Electrochemical properties of bare and Ta-substituted Nb2O5 nanostructures

In this work, bare and Ta-substituted Nb₂O₅ nanofibers are prepared by electrospinning followed by sintering at temperatures in the 800–1100 °C range for 1 h in air. Obtained bare and Ta-substituted Nb₂O₅ polymorphs are characterized by X-ray diffraction, scanning electron microscopy, density measurement, and Brunauer, Emmett and Teller surface area. Electrochemical properties are evaluated by cyclic voltammetry and galvanostatic techniques. Cycling performance of Nb₂O₅ structures prepared at temperature 800 °C, 900 °C, and 1100 °C shows following discharge capacity at the end of 10th cycle: 123, 140, and 164 (±3) mAh g⁻¹, respectively, in the voltage range 1.2–3.0 V and at current rate of 150 mA g⁻¹ (1.5 C rate). Heat treated composite electrode based on M-Nb₂O₅ (1100 °C) in argon atmosphere at 220 °C, shows an improved discharge capacity of 192 (±3) mAh g⁻¹ at the end of 10th cycle. The discharge capacity of Ta-substituted Nb₂O₅ prepared at 900 °C and 1100 °C showed a reversible capacity of 150, 202 (±3) mAh g⁻¹, respectively, in the voltage range 1.2–3.0 V and at current rate of 150 mA g⁻¹. Anodic electrochemical properties of M-Nb₂O₅ deliver a reversible capacity of 382 (±5) mAh g⁻¹ at the end of 25th cycle and Ta-substituted Nb₂O₅ prepared at 900 °C, 1000 °C and 1100 °C shows a reversible capacity of 205, 130 and 200 (±3) mAh g⁻¹ (at 25th cycle) in the range, 0.005–2.6 V, at current rate of 100 mA g⁻¹.     

Electrochemical characteristics of LiNi0.5Mn1.5O4 prepared by spray drying and post-annealing

LiNi_0.5Mn_1.5O₄ was prepared by a spray drying and post-annealing process. The re-annealing treatment in O₂ could not only decrease the Mn³⁺ content, but also increased the reversible capacity and significantly improve the rate capability compared to the untreated material. Moreover, the cyclic performance of the LiNi_0.5Mn_1.5O₄ depends on both the cycling rate and operating temperature, which was ascribed to the difference between the phase transition rates between cubic I ↔ cubic II and cubic II ↔ cubic III.     

Synthesis of compounds, Li(MMn11/6)O4 (M = Mn1/6, Co1/6, (Co1/12Cr1/12), (Co1/12Al1/12), (Cr1/12Al1/12)) by polymer precursor method and its electrochemical performance for lithium-ion batteries

The compounds, Li(MMn_11/6)O₄ (M = Mn_1/6, Co_1/6, (Co_1/12Cr_1/12), (Co_1/12Al_1/12), (Cr_1/12Al_1/12)) are synthesised by the polymer precursor method. The structure and the morphology of the compounds are studied by the Rietveld refined X-ray diffraction (XRD), and transmission electron microscopy (TEM) techniques, respectively. Density and the Brunauer, Emmet and Teller surface area (BET) of the compounds are also studied. The cobalt doped compound, Li(Co_1/6Mn_11/6)O₄ is found to be nanosized particles in the range of 60-100 nm, when compared to the other compounds in our present study. The oxidation state and the local structure of the compounds are analysed by the X-ray absorption spectroscopy (XAS) technique. Cyclic voltammetry (CV) and the galvanostatic charge-discharge cycling (30 mA g⁻¹) studies are made in the voltage range of 3.5-4.3 V at room temperature for all the compounds under study. The bare and (Co_1/6), and (Co_1/12Cr_1/12) substituted spinels are cycled at high current rates of 1, 2 and 5C (assuming 1C∼120 mA g⁻¹). Cycling results of Co-substituted spinels show better and long-term capacity retention at all the current rates. At the end of the second cycle, Li(Co_1/6Mn_11/6)O₄ compound delivers a discharge capacity value of 100 (±3) and 87 (±3) mAh g⁻¹ for the current rate of 2 and 5C, respectively. An excellent capacity retention value of 94% is observed at the end of the 1000 cycles for both 2 and 5C rates.     

