Reactive compatibilization of poly(l‐lactide)/poly(butylene succinate) blends through polyester maleation: from materials to properties

The melt blending of poly(l ‐lactide) (PLLA) with biodegradable poly(butylene succinate) (PBS) is considered with a view to fine‐tuning its mechanical properties and its degradability. For this purpose, both maleic‐anhydride‐grafted PLLA (PLLA‐g‐MA) and maleic‐anhydride‐grafted PBS (PBS‐g‐MA) were prepared and used as reactive compatibilizers. The influence of PBS melt viscosity on the morphology and mechanical properties of PLLA/PBS blends was studied. Interestingly, the blending of low viscosity PBS with PLLA allows PLLA to be toughened while the use of high viscosity PBS led to PLLA/PBS blends exhibiting co‐continuous morphology. The nanostructure of the co‐continuous blends may be tuned through the joint action of organo‐modified clays and reactive compatibilizers. The effect of PBS on PLLA degradability was also investigated. The accelerated weathering testing of blends reveals that such combination of biodegradable polymers allows their degradability rate to be tailored. It is found that the addition of 20 wt% PBS to PLLA allows the molar mass loss fraction to be doubled after 425 h of testing. © 2014 Society of Chemical Industry     

Morphology and flame‐retardancy properties of ternary high‐impact polystyrene/elastomer/polystyrene‐encapsulated magnesium hydroxide composites

The effects of elastomer type on the morphology, flammability, and mechanical properties of high‐impact polystyrene (HIPS)/polystyrene (PS)‐encapsulated magnesium hydroxide (MH) were investigated. The ternary composites were characterized by cone calorimetry, mechanical testing, and scanning electron microscopy. Morphology was controlled with poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) triblock copolymer or the corresponding maleinated poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS‐g‐MA). The HIPS/SEBS/PS‐encapsulated MH composites exhibited separation of the filler and elastomer, whereas the HIPS/SEBS‐g‐MA/PS‐encapsulated MH composites exhibited encapsulation of the filler by SEBS‐g‐MA. The flame‐retardant and mechanical properties of the ternary composites were strongly dependent on microstructure. The composites with an encapsulation structure showed higher flame‐retardant properties than those with a separation structure at the optimum use level of SEBS‐g‐MA. Furthermore, the composites with a separation structure showed a higher modulus and impact strength than those with an encapsulation structure. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Organomodification of montmorillonite and its effects on the properties of poly(butylene succinate) nanocomposites

The pristine sodium montmorillonite (MMT) was organically modified with hexadecyltrimethylammonium bromide (HTAB) at different contents. The organoclay was characterized by X‐ray diffraction (XRD), Fourier transform infrared spectroscopy, energy dispersive X‐ray techniques, and thermogravimetric analysis. Then, poly(butylene succinate) (PBS) nanocomposites were prepared by melt‐mixing process using maleic anhydride‐grafted PBS (PBS‐g‐MA) as compatibilizer. It was found that the mechanical properties of PBS nanocomposites filled with organoclay were apparently higher than that of the nanocomposite filled with MMT. This is attributed to the better filler–matrix interactions between PBS and the organoclay and the better filler dispersion. This is verifiable through the XRD, scanning electron microscopy, and transmission electron microscopy. The addition of PBS‐g‐MA further improved the mechanical properties. It was also found that our laboratory synthesized organoclay modified with HTAB has provided a better reinforcing efficiency when compared with the commercial octadecylamine‐modified organoclay. Besides that the thermal properties of PBS nanocomposites were studied through differential scanning calorimetry. POLYM. ENG. SCI., 2013. © 2013 Society of Plastics Engineers     

Synthesis and evaluation of biodegradable segmented multiblock poly(ether ester) copolymers for biomaterial applications

