A novel composite containing nanosized silicon and tin as anode material for lithium ion batteries

A novel composite consisting of nanosized Sn and Si as well as some lithium containing phases was synthesized by a mechanochemical reaction between SiO/SnO and Li using high energy mechanical milling (HEMM) with graphite as a dispersant, followed by a thermal treatment. The electrochemically active nanoclusters of Si and Sn derived by the mechanochemical reduction were uniformly distributed in the elastic matrix of lithium-containing phases and graphite. The difference in the reactive potential of Sn and Si with lithium was favorable for reducing the mechanical stress of the active hosts. Furthermore, the dispersion of Sn among the elastic matrix may contribute to an improved electrical connection among the Si based hosts and the current collectors. As a result, the composite presented a rechargeable capacity of 574.1 mAh g⁻¹ after 200 cycles. The capacity fading rate was thus calculated to be less than 0.2% per cycle. The cyclability of the composite was much superior to those of the SnO and SiO electrodes.     

Electrochemical reaction of the SiMn/C composite for anode in lithium ion batteries

The SiMn-graphite composite powder was prepared by mechanical ball milling and its electrochemical performances were evaluated as the candidate anode materials for lithium ion batteries. It is found that the cyclic performance of the composite materials is improved significantly compared to SiMn alloy and pure silicon. The heat treatment of the electrodes is beneficial for enhancing the cyclic stabilities. The SiMn-20 wt.% graphite composite electrode after annealing at 200 °C has an initial reversible capacity of 463 mAh g⁻¹ and a charge-discharge efficiency of 70%. Moreover, the reversible capacity maintains 426 mAh g⁻¹ after 30 cycles with a coulomb efficiency of over 97%. The phase structure and morphology of the composite were analyzed by X-ray diffraction (XRD) and scanning electron microscopy. The lithiation/delithiation behavior was investigated by electrochemical impedance spectroscopy (EIS) and cyclic voltammetry. The composite materials appear to be promising candidates as negative electrodes for lithium rechargeable batteries.     

Low temperature performance of graphite electrode in Li-ion cells

We studied low temperature performance of Li/graphite cell. Results show that capacity of the graphite electrode falls significantly in the temperature range of 0 to −20 °C. When lithiation and delithiation are both carried out at −20 °C, graphite only retains 12% of the room temperature capacity. However, delithiation capacity of graphite increases to 92% of the room temperature value if the lithiation is carried out at room temperature. We believe that the poor low temperature performance of the cell is due to slow kinetics of lithium ion diffusion in graphite rather than low ionic conductivity of electrolyte and solid electrolyte interface (SEI) on the graphite surface. During lithiation and delithiation processes, lithium ion has the similar apparent chemical diffusion coefficient of 10⁻⁹-10⁻¹⁰ cm²/s at 20 °C, depending on the state of lithiation of graphite. We observed a dramatic decrease in lithium ion diffusivity in the temperature range of 0 to −20 °C, and that at low temperatures of <−20 °C, lithium ion has higher diffusivity in the delithiated graphite than in the lithiated one. We also observed that temperature dependence of cycling behavior of the Li/graphite cell follows the change of lithium ion diffusivity.     

In situ Li nuclear magnetic resonance observation of the electrochemical intercalation of lithium in graphite; 1st cycle

We show a continuous, in situ nuclear magnetic resonance (NMR) experiment on a lithium/graphite electrochemical cell. The objective is to study a commercial graphite currently used as negative electrodes in secondary lithium batteries. A plastic cell is made, with metallic lithium as the counter electrode and 1 mol dm⁻³ LiPF₆/ethylene carbonate (EC) + diethylcarbonate (DEC) electrolyte. The reversible capacity is 346 mAh/g and the irreversible capacity 55 mAh/g, measured in the galvanostatic mode, at a rate of C/20 (20 h for the theoretical capacity of LiC₆) for the first cycle. We show the first discharge and the first charge of the cell inside the magnet and record simultaneously and regularly (in real time) static ⁷Li NMR spectra. As expected, we observe the quadrupolar lines characteristic of the lithium graphite intercalation compounds (GICs). During the discharge, the two types of in-plane densities of Li are successively found that correspond to the dilute LiC₉, then to the dense LiC₆ configuration; during the charge, we observe the successive decrease of these states. The galvanostatic curve helps to identify the stages NMR signature and the stages coexistence.     

