Grain boundaries and the influence of the ionophilic-ionophobic balance on Li and F NMR and conductivity in low-dimensional polymer electrolytes with lithium tetrafluoroborate

⁷Li and ¹⁹F NMR linewidths and impedance spectra are reported for low-dimensional CmOn (I):LiBF₄ mixtures. Data for the ionophilic polymer C18O5 is compared with that for the ionophobic C18O1 and the block copolymer C16O1O5(21%) (21 mol% of C16O5). In C18O5:LiBF₄ (1:1) narrow ⁷Li linewidths, which were observed in the liquid crystal phase above the side chain melting temperature (∼50 °C), persist in the crystal down to ca. 0 °C and broaden below −20 °C. However, in C18O1:LiBF₄ (1:0.6) narrow ⁷Li linewidths were also observed down to −20 °C suggesting highly mobile neutral aggregates of salt since this system is non-conductive. In the copolymer C16O1O5(21%):LiBF₄ (1:0.7) the linewidths were even narrower down to −70 °C with weak temperature dependence. In all systems ¹⁹F linewidths were significantly broader than ⁷Li linewidths. The complex plane plots obtained by impedance spectroscopy exhibit characteristic minima identified with ‘grain boundary’ resistance and, following heat treatment, minima with weak temperature dependence identified with ‘internal crystal’ resistance, R_i, and conductivities, σ_i ≥ 10⁻⁴ S cm⁻¹. Four-component mixtures of copolymers CmO1O5 and CmO1O4 with LiBF₄ and ‘salt-bridge’ poly(tetramethylene oxide)-dodecamethylene copolymers gave conductivities of ca. 4 × 10⁻⁴ S cm⁻¹ at 20 °C with weak temperature dependence. A novel carrier-hopping mechanism of lithium transport decoupled from side chain melting in the crystalline state is postulated.      

New amphiphilic fluorescent CBABC-type pentablock copolymers containing pyrene group by two-step atom transfer radical polymerization (ATRP) and its self-assembled aggregation

A series of novel amphiphilic fluorescent CBABC-type pentablock copolymers (Py-PMMA-PEG4600-PMMA-Py) were prepared from BAB-type amphiphilic triblock copolymer (PMMA-PEG4600-PMMA) as macroinitiator with various contents of 1-(methacryloyloxyethylamino-carboxylmethyl) pyrene (PyMOI) by atom transfer radical polymerization (ATRP) in toluene using CuBr/2,2-bipyridine as catalyst system. Triblock copolymer (PMMA-PEG4600-PMMA) was prepared by ATRP and obtained from Br-PEG4600-Br as macroinitiator with methyl methacrylate in tetrahydrofuran using the same catalyst. The molecular weights of pentablock copolymers which were reinitiated by PMMA-PEG4600-PMMA macroinitiator were calculated from ¹H NMR spectra up to 42,400 gmol⁻¹. The polydispersity of pentablock copolymers obtained from GPC analysis was narrow between 1.10 and 1.38. The crystallinity of triblock copolymer (PMMA-PEG4600-PMMA) was decreased slightly with incorporating PMMA segment. Introducing the bulky pyrene substituent into pentablock copolymer, the melting temperature was not observed and all pentablock copolymers showed amorphous patterns in wide-angle X-ray scattering (WAXS) due to decrease in the degree of crystallinity of polymer chain because of disturbing regular packing. The temperatures at 10% weight loss (Td₁₀), examined by TG analysis, showed values ranging from 265 to 323 °C in nitrogen and 264 to 313 °C in air. Fluorescence spectra of Py-PMMA-PEG4600-PMMA-Py exhibited stronger excimer emission at ca. 480 nm due to the aggregations of pyrene group formed via interaction of the hydrophobic chains. The more content of PyMOI segment in pentablock copolymers can obtain the higher emission intensity ca. 480 nm. When there were higher PyMOI contents (84.9 wt% PyMOI) in pentablock copolymers, they formed larger aggregates (210 nm) in SEM micrographs. On the other hand, while increasing the concentration of the polymer solution in THF, the morphology was changed from spherical (0.1 mg/mL) to chainlike (1.0 mg/mL) aggregates.     