Investigation on capacity fading of LiFePO4 in aqueous electrolyte

The capacity loss rate of LiFePO₄ in aqueous electrolyte was found to be much faster than it in organic electrolyte. The cycling stability in aqueous electrolyte with various dissolved oxygen content and pH value was extensively studied by cyclic voltammetry. It was found that both high OH⁻ and dissolve O₂ content can accelerate the cycling fading of LiFePO₄. It has been proved that the capacity fading of LiFePO₄ is due to not only chemical instability but also electrochemical instability. Mössbauer spectroscopy demonstrated that the Fe(III)-containing species was formed in the active materials arisen from the irreversible side reaction. The carbon-coated LiFePO₄ prepared by chemical vapor decomposition method shows significantly improvement in cycling stability. The carbon coating technology provides an effective approach to enhance cycling performance in aqueous electrolyte as well as proof of proposed fading mechanism.     

Crystal structure studies of thermally aged LiCoO2 and LiMn2O4 cathodes

LiCoO₂ and LiMn₂O₄ cathodes were studied by X-ray diffractometry (XRD) and electron diffraction after ageing in the charged state at elevated temperature. Some cathodes were stopped at different times during ageing and XRD measurements were taken to monitor changes in the crystal structure over ageing time. The results indicate that Li-ions intercalate into the cathodes lattice during ageing thus decreasing the available discharge capacity. Analysis of electron diffraction patterns of LiCoO₂ and LiMn₂O₄ retrieved from the cathodes after ageing shows that irreversible crystallographic transformations have taken place in both electrodes. Dark field imaging illustrates that LiCoO₂ forms a layer of spinel phase on its surface. In LiMn₂O₄ a tetragonal distorted spinel is observed when the cathode has been in the 3 V regime for considerable length of time.     

Electrochemical properties of SnO2/carbon composite materials as anode material for lithium-ion batteries

SnO₂/carbon composite anode materials were synthesized from SnCl₄·5H₂O and sucrose via a hydrothermal route and a post heat-treatment. The synthesized spherical SnO₂/carbon powders show a cauliflower-like micro-sized structure. High annealing temperature results in partial reduction of SnO₂. Metallic Sn starts to emerge at 500 °C. High Sn content in SnO₂/carbon composite is favorable for the increase of initial coulombic efficiency but not for the cycling stability. The SnO₂/carbon annealed at 500 °C exhibits high specific capacity (∼400 mAh g⁻¹), stable cycling performance and good rate capability. The generation of Li₂O in the first lithiation process can prevent the aggregation of active Sn, while the carbon component can buffer the big volume change caused by lithiation/delithiation of active Sn. Both of them make contribution to the better cycle stability.     

Electrochemical properties of carbon-mixed LiFePO4 cathode material synthesized by the ceramic granulation method

LiFePO₄/carbon composite cathode material was prepared using polyvinyl alcohol (PVA) as carbon source by pelleting and subsequent pyrolysis in N₂. The samples were characterized by XRD, SEM and TGA. Their electrochemical performance was investigated in terms of charge–discharge cycling behavior. It consists of a single LiFePO₄ phase and amorphous carbon. The special micro-morphology via the process is favorable for electrochemical properties. The discharge capacity of the LiFePO₄/C composite was 145 mAh/g, closer to the theoretical specific capacity of 170 mAh/g at 0.1 C low current density. At 3 C modest current density, the specific capacity was about 80 mAh/g, which can satisfy for transportation applications if having a more planar discharge flat.     

