P(VDF‐TrFE) was found to be ～11, but was enhanced to ～55 by blending with P(VDF‐TrFE‐CFE) at 60 wt%. Consequently, a higher energy density of about 4.2 J/cm³ was obtained in these blends in contrast to about 3.6 J/cm³ in the terpolymer at the very low applied electric field of 125 MV/m. These results demonstrate the promise of blend approaches for tailoring and enhancing the dielectric properties of ferroelectric polymers. POLYM. ENG. SCI., 55:1396–1402, 2015. © 2015 Society of Plastics Engineers     

Effect of various electrophoretically deposited nano‐silica contents on the properties of poly(vinylidene fluoride‐co‐hexafluoropropylene)‐based electrospun polymer electrolytes

Poly(vinylidene fluoride‐co‐hexafluoropropylene) (P(VDF‐HFP)) based composite polymer electrolyte (CPE) membranes were successfully prepared by electrospinning followed by electrophoretic deposition processes, and desirable polymer electrolytes were obtained after being activated in liquid electrolytes. The physicochemical properties of the CPEs with different electrophoretically deposited nano‐SiO₂ contents were investigated by SEM, XRD, TGA, linear sweep voltammetry and electrochemical impedance spectroscopy measurements. When the ratio of electrophoretically deposited nano‐SiO₂ to P(VDF‐HFP) is up to 4 wt%, the results show that the CPE membrane presents a very uniform surface with abundant interconnected micropores and possesses excellent mechanical tensile strength with high thermal and electrochemical stability; the ionic conductivity at room temperature can reach 3.361 mS cm^?1 and the reciprocal temperature dependence of the ionic conductivity follows a Vogel ? Tamman ? Fulcher relationship. The interfacial resistance of the assembled Li/CPE/Li simulated cell can rapidly increase to a steady value of about 950 Ω from the initial value of about 700 Ω at 30 °C during 15 days' storage. The battery performance test suggests that the CPE also shows excellent compatible properties with commercial LiCoO₂ and graphite materials. © 2015 Society of Chemical Industry     

Impact of preparation method on physical properties and gas separation performance of fluorinated copolymer membranes

Two batches of poly(vinylidene fluoride–hexafluoropropylene) [P(VDF–HFP)] copolymer with different monomer ratios were thoroughly characterised and cast into membranes to relate the fundamental properties of this copolymer with its performance in CO₂ separation. Solubility testing revealed that the PVDF part of the copolymer was dominating and calculations with Hansen’s solubility parameters corroborated the outcome. A very slow solvent evaporation rate and use of solvents with a high boiling point were found to be essential in the formation of defect-free membranes from this copolymer for gas separations. Physical examination, DSC, XRD and TGA were also performed to better link the fundamental membrane properties to the gas separation performance. A low crystallinity in the prepared P(VDF–HFP) membranes was favourable in terms of compatibility, solubility, membrane formation and CO₂ separations.     

Dielectric relaxation in vinylidene fluoride–hexafluoropropylene copolymers

The molecular mobility in copolymers of vinylidene fluoride–hexafluoropropylene VDF/HFP of 93/7 and 86/14 ratios has been investigated by means of broadband dielectric relaxation spectroscopy (10^?1–10⁷ Hz), differential scanning calorimetry DSC (?100 to 150°C), and of wide angle X‐ray diffraction WAXS. Four relaxation processes and one ferroelectric‐paraelectric phase transition have been detected. The process of the local mobility β‐ (at temperatures below glass transition point) is not affected by chemical composition of the copolymer and the formed structure. Parameters of segmental mobility in the region of glass transition (α_a‐relaxation) depend on the ratio of comonomer with lower kinetic flexibility. α_c‐relaxation is clearly observed only in VDF/HFP 93/7 copolymer, which is characterized by a higher crystallinity and a higher perfection of crystals of α‐ (α_p‐) phase. Diffuse order–disorder relaxor type ferroelectric transition connected with the destruction of the domains in low‐perfect ferroelectric phase in the amorphous regions has been detected for both copolymers. An intensive relaxation process (α‐process) was observed for both copolymers in high‐temperature region. DSC data shows that it falls on the broad temperature region of α‐phase crystals melting. It is considered to be connected with the space charge relaxation. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Annealing effect on poly(vinylidene fluoride/trifluoroethylene) (70/30) copolymer thin films above the melting point

