Comparison frequency doubling and charge pump matching techniques for dual-band /spl Delta//spl Sigma/ fractional-N frequency synthesizer

The frequency synthesizer with two LC-VCOs is fully integrated in a 0.35-/spl mu/m CMOS technology. In supporting dual bands, all building blocks except VCOs are shared. A current compensation scheme using a replica charge pump improves the linearity of the frequency synthesizer and, thus, suppresses spurious tones. To reduce the quantization noise from a /spl Delta//spl Sigma/ modulator and the noise from the building blocks except the VCO, the proposed architecture uses a frequency doubler with a noise-insensitive duty-cycle correction circuit (DCC) in the reference clock path. Power consumption is 37.8 mW with a 2.7-V supply. The proposed frequency synthesizer supports 10-kHz channel spacing with the measured phase noise of -114 dBc/Hz and -141 dBc/Hz at 100-kHz and 1.25-MHz offsets, respectively, in the PCS band. The fractional spurious tone at 10-kHz offset is under -54 dBc.     

A fully integrated multiband MIMO WLAN transceiver RFIC

A multiple-input/multiple-output (MIMO) transceiver RFIC compliant with IEEE 802.11a/b/g and Japan wireless LAN (WLAN) standards is presented. The transceiver has two complete radio paths integrated on the same chip. When two chips are used in tandem to form a four-path composite beam forming (CBF) system, 15 dB of link margin improvement is obtained. The transceiver was implemented in a 47-GHz SiGe technology with 29.1-mm/sup 2/ die size. It consumes 195 mA in RX mode and 240 mA in TX mode from a 2.75-V supply.     

A 1.76-GHz 22.6-mW /spl Delta//spl Sigma/ fractional-n frequency synthesizer

A /spl Delta//spl Sigma/ fractional-N frequency synthesizer for the 2-GHz-range wireless communication applications is implemented in a 0.35-/spl mu/m BiCMOS process, using only CMOS components. The synthesizer achieves a close-in phase noise of -81 dBc/Hz, while the spurious tones are at -85 dBc. The synthesizer features a multiple-modulus prescaler employing the phase-switching architecture to minimize the power dissipation. The entire prescaler, including the gigahertz-speed first stages, is implemented using full-swing logic. The current source structure employed in the charge pump provides a constant output current over a wide, almost rail-to-rail output voltage range. The power dissipation of the synthesizer chip is 22.6 mW from a 2.7-V supply.     

11 GHz CMOS /spl Sigma//spl Delta/ frequency synthesiser

A fully integrated 11 GHz fractional-N PLL with a three-stage MASH SigmaDelta modulator with DC dither in all stages is implemented in a standard 0.13 mum CMOS technology. The synthesiser generates no fractional spurs at frequency offsets outside the loop bandwidth and a small number of fractional spurs with the power not exceeding -44 dBc within the loop bandwidth at the carrier frequency of 11 GHz     

A /spl Sigma/-/spl Delta/ fractional-N frequency synthesizer using a wide-band integrated VCO and a fast AFC technique for GSM/GPRS/WCDMA applications

A fractional-N frequency synthesizer (FNFS) in a 0.5-/spl mu/m SiGe BiCMOS technology is implemented. In order to operate in a wide-band frequency range, a switched-capacitors bank LC tank voltage-controlled oscillator (VCO) and an adaptive frequency calibration (AFC) technique are used. The measured VCO tuning range is as wide as 600 MHz (40%) from 1.15 to 1.75 GHz with a tuning sensitivity from 5.2 to 17.5 MHz/V. A 3-bit fourth-order /spl Sigma/-/spl Delta/ modulator is used to reduce out-of-band phase noise and to meet a frequency resolution of less than 3 Hz as well as agile switching time. The experimental results show -80 dBc/Hz in-band phase noise within the loop bandwidth of 25 kHz and -129 dBc/Hz out-of-band phase noise at 400-kHz offset frequency. The fractional spurious is less than -70 dBc/Hz at 300-kHz offset frequency and the reference spur is -75 dBc/Hz. The lock time is less than 150 /spl mu/s. The proposed synthesizer consumes 19.5 mA from a single 2.8-V supply voltage and meets the requirements of GSM/GPRS/WCDMA applications.     

