Cobalt(II) porphyrin complex immobilized on the binary oxide SiO2/Sb2O3: electrochemical properties and dissolved oxygen reduction study

In this work, SiO₂/Sb₂O₃ prepared by the sol-gel processing method, having a specific surface area, S_BET, of 790 m² g⁻¹, an average pore diameter of 1.9 nm and 4.7 wt.% of Sb, was used as substrate base for immobilization of the 5,10,15,20-tetrakis(1-methyl-4-pyridyl)-21H,23H-porphine ion. Cobalt(II) ion was inserted into the porphyrin ring with a yield of complex bonded to the substrate surface of 59.4 μ mol g⁻¹. A carbon paste electrode of this material was used to study, by linear sweeping voltammetric and chronoamperometric techniques, the electrocatalytic reduction of dissolved oxygen. The reduction, at the electrode solid-solution interface, occurred at −0.25 V versus SCE in 1.0 mol l⁻¹ KCl solution, pH 5.5, by a four electron mechanism. The electrode response was invariant under various oxidation-reduction cycles showing that the system is chemically very stable. Such characteristics allowed the study of the electrode response towards various dissolved oxygen concentrations using the chronoamperometry technique. The cathodic peak current intensities plotted against O₂ concentrations, between 1.0 and 12.8 mg l⁻¹, showed a linear correlation. The electrode response time was very fast, i.e. about 1 s. This study was extended using the electrode to determine the concentration of dissolved oxygen in sea water samples.     

Structural colors from TiO2/SiO2 multilayer flakes prepared by sol-gel process

Preparation of TiO₂/SiO₂ multilayer flakes and their application to decorative powders were investigated. In contrast to conventional products prepared through the multicoating of core platelets, the coreless TiO₂/SiO₂ multilayer flakes were prepared by detaching multilayer films from their substrates. These flakes exhibited structural colors, when the optical path length of both the TiO₂ and SiO₂ layers are adjusted to be one fourth of the wavelength of visible light. A multicoating of more than five layers resulted in the propagation of cracks, which prevented the preparation of thick flakes. Paint films fabricated using the multilayer flakes and acrylic resins showed reflectance spectra that were comparable with those obtained for multicoatings on substrates.     

Electrocatalytic activity of IrO2-RuO2 supported on Sb-doped SnO2 nanoparticles

Electrocatalytic IrO₂-RuO₂ supported on Sb-doped SnO₂ (ATO) nanoparticles is very active towards the oxygen evolution reaction. The IrO₂-RuO₂ material is XRD amorphous and exists as clusters on the surface of the ATO. Systematic changes to the surface chemical composition of the ATO as a function of the IrO₂:RuO₂ ratio suggests an interaction between the IrO₂-RuO₂ and ATO. Cyclic voltammetry indicates that the electrochemically active surface area of IrO₂-RuO₂ clusters is maximised when the composition is 75 mol% IrO₂-25 mol% RuO₂. Decreasing the loading of IrO₂-RuO₂ on ATO reduces the electrochemically active surface area, although there is evidence to support a decrease in the clusters size with decreased loading. Tafel slope analysis shows that if the clusters are too small, the kinetics of the oxygen evolution reaction are reduced. Overall, clusters of IrO₂-RuO₂ on ATO have similar or better performance for the oxygen evolution reaction than many previously reported materials, despite the low quantity of noble metals used in the electrocatalysts. This suggests that these oxides may be of economic advantage if used as PEM water electrolysis anodes.     

Cement composition and sulfate attack: Part I

Four cements were used to address the effect of tricalcium silicate content of cement on external sulfate attack in sodium sulfate solution. The selected cements had similar fineness and Bogue-calculated tricalcium aluminate content but variable tricalcium silicates. Durability was assessed using linear expansion and compressive strength. Phases associated with deterioration were examined using scanning electron microscopy and X-ray diffraction. Mineralogical phase content of the as-received cements was studied by X-ray diffraction using two methods: internal standard and Rietveld analysis.The results indicate that phase content of cements determined by X-ray mineralogical analysis correlates better with the mortar performance in sulfate environment than Bogue content. Additionally, it was found that in cements containing triclacium aluminate only in the cubic form, the observed deterioration is affected by tricalcium silicate content. Morphological similarities between hydration products of high tricalcium aluminate and high tricalcium silicate cements exposed to sodium sulfate environment were also observed.     