To further understand crystallization behaviors above the melting temperature (T_m), the morphologies and structure of ferroelectric poly(vinylidene fluoride/trifluoroethylene) [P(VDF–TrFE); 70/30] copolymer films at different temperatures were studied by atomic force microscopy, differential scanning calorimetry, and X‐ray diffraction (XRD). We found that there was a structural change in the P(VDF–TrFE) copolymer film above T_m, which corresponded to the transition from tightly arrayed grains to fiberlike crystals. For the samples annealed above T_m, heat treatment reduced the density of gauche defects and caused a better arrangement of the crystalline phase. So those samples were in the ferroelectric phase without gauche defects, with one sharp diffraction peak reflected in the XRD curves. It was helpful to further make clear the thermal behaviors from the melts of the P(VDF–TrFE) copolymers and discuss their application under higher temperatures. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Polyaniline with high crystallinity degree: Synthesis,structure, and electrochemical properties

Polyaniline (PANI) with high crystallinity degree was facilely synthesized on the surface of stainless steel net by galvanostatic method. The effect of polymerization current density on the characteristics of morphology and structure had been investigated by field emission scanning electron microscopy (FE‐SEM), Fourier transforms infrared (FTIR), X‐ray photoelectron spectroscopy (XPS), and X‐ray diffraction (XRD). FE‐SEM observations disclosed that PANI was deposited as nanofibers and their diameters decreased with the polymerization current density. FTIR studies revealed that degree of oxidation increased in order PANI‐2 < PANI‐6 < PANI‐10. XPS measurements displayed that PANI polymerized at 6 mA cm^?2 (PANI‐6) exhibited much higher doping level of 77.8%, which favored the conductivity. XRD analysis discovered that the obtained PANI showed high crystallinity degree in which PANI‐6 possessed highest crystallinity degree (X_cr) up to 67%. Electrochemical performances of PANI as electrode materials were studied via cyclic voltammetry. The results presented that PANI‐6 possessed greater discharge capacity and better reversibility. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40827.     

Synthesis and ferroelectric investigations of poly(vinylidene fluoride‐co‐hexafluoropropylene)‐Mg(NO3)2 films

The free‐standing, flexible, and ferroelectric films of poly(vinylidenefluoride‐co‐hexafluoropropylene) [P(VDF‐HFP)] were prepared by spin coating method. The ferroelectric phase of the films was enhanced by adding magnesium nitrate Mg(NO₃)₂ in different wt % as the additive during the film fabrication. The effects on the structural, compositional, morphological, ferroelectric, dielectric, and leakage current behaviors of the films due to the addition of salt were analyzed. Based on the X‐ray diffraction (XRD) patterns and Fourier Transform Infrared (FTIR) spectra, it is confirmed that the addition of Mg(NO₃)₂ promotes the electroactive β phase that induces the ferroelectric property. The fiber‐like topography of the films exhibits a nodule‐like structure, and the roughness of the films increases by the addition of Mg(NO₃)₂. The ferroelectric studies show the higher polarization values for the composite films than that of the plain P(VDF‐HFP) film. The Piezo‐response force microscope images also confirm the domain switching behavior of the samples. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44008.     

Miscibility and morphology of poly(vinylidene fluoride)/poly[(vinylidene fluoride)‐ran‐trifluorethylene] blends

This study presents an investigation of the effect of the different crystalline phases of each blend component on miscibility when blending poly(vinylidene fluoride) (PVDF) and its copolymer poly[(vinylidene fluoride)‐ran‐trifluorethylene] [P(VDF–TrFE)] containing 72 mol % of VDF. It was found that, when both components crystallized in their ferroelectric phase, the PVDF showed a strong effect on the crystallinity and phase‐transition temperature of the copolymer, indicating partial miscibility in the crystalline state. On the other hand, immiscibility was observed when both components, after melting, were crystallized in their paraelectric phase. In this case, however, a decrease in crystallization temperatures suggested a strong interaction between monomers in the liquid state. Blend morphologies indicated that, in spite of the lack of miscibility in the crystalline state, there is at least miscibility between PVDF and P(VDF–TrFE) in the liquid state, and that a very intimate mixture of the two phases on the lamellar level can be maintained upon crystallization. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1362–1369, 2002     

Electrical energy discharging performance of poly(vinylidene fluoride‐co‐trifluoroethylene) by tuning its ferroelectric relaxation with polymethyl methacrylate