Based on 1,4‐succinic acid, 1,4‐butanediol, poly(ethylene glycol)s and dimethyl terephthalate, biodegradable segmented multiblock copolymers of poly[(butylene terephthalate)‐co‐poly(butylene succinate)‐block‐poly(ethylene glycol)] (PTSG) were synthesized with different poly(butylene succinate) (PBS) molar fractions and varying the poly(ethylene glycol) (PEG) segment length, and were evaluated as biomedical materials. The copolymer extracts showed no in vitro cytotoxicity. However, sterilization of the copolymers by gamma irradiation had some limited effect on the cytotoxicity and mechanical properties. A copolymer consisting of PEG‐1000 and 20 mol% PBS, assigned as 1000PBS20 after SO₂ gas plasma treatment, sustained the adhesion and growth of dog vascular smooth muscle cells. The in vivo biocompatibility of this sample was also measured subcutaneously in rats for 4 weeks. The assessments indicated that these poly(ether ester) copolymers are good candidates for anti‐adhesion barrier and drug controlled‐release applications. Copyright © 2004 Society of Chemical Industry     

Preparation and study of intumescent flame retardant poly(butylene succinate) using MgAlZnFe‐CO3 layered double hydroxide as a synergistic agent

Intumescent flame retardant consisting of ammonium polyphosphate and melamine, and MgAlZnFe‐CO₃ layered double hydroxides (LDHs) prepared by the constant pH coprecipitation method, were added to poly(butylene succinate) (PBS) via melt blending to obtain novel intumescent flame retardant poly(butylene succinate) (IFR‐PBS) composites. A study on the effect of MgAlZnFe‐CO₃ LDHs on the mechanical, thermal, and flame retardancy properties of IFR‐PBS composites was investigated. It was revealed that IFR‐PBS composites exhibited both excellent flame retardancy and antidripping properties when the content of MgAlZnFe‐CO₃ LDHs was 1% (the total loading of flame retardant was 20%), for a goal of vertical flammability (UL‐94) V‐0 rate and a limiting oxygen index value of 35. The results showed that a suitable amount of MgAlZnFe‐CO₃ LDHs had a noticeable synergistic effect on IFR‐PBS composites. Importantly, tensile strength and flexural strength were improved by the presence of MgAlZnFe‐CO₃ LDHs. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40736.     

Characterization and improved electrical conductivity of partially biodegradable polyaniline/poly(1,4‐butylene succinate) polymer composite films

Polyaniline/poly(1,4‐butylene succinate) (PANI/PBS) composites were prepared by the polymerization of aniline hydrochloride in the presence of different weight percentages of poly(1,4‐butylene succinate) biodegradable polymer by in situ deposition technique. The oxidative polymerization of aniline hydrochloride was performed by the drop wise addition of an aqueous ammonium persulfate solution. Fourier‐transform infrared spectroscopy, surface morphology, and thermogravimetric analyses indicated a strong interaction between PANI and PBS. The temperature‐dependent DC conductivity and biodegradable properties of PANI/PBS were also investigated. The results showed that both the conductivity and biodegradability of the composites was significantly increased by the addition of PBS. POLYM. COMPOS., 35:2010–2017, 2014. © 2014 Society of Plastics Engineers     

Properties of poly(butylene adipate‐co‐terephthalate) and sunflower head residue biocomposites

Utilization of low‐value agricultural waste for polymer composite materials has great environmental and economical benefits. Sunflower head residue (SHR) as an agricultural waste may be used as a reinforcement in polymeric materials because of its fiber characteristics. In this work, composites of biodegradable poly(butylene adipate‐co‐terephthalate) (PBAT) and SHR were prepared via melt‐extrusion compounding. To improve interfacial compatibility, maleic anhydride (MA) grafted PBAT (PBAT‐g‐MA) was prepared and used as a compatibilizer for the PBAT/SHR composites. The effects of the concentrations of SHR and PBAT‐g‐MA on the morphology, mechanical properties, melt rheology, and water resistance of the composites were examined. Interfacial adhesion between phases in the PBAT/SHR composites was enhanced by the introduction PBAT‐g‐MA as interface‐strengthening agent, resulting in improved mechanical properties and moisture resistance of the composite. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44644.     