Synthesis of modified SiO2 networks: Polydimethylsiloxane-SiO2 organic-inorganic hybrids via sol-gel chemistry

Poly(dimethylsiloxane)-SiO₂ organic-inorganic hybrid networks were synthesized by a two-step, catalyst-free sol-gel process. Reactive PSX (polydimethylsiloxane) oligomers with methoxysilyl end-groups were used as the organic component, and tetramethylorthosilicate (TMOS) as the inorganic component of the hybrid. Our studies show that uncatalyzed sol-gel reactions based on TMOS can reach gelation in 7.5 h when reacted at room temperature, with a stoichiometric amount of water necessary for complete hydrolysis in the initial stages, and at a high concentration of reacting species. The relatively neutral reaction environment of this catalyst-free process is important in the synthesis of PSX-SiO₂ hybrid networks because it prevents redistribution reactions of PSX modifiers, especially when higher temperatures are used for the drying of the gels. The PSX-SiO₂ hybrid networks have reduced polarity, increased water resistance, and improved toughness compared to inorganic SiO₂ networks produced under similar conditions.     

Properties of sol-gel SnO2/TiO2 electrodes and their photoelectrocatalytic activities under UV and visible light illumination

A visible light active binary SnO₂-TiO₂ composite was successfully prepared by a sol-gel method and deposited on Ti sheet as a photoanode to degrade orange II dye. Titanium and SnO₂ can promote the development of rutile phase of TiO₂ and inhibit the formation of anatase phase of TiO₂. Formation of SnO₂ crystalline is insignificant even when the calcination temperature increases to 700 °C. Heterogenized interface between SnO₂ and TiO₂ inhibits growth of TiO₂ linkage and leads to the particle-filled surface morphology of SnO₂-containing films. The carbonaceous, Ti-O-C bonds and Ti³⁺ species are likely to account for the photoabsorption and photoelectrocatalytic (PEC) activity under visible light illumination. The electrode with 30% SnO₂ exhibits higher photocurrent when compared with those in the region of 0-50%. The 600 °C-calcined SnO₂-TiO₂ electrode indicates higher activity when compared with those at 400, 500, 700 and 800 °C. PEC degradation of orange II follows the Langmuir-Hinshelwood model and takes place much effectively in a solution of pH 3.0 than those in pH 7.0 and pH 11.0.     

The effect of foreign ions on the reactivity of the CaO-SiO2-Al2O3-Fe2O3 system: Part II: Cations

The subject of this paper is the effect of foreign cations on the reactivity of the CaO-SiO₂-Al₂O₃-Fe₂O₃ system. One reference mixture and eighteen modified mixtures, prepared by mixing the reference sample with 1% w/w of chemical grade MnO₂, CuO, V₂O₅, PbO, CdO, ZrO₂, Li₂O, MoO₃, Co₂O₃, NiO, WO₃, ZnO, Nb₂O₅, CrO₃, Ta₂O₅, TiO₂, BaO₂ and H₃BO₃ were studied. The effect on the reactivity is evaluated on the basis of the free lime content in samples sintered at 1200 and 1450 °C. At 1200 °C, the reactivity of the mixture is greatly increased in the presence of Cu and Li oxides. Based on their effect at 1450 °C, the added elements can be divided into three groups. W, Ta, Cu, Ti and Mo show the most positive effect, decreasing the free CaO (fCaO) content by 30-60%, compared with the pure sample. Cr and B cause an increase of fCaO content, while the rest of the elements exhibit a marginal positive effect. According to their volatility at 1450 °C, the added compounds can be subdivided into three groups of low (Ti⁴⁺, Cu²⁺, Mo⁶⁺, W⁺⁶, V⁵⁺, Zn²⁺, Zr⁴⁺), moderate (Cr⁶⁺, Co³⁺, Ni²⁺, Mn⁴⁺) and high volatility (Cd²⁺, Pb²⁺). All burned samples, analyzed by means of X-ray diffraction, have a final mineralogical composition, which corresponds to the structure of a typical clinker.     