A novel micro-spherical CoSn2/Sn alloy composite as high capacity anode materials for Li-ion rechargeable batteries

Micro-scaled spherical CoSn₂/Sn alloy powders synthesized from oxides of Sn and Co via carbothermal reduction at 800 °C were examined for use as anode materials in Li-ion battery. The phase composition and particle morphology of the CoSn₂/Sn alloy composite powders were investigated by XRD, SEM and TEM. The prepared CoSn₂/Sn alloy composite electrode exhibits a low initial irreversible capacity of ca. 140 mAh g⁻¹, a high specific capacity of ca. 600 mAh g⁻¹ at constant current density of 50 mA g⁻¹, and a good rate capability. The stable discharge capacities of 500-515 mAh g⁻¹ and the columbic efficiencies of 95.8-98.1% were obtained at current density of 500 mA g⁻¹. The relatively large particle size of CoSn₂/Sn alloy composite powder is apparently favorable for the lowering of initial capacity loss of electrode, while the loose particle structural characteristic and the Co addition in Sn matrix should be responsible for the improvement of cycling stability of CoSn₂/Sn electrode.     

Si-C-O glass-like compound/exfoliated graphite composites for negative electrode of lithium ion battery

Two low molecular weight silicone compounds, a cyclic type having vinyl groups and a chain-type having Si-H bonds, a catalyst for curing, and a catalyst regulator were mixed. The mixture was impregnated into exfoliated graphite (EG) by sorption, and cured in air at 200 °C. By this process cross-linked silicone coatings were formed on graphite flakes. The composites of Si-C-O glass-like compounds and EG were synthesized by heat treatment of this precursor at 1000-1400 °C for 1 h in argon. The composites formed at 1000-1300 °C were amorphous by XRD and had practically the same chemical composition: Si 44-45, C 27-29, O 25-26, H < 0.5, all in mass%. The ²⁹Si MAS-NMR spectra indicated that the compound formed at 1000 °C was mainly composed of siloxane bonds and amorphous silica, whereas in the compound formed at 1300°C, Si-C bonds and amorphous silica were predominant. The insertion/extraction characteristics of lithium ions for the electrode prepared with composite:poly(vinylidene fluoride) = 90:10 mass% were examined in 1 mol L⁻¹ LiClO₄ solution of ethylene carbonate:diethyl carbonate = 50:50 vol%. High, 650-700 mA h g⁻¹, capacities and steady cycle performance at 50 mA g⁻¹ were achieved with the composites formed at 1250-1300 °C. Capacities of the composites formed at 1200 °C and lower were initially higher but decreased with increasing number of cycles. The composites formed at 1350 °C showed good cycle performance but the capacity was about 500 mA h g⁻¹ due to the formation of β-SiC. Except for the first cycle, the capacity-potential characteristics were similar to those of hard carbons and the coulomb efficiency was 95-100%. For all the composites the capacity was larger than that of graphite (372 mA h g⁻¹) in the range of 50-200 mA g⁻¹. Due to the large insertion capacity of the first cycle, the efficiency was low (60-70%) at first. By short-circuiting the working electrode to the lithium foil counter electrode for a certain period, the irreversible capacity of the first cycle was almost eliminated. It indicates that direct doping of lithium ions into composites is a promising way to increase the efficiency of the first cycle.     