Enhanced electrochemical performances of LiNi0.5Mn1.5O4 spinel via ethylene glycol-assisted synthesis

A simple and effective method, ethylene glycol-assisted co-precipitation method, has been employed to synthesize LiNi_0.5Mn_1.5O₄ spinel. As a chelating agent, ethylene glycol can realize the homogenous distributions of metal ions at the atomic scale and prevent the growth of LiNi_0.5Mn_1.5O₄ particles. XRD reveals that the prepared material is a pure-phase cubic spinel structure (Fd3m) without any impurities. SEM images show that it has an agglomerate structure with the primary particle size of less than 100 nm. Electrochemical tests demonstrate that the as-prepared LiNi_0.5Mn_1.5O₄ possesses high capacity and excellent rate capability. At 0.1 C rate, it shows a discharge capacity of 137 mAh g⁻¹ which is about 93.4% of the theoretical capacity (146.7 mAh g⁻¹). At the high rate of 5 C, it can still deliver a discharge capacity of 117 mAh g⁻¹ with excellent capacity retention rate of more than 95% after 50 cycles. These results show that the as-prepared LiNi_0.5Mn_1.5O₄ is a promising cathode material for high power Li-ion batteries.     

Electrochemical properties of carbon-coated LiFePO4 cathode using graphite, carbon black, and acetylene black

Electrochemical properties of LiFePO₄ were investigated by incorporating conductive carbon from three different carbon sources (graphite, carbon black, acetylene black). SEM observations revealed that the carbon-coated LiFePO₄ were smaller than the bare LiFePO₄ particles. The carbon-coated LiFePO₄ showed much better performance in terms of the discharge capacity and cycling stability than the bare LiFePO₄. Among carbon-coated LiFePO₄, the particles coated with graphite exhibited better electrochemical properties than others coated with carbon black or acetylene black.     

Li-storage and cyclability of urea combustion derived ZnFe2O4 as anode for Li-ion batteries

The cubic ZnFe₂O₄ with the spinel structure is prepared by the urea combustion method. Powder X-ray diffraction and HR-TEM studies confirm the single-phase nature with particle size in the range, 100-300 nm. A stable and reversible capacity, 615(±10) mAh g⁻¹ (5.5 moles of Li per mole of ZnFe₂O₄) when cycled in the range, 0.005-3.0 V vs. Li at a current of 60 mA g⁻¹(0.1C) has been achieved between 15 and 50 cycles. The underlying reaction mechanism contributing to the observed capacity is the combination of ‘de-alloying-alloying’ and ‘conversion’ reactions of ‘LiZn-Fe-Li₂O composite’. Ex situ HR-TEM and SAED data on the charged-electrode confirmed the proposed reaction mechanism.     

Electrochemical properties of nanostructured Li1.2V3O8 in aqueous LiNO3 solution

The amorphous hydrated precursor of Li_1.2V₃O₈ was synthesized by soft chemistry method, and then heat-treated in air at several temperatures within the range 200–400 °C. The heat-treatment changed its morphological, structural and charging/discharging performance. The product obtained upon the treatment at 300 °C, consisting of uniform, rod-shaped particles, 100–150 nm in diameter and 300–800 nm in length, displayed the best electrochemical performance in aqueous LiNO₃ solution. Its initial discharge capacity amounted to 136.8 mAh g⁻¹ at a rate of C/5, which upon 50 charging/discharging cycles decreased for only 12%.     

Electrochemical properties of LiNiO2 cathode after TiO2 or ZnO addition

LiNiO₂ was prepared by solid state reaction, and LiNiO₂ was mixed with 1-, 2-, or 5 wt% TiO₂ or ZnO for the preparation of cathodes for a lithium ion battery. The electrochemical properties of the cathodes were investigated and the effects of the addition of TiO₂ or ZnO were discussed. The voltage vs. capacity curves for charge and discharge at different numbers of cycles for LiNiO₂, 2 wt% TiO₂-added LiNiO₂, and 2 wt% ZnO₂-added LiNiO₂ showed that in all the samples the first discharge capacity is much smaller than the first charge capacity. The addition of TiO₂ or ZnO decreased the discharge capacities, but improved the cycling performance. The discharge capacities of LiNiO₂ and 2 wt% TiO₂-added LiNiO₂ decreased as the number of cycles increased. However, the discharge capacity of 2 wt% ZnO-added LiNiO₂ increased overall as the number of cycles increased. The −dx/|dV| vs. voltage curves for the 1st and 2nd cycles of 0, 1-, 2-, or 5 wt% TiO₂ or ZnO-added LiNiO₂ showed that all the samples underwent four phase transitions during charging and discharging.     