Al2O3-coated SnO2/TiO2 composite electrode for the dye-sensitized solar cell

A novel Al₂O₃-coated SnO₂/TiO₂ composite electrode has been applied to the dye-sensitized solar cell. In such an electrode, two kinds of energy barriers (SnO₂/TiO₂ and TiO₂/Al₂O₃) were designed to suppress the recombination processes of the photo-generated electrons and holes. After the SnO₂ was modified by colloid TiO₂, the photoelectric conversion efficiency of the SnO₂/TiO₂ composite cell increased to 2.08% by a factor of 2.8 comparing with that of the SnO₂ cell. The Al₂O₃ layer on the SnO₂/TiO₂ composite electrode further suppressed the generation of the dark current, resulting in 37% improvement in device performance comparing with the SnO₂/TiO₂ cell.     

Electrical properties of nanoporous F doped SiO2 low-k thin films prepared by sol-gel method with catalyst HF

Using hydrofluoric acid as acid catalyst, F doped nanoporous low-k SiO₂ thin films were prepared through sol-gel method. Compared with the hydrochloric acid catalyzed film, the films showed better micro structural and electrical properties. The capacitance-voltage and current-voltage characteristics of F doped SiO₂ thin films were then studied based on the structures of metal-SiO₂-semiconductor and metal-SiO₂-metal, respectively. The density of state (DOS) of samples deposited on metal is found to decrease to a level of 2 × 10¹⁷ eV⁻¹ cm⁻³. The values of mobile ions, fix positive charges, trapped charges and the interface state density between the SiO₂/Si interfaces also decrease obviously, together with the reduction of the leakage current density and the dielectric constant, which imply the improvement of the electrical properties of thin films. After annealing at a temperature of 450^∘C, the lower values of the leakage current density and dielectric constant could be obtained, i.e. 1.06 × 10⁻⁹ A/cm² and 1.5, respectively.     

Fabrication and its characteristics of metal-loaded TiO2/SnO2 thick-film gas sensor for detecting dichloromethane

This study investigated sensitivity of the gas sensor to chemical warfare agents with the various operating temperatures and catalysts. The nano-sized SnO₂ powder mixed with metal oxide (TiO₂) was doped with transition metals (Pt, Pd and In). Thick film of nano-sized SnO₂ powder and TiO₂ was prepared by screen-printing method onto Al₂O₃ substrates with platinum electrode and chemical precipitation method. The physical and chemical properties of sensor material were investigated by SEM/EDS, XRD and BET analyzers. The measured sensitivity to simulant chemical toxic gas is defined as the percentage of resistance of value equation, (R_a − R_g/R_a), that of the resistance (R_air) of SnO₂ film in air and the resistance (R_gas) of SnO₂ film in dichloromethane. The best sensitivity and selectivity of these thick-film sensor were shown with 1 wt.% Pt and 5 wt.% TiO₂ for dichloromethane toxic gas at the operating temperature of 250 °C.     