Synthesis, optical and electrochemical properties of luminescent polymers containing 1,2-diphenylmaleimide and thiophene segments

In an attempt to balance energy barriers of hole and electron injection we prepared and characterized homopolymer containing electron-transporting 1,2-diphenylmaleimide chromophores (P1) and copolymers consisting of 1,2-diphenylmaleimide and hole-transporting 2,5-thiophene moieties (P2, P3) via dehalogenation polycondensation. The copolymers are amorphous materials with decomposition temperature greater than 450 °C. Absorption and fluorescence spectra were employed to investigate their optical properties both in solution and film state. Photoluminescence maxima of P1, P2 and P3 films are 564, 559 and 558 nm, respectively. The HOMO and LUMO energy levels have been estimated from their cyclic voltammograms. The HOMO levels of P1, P2, and P3 were readily raised with increasing thiophene content (−5.99, −5.59, and −5.43 eV, respectively), whereas their LUMO levels were very similar (−3.61 to −3.65 eV). Double-layer light-emitting diodes (Al/PEDOT:PSS/P1-P3/ITO) were fabricated to evaluate their optoelectronic characteristics. Incorporation of thiophene units successfully reduced the turn-on electric field from 11.0×10⁵ to 2.9×10⁵ V/cm, but it decreased the luminescent efficiency and the maximum brightness.     

Electrochemical study of stable N-alkoxyarylaminyl radicals

The electrochemical study of N-tert-butoxy-2,4-diphenyl-6-tert-butylphenylaminyl (1a), N-tert-butoxy-2,4-bis(4-chlorophenyl)-6-tert-butylphenylaminyl (1b), N-[2-(methoxycarbonyl)-2-propyl]-2,4-diphenyl-6-tert-butylphenylaminyl (2), and N-tert-butoxy-2,4,6-tris(4-chlorophenyl)phenylaminyl radicals (3) was performed by cyclic voltammetry using acetonitrile as the solvent and Bu₄NPF₆ as the supporting electrolyte. On cathodic scan (100 mV/s), all the radicals gave chemically reversible cyclic voltammograms, and the were determined to be −1.405 V (1a), −1.310 V (2a), −1.282 V (2b), and −1.195 V (3) (versus Fc⁺/Fc), respectively. On anodic scan (100 mV/s), on the other hand, 1a, 1b and 2 showed chemically reversible cyclic voltammograms, but 3 exhibited a partially reversible couple even on a scan rate of 500 mV/s, indicating that the cation species of 3 was less stable. The determined for 1a, 1b, 2 and 3 were 0.220, 0.280, 0.318 and 0.294 V (versus Fc⁺/Fc), respectively. The electrochemical data were compared with those of thioaminyl radicals, the corresponding sulfur analogues of 1-3.     

Synthesis of laterally attached side-chain liquid crystalline poly(p-phenylene vinylene) and polyfluorene derivatives for the application of polarized electroluminescence

Two series of poly(p-phenylene vinylene) and polyfluorene derivatives (PPV1-PPV4 and PF1-PF5) containing laterally attached penta(p-phenylene) mesogenes were synthesized and characterized. These polymers show nematic liquid crystalline behavior. The optical properties of the polymers were investigated by UV-vis absorption and photoluminescence spectrometers and these polymers were fabricated to form the polarized electroluminescent devices using poly(ethylenedioxythiophene)-poly(styrene sulfonic acid) (PEDOT-PSS) as an alignment layer. In the series of poly(p-phenylene vinylene) derivatives, polymer PPV4 offered the best EL device performance. It emitted yellow light at 588 nm at 4 V. The maximum brightness was about 1337 cd/m² at 9 V with a polarized ratio of 2.6. In another series of polyfluorene derivatives, PF4 offered the best EL device performance with the polarized ratio of 12.4 and a maximum luminescence of 1855 cd/m². In the case of polarized white light, as a consequence of blending small amount of PF4 and PF5 with a host polymer PF2, polarized ratio of up to 10.2 and a maximum brightness of 2454 cd/m² have been attained. The aligned films exhibited pronounced polarized ratio, implying that the polymers exhibit potential for linearly polarized LED application.     