Compatibility of quaternary ammonium-based ionic liquid electrolytes with electrodes in lithium ion batteries

Electrochemical intercalation/deintercalation behavior of lithium into/from electrodes of lithium ion batteries was comparatively investigated in 1 mol/L LiClO₄ ethylene carbonate-diethyl carbonate (EC-DEC) electrolyte and a quaternary ammonium-based ionic liquid electrolyte. The natural graphite anode exhibited satisfactory electrochemical performance in the ionic liquid electrolyte containing 20 vol.% chloroethylenene carbonate (Cl-EC). This is attributed to the mild reduction of solvated Cl-EC molecules at the graphite/ionic electrolyte interface resulting in the formation of a thin and homogenous SEI on the graphite surface. However, rate capability of the graphite anode is poor due to the higher interfacial resistance than that obtained in 1 mol/L LiClO₄/EC-DEC organic electrolyte. Spinel LiMn₂O₄ cathode was also electrochemically cycled in the ionic electrolyte showing satisfactory capacity and reversibility. The ionic electrolyte system is thus promising for 4 V lithium ion batteries based on the concept of “greenness and safety”.     

Electrochemical intercalation of aluminium chloride in graphite in the molten sodium chloroaluminate medium

Aluminium chloride intercalation in graphite was studied by anodic oxidation of compacted graphite (rod) and graphite powder electrodes in sodium chloroaluminate melt saturated with sodium chloride at 175 °C. The studies carried out by employing both galvanostatic and cyclic voltammetric techniques had shown that the intercalation reactions take place only beyond the chlorine evolution potential of +2.2 V vs. Al on both the electrodes. The extent of intercalation reaction was directly related to the anodic potential and probably to the amount of chlorine available on the graphite anodes. In the case of graphite powder electrode, a distinctly different redox process was observed at sub-chlorine evolution potentials and this was attributed to the adsorption of chlorine on its high surface area. This finding contradicts a report in the literature that the intercalation reactions occur at potentials below chlorine evolution in the chloroaluminate melt.     

Electrochemical behavior of lithium intercalated in a molybdenum disulfide-crown ether nanocomposite

A new nanocomposite, obtained from the intercalation of the cyclic ether 12-Crown-4 into MoS₂, Li_0.32MoS₂(12-Crown-4)_0.19, is described. The laminar product has an interlaminar distance of 14.4 Å. The electrical conductivity of the nanocomposite varies from 2.5 × 10⁻² to 4.3 × 10⁻² S cm⁻¹ in the range 25-77 °C, being about four times higher than the analogous poly(ethylene oxide) (PEO) derivative at room temperature. The electrochemical step-wise galvanostatic intercalation or de-intercalation of lithium, leading to Li_xMoS₂(12-Crown-4)_0.19 with x in the range 0.07-1.0, indicates a Li/Li⁺ pair average potential of 2.8 V. The electrochemical lithium diffusion coefficients in the crown ether intercalates, determined by galvanostatic pulse relaxation between 15 and 37 °C at different lithium intercalation degrees, are higher than those of the PEO derivatives under similar conditions, being however the diffusion mechanism rather more complex. The variation of both, the lithium diffusion activation enthalpy and the quasi-equilibrium potentials, with the lithium content shows there are two different limit behaviors, at low and high lithium intercalation degree, respectively. These features are discussed by considering the high stability of the Li-crown ether complex and the different chemical environments found by lithium along the intercalation process.     

Electrochemical intercalation of lithium into a natural graphite anode in quaternary ammonium-based ionic liquid electrolytes