A modeling approach for /spl Sigma/-/spl Delta/ fractional-N frequency synthesizers allowing straightforward noise analysis

A general model of phase-locked loops (PLLs) is derived which incorporates the influence of divide value variations. The proposed model allows straightforward noise and dynamic analyses of /spl Sigma/-/spl Delta/ fractional-N frequency synthesizers and other PLL applications in which the divide value is varied in time. Based on the derived model, a general parameterization is presented that further simplifies noise calculations. The framework is used to analyze the noise performance of a custom /spl Sigma/-/spl Delta/ synthesizer implemented in a 0.6 /spl mu/m CMOS process, and accurately predicts the measured phase noise to within 3 dB over the entire frequency offset range spanning 25 kHz to 10 MHz.     

Noise-coupled /spl Delta//spl Sigma/ ADC's

The first-order noise coupling scheme proposed earlier is generalised to the realisation of higher-order enhancement. It is also extended to single-stage DeltaSigma loops, and to split structures with self-enhancement. The advantages and limitations of these new DeltaSigma architectures are compared with those of conventional single-stage and cascade DeltaSigma structures. As demonstrated by an example, they exhibit improved stability and robustness under practical fabrication conditions     

A direct digital frequency synthesizer with fourth-order phase domain /spl Delta//spl Sigma/ noise shaper and 12-bit current-steering DAC

This paper presents a direct digital frequency synthesizer (DDFS) with a 16-bit accumulator, a fourth-order phase domain single-stage /spl Delta//spl Sigma/ interpolator, and a 300-MS/s 12-bit current-steering DAC based on the Q/sup 2/ Random Walk switching scheme. The /spl Delta//spl Sigma/ interpolator is used to reduce the phase truncation error and the ROM size. The implemented fourth-order single-stage /spl Delta//spl Sigma/ noise shaper reduces the effective phase bits by four and reduces the ROM size by 16 times. The DDFS prototype is fabricated in a 0.35-/spl mu/m CMOS technology with active area of 1.11mm/sup 2/ including a 12-bit DAC. The measured DDFS spurious-free dynamic range (SFDR) is greater than 78 dB using a reduced ROM with 8-bit phase, 12-bit amplitude resolution and a size of 0.09 mm/sup 2/. The total power consumption of the DDFS is 200mW with a 3.3-V power supply.     

Sturdy MASH /spl Delta//spl Sigma/ modulator

A new Delta-Sigma modulator is proposed. Its operation is similar to that of a multi-stage noise-shaping structure but requires no digital noise cancellation filters. Thus, the need for matching required between analogue and digital filters is eliminated. Simulation results and mathematical analysis demonstrate the effectiveness of this structure     

A high-frequency double-sampling second-order /spl Delta//spl Sigma/ modulator

As the minimum feature size of VLSI technologies scales down, more of the signal processing tasks are performed in the digital domain. This results in increased speed, resolution, and dynamic range requirements for the analog-to-digital converter (ADC). High-speed and high-accuracy designs can be achieved by using oversampling ADC structures, which demand amplifiers with a high gain and a high unity-gain frequency. Due to the difficulty to meet both of these specifications, the ADC resolution at a frequency in the megahertz range appears to be limited by amplifier settling requirements. Design techniques to improve the ADC performance are presented. The proposed modulator structure uses the double-sampled technique, which increases by a factor of two the maximum speed of operation and correctly operates even with low dc gain amplifiers. Furthermore, the signal-to-noise ratio is significantly improved by a calibration stage, which dynamically estimates the offset errors to be removed by a simple subtraction from the output signal.     

Nonlinearity correction for multibit /spl Delta//spl Sigma/ DACs

This paper presents a digital correction technique for wide-band multibit error-feedback (EF) digital-to-analog converters (DACs). The integral nonlinearity (INL) error of the multibit DAC is estimated (on line or off line) by a calibration analog-to-digital converter (CADC) and stored in a random-access memory table. The INL values are then used to compensate for the multibit DAC's distortion by a simple digital addition. The accuracy requirements for the error estimates are derived. These requirements can be significantly relaxed when the correction is combined with data-weighted averaging (DWA). Simulation and discrete-component measurement results are presented for a fourth-order 5-bit EF DAC. The results show a 14-bit DAC operating at an oversampling ratio of 8, which is suitable for digital subscriber line applications. The correction uses simple digital circuitry and a 3-bit CADC enhanced by DWA.     