Synthesis and characterization of chiral polythiophenes: Poly [(R)-(−) and (S)-(+)-2-(3′-thienyl)ethyl N-(3″,5″-dinitrobenzoyl)-α-phenylglycinate]

(R)-(−) (1) and (S)-(+)-2-(3′-Thienyl)ethyl N-(3″,5″-dinitrobenzoyl)-α-phenylglycinate (2) monomers were synthesized, characterized, and polymerized in chloroform using FeCl₃ as an oxidizing agent. Molecular weights of 2.6 × 10⁴ and 3.2 × 10⁴ for poly1 and poly2, respectively, were determined by SEC analysis. FTIR spectra of the polymers indicated the coupling of monomers through the α positions. UV-vis spectra showed absorption bands at λ_max = 226 and 423 nm for poly1 and poly2, ascribed to transitions of side groups and polythiophene backbone, respectively. Poly1 and poly2 remained stable up to 210 °C. At higher temperatures, a two step weight loss degradation process was observed for both polymers by TGA analysis. ¹H NMR, in the presence of Eu(tfc)₃, and optical rotation measurements indicate the chiral properties of the monomers 1 ([α]_D²⁸ = −76.2) and 2 ([α]_D²⁸ = +76.0), and the maintenance of chirality after polymerization (poly1 [α]_D²⁸ = −29.0 and poly2 [α]_D²⁸ = +28.4, c = 2.5 in THF). According to scanning electron microscopic analysis, the polymers are highly porous.     

New host copolymers containing pendant triphenylamine and carbazole for efficient green phosphorescent OLEDs

A series of vinyl copolymers (P1-P6) containing pendant hole-transporting triphenylamine (11-88 mol%) and carbazole chromophores were synthesized by radical copolymerization to investigate the influence of triphenylamine groups upon optoelectronic properties. The copolymers were readily soluble in common organic solvents and their weight-average molecular weights (M_ws) were between 1.41 × 10⁴ and 2.24 × 10⁴. They exhibited moderate thermal stability with T_d = 402-432 °C at 5% weight loss. The emission spectra (both PL and EL) of the blends [P1-P6 with 4 wt% Ir(ppy)₃] showed dominant green emission (517 nm) attributed to Ir(ppy)₃ due to efficient energy transfer from P1-P6 to Ir(ppy)₃. The HOMO levels of P1-P6, estimated from onset oxidation potentials in cyclic voltammeter, were −5.42 to −5.18 eV, which are much higher than −5.8 eV of conventional poly(9-vinylcarbazole) (PVK) host owing to high hole-affinity of the triphenylamine groups. The optoelectronic performances of phosphorescent EL devices, using P1-P6 as hosts and Ir(ppy)₃ as dopant (ITO/PEDOT:PSS/P1-P6:Ir(ppy)₃ (4 wt%):PBD (40 wt%)/BCP/Ca/Al), were greatly improved relative to that of PVK. The best performance was obtained with P4 device, in which the maximum luminance and luminance efficiency were 11?501 cd/m² and 10.6 cd/A, respectively.     

Photosensitive poly(benzoxazole) based on precursor from diphenyl isophthalate and bis(o-aminophenol)

A new synthetic method for the preparation of poly(benzoxazole) (PBO) precursor, poly(o-hydroxyamide) (7) from bis(o-aminophenol) (5) and diphenyl isophthalate (6) has been developed. Polymer 7 was prepared by the polycondensation of 5 and 6 in 1-methyl-2-pyrrolidinone (NMP) at 185-205 °C. Model reactions were carried out in detail to elucidate appropriate conditions for the formation of 2-hydroxybenzanilide (3) from o-aminophenol (1) and phenyl benzoate (2). The photosensitive (PBO) precursor based on polymer 7 containing a 22% of benzoxazole unit and 30 wt% 1-{1,1-bis[4-(2-diazo-1-(2H)naphthalenone-5-sulfonyloxy)phenyl]ethyl}-4-{1-[4-(2-diazo-1(2H)naphthalenone-5-sulfonyloxy)phenyl]methylethyl}benzene (S-DNQ) showed a sensitivity of 110 mJ cm⁻² and a contrast of 5.0 when it was exposed to 436 nm light followed by developing with a 2.38 wt% aqueous tetramethylammonium hydroxide solution at room temperature. A fine positive image featuring 8 μm line and space patterns was observed on the film of the photoresist exposed to 200 mJ cm⁻² of UV-light at 436 nm by the contact mode.     