Effect of isocyanate‐modified fumed silica on the properties of poly(butylene succinate) nanocomposites

Using the grafting method on a silica surface with PBS molecules, we prepared novel poly(butylene succinate) (PBS)/silica nanocomposites to enhance dispersibility and interfacial adhesion between silica particles and the PBS matrix, and also investigated the effects of silica‐g‐PBS on the PBS matrix using differential scanning calorimetry, thermogravimetric analysis, transmission electron microscopy, a tensile testing machine, and rheometry. The thermal stability, mechanical properties, and rheological properties of PBS nanocomposites containing silica‐g‐PBS was remarkably improved because of the surface characteristics of the silica grafted with PBS molecules, which provided good compatibility and dispersion. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Performance and biodegradability of a maleated polyester bioplastic/recycled sugarcane bagasse system

The biodegradability, morphology, and mechanical properties of composite materials made of poly(butylene succinate adipate) (PBSA) and sugarcane bagasse (SCB) were evaluated. Composites containing maleic anhydride (MA)‐grafted PBSA (PBSA‐g‐MA/SCB) exhibited noticeably superior mechanical properties because of greater compatibility between the two components. The dispersion of SCB in the PBSA‐g‐MA matrix was highly homogeneous as a result of ester formation between the carboxyl groups of PBSA‐g‐MA and hydroxyl groups in SCB and the consequent creation of branched and crosslinked macromolecules. Each composite was subjected to biodegradation tests in a Rhizopus oryzae compost. Morphological observations indicated severe disruption of film structure after 60 days of incubation, and both the PBSA and the PBSA‐g‐MA/SCB composite films were eventually completely degraded. The PBSA‐g‐MA/SCB films were more biodegradable than those made of PBSA and exhibited a higher intrinsic viscosity, implying a strong connection between these characteristics and biodegradability. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Crystallization behavior of partially crosslinked poly(β‐hydroxyalkonates)/poly(butylene succinate) blends

Partially crosslinked poly(β‐hydroxybutyrate‐co‐β‐hydroxyvalerate)/poly(butylene succinate) (PHBV/PBS) and poly(β‐hydroxybutyrate)/poly(butylene succinate) (PHB/PBS) blends were prepared by melt compounding with dicumyl peroxide. The effect of partial crosslinking on crystallization of the PHBV/PBS and PHB/PBS blends was investigated systematically. Differential scanning calorimetry results showed that the overall crystallization rates of both PHBV and PBS in their blends were enhanced considerably by the partial crosslinking. Similar results were also detected in the PHB/PBS blends. The polarized optical microscope observation displayed that the nuclei density of PHBV was increased while the spherulitic morphology did not change much. Conversely, the PBS spherulites turned into cloud‐like morphology after the partial crosslinking which is a result of the decrease in spherulite size, the reduction in interspherulite distance and the interconnection of fine PBS domains. Wide angle X‐ray diffraction patterns confirmed the enhancement in crystallization of the PHBV/PBS blends after the partial crosslinking without modification on crystalline forms of the PHBV and PBS components. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41020.     

A compatibilized composite of recycled polypropylene filled with cellulosic fiber from recycled corrugated paper board: Mechanical properties,morphology, and thermal behavior

This article deals with the feasibility of using recycled corrugated paper board (rPF) as the reinforcing material for recycled plastics. The composites of recycled polypropylene (rPP) and rPF were prepared by extrusion compounding and injection molding, and the rPP/rPF composites compatibilized by maleic anhydride grafted PP (PP‐g‐MA), maleic anhydride grafted ethylene‐1‐octene copolymer (POE‐g‐MA), and maleic anhydride grafted styrene‐ethylene‐butylene‐styrene copolymer (SEBS‐g‐MA) were also prepared. The crystallization and melting behavior, mechanical properties, thermal stability, and morphology of these composites were studied. The results indicated that rPF promoted the crystallization, enhanced the strength and toughness of rPP/rPF composites to some extent while decreased thermal stability at the same time. PP‐g‐MA and POE‐g‐MA improved the dispersion and interface adhesion of rPF, and further upgraded the mechanical properties and vicat softening temperatures. Among these compatibilizers, PP‐g‐MA was most favorable to the strength improvement while POE‐g‐MA was most favorable to the toughness improvement. As for SEBS‐g‐MA, it had no obvious modification effect. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Macromolecular design of novel sulfur‐containing copolyesters with promising mechanical properties