Bifunctional redox flow battery: 2. V(III)/V(II)-l-cystine(O2) system

A new bifunctional redox flow battery (BRFB) system, V(III)/V(II)—l-cystine(O₂), was systematically investigated by using different separators. It is shown that during charge, water transfer is significantly restricted with increasing the concentration of HBr when the Nafion 115 cation exchange membrane is employed. The same result can be obtained when the gas diffusion layer (GDL) hot-pressed separator is used. The organic electro-synthesis is directly correlated with the crossover of vanadium. When employing the anion exchange membrane, the electro-synthesis efficiency is over 96% due to a minimal crossover of vanadium. When the GDL hot-pressed separator is applied, the crossover of vanadium and water transfer are noticeably prevented and the electro-synthesis efficiency of over 99% is obtained. Those impurities such as vanadium ions and bromine can be eliminated through the purification of organic electro-synthesized products. The purified product is identified to be l-cysteic acid by IR spectrum. The BRFB shows a favorable discharge performance at a current density of 20 mA cm⁻². Best discharge performance is achieved by using the GDL hot-pressed separator. The coulombic efficiency of 87% and energy efficiency of about 58% can be obtained. The cause of major energy losses is mainly associated with the cross-contamination of anodic and cathodic active electrolytes.     

Autogenous deformations of cement pastes: Part II. W/C effects, micro-macro correlations, and threshold values

A broad experimental study has been performed, from the end of mixing up to 2 years, on a set of plain cement pastes prepared with the same type I ordinary portland cement (OPC) and various water-to-cement ratios (W/C), and cured at various constant temperatures. Several parameters have been measured on the hydrating materials, such as chemical shrinkage, volumetric and one-dimensional autogenous deformations, degree of hydration of the cement, Ca(OH)₂ content and Vicat setting times. Drying shrinkage has also been measured on the mature materials. In this part II of the paper, the effects of W/C within the range 0.25-0.60 have in particular been analysed in relation to the microstructural characteristics of the materials. This micro-macro analysis has highlighted a W/C threshold value (located around 0.40) both at the macro-level (on autogenous, but also on drying deformations and durability-related properties) and at the micro-level (characteristics of the hydration products, MIP porosity and pore size distribution, etc.).In addition, volumetric and one-dimensional autogenous shrinkage deformations have been compared in the case of W/C=0.25 and T=20 °C. Finally, a critical twofold (chemical and structural) effect of calcium hydroxide has been found. When significant structural effects, generated by the formation and the growth of large-size Ca(OH)₂ crystals, take place, swelling can become prominent, as observed for one-dimensional autogenous deformations in the case of medium and high W/C, and deviations are recorded on linear relationships.     

RuO2·xH2O/NiO composites as electrodes for electrochemical capacitors: Effect of the RuO2 content and the thermal treatment on the specific capacitance

RuO₂·xH₂O/NiO composites having RuO₂ contents in the range 0-100 wt.% have been prepared by a co-precipitation method. Structural, microstructural and textural transformations after heating the as-prepared composites at 200 and 600 °C have been followed by X-ray diffraction, scanning electron microscopy (SEM) and nitrogen adsorption/desorption isotherms. At 200 °C the composites are made of micrometric particles in which nanometric crystallites of the two oxides are aggregated. The composites show microporosity (0.02-0.10 cm³/g), mesoporosity (0.07-0.12 cm³/g) and relatively high specific surface area (62-309 m²/g). At 600 °C the composites are fully dehydrated and RuO₂ has crystallized and segregated. Microporosity and mesoporosity as well as specific surface area are strongly decreased. Specific capacitance and specific surface area of the composites heated at 200 and 600 °C have been measured and discussed on the basis of the RuO₂ content. For comparison the specific capacitance and specific surface area of mixtures of NiO and RuO₂·xH₂O (or RuO₂) have been taken as references. The higher specific capacitance of the 200 °C-heated composites compared to the 600 °C-heated ones is due to the higher specific surface area of the former and the higher pseudocapacitance of RuO₂·xH₂O compared to RuO₂. The discussion reported in this work can be applied to other composites such as RuO₂·xH₂O/carbon and RuO₂·xH₂O/other oxides.     