Copolymers containing pendant styryltriphenylamine and carbazole groups: Synthesis, optical, electrochemical properties and its blend with Ir(ppy)3

A series of vinyl copolymers (PVKST12-PVKST91) and homoploymer PVST containing pendant hole-transporting 4-(4-oxystyryl)triphenylamine (12-100 mol%) and carbazole chromophores were synthesized by radical copolymerization and employed as host for Ir(ppy)₃ phosphor to tune emission color. They were characterized using the ¹H NMR, FT-IR, absorption and photoluminescence spectra, elemental analysis, GPC, cyclic voltammetric and thermal analysis (DSC, TGA). Their weight-average molecular weights (M_w) and decomposition temperatures (T_d) were 1.46-5.68 × 10⁴ and 356-399 °C, respectively. The HOMO levels of PVKST12-PVKST91 and PVST, estimated from the onset oxidation potentials in cyclic voltammograms, were −5.40 to −5.14 eV, which are much higher than −5.8 eV of the conventional host poly(9-vinylcarbazole) (PVK) owing to high hole-affinity of the 4-(4-oxystyryl)triphenylamine groups. Therefore, copolymers PVKST are effective in reducing hole-injection barrier between the PEDOT:PSS and emitting layer. Electroluminescent devices [ITO/PEDOT:PSS/PVKST:Ir(ppy)₃:PBD/BCP/Ca/Al] using the hole-transporting PVKST as host were fabricated to tune the emission color. Their EL spectra showed a major emission at 515 nm and a minor peak at 435 nm attributed to Ir(ppy)₃ and 4-(4-oxystyryl)triphenylamine, respectively. The C.I.E. 1931 coordinates shift from (0.29, 0.61) for PVK to (0.33, 0.42) for PVST with an increase in 4-(4-oxystyryl)triphenylamine content.     

Synthesis, electroluminescence, and photovoltaic properties of dendronized poly(p-phenylene vinylene) derivatives

Two dendronized poly(p-phenylene vinylene) (PPV) derivatives, ED-PPV and BB-PPV, have been successfully synthesized according to the Gilch route. The obtained polymers possess excellent solubility in common solvents, good thermal stability with 5% weight loss temperature of more than 340 °C. The weight-average molecular weight (M_w) and polydispersity index (PDI) of ED-PPV and BB-PPV are in the range of (1.26-2.34)×10⁵ and 1.37-1.45, respectively. Polymer light-emitting diodes (PLEDs) with the configuration of ITO/PEDOT:PSS/polymer/Ca/Al devices were fabricated, and the PLEDs emitted green-yellow light. The turn-on voltages of the PLEDs based on ED-PPV and BB-PPV were approximately 4.3, and 4.5 V, respectively. The PLED devices of ED-PPV exhibited the maximum luminance of about 157 cd/m² at 10.5 V. Photovoltaic cells with the configuration of ITO/PEDOT:PSS/polymer:C₆₀ (1:1)/Al were also fabricated, and the energy conversion efficiency of the devices based on ED-PPV and BB-PPV was measured to be 0.58, and 0.014%, respectively, under the white light at 75 mW/cm².     