Electrochemical intercalation of lithium into a natural graphite anode was investigated in electrolytes based on a room temperature ionic liquid consisting of trimethyl-n-hexylammonium (TMHA) cation and bis(trifluoromethanesulfone) imide (TFSI) anion. Graphite electrode was less prone to forming effective passivation film in 1 M LiTFSI/TMHA-TFSI ionic electrolyte. Reversible intercalation/de-intercalation of TMHA cations into/from the graphene interlayer was confirmed by using cyclic voltammetry, galvanostatic measurements, and ex situ X-ray diffraction technique. Addition of 20 vol% chloroethylenene carbonate (Cl-EC), ethylene carbonate (EC), vinyl carbonate (VC), or ethylene sulfite (ES) into the ionic electrolyte resulted in the formation of solid electrolyte interface (SEI) film prior to TMHA intercalation and allowed the formation of Li-C₆ graphite interlayer compound. In the ionic electrolyte containing 20 vol% Cl-EC, the natural graphite anode exhibited excellent electrochemical behavior with 352.9 mAh/g discharge capacity and 87.1% coulombic efficiency at the first cycle. A stable reversible capacity of around 360 mAh/g was obtained in the initial 20 cycles without any noticeable capacity loss. Mechanisms concerning the significant electrochemical improvement of the graphite anode were discussed. Ac impedance and SEM studies demonstrated the formation of a thin, homogenous, compact and more conductive SEI layer on the graphite electrode surface.     

TiO2 nanotube arrays annealed in CO exhibiting high performance for lithium ion intercalation

Anatase titania nanotube arrays were fabricated by means of anodization of Ti foil and annealed at 400 °C in respective CO and N₂ gases for 3 h. Electrochemical impendence spectroscopy study showed that CO annealed arrays possessed a noticeably lower charge-transfer resistance as compared with arrays annealed in N₂ gas under otherwise the same conditions. TiO₂ nanotube arrays annealed in CO possessed much improved lithium ion intercalation capacity and rate capability than N₂ annealed samples. At a high charge/discharge current density of 320 mA g⁻¹, the initial discharge capacity in CO annealed arrays was found to be as high as 223 mAh g⁻¹, 30% higher than N₂ annealed arrays, ∼164 mAh g⁻¹. After 50 charge/discharge cycles, the discharge capacity in CO annealed arrays remained at ∼179 mAh g⁻¹. The improved intercalation capacity and rate capability could be attributed to the presence of surface defects like Ti-C species and Ti³⁺ groups with oxygen vacancies, which not only improved the charge-transfer conductivity of the arrays but also possibly promoted phase transition.     

Calorimetric investigation of the reactivity of the passivation film on lithiated graphite at elevated temperatures

Thermal storage of lithiated graphite electrodes has been performed between 40 and 90 °C for 8 h to 3 weeks. The results were compared for two separators: Celgard 2402 and a microporous PVdF membrane. The effects of storage on the capacity losses have been discussed with respect to the passivation film on the graphite electrodes in contact with the electrolyte solution EC:DMC:DEC (2:2:1)-1 M LiPF₆. The capacity loss shows a thermally activated character, which has been related to transformations of the passivation film at moderate temperatures. At higher temperatures, reaction of the intercalated lithium takes place, controlled by Li⁺-ion diffusion. DSC measurements were performed on passivated and lithiated graphite electrodes. Two peaks could be distinguished. An effect of the elevated temperature storage on the intensity and onset temperature of the first peak in DSC is evidenced. This peak could be attributed to the transformation of the passivation film. The second peak is due to the diffusion of lithium ions and the subsequent reaction with the liquid electrolyte.The effect of washing the electrode with DMC was thoroughly investigated. Our results allowed to attribute the transformation of the passivation film upon DSC analysis to a reaction taking place in the presence of LiPF₆.     

Electrochemistry of Sn(II)/Sn in a hydrophobic room-temperature ionic liquid

The electrochemical reaction of Sn(II)/Sn was investigated in a room-temperature ionic liquid, 1-n-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide (BMPTFSI) at 25 °C. The anodic dissolution of Sn metal proceeded by a two-electron transfer reaction with a current efficiency of nearly 100%. Electrodeposition of Sn on a Cu substrate is possible in BMPTFSI containing Sn(II). The formal potential of the Sn(II)/Sn is −0.57 V vs. Ag/Ag(I). The diffusion coefficient of Sn(II) was estimated to be ∼1 × 10⁻⁷ cm² s⁻¹ from chronoamperometric and chronopotentiometric techniques. The initial stage of nucleation of Sn on a polycrystalline Pt substrate was found to be classified into a three-dimensional progressive nucleation under diffusion control by chronoamperometry, suggesting the rate of nucleation is faster than that of crystal growth.     