Effect of Ti3AlC2 precursor on the electrochemical properties of the resulting MXene Ti3C2 for Li-ion batteries

The presented work compared the etching behavior between combustion synthesized Ti₃AlC₂ (SHS-Ti₃AlC₂) and pressureless synthesized Ti₃AlC₂ (PLS-Ti₃AlC₂). Because the former had a more compact structure, it was harder to be etched than PLS-Ti₃AlC₂ under the same conditions. When served as anode material for Li-ion batteries, SHS-Ti₃C₂ showed much lower capacity than PLS-Ti₃C₂ at 1?C (52.7 and 87.4?mAh?g^?1, respectively) due to the smaller d-spacing. Furthermore, Potentiostatic Intermittent Titration Technique (PITT) was used to determine the Li-ion chemical diffusion coefficient (${\mathrm{D}}_{{\mathrm{Li}}^{+}}$) of Ti₃C₂ in the range of 10^?10 ??10^?9 cm² s^?1, indicating that Ti₃C₂ could exhibit an excellent diffusion mobility for Li-ion.     

Synthesis of SnO2/Mg2SnO4 nanoparticles and their electrochemical performance for use in Li-ion battery electrodes

Uniform crystalline MgSn(OH)₆ nanocubes were synthesized by a hydrothermal method. The influences of reaction conditions were investigated and the results showed that the solvent constituents significantly affected the shape and size of MgSn(OH)₆·SnO₂/Mg₂SnO₄ has been obtained by thermal treatment at 850 °C for 8 h under a nitrogen atmosphere using MgSn(OH)₆ as the precursor. The electrochemical tests of SnO₂/Mg₂SnO₄ revealed that SnO₂/Mg₂SnO₄ has a higher capacity and better cyclability compared to pure SnO₂ or Mg₂SnO₄. The electrochemical performance of SnO₂/Mg₂SnO₄ was sensitive to the size of the nanoparticles. The lithium-driven structural and morphological changes of the electrode after cycling were also studied by the ex-situ XRD pattern and TEM tests. This work indicates that SnO₂/Mg₂SnO₄ is a promising anode material candidate for application in Li-ion batteries.     

X-ray photoelectron spectroscopy and electrochemical behaviour of 4 V cathode, Li(Ni1/2Mn1/2)O2

Layered Li(Ni_1/2Mn_1/2)O₂ was prepared by the solution and mixed hydroxide methods, characterised by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) and studied by cyclic voltammetry (CV) and charge discharge cycling in CC and CCCV modes at room temperature (r.t.) and at 50 °C. The XPS studies show about 8% of Ni³⁺ and Mn³⁺ ions are present in Li(Ni²⁺_1/2Mn_1/2⁴⁺)O₂ due to valency-degeneracy. The compound prepared at 950 °C, 12 h, solution method gives a second cycle discharge capacity of 150 mA h g⁻¹ (2.5-4.4 V) at a specific current of 30 mA g⁻¹ and retains 137 mA h g⁻¹ at the end of 40 cycles. CV shows that the redox process at 3.7-4.0 V corresponds to Ni²⁺↔Ni⁴⁺ and clear indication of Mn^3+/4+ couple was noted at 4.2-4.5 V. The observed capacity-fading (2.5-4.4 V) is shown to be contributed by the polarisation at the end of charging. The cathodic capacity is stable up to 40 cycles in the voltage window, 2.5-4.2 V both at room temperature and 50 °C.     