The direct synthesis of wholly aromatic poly(p-phenylene)s bearing sulfobenzoyl side groups as proton exchange membranes

Sulfonated poly(p-phenylene)s (SPPs) containing sulfonic acid groups in their side chains had been directly synthesized by Ni(0) catalytic coupling of sodium 3-(2,5-dichlorobenzoyl)benzenesulfonate and 2,5-dichlorobenzophenone. The synthesized copolymers possessed high molecular weights revealed by their high viscosity, and the formation of tough and flexible membranes by casting from DMAc solution. The copolymers exhibited excellent oxidative stability and mechanical properties due to their fully aromatic structure extending through the backbone and pendent groups. Transmission electron microscopic (TEM) analysis revealed that these side-chain type SPP membranes have a microphase-separated structure composed of hydrophilic side-chain domains and hydrophobic polyphenylene main chain domains. The proton conductivities of copolymer membranes increased with the increase of IEC and temperature, reaching values above 3.4 × 10⁻¹ S/cm at 120 °C, which are almost 2-3 times higher than that of Nafion 117 at the same measurement conditions. Consequently, these materials proved to be promising as proton exchange membranes.     

Structure-property relationships for a series of polyimide copolymers with sulfonated pendant groups

A series of high molecular weight, sulfonated polyimide copolymers (8a-f) with controlled acid contents have been obtained using 2,2′-bis(4-sulfobenzyloxy)benzidine (14) prepared via a flexible synthetic route. This series of novel sulfonated polyimide membranes were found to possess higher hydrolytic stability than polyimides in which the sulfonic acid groups are bound directly to the polymer main chain. An in-depth analysis of conductivity data was also performed for 8 and compared to the results for Nafion^® (1), sulfonated poly(ether ether ketone) (2) and a main-chain sulfonated polyimide (3). In order to remove the influence of acid strength, the proton mobility value for 8 at infinite dilution was calculated and found to be 1.2(±0.6) × 10⁻³ cm² s⁻¹ V⁻¹. A catalyst-coated membrane (CCM)-MEA based on a polyimide incorporating 60% sulfonated monomer (8d) was found to exhibit comparable beginning-of-life fuel cell performance as a Nafion^®-based CCM MEA at 50 °C.     

Novel red-emitting thieno-[3,4-b]-pyrazine derivatives suitable for vacuum evaporation and solution method to fabricate non-doped OLEDs

Two novel red-emitting thieno-[3,4-b]-pyrazine-cored molecules with phenyls (TP) or polyphenyls (Müllen type dendron, DTP) as peripheral groups were designed and synthesized. They have large Stokes shifts over 100 nm. DTP is thermally stable with decomposition temperature up to 458 °C. More importantly, it is amorphous with a remarkably high glass transition temperature of 262 °C. DTP can be made into thin films either by solution method or vacuum evaporation. Red OLEDs were fabricated using either spin coated or vacuum evaporated DTP film as emitting layer. The evaporated device exhibited a maximum brightness of 1753 cd m⁻² and a luminous efficiency of 0.74 cd A⁻¹, which are among the best data ever reported for thieno-[3,4-b]-pyrazine derivatives so far. In contrary, TP failed to produce satisfied red emission in its evaporated OLEDs.     

Living radical polymerization of styrene mediated by a piperidinyl-N-oxyl radical having very bulky substituents

A new cyclic nitroxide 1 and the corresponding alkoxyamines 9 and 10 were synthesized and the polymerization of styrene (St) initiated with 10 was investigated. The NO-C bond of 9 is very weak, cleaving at room temperature. On the other hand, alkoxyamine 10 is stable at room temperature and the A_act and E_act for the NO-C bond homolysis were determined to be 1.4 × 10¹⁵ s⁻¹ and 124.5 kJ mol⁻¹, respectively. When the polymerization of St was carried out at 70 °C, the resultant poly(St) showed narrow polydispersities below 1.25. In the polymerization at 90 °C, the resulting poly(St) showed narrow polydispersity until 60% conversion, but M_w/M_n was rapidly increased above 60% conversion. On the other hand, the polymerization at 120 °C gave poly(St) with broad polydispersities. The unusual polymerization behavior was discussed on the basis of the SEC and ESR results.     