The miscibility of poly(butylene succinate) (PBS)/poly(butylene thiodiglycolate) (PBTDG) blends was investigated by DSC technique. PBS and PBTDG were completely immiscible in as blended‐state, as evidenced by the presence of two T_gs at ?34 and ?48°C, respectively. The miscibility changes upon mixing at elevated temperature: the original two phases merged into a single one because of transesterification reactions. Poly(butylene succinate/thiodiglycolate) block copolymers, prepared by reactive blending of the parent homopolymers, were studied to investigate the effects of transesterification reactions on the molecular structure and solid‐state properties. ¹³C‐NMR analysis evidenced the formation of copolymers whose degree of randomness increased with mixing time. Thermal characterization results showed that all the samples were semicrystalline, with a soft rubbery amorphous phase and a rigid crystal phase whose amount decreased by introducing BTDG units into the PBS chain (20 ≤ χ_c ≤ 41). Lastly, the mechanical properties were found strictly related to crystallinity degree (χ_c), the random copolymer, exhibiting the lowest elastic modulus (E = 61 MPa) and the highest deformation at break (ε_b (%) = 713). © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Study of the effect of processing conditions on the co‐injection of PBS/PBAT and PTT/PBT blends for parts with increased bio‐content

This work studies the effect of processing parameters on mechanical properties and material distribution of co‐injected polymer blends within a complex mold shape. A partially bio‐sourced blend of poly(butylene terephthalate) and poly(trimethylene terephthalate) PTT/PBT was used for the core, with a tough biodegradable blend of poly (butylene succinate) and poly (butylene adipate‐co‐terephthalate) PBS/PBAT for the skin. A ½ factorial design of experiments is used to identify significant processing parameters from skin and core melt temperatures, injection speed and pressure, and mold temperature. Interactions between the processing effects are considered, and the resulting statistical data produced accurate linear models indicating that the co‐injection of the two blends can be controlled. Impact strength of the normally brittle PTT/PBT blend is shown to increase significantly with co‐injection and variations in core to skin volume ratios to have a determining role in the overall impact strength. Scanning electron microscope images were taken of co‐injected tensile samples with the PBS/PBAT skin dissolved displaying variations of mechanical interlocking occurring between the two blends. © 2014 The Authors Journal of Applied Polymer Science Published by Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41278.     

Influences of compatibilizers on rheology and mechanical properties of propylene random copolymer/styrene‐ethylene‐butylene‐styrene block copolymer/organic‐montmorillonite nanocomposites

Propylene random copolymer (PPR)/styrene‐ethylene‐butylene‐styrene block copolymer (SEBS)/compatibilizer/organic‐montmorillonite (OMMT) quaternary nanocomposites and PPR/compatibilizer/OMMT ternary nanocomposites were prepared via two‐stage melt blending and influences of compatibilizers, maleic anhydride (MA) grafted styrene‐ethylene‐butylene‐styrene copolymer (SEBS‐g‐MA), poly(octene‐co‐ethylene) (POE‐g‐MA), or propylene block copolymers (PPB‐g‐MA), on rheology and mechanical properties of the nanocomposites were investigated. The results of X‐ray diffraction measurement and transmission electron microscopy observation showed that OMMT layers were mainly intercalated in the nanocomposites except for the mainly exfoliated structure in the quaternary nanocomposites using POE‐g‐MA as compatibilizer. The nanocomposites exhibited pseudo‐solid like viscoelasticity in low frequencies and shear‐thinning in high shear rates. As far as OMMT dispersion was concerned, POE‐g‐MA was superior to SEBS‐g‐MA and PPB‐g‐MA, which gives rise to the highest viscosities in both the ternary and quaternary nanocomposites. The quaternary nanocomposites containing POE‐g‐MA were endowed with balanced toughness and rigidity. It was suggested that a suitable combination of compatibilizer and SEBS was an essentially important factor for adjusting the OMMT dispersion and distribution, the rheological and mechanical performances of the nanocomposites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Mechanical properties of wollastonite‐reinforced polypropylene composites modified with SEBS and SEBS‐g‐MA elastomers