Electrochemical characterization of amorphous LiFe(WO4)2 thin films as positive electrodes for rechargeable lithium batteries

Amorphous LiFe(WO₄)₂ thin films have been fabricated by radio-frequency (R.F.) sputtering deposition at room temperature. The as-deposited and electrochemically cycled thin films are, respectively, characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, selected area electron diffraction, and X-ray photoelectron spectra techniques. An initial discharge capacity of 198 mAh/g in Li/LiFe(WO₄)₂ cells is obtained, and the electrochemical behavior is mostly preserved in the following cycling. These results identified the electrochemical reactivity of two redox couples, Fe³⁺/Fe²⁺ and W⁶⁺/W^x+ (x = 4 or 5). The kinetic parameters and chemical diffusion coefficients of Li intercalation/deintercalation are estimated by cyclic voltammetry and alternate-current (AC) impedance measurements. All-solid-state thin film lithium batteries with Li/LiPON/LiFe(WO₄)₂ layers are fabricated and show high capacity of 104 μAh/cm² μm in the first discharge. As-deposited LiFe(WO₄)₂ thin film is expected to be a promising positive electrode material for future rechargeable thin film batteries due to its large volumetric rate capacity, low-temperature fabrication and good electrode/electrolyte interface.     

Electrochemical performance of CoSb3/MWNTs nanocomposite prepared by in situ solvothermal synthesis

In situ solvothermally synthesized composite (SSC) and mechanically blended composite (MBC) of nanosized CoSb₃ and multiwalled carbon nanotubes (MWNTs) were prepared and investigated as potential anode materials for Li-ion batteries. It was found that SSC exhibits an entanglement structure of nanosized CoSb₃ and MWNTs and shows significantly better cycling stability than MBC. The reversible capacity of SSC electrode reaches 312 mA h g⁻¹ at the first cycle and remains above 265 mA h g⁻¹ after 30 cycles.     

FTIR spectroscopy of a LiMnPO4 composite cathode

A Li_xMnPO₄ (x = 1.0–0.15) composite cathode was investigated by Fourier-transform infrared spectroscopy at different states of charge. Significant spectral changes of the PO₄³⁻ vibrations, which are correlated with the Jahn–Teller distortion of Mn³⁺ in MnPO₄ and the 3rd ionization potential of Mn, were observed upon electrochemical delithiation of LiMnPO₄. The presence of two sets of peaks observed in the series of delithiated Li_xMnPO₄ spectra is consistent with a two-phase process for delithiation. These results provide insight into the structural changes that occur during lithium extraction and insertion in LiMnPO₄.     

Synthesis and electrochemical performance of LiNi0.5Mn1.5O4 spinel compound

Spinel compound LiNi_0.5Mn_1.5O₄ was synthesized by a chemical wet method. Mn(NO₃)₂, Ni(NO₃)₂·6H₂O, NH₄HCO₃ and LiOH·H₂O were used as the starting materials. At first, Mn(NO₃)₂ and Ni(NO₃)₂·6H₂O reacted with NH₄HCO₃ to produce a precursor, then the precursor reacted with LiOH·H₂O to synthesize product LiNi_0.5Mn_1.5O₄. The product showed a single spinel phase under appropriate calcination conditions, and exhibited a high voltage plateau at about 4.6-4.8 V in the charge/discharge process. The LiNi_0.5Mn_1.5O₄ had a discharge specific capacity of 118 mAh/g at about 4.6 V and 126 mAh/g in total in the first cycle at a discharge current density of 2 mA/cm². After 50 cycles, the total discharge capacity was above 118 mAh/g.     

Electrochemical performance of single crystalline spinel LiMn2O4 nanowires in an aqueous LiNO3 solution

Single crystalline cubic spinel LiMn₂O₄ nanowires were synthesized by hydrothermal method and the precursor calcinations. The phase structures and morphologies were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and high-resolution transmission electron microscopy (HRTEM). Galvanostatic charging/discharging cycles of as-prepared LiMn₂O₄ nanowires were performed in an aqueous LiNO₃ solution. The initial discharge capacity of LiMn₂O₄ nanowires was 110 mAh g⁻¹, and the discharge capacity was still above 100 mAh g⁻¹ after 56 cycles at 10C-rate, and then 72 mAh g⁻¹ was registered after 130 cycles. This is the first report of a successful use of single crystalline spinel LiMn₂O₄ nanowire as cathode material for the aqueous rechargeable lithium battery (ARLB).