A fourth-order /spl Sigma//spl Delta/ interface for micromachined inertial sensors

This paper presents the design and implementation of a high-order /spl Sigma//spl Delta/ interface for micromachined inertial sensors, which employs an electronic filter in series with the mechanical sensor element to reject the excessive in-band quantization noise inherently present in state-of-the-art second-order solutions. A fourth-order prototype was fabricated in a standard 0.5-/spl mu/m CMOS process. The active circuit area measures 0.9 mm/sup 2/, and the interface consumes 13 mW from a 5-V supply and achieves resolution of 1/spl deg//s//spl radic/Hz with a gyroscope and 150/spl mu/g//spl radic/Hz with an accelerometer. Comparison between the measured and simulated behavior of the system shows that the contribution of the quantization error to the total noise is negligible.     

A 700-kHz bandwidth /spl Sigma//spl Delta/ fractional synthesizer with spurs compensation and linearization techniques for WCDMA applications

A /spl Sigma//spl Delta/ fractional-N frequency synthesizer targeting WCDMA receiver specifications is presented. Through spurs compensation and linearization techniques, the PLL bandwidth is significantly extended with only a slight increase in the integrated phase noise. In a 0.18-/spl mu/m standard digital CMOS technology a fully integrated prototype with 2.1-GHz output frequency and 35 Hz resolution has an area of 3.4 mm/sup 2/ PADs included, and it consumes 28 mW. With a 3-dB closed-loop bandwidth of 700 kHz, the settling time is only 7 /spl mu/s. The integrated phase noise plus spurs is -45 dBc for the first WCDMA channel (1 kHz to 1.94 MHz) and -65 dBc for the second channel (2.5 to 6.34 MHz) with a worst case in-band (unfiltered) fractional spur of -60 dBc. Given the extremely large bandwidth, the synthesizer could be used also for TX direct modulation over a broad band. The choice of such a large bandwidth, however, still limits the spur performance. A slightly smaller bandwidth would fulfill WCDMA requirements. This has been shown in a second prototype, using the same architecture but employing an external loop filter and VCO for greater flexibility and ease of testing.     

A 4 GHz quadrature output fractional-N frequency synthesizer for an IR-UWB transceiver

This paper describes a 4 GHz fractional-N frequency synthesizer for a 3.1 to 5 GHz IR-UWB transceiver.Designed in a 0.18μm mixed-signal & RF 1P6M CMOS process, the operating range of the synthesizer is 3.74 to 4.44 GHz. By using an 18-bit third-order ∑-△ modulator, the synthesizer achieves a frequency resolution of 15 Hz when the reference frequency is 20 MHz. The measured amplitude mismatch and phase error between I and Q signals are less than 0.1 dB and 0.8° respectively. The measured phase noise is -116 dBc/Hz at 3 MHz offset for a 4 GHz output.Measured spurious tones are lower than -60 dBc. The settling time is within 80 μs. The core circuit conupSigmaes only 38.2 mW from a 1.8 V power supply.     

一种用于IR-UWB收发器的4GHz正交输出小数频率综合器

本文针对工作于3.1GHz到5GHz频段的IR-UWB收发器,设计了一种4GHz小数频率综合器。该频率综合器采用0.18μm混合&射频CMOS工艺实现,其输出频率范围为3.74GHz到4.44GHz。通过使用多比特量化的∑-△调制器,该频率综合器在参考频率为20MHz时的输出频率分辨率达到15Hz。测试结果表明,该频率综合器的正交信号输出幅度失配和相位误差分别低于0.1dB和0.8º。该频率综合器的输出相位噪声达到-116dBc/Hz@3MHz,频谱杂散低于-60dBc。在1.8V电源电压下,该频率综合器的核心电路功耗仅为38.2mW。     