Oxidation of CH4 over Pd supported on TiO2-doped SiO2: Effect of Ti(IV) loading and influence of SO2

Titania-modified silicas with different weight% of TiO₂ were prepared by sol–gel method and used as supports for Pd (1 wt%) catalysts. The obtained materials were tested in the oxidation of methane under lean conditions in absence and in presence of SO₂. Test reactions were consecutively performed in order to evaluate the thermal stability and poisoning reversibility. Increasing amounts of TiO₂ improved the catalytic activity, with an optimum of the performance for 10 wt% TiO₂ loading. Moreover, the titania-containing catalysts exhibited a superior tolerance towards SO₂ by either adding it to the reactants or feeding it as a pure pretreatment atmosphere at 350 °C. Catalysts were characterized by XPS, XRD, FT-IR and BET measurements. According to the structural and surface analyses, the mixed oxides contained Si–O–Ti linkages which were interpreted as being responsible for the enhanced intrinsic activity of supported PdO with respect to PdO on either pure SiO₂ or pure TiO₂. Moreover, the preferential interaction of the sulfur molecule with TiO₂ and the easy SO_x desorption from high surface area silica were the determining factors for the superior SO₂ tolerance of the TiO₂-doped catalysts.     

Gasoline-range hydrocarbon synthesis over Co/SiO2/HZSM-5 catalyst with CO2-containing syngas

Selective synthesis of gasoline-range hydrocarbons (C₅-C₁₂) was investigated in a fixed-bed micro reactor using two series of CO₂-containing syngas with various mole CO₂/(CO + CO₂) and H₂/(CO + CO₂) ratios, where Fischer-Tropsch synthesis(FTS) and in situ hydrocracking/hydroisomerization were performed over bifunctional Co/SiO₂/HZSM-5 catalyst. CO₂ was converted at 0.15-0.55 of CO₂/(CO + CO₂) ratio under H₂-rich condition (H₂/(CO + CO₂) = 2.0), highest conversion of 20.3% at 0.42. Further increasing CO₂ content decreased CO₂ conversion and quite amount of CO₂ acted as diluting component. For the syngas with low H₂ content or H₂/(CO + CO₂) ratio(< 1.85, H₂/CO = 2.0), the competitive adsorption of CO, H₂ and CO₂ resulted in low CO, CO₂ and total carbon conversion, which was 57.9%, 12.7% and 31.4% respectively at 0.74 of H₂/(CO + CO₂) ratio(H₂/CO/CO₂/N₂ = 40.8/20.4/34.8/4). FTS results indicated that high H₂ content and proper H₂/(CO + CO₂) ratio were favorable for the conversion of CO₂-containing syngas. More than 45% selectivity to gasoline-range hydrocarbons including isoparaffins was obtained under the two series of syngas. It was also tested that the catalytic activity of Co/SiO₂/HZSM-5 kept stable under CO₂-containing syngas(< 7.5%). And the quick catalytic deactivation under high CO₂ containing syngas(H₂/CO/CO₂/N₂ = 45.3/23.2/27.1/3.06) was due to carbon deposition and pore blockage by heavy hydrocarbon, tested by thermal gravimetry, N₂ physisorption and scanning electron microscopy(SEM).     

Microwave-assisted synthesis of SnS2/SnO2 composites by l-cysteine and their electrochemical performances when used as anode materials of Li-ion batteries

SnS₂/SnO₂ composites were prepared in a microwave-assisted reaction of a mixture solution of SnCl₄ and l-cysteine and were characterised by XRD, TEM, SEM and EDX. The influence of the mole ratio of SnCl₄ to l-cysteine (l-cys) on the sample was investigated. It was found that using a microwave method, SnS₂/SnO₂ composites were formed, and SnS₂/SnO₂ nanoparticles were obtained when the mole ratio of SnCl₄ to l-cysteine was 1:2. With higher contents of l-cys, when the mole ratio of SnCl₄ to l-cys was 1:4, the products were nanosheets instead of nanoparticles. Electrochemical tests demonstrated that the SnS₂/SnO₂ composites with layer structure exhibited high reversible capacities and good cycling performances when used as anode materials of Li-ion batteries. When the mole ratio of SnCl₄ to l-cys was 1:6, the initial reversible capacity of products was 593 mAh/g, and the retention capacity that was maintained was over 88%. Besides, the retention capacity of products was still excellent at high current charge/discharge.