Poly(methyl methacrylate) (PMMA) was introduced into ferroelectric Poly(vinylidene fluoride‐co‐trifluoroethylene) P(VDF‐co‐TrFE) via a simple solution blending process and a series of P(VDF‐co‐TrFE)/PMMA blends with varied PMMA content was obtained in an effort to investigate the confinement effect of PMMA on the crystalline, dielectric, and electric energy storage properties of P(VDF‐co‐TrFE). PMMA addition could reduce the crystallinity dramatically as well as the crystal size due to its dilution effect and impediment effect on the crystallization of P(VDF‐co‐TrFE). PMMA introduction is also responsible for the phase transition of P(VDF‐co‐TrFE) from α phase into γ phase. As expected, both the dielectric constant and loss of the blends are reduced as PMMA addition increases for the dilute, decoupling, and confinement effect of PMMA on the relaxation behavior of crystal phases of P(VDF‐co‐TrFE) under external electric field. As a result, both the maximum and remnant polarization of the blends are significantly depressed. The irreversible polarization of P(VDF‐co‐TrFE) is effectively restricted by the addition of PMMA due to its impeding effect on the crystallization of P(VDF‐co‐TrFE) and restricting effect on the switch of the polar crystal domains. Therefore, the energy loss induced by the ferroelectric relaxation of P(VDF‐co‐TrFE) is significantly reduced to less than 25% at an electric field of 450 MV/m while the energy storage density is well maintained at about 10 J/cm^?3 in the blend with 30 wt % PMMA. The results may help to understand how the ferroelectric relaxation affects the energy loss of ferroelectrics fundamentally and design more desirable materials for high energy storage capacitors. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40114.     

Curing behavior and properties of benzoxazine‐co‐self‐promoted phthalonitrile polymers

A new high‐performance copolymer was successfully obtained via concerted catalysis polymerization of mono‐functional benzoxazine (P‐a) and self‐promoted 4‐aminophenoxy phthalonitrile (4‐APN) monomers. The FTIR and DSC curves of the P‐a/4‐APN in different blend ratios suggested that the monomer blends can be completely cured without the addition of curing additive. The P‐a/4‐APN copolymers were cured at relatively lower curing temperatures and time. The TGA curves revealed that the P‐a/4‐APN copolymers have good thermal stability in terms of T₅, T₁₀, and char yield. A gradual increase in the glass transition temperature (T_g) values and decline were seen in the storage modulus as the loading of 4‐APN was increased from 10 to 30 wt % in the copolymer. The SEM analyses showed that copolymer's fracture surface is dendritic, showing the stress has been dispersed to a certain extent. The study revealed that the poly(P‐a/4‐APN) copolymer have much better thermal stabilities than the poly(P‐a), and the prepared copolymer can be used as a high‐performance thermosetting resin. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46578.     

Development of a conjugated polyaniline incorporated electrospun poly(vinylidene fluoride‐co‐hexafluoropropylene) composite membrane electrolyte for high performance dye‐sensitized solar cells

Different weight percentage (2, 3, 4, and 5 wt %) of polyaniline (PANI) were incorporated into electrospun poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVdF‐HFP) composite membranes (esCPMs). The regular morphology, molecular structure, crystallinity, porosity, electrolyte uptake, and leakage of the composite membranes were examined. The esCPMs were activated in liquid electrolyte containing 0.5 M LiI, 0.05 M I₂, and 0.5 M 4‐tert‐butylpyridine and 0.5 M 1‐butyl‐3‐methylimidazoliun iodide in acetonitrile to afford electrospun PVdF‐HFP/PANI composite membrane electrolytes (esCPMEs). The influence of different wt % of PANI on the esCPMEs was studied by electrochemical impedance measurements and Tafel polarization studies. The photovoltaic performance of a dye‐sensitized solar cell assembled using 3 wt % PANI incorporated esCPME exhibits a higher power conversion efficiency of 7.20% than that assembled using esPME (η = 6.42%). © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42777.     

Preparation of monodispersed ZrO2 nanoparticles and their applications in poly[(vinylidene fluoride)‐co‐hexafluoropropylene]‐based composite polymer electrolytes

To improve the electrochemical performance of pure poly[(vinylidene fluoride)‐co‐hexafluoropropylene] (P(VDF‐HFP))‐based gel polymer electrolytes, different amounts of monodispersed ZrO₂ nanoparticles were introduced to fabricate P(VDF‐HFP)/ZrO₂ composite polymer electrolytes (CPEs) using the phase inversion method and activated processes, in which the monodispersed ZrO₂ nanoparticles were synthesized by an easy route without any chelating agents or surfactants, and confirmed using scanning electron microscopy, particle size distribution measurement and X‐ray diffraction. The characterization results show that the as‐fabricated CPE membranes present not only an abundant porous structure, but also an improved mechanical strength. In particular, sample CPE‐5 presents the best properties when the doped content of the monodispersed ZrO₂ nanoparticles reaches 5 wt% in the polymer matrix, in which the liquid uptake and ionic conductivity at room temperature are about 192.4% and 3.926 mS cm^?1, and the electrochemical working window and thermal decomposition temperature can increase to 5.1 V and 420 °C, respectively. Moreover, an assembled LiCoO₂/CPE‐5/Li coin cell can deliver excellent rate and cycling performance, in which the discharge specific capacity of the cell can show about 83.95% capacity retention at 2.0 C after 85 cycles. © 2018 Society of Chemical Industry