Synthesis of sulfonated poly(arylene-co-naphthalimide)s as novel polymers for proton exchange membranes

A series of novel sulfonated poly(arylene-co-binaphthalimide)s (SPPIs) were successfully synthesized via Ni(0) catalytic coupling of sodium 3-(2,5-dichlorobenzoyl)benzenesulfonate and bis(chloronaphthalimide)s. Bis(chloronaphthalimide)s were conveniently prepared from 5-chloro-1,8-naphthalic anhydride and various diamines. Tough and transparent SPPI membranes were prepared and the electrolyte properties of the copolymers were intensively investigated as were the effects of different diamine structures on the copolymer characterisitics. The copolymer membrane Ia-80, with an ion exchange capacity (IEC) of 2.50 meq g⁻¹, displayed a higher proton conductivity, i.e. 0.135 S cm⁻¹ at 20 °C, as compared to Nafion 117 (0.09 S cm⁻¹, 20 °C). The copolymer membrane Id-70, containing 3,3′-dimethyl-4,4′-methylenedianiline (DMMDA) units, exhibited excellent stability toward water and oxidation due to the introduction of hydrophobic methyl groups on the ortho-position of the imido bond in the copolymer. The mechanical property of Id-70 remained virtually unchanged after immersing membrane in pressured water at 140 °C for 24 h. Furthermore, the introduction of aliphatic segment a hexane-1,6-diamine (HDA) in copolymer led to a significant increase in proton conductivity and water uptake with increasing temperature; the proton conductivity of the Ic-70 membrane reached 0.212 S cm⁻¹ at 80 °C, which was higher than Nafion 117 as well as of the membranes based on aromatic diamines at equivalent IEC values. Consequently, these materials proved to be promising as proton exchange membranes.     

Synthesis and properties of polynorbornenes bearing oligomeric siloxane pendant groups

The ring-opening metathesis polymerization (ROMP) of norbornene derivatives 1-5 bearing oligomeric siloxane pendant groups was carried out with Grubbs 1st and 2nd generation, and Grubbs-Hoveyda ruthenium (Ru) catalysts. Monomer 1 gave high-molecular-weight polymers (M_n ca. 27?000-180?000) in high yields (80-100%). Monomers 2-5 also polymerized with Ru carbene catalysts to give high-molecular-weight polymers (M_n ca. 34?000-240?000) in high yields (66-100%). The onset temperatures of weight loss (T₀) of the polymers were 180-250 °C. The glass transition temperatures (T_gs) of poly(1) and poly(2) bearing branched siloxane linkages were near or higher than room temperature (27 and 101 °C). Meanwhile, the T_gs of poly(3)-poly(5) bearing linear siloxane linkages were much lower (−115 to −23 °C), and decreased with increasing length of the siloxane linkages. Poly(1) and poly(2) were hydrogenated completely, which was confirmed by ¹H NMR spectroscopy. The free-standing membranes of poly(1) and poly(2) showed high gas permeability; especially poly(2) is the most permeable to various gases among ROMP-polynorbornene derivatives reported so far.     

Synthesis and electro-optical properties of helical polyacetylenes carrying carbazole and triphenylamine moieties

Novel chiral acetylene monomers bearing carbazole and triphenylamine groups, namely, (S)-3-butyn-2-yl 2-(9-carbazolyl)ethyl carbonate (1) and (S)-3-butyn-2-yl 4-(diphenylamino)benzoate (2) were synthesized, and polymerized with Rh⁺(nbd)[η⁶-C₆H₅B⁻(C₆H₅)₃] catalyst to give the corresponding polymers with moderate molecular weights (M_n 13.0 × 10³ and 15.5 × 10³) in good yields (86% and 88%). CD spectroscopic studies revealed that poly(1) and poly(2) took predominantly one-handed helical structure in CHCl₃. The helical structures of poly(1) and poly(2) were very stable against heating and addition of MeOH. The solution of poly(1) and poly(2) emitted fluorescence in 0.52% and 7.2% quantum yields, which were lower than those of the corresponding monomers 1 and 2 (22.5% and 76.5%). The cyclic voltammograms of the polymers indicated that the oxidation potentials of the polymers were lower than those of the monomers. The polymers showed electrochromism and changed the color from pale yellow to pale blue by application of voltage, presumably caused by the formation of polaron at the carbazole and triphenylamine moieties. The onset temperatures of weight loss of poly(1) and poly(2) were 225 and 270 °C under air.     