Mechanical properties of isotactic polypropylene/wollastonite/styrene rubber block copolymers (iPP/wollastonite/SRBC) composites were studied as a function of elastomeric poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) triblock copolymer (SEBS) and SEBS grafted with maleic anhydride (SEBS‐g‐MA) content from 0 to 20 vol%. Microphase morphology was stronger influenced by SRBC elastomers than by different wollastonite types. Higher encapsulation ability of SEBS‐g‐MA than SEBS caused more expressive core‐shell morphology and consequently higher notched impact strength as well as yield parameters, but lower Young's modulus. Higher ductility of the composites with SEBS than with SEBS‐g‐MA has been primarily caused by better miscibility of the polypropylene chains with SEBS molecules. Surface properties of components and adhesion parameters also indicated that adhesion at SEBS‐g‐MA/wollastonite interface, which was stronger than the one at the SEBS/wollastonite interface, influenced higher encapsulation of wollastonite particles by SEBS‐g‐MA. POLYM. ENG. SCI., 47:1873–1880, 2007. © 2007 Society of Plastics Engineers     

Development and characterization of green composites from bio‐based polyethylene and peanut shell

In the present work, different compatibilizers, namely polyethylene‐graft‐maleic anhydride (PE‐g‐MA), polypropylene‐graft‐maleic anhydride (PP‐g‐MA), and polystyrene‐block‐poly(ethylene‐ran‐butylene)‐block‐polystyrene‐graft‐maleic anhydride (SEBS‐g‐MA) were used on green composites derived from biobased polyethylene and peanut shell (PNS) flour to improve particle–polymer interaction. Composites of high‐density polyethylene/peanut shell powder (HDPE/PNS) with 10 wt % PNS flour were compatibilized with 3 wt % of the abovementioned compatibilizers. As per the results, PP‐g‐MA copolymer lead to best optimized properties as evidenced by mechanical characterization. In addition, best particle–matrix interface interactions with PP‐g‐MA were observed by scanning electron microscopy (SEM). Subsequently HDPE/PNS composites with varying PNS flour content in the 5–30 wt % range with PP‐g‐MA compatibilizer were obtained by melt extrusion and compounding followed by injection molding and were characterized by mechanical, thermal, and morphological techniques. The results showed that PNS powder, leads to an increase in mechanical resistant properties (mainly, flexural modulus, and strength) while a decrease in mechanical ductile properties, that is, elongation at break and impact absorbed energy is observed with increasing PNS flour content. Furthermore, PNS flour provides an increase in thermal stability due to the natural antioxidant properties of PNS. In particular, composites containing 30 wt % PNS powder present a flexural strength 24% and a flexural modulus 72% higher than the unfilled polyethylene and the thermo‐oxidative onset degradation temperature is increased from 232 °C up to 254 °C thus indicating a marked thermal stabilization effect. Resultant composites can show a great deal of potential as base materials for wood plastic composites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43940.     

Mechanical properties of glass bead‐ and wollastonite‐filled isotactic‐polypropylene composites modified with thermoplastic elastomers

Mechanical properties of the isotactic‐polypropylene/glass bead (iPP/GB) and iPP/wollastonite (iPP/W) composites modified with thermoplastic elastomers, the poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) copolymer (SEBS) and corresponding block copolymer grafted with maleic anhydride (SEBS‐g‐MA), were investigated. An increase in toughness of iPP with the elastomers was associated with a decrease in rigidity and strength. Mechanical performance of iPP increased more with acicular W than with spherical GB due to reinforcing effect of W. Comparing the (iPP/GB)/SEBS and (iPP/W)/SEBS composites having the separate microstructure, strength and toughness values of the iPP/GB and iPP/W composites increased more with SEBS‐g‐MA at the expense of rigidity due to the core‐shell microstructure with strong interfacial adhesion. Moreover, the iPP/W composite exhibited superior mechanical performance with 2.5 and 5 vol% of SEBS‐g‐MA because of a positive synergy between the core‐shell microstructure and reinforcing effect of acicular W. The extended models revealed that the elastomer and filler particles in the (iPP/GB)/SEBS and (iPP/W)/SEBS composites acted individually due to the separate microstructure. However, the rigid GB and W particles encapsulated with the thick elastomer interlayer (R₀/R₁ = 0.91) in the (iPP/GB)/SEBS‐g‐MA and (iPP/W)/SEBS‐g‐MA composites acted like neither big elastomer particles nor like individual rigid particles, inferring more complicated failure mechanisms in the core‐shell composites. POLYM. COMPOS., 31:1285–1308, 2010. © 2010 Society of Plastics Engineers     