Electrochemical properties of heat-treated polymer-derived SiCN anode for lithium ion batteries

Silicon-carbon-nitrogen material (SiCN) is pyrolyzed from polysilylethylenediamine (PSEDA) derivation, followed by a heat-treating process at 1000 °C in Ar atmosphere. This heat-treated SiCN material has an excellent electrochemical performance as an anode for lithium ion batteries. Charge-discharge cycle measurements show that the heat-treated SiCN material exhibits a high first cycle discharge capacity of 829.0 mAh g⁻¹ and stays between 400 and 370 mAh g⁻¹ after 30 cycles. The discharge capacity remains above 300 mAh g⁻¹ at the high current density of 80 and 160 mA g⁻¹. These values are higher than untreated SiCN and commercial graphite anodes, which indicates that the heat-treating process improves the charge-discharge capacity, cycle stability and high-rate ability of SiCN anode. It is seemed that changes of SiCN structure, the formation of loose nano-holes on material surface and the formation of graphitic carbon phase in heat-treating process contribute to the improvement of electrochemical properties for SiCN anode.     

Comparisons of graphite and spinel Li1.33Ti1.67O4 as anode materials for rechargeable lithium-ion batteries

The aim of this work was to compare the electrochemical behaviors and safety performance of graphite and the lithium titanate spinel Li_1.33Ti_1.67O₄ with half-cells versus Li metal. Their electrochemical properties in 1 M LiPF₆/EC + DEC (1:1 w/w) or 1 M LiPF₆/PC + DEC (1:1 w/w) at room and elevated temperatures (30 and 60 °C) have been studied using galvanostatic cycling. At 30 °C graphite has higher reversible capacity than Li_1.33Ti_1.67O₄ when using the LiPF₆/EC + DEC as electrolyte. At 60 °C graphite declines in cell capacity yet Li_1.33Ti_1.67O₄ remains almost unchanged. In a propylene carbonate (PC) containing electrolyte, graphite electrode exfoliates and loses its mechanical integrity while Li_1.33Ti_1.67O₄ electrode is very stable. An accelerating rate calorimeter (ARC) and microcalorimeter have been used to compare the thermal stability of lithiated lithium titanate spinel and graphite. Results show that Li_1.33Ti_1.67O₄ may be used as an alternative anode material offering good battery performance and higher safety.     

Electrochemical insertion of sodium into graphite in molten sodium fluoride at 1025 °C

The electrochemical insertion of sodium into graphite was studied in molten sodium fluoride at 1025 °C. The results obtained evidenced two mechanisms for sodium insertion into graphite: sodium intercalation between the graphite layers and sodium sorption into the porosity of the material. Subsequent internal rearrangement of inserted sodium occurred, via transference from the pores towards the intercalation sites. In addition, the intercalation compound was found to undergo a fast decomposition process (k = 2.55 × 10⁻⁹ mol s⁻¹). X-ray diffraction analysis was used to confirm the formation of a high stage compound (Na_0.1C₈), the composition of which was consistent with compositions observed in the case of chemical vapor and electrochemical insertion of sodium, during experiments in the sodium perchlorate-ethylene cabonate electrolyte.     