A fast block-based nonlinear decoding algorithm for /spl Sigma//spl Delta/ modulators

Previous work has established that the digital output of a /spl Sigma//spl Delta/ modulator as an A/D converter contains more information about the analog input than is extracted with conventional linear filtering. Under reasonable mathematical assumptions, optimal nonlinear decoding of the digital output can achieve significantly larger signal-to-noise ratios than linear filtering. However, the hitherto proposed decoding algorithms only demonstrate conceptual feasibility and are impractical from a computational point of view. We present a new block-based decoding algorithm that, like previous work, employs projections onto convex sets. The algorithm owes its speed to a change of projection norm, an accelerated convergence scheme, and a decimation-like subsampling; it is on the order of 10/sup 4/-10/sup 5/ times faster than one previously published algorithm for typical parameter values, and about 2-10 times slower than linear decoding. The new algorithm is applicable to all currently popular /spl Sigma//spl Delta/ architectures.<>     

Continuous-time /spl Delta//spl Sigma/ modulators using distributed resonators

We derive a method for using distributed resonators in /spl Delta//spl Sigma/ modulators and demonstrate these /spl Delta//spl Sigma/ modulators have several advantages over existing /spl Delta//spl Sigma/ modulator architectures. Like continuous-time (CT) /spl Delta//spl Sigma/ modulators, the proposed /spl Delta//spl Sigma/ modulators do not require a high-precision track-and-hold, and additionally can take advantage of the high-Q of distributed resonators. Like discrete-time /spl Delta//spl Sigma/ modulators, the proposed /spl Delta//spl Sigma/ modulators are relatively insensitive to feedback loop delays and can subsample. We present simulations of several types of these /spl Delta//spl Sigma/ modulators and examine the challenges in their design.     

The tiling phenomenon in /spl Sigma//spl Delta/ modulation

The theoretical error signal analysis of a sigma-delta (/spl Sigma//spl Delta/) modulator is a difficult problem due to the presence of a nonlinear operation (the amplitude quantization) in a feedback loop. In this paper, new deterministic knowledge on the transfer function of a /spl Sigma//spl Delta/ modulator is established, thanks to some recently observed properties of its state variables. For a large class of typical /spl Sigma//spl Delta/ modulators with constant inputs, the state variables appear to remain in a tile. We show what characteristics in a /spl Sigma//spl Delta/ modulator are specifically responsible for this property and give some initial proof of it. Under a constant input, the tiling phenomenon has as fundamental consequence that the output is a fixed and memoryless modulo function of n successive integrated versions of the input. This gives the theoretical knowledge that the modulator has an equivalent feedforward circuit expression. We give some immediate theoretical consequences on error analysis including the case of time-varying inputs.     

Integrated stereo /spl Delta//spl Sigma/ class D amplifier

A 2/spl times/40 W class D amplifier chip is realized in 0.6-/spl mu/m BCDMOS technology, integrating two delta-sigma (/spl Delta//spl Sigma/) modulators and two full H-bridge switching output stages. Analog feedback from H-bridge outputs helps achieve 67-dB power supply rejection ratio, 0.001% total harmonic distortion, and 104-dB dynamic range. The modulator clock rate is 6 MHz, but dynamically adjusted quantizer hysteresis reduces output data rate to 450 kHz, helping achieve 88% power efficiency. At AM radio frequencies, the modulator output spectrum contains a single peak, but is otherwise tone-free, unlike conventional pulse-width modulation (PWM) modulators which contain energetic tones at harmonics of the PWM clock frequency.     

A time-delay jitter-insensitive continuous-time bandpass /spl Delta//spl Sigma/ modulator architecture

In this paper, we present a new continuous-time bandpass delta-sigma (/spl Delta//spl Sigma/) modulator architecture with mixer inside the feedback loop. The proposed bandpass /spl Delta//spl Sigma/ modulator is insensitive to time-delay jitter in the digital-to-analog conversion feedback pulse, unlike conventional continuous-time bandpass /spl Delta//spl Sigma/ modulators. The sampling frequency of the proposed /spl Delta//spl Sigma/ modulator can be less than the center frequency of the input narrow-band signal.