Poly(butylene succinate) ionomers and their use as compatibilizers in nanocomposites

A series of low‐molecular‐weight poly(butylene succinate‐co‐glutarate‐co−2‐trimethylammonium chloride glutarate) terpolyester ionomers containing 35% mol of total glutarate units but varying in the content of charged units were synthesized by polycondensation at mild temperatures using a scandium catalyst. The terpolyester ionomers started to decompose at the temperatures of >175°C and all of them were semicrystalline and have glass transition temperature similar to poly(butylene succinate) (PBS). These terpolyesters were used to compatibilize the nanocomposites made of PBS‐cloisite (CL) prepared by melt extrusion. X‐ray diffraction revealed that an intercalated structure was present in these nanocomposites. The thermal properties of the three‐component mixtures did not differ substantially from those of PBS–CL but the mechanical properties were significantly improved by the addition of the ionomer, in particular tenacity. The beneficial effect afforded by the terpolyester ionomer was attributed to its ability for strengthening the binding between the PBS and the nanoclay. POLYM. COMPOS., 37:2603–2610, 2016. © 2015 Society of Plastics Engineers     

Rice straw fiber reinforced high density polyethylene composite: Effect of coupled compatibilizating and toughening treatment

In this study, rice‐straw (RS) filled high density polyethylene (HDPE) composites were manufactured by extrusion and injection molding. Three compatibilizers, which are unfunctionalized ethylene/propylene copolymer (uEPR), maleic anhydride grafted EPR (EPR‐g‐MA) and PE‐g‐MA, and their combinations were introduced to strengthen fiber‐matrix interphase. The mechanical and morphological properties of composites were investigated. For single‐compatibilizer system, PE‐g‐MA or EPR‐g‐MA alone enhanced tensile, flexural, and impact strengths of resultant composites compared with HDPE/RS system without compatibilizers. Different toughening origins of individual compatibilizer were discussed based on composites' interphase morphologies and mechanical properties. For combined‐compatibilizers system, the PE‐g‐MA/EPR weight ratio is important for several properties of composites. The optimum ratio was considered as 2 : 1 and 1 : 1 for PE‐g‐MA/uEPR and PE‐g‐MA/EPR‐g‐MA modified composites, respectively. Also, composites modified by combined PE‐g‐MA/EPR‐g‐MA showed better impact strength than that modified by PE‐g‐MA alone. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation and performance characteristics of short‐glass‐fiber/maleated styrene–ethylene–butylene–styrene/polypropylene hybrid composites

Eighty/twenty polypropylene (PP)/styrene–ethylene–butylene–styrene (SEBS) and 80/20 PP/maleated styrene–ethylene–butylene–styrene (SEBS‐g‐MA) blends reinforced with 30 wt % short glass fibers (SGFs) were prepared by extrusion and subsequent injection molding. The influence of the maleic anhydride (MA) functional group grafted to SEBS on the properties of SGF/SEBS/PP hybrid composites was studied. Tensile and impact tests showed that the SEBS‐g‐MA copolymer improved the yield strength and impact toughness of the hybrid composites. Extensive plastic deformation occurred at the matrix interface layer next to the fibers of the SGF/SEBS‐g‐MA/PP composites during impact testing. This was attributed to the MA functional group, which enhanced the adhesion between SEBS and SGF. Differential scanning calorimetry measurements indicated that SEBS promoted the crystallization of PP spherulites by acting as active nucleation sites. However, the MA functional group grafted to SEBS retarded the crystallization of PP. Finally, polarized optical microscopy observations confirmed the absence of transcrystallinity at the glass‐fiber surfaces of both SGF/SEBS/PP and SGF/SEBS‐g‐MA/PP hybrid composites. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1303–1311, 2002