High porous carbon with Cu/ZnO nanoparticles made by the pyrolysis of carbon material as a catalyst for steam reforming of methanol and dimethyl ether

Cu/ZnO/carbon catalysts for steam reforming reactions were prepared by the technique to obtain much amount of metals highly dispersed on the porous carbon. The preparation method includes the carbonization of an ion exchange resin loaded with metal cations. By containing ZnO in the resin, the agglomeration of Cu particle during the carbonization was suppressed within the carbon matrix due to the difference in the behavior of carbonization and migration between Cu and Zn in the same ion exchange resin, and the Cu particle size was reduced. Thus, the obtained Cu3Zn1 catalyst had more than double the Cu surface area of the catalyst contained only Cu, regardless of lower Cu content. Methanol steam reforming test showed that the catalysts’ activity was positively correlated with Cu surface area. Also in dimethyl ether (DME) steam reforming reactions using the composite catalysts with γ-Al₂O₃, the catalytic activity tracked with the surface area covered by Cu. The optimized Cu/ZnO/carbon catalyst composite showed a high DME conversion of 0.87 even at the low temperature of 300 °C and with GHSV = 2000 h⁻¹, which was due to high dispersion of Cu on the micropore structure of carbon support.     

Storage behavior of LiNi1/3Co1/3Mn1/3O2/artificial graphite Li-ion cells

A series of Li-ion cells containing LiNi_1/3Co_1/3Mn_1/3O₂ and artificial graphite as the active materials, have been stored at various temperatures from 0 to 70 °C. The 3-electrode impedance study shows that both the solid electrolyte interphase (SEI) film resistance and charge-transfer resistance of the negative electrode first decrease and then increase during storage at 70 °C, while both resistances for the positive electrode increase under this condition. The reversible capacity loss of the 3-electrode cell, which is possibly attributed to dissolution of SEI film, accounts for over half of the total capacity loss after 5 weeks of storage. Gases generated from the swelling aged cell at 60 °C are mainly attributed to the reduction of the electrolyte on the negative electrode. A further study on the side-reaction has been done on graphite electrodes and separators, indicating that SEI films may be rearranged and reformed on negative electrodes, and that some pores on the positive electrode side of separator are blocked due to the oxidation of electrolyte, resulting in poor Li-ion transfer and rise of the ohmic resistance during storage at elevated temperature. However, at 0 °C, this side-reaction is impeded.     

Novel tin-graphite composites as negative electrodes of Li-ion batteries

For the purpose of obtaining an improved performance of the graphite negative electrode of Li-ion batteries, a novel graphite-tin composite has been synthesized by reduction of tin chloride (SnCl₂) with KC₈ in THF medium. This composite contains nano-sized tin particles dispersed on the graphite surface and free tin aggregates. Lithium electrochemical insertion occurs both in graphite and in tin. An experimental reversible specific charge of 489 mA h g⁻¹ is found stable upon cycling. Such a value is lower than the maximum theoretical one of 609 mA h g⁻¹ suggesting that only a part of tin is involved in the lithium insertion/extraction process. This part of active tin responsible for the stable capacity could be that bound to graphite. To the contrary, free tin aggregates could contribute to an extra capacity that decreases upon cycling in relation with the volume changes that occurs during alloying/dealloying.     

Ultrafine SnO2 dispersed carbon matrix composites derived by a sol-gel method as anode materials for lithium ion batteries

Ultrafine crystalline SnO₂ particles (2-3 nm) dispersed carbon matrix composites are prepared by a sol-gel method. Citric acid and hydrous SnCl₄ are used as the starting constituents. The effect of the calcination temperatures on the structure and electrochemical properties of the composites has been studied. Structure analyses show that ultrafine SnO₂ particles form and disperse in the disordered carbon matrix in the calcination temperature range of 500-800 °C, forming SnO₂/C composites, and the carbon content shows only a slight increase from 35.8 wt.% to 39.1 wt.% with the temperature. Nano-Sn particles form when the calcination temperature is increased to 900 °C, forming a SnO₂/Sn/C composite, and the carbon content is increased to 49.3 wt.%. Electrochemical testing shows that the composite anodes provide high reversible cycle stability after several initial cycles, maintaining capacities of 380-400 mAh g⁻¹ beyond 70 cycles for the calcination temperature of 600-800 °C. The effect of the structure feature of the ultrafine size of SnO₂ and the disordered carbon matrix on the lithium insertion and extraction process, especially on the reversible behavior of the lithium ion reaction during cycling, is discussed.