‘Living’ radical polymerization of styrene mediated by spiro ring-substituted piperidinyl-N-oxyl radicals. The effect of the spiro rings on the control of polymerization

The bulk radical polymerizations of styrene (St) at 80-120 °C in the presence of 6-aza-7,7-dimethyl-9-hydroxyspiro[4.5]decane-6-yloxyl (1) and 1-aza-2,2-dimethyl-4-hydroxy[5.5]undecane-1-yloxyl (2) were studied. At 100 and 120 °C, the polymerizations were well controlled by those nitroxides to give poly(St)s with narrow polydispersities. On the other hand, the polymerization mediated by 2 at 80 °C showed a good ‘livingness’ of polymerization, but 1 had a poor ability to control the polymerization to give poly(St) with a broad polydispersity of 1.52. The rate constants (k_act) for the homolysis of the NO-C bond of the alkoxyamines prepared from 1 and 2 were measured at 333-373 K, and the A_acts and E_acts values were determined to be 2.8×10¹³ s⁻¹ and 128 kJ mol⁻¹ (1) and 4.0×10¹³ s⁻¹ and 125 kJ mol⁻¹ (2), respectively, from the Arrhenius plots. These results are compared with those for the structurally related piperidinyl-N-yloxyl radicals including TEMPO.     

Ring-opening polymerization of six-membered cyclic esters catalyzed by tetrahydroborate complexes of rare earth metals

Catalytic behavior of tetrahydroborate complexes of rare earth metals, Ln(BH₄)₃(THF)_x (1: Ln = La, x = 3; 2: Ln = Pr, x = 2; 3: Ln = Nd, x = 3; 4: Ln = Sm, x = 3; 5: Ln = Y, x = 2.5; 6: Ln = Yb, x = 3), for ring-opening polymerization (ROP) of six-membered cyclic esters, δ-valerolactone (VL) and d,l-lactide (d,l-LA), was studied. The controlled polymerization of VL with 1-6 proceeded in THF at 60 °C. The catalytic activities of these complexes for the ROP of VL were observed to be in order of the ionic radii of the metals: 1(La) ≥ 2(Pr) ≥ 3(Nd) > 4(Sm) > 5(Y) > 6(Yb). The obtained polymers were demonstrated to be hydroxy-telechelic by ¹H NMR and MALDI-TOF MS spectroscopy. The controlled ROP of d,l-LA also proceeded by these complexes. The activities of these complexes for the d,l-LA ROP were also in order of the ionic radii of the metals.     

Geometrical influence of ABn monomer structure on the thermal properties of linear-hyperbranched ether-ketone copolymers prepared via an AB+ABn route

A series of poly(ether ketone) copolymers were prepared by nucleophilic aromatic polymerization reactions of 4-fluoro-4′-hydroxybenzophenone, 2, in the presence of varying percentages of AB_n monomers based on a triarylphosphine oxide platform, 1a (2F), 1b (4F), and 1c (6F), where A=OH and B=F. As expected, the crystallinity of the samples decreased with an increasing AB_n content. However, the tetrahedral geometry of the phosphine oxide-based AB_n monomers proved to be much more efficient at lowering the melt temperature of the copolymers than was the corresponding ketone-based AB_n monomer, 3,5-bis(4-fluorophenylbenzoyl)phenol, 4, that possesses a structure more similar to that of 2. Polymerization of 2 in the presence of as little as 5 mol% of bis-(3,4,5-trifluorophenyl)-(4-hydroxyphenyl)phosphine oxide, 1c (6F), afforded a completely amorphous polymer with a glass transition temperature of 168 °C that was soluble in hot NMP and DMSO. The copolymers also exhibited excellent thermoxidative stability with a number of samples displaying 5% weight loss temperatures, in air, well in excess of